AT&T CRL32102, CRL32202, CRL32302, CRL32352, CRL32452 Abridged User Manual

CRL32102/CRL32202/CRL32302/
CRL32352/CRL32452
DECT 6.0 cordless telephone/
answering system with
caller ID/call waiting

Abridged user’s manual

This Abridged user’s manual provides you with basic installation and
major operation instructions. A limited set of features are described in an
abridged form.

Please refer to the online CRL32102/CRL32202/CRL32302/CRL32352/

CRL32452 DECT 6.0 cordless telephone/answering system with
caller ID/call waiting Complete user’s manual for a full set of installation

and operation instructions at www.telephones.att.com/manuals.
For customer service, visit our website at www.telephones.att.com or

call 1 [phone]. In Canada, dial 1 [phone].

This telephone system is compatible with certain AT&T DECT 6.0 cordless
headsets. Visit www.telephones.att.com/headsets for a list of
compatible cordless headsets.

Serial number: __________________________________________________________

Purchase date: _________________________________________________________

Place of purchase: ______________________________________________________________

Both the model and serial numbers of your AT&T product can be found on
the bottom of the telephone base.

Save your sales receipt and original packaging in case it is necessary to
return your telephone for warranty service.

Model number:

Type:

CRL32102 (one handset)
CRL32202 (two handsets)
CRL32302 (three handsets)
CRL32352 (three handsets)
CRL32452 (four handsets)

DECT 6.0 cordless telephone/answering system
with caller ID/call waiting

© 2012-2014 Advanced American Telephones. All Rights Reserved. AT&T and
the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

Your telephone package contains the following items. Save your sales receipt
and original packaging in the event warranty service is necessary.

Power adapter for
telephone base

Telephone base

Abridged user’s manual Quick start guide

Wall mount bracket

Charger for cordless handset
with power adapter installed

(1 for CRL32202)
(2 for CRL32302/CRL32352)
(3 for CRL32452)

Cordless handset
(1 for CRL32102)

(2 for CRL32202)
(3 for CRL32302/CRL32352)
(4 for CRL32452)

Battery for cordless handset
(1 for CRL32102)

(2 for CRL32202)
(3 for CRL32302/CRL32352)
(4 for CRL32452)

Battery compartment cover
(1 for CRL32102)

(2 for CRL32202)
(3 for CRL32302/CRL32352)
(4 for CRL32452)

BY 1021

BT183342/BT283342

2.4V 400mAh Ni-MH

Telephone line cord

Caller ID

Announce

Abridged user’s manual

CRL32102/CRL32202/
CRL32302/CRL32352/CRL32452
DECT 6.0 cordless telephone/
answering system with
caller ID/call waiting

Telephone base installation

If you have DSL
high-speed Internet
service, a DSL filter (not
included) is required.
The DSL filter must
be plugged into the
telephone wall jack.

This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user’s
manual provided in the package, or see the online Complete
user’s manual at www.telephones.att.com/manuals.

Plug the power
adapter into an
electrical outlet
not controlled by a
wall switch.

Charger installation

Quick start guide

CRL32102/CRL32202/CRL32302/CRL32352/CRL32452

Plug the power
cord and telephone
line cord into

the jacks.

Route the
cords through
the slots.

Plug the other end of the
telephone line cord into a
telephone jack or a DSL filter.

Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
our website at www.telephones.att.com or call 1 [phone].
In Canada, dial 1 [phone].

Abridged user’s manual

CRL32102/CRL32202/CRL32302/
CRL32352/CRL32452
DECT 6.0 cordless telephone/
answering system with
caller ID/call waiting

Getting started

Quick reference guide - handset ........1

Quick reference guide - handset ........2

Telephone base and charger

installation ...............................................3

Telephone base installation ............3

Charger installation .............................3

Battery installation and charging ....... 4

Installation options .................................... 5

Tabletop to wall mount

installation.............................................5

Telephone settings

Handset settings .........................................6

Ringer volume ........................................ 6

Ringer tone ..............................................6

LCD language ......................................... 6

Set date/time .........................................7

Caller ID announce .............................. 7

Set speed dial voicemail number ...8

Voicemail (visual message

waiting) indicator ..................................8

Clear voicemail indicator ..................8

Key tone ....................................................9

Home area code .................................... 9

Dial mode .................................................9

QUIET mode ......................................... 10

Telephone operation

Handset operation .................................. 11

Making a call ........................................11

Answering a call ................................ 11

Ending a call ........................................ 11

Temporary ringer silencing ........... 11

Speakerphone ..................................... 11

Last number redial ............................ 11

Equalizer ................................................. 11

Volume control ................................... 12

Call waiting ........................................... 12

Mute ......................................................... 12

Handset locator .................................. 12

Join a call in progress .....................12

Chain dialing ........................................ 13

Blind transfer ....................................... 13

Multiple handset use

Intercom ....................................................... 14

Call transfer using intercom .............. 15

Directory

Directory ......................................................16

Create a new directory entry ...... 16

Review directory entries ................ 17

Search by name.................................. 17

Delete a directory entry ................. 17

Edit a directory entry ....................... 17

Speed dial .................................................. 18

Assign a speed dial number......... 18

Assign your speed dial

voicemail number .............................. 18

Table of contents

For more detailed instructions, refer to the Complete user’s
manual at www.telephones.att.com/manuals.

Make a call using speed dial ....... 18

Check your voicemail using

speed dial .............................................. 18

Caller ID

Caller ID .......................................................19

Information about caller ID

with call waiting ................................. 19

Missed (new) call indicator ........... 19

Review the caller ID history ......... 19

Dial a caller ID log entry ............... 19

View dialing options ......................... 19

Save a caller ID log entry to the

directory ................................................. 20

Answering system

Answering system settings ................. 21

Announcement ................................... 21

Answer on/off ..................................... 22

Call screening ...................................... 22

Number of rings .................................23

Remote access code ........................ 23

Message alert tone ........................... 24

Message recording time ................. 24

About the answering system............. 25

Answering system and

voicemail indicators.......................... 25

Using the answering machine

and voicemail together .................. 25

Message capacity .............................. 26

Voice prompts ..................................... 26

Call screening at the

telephone base ................................... 26

Call screening at the handset ..... 26

Call intercept ....................................... 26

Temporarily turning off the

message alert tone ........................... 26

Message playback ................................... 27

Options during playback ................ 27

Delete all old messages ................. 28

Recording and playing memos ......... 28

Record a memo .................................. 28

Play back a memo ............................ 28

Remote access .......................................... 29

Appendix

Adding and registering

handsets/headsets ................................. 30

Register a handset to your

telephone base ................................... 30

Deregistering handsets ........................ 31

Deregister all handsets from

your telephone base ........................ 31

Troubleshooting ....................................... 32

Maintenance............................................... 35

Important safety information ............36

Safety information ............................. 36

Especially about cordless

telephones ............................................ 37

Precautions for users of

implanted cardiac pacemakers ... 37

Pacemaker patients .......................... 37

Especially about telephone

answering systems ............................ 37

For C-UL compliance ............................. 38

Mesures de sécurité

importantes .......................................... 38

FCC Part 68 and ACTA .......................... 41

FCC Part 15 ................................................ 42

Limited warranty ...................................... 43

Technical specifications .......................45

DECT 6.0 digital technology ......... 45

Telephone operating range ..........45

HD audio ................................................ 45

Index

Index .............................................................. 46

1

Quick reference guide - handset

Getting started

Audio Assist is a registered trademark of Advanced American Telephones.

CHARGE indicator

On when the handset is
charging in the telephone base
or charger.

qCID/VOLUME

Press qCID to show the
caller ID history (page 19).

Press to scroll down while
in menus.

While entering names or
numbers, press to move the
cursor to the left.

Press to decrease the listening
volume when on a call, or to
decrease the message playback
volume (page 27).

PHONE/FLASH

Press to make or answer a call.
During a call, press to answer an

incoming call when you receive
a call waiting alert (page 12).

1

While reviewing a caller ID
log entry, press repeatedly to
add or remove 1 in front of
the telephone number before
dialing or saving it in the
directory (page 19).

Press and hold to set (page 8)
or dial your voicemail number
(page 18) when the handset is
not in use.

MUTE/DELETE

During a call, press to mute the microphone.
While reviewing the caller ID history, the

directory or the redial memory, press to delete
an individual entry.

While predialing, press to delete digits.
While editing numbers or names in the

directory, press to delete digits or characters, or
press and hold to delete all digits or characters.

/SPEA�ERSPEA�ER

Press to switch between the
speakerphone and the handset
(page 11).

QUIET # (pound key)

Press repeatedly to display
other dialing options when
reviewing a caller ID log entry
(page 19).
Press and hold to enter the
QUIET mode setting screen, or to
deactivate QUIET mode (page 10).

OFF/CANCELOFF/CANCEL

During a call, press to hang up.
While in menus, press to cancel

an operation, back up to the
previous menu, or exit the
menu display; or press and hold
this key to exit to idle mode.

Press and hold while the
telephone is not in use to erase
the missed call indicator.

MENU/SELECT

Press to show the menu.
While in the menu, press to

select an item or save an entry
or setting.

pDIR/VOLUME

Press pDIR to show directory
entries (page 17).

Press to scroll up while in menus.
While entering names or

numbers, press to move the
cursor to the right.

Press to increase the listening
volume when on a call (page 12),
or to increase the message
playback volume (page 27).

TONE

Press to switch to touch-tone
dialing temporarily during a call
if you have pulse service.

REDIAL/PAUSE

Press repeatedly to view
the last 10 numbers dialed
(page 11).

While saving numbers into the
directory,

press and hold

to

insert a dialing pause (page 16).

AUDIO ASSIST

During a call, press to enhance
the clarity and loudness of your
caller’s voice.

Incoming call light

Flashes when there is a incoming call or
when the base is paging the handset.

2

Getting started

Quick reference guide - handset

EQ

During an outside call, intercom call, message
or announcement playback, press to change
the quality of the audio to best suit your
hearing (page 11).

Handset
side view

Quick reference guide - telephone base - telephone base

Caller ID

Announce

IN USE indicator

On when the handset is in use, or when the
answering system is answering an incoming call.

On when a handset is being registered.
Flashes when there is an incoming call or

when handsets are being deregistered.
Flashes when another telephone is in use on

the same line.

/PLAY/STOP

Press to start or
stop message
playback (page 27).

/S�IP

Press to skip a
message (page 27).

/REPEAT

Press to repeat a
message.

Press twice to
play the previous
message (page 27).

X/DELETE

Press to delete the message currently playing
(page 27).

Press twice to delete all old messages when the
phone is not in use (page 28).

/ANS ON

Press to turn the built-in answering
system on or off (page 22).

VOLq and VOLp

During message
playback, press to
adjust the listening
volume (page 27).

While in idle mode,
press to adjust the
base ringer volume.

/HANDSET LOCATOR

While the phone is idle, press to
page all handsets (page 12).

Incoming call light

Flashes when there is a
incoming call.

SLOW

Press to slow
down the message
playback (page 27).

Message counter

Shows the number
of messages or other
answering system
information.

Shows the base ringer
volume or playing
message volume.

Getting started

3

Telephone base and charger installation

Install the telephone base and charger, as shown below.

IMPORTANT INFORMATION

Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, visit our website at www.telephones.att.com or call

1 [phone]. In Canada, dial 1 [phone].

For more detailed instructions, refer to the online Complete user’s manual at

www.telephones.att.com/manuals.

The power adapters are intended to be correctly oriented in a vertical or floor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.

1.

2.

Charger installation

Telephone base installation

Plug the large end of the
charger power adapter into an
electrical outlet not controlled
by a wall switch.

Telephone line cord

A DSL filter (not included)
is required if you have
DSL high-speed Internet
service. The DSL filter
must be plugged into the
telephone wall jack.

Plug the small end of
the telephone base
power adapter into the
power jack on the back
of the telephone base.

Plug the large end of
the telephone base
power adapter into an
electrical outlet not
controlled by a wall
switch.

Plug the other end
of the telephone line
cord into the TEL. LINE
jack on the back of the
telephone base.

Plug one end of the
telephone line cord
into a telephone jack
or a DSL filter.

Route the cords
through the channels.

Telephone base

Charger

4

Getting started

Battery installation and charging

Once you have installed the battery, the screen indicates the battery status
(see the following table). For best performance, keep the handset in the
telephone base or charger when not in use. The battery is fully charged
after 10 hours of continuous charging. See the table in the Technical

specifications section on page 45 for battery operating times.

Battery indicators Battery status Action

The screen is blank, or
shows Place in charger
and (flashing).

Battery has no or
very little charge. The
handset cannot be used.

Charge without interruption
(at least 30 minutes).

The screen shows
Low battery and
(flashing).

Battery has enough
charge to be used for a
short time.

Charge without interruption
(at least 30 minutes).

The screen shows
HANDSET X.

Battery is charged. To keep the battery charged, place it in the

telephone base or charger when not in use.

Step 1

Plug the battery
connector securely
into the socket inside
the handset battery
compartment. Insert the
supplied battery with
the label THIS SIDE UP
facing up, as indicated.

Step 2

Align the cover flat against
the battery compartment,
then slide it upwards until
it clicks into place.

Step 3

Charge the handset by placing it face forward in the
telephone base or charger. The CHARGE light on the
handset is on during charging.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or
replacement battery (model BT183342). To order, visit

our website at www.telephones.att.com or call

1 [phone]. In Canada, dial
1 [phone]. For more detailed instructions,

refer to the online Complete user’s manual at

www.telephones.att.com/manuals.

2. If you do not use the handset for a long time, disconnect
and remove the battery to prevent possible leakage.

Battery Pack

BT183342 2.4V 400mAh Ni-MH

WARNING: DO NOT BURN OR

PUNCTURE BATTERIES

MADE IN CHINA

MANUFACTURED BY BYD BYYYWW

CHARGE light

Getting started

5

Installation options

Your telephone base is ready for tabletop use. If you want to mount your
telephone on a wall, use the provided wall mount bracket to connect with
a standard dual-stud telephone wall mounting plate. If you do not have this
mounting plate, you can purchase one from many hardware or consumer
electronics retailers. You might need a professional to install the mounting plate.

Tabletop to wall mount installation

With the upper tabs (marked A) on top, align the holes of the wall mount
bracket with the studs on the standard wall mounting plate and slide the
bracket down until it locks securely.

Plug one end of the telephone line cord into the jack on the bottom of the
telephone base and plug the other end into the telephone wall jack (or
DSL filter). Plug the small end of the telephone base power adapter into
the jack on the bottom of the telephone base and plug the other end into
an electrical outlet not controlled by a wall switch. Route the telephone
line cord and the power cord through the grooves at the bottom of the
telephone base, accordingly.

Hold the cords to the side of the telephone base. Align the upper slots
on the back of the telephone base just above the upper tabs (marked A)
of the wall mount bracket. Make sure the lower slots of the telephone
base are also aligned above the lower tabs (marked B) of the wall mount
bracket. Push the telephone base down until it clicks securely in place.

Bundle the telephone line cord and power adapter cord neatly with twist ties.

1.

2.

3.

4.

1

2

4

3

6

Handset settings

Use the menu to change the telephone settings.

Press MENU/SELECT when the telephone is not in use to enter the main
menu.

Press qCID or pDIR to scroll to the feature to be changed. When scrolling
through the menu, the > symbol indicates the highlighted menu item.

Press MENU/SELECT to select the highlighted item.

NOTE: Press OFF/CANCEL to cancel an operation, back up to the previous menu or
exit the menu display. Press and hold OFF/CANCEL to return to idle mode.

Ringer volume

You can adjust the ringer volume level or turn the ringer off.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press MENU/SELECT.

3. Press MENU/SELECT again to select >Ringer volume.

4. Press qCID or pDIR to sample each volume level.

5. Press MENU/SELECT to save your preference.

NOTE: The handset ringer volume also determines the ringer volume for intercom calls.

Ringer tone

You can choose one of 10 ringer tones.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press MENU/SELECT.

3. Press qCID or pDIR to scroll to >Ringer tone, then press MENU/SELECT.

4. Press qCID or pDIR to sample each ringer tone.

5. Press MENU/SELECT to save your preference.

NOTE: If you turn off the ringer volume, you do not hear ringer tone samples.

LCD language

You can select English, French, or Spanish to be used for all screen displays.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Press MENU/SELECT to choose >LCD language.

4. Press qCID or pDIR to scroll to the desired language, then press

MENU/SELECT. The screen prompts Set English/Français/Español as

LCD language?

5. Press MENU/SELECT to confirm.

1.

2.

3.

Telephone settings

7

Telephone settings

Handset settings

NOTE: If you accidentally change the LCD language to French or Spanish, you can reset it

back to English without going through the French or Spanish menus. Press MENU/SELECT
in idle mode, then enter 364#. There is a confirmation tone.

Set date/time

The answering system announces the day and time of each message prior
to playing it. Before using the answering system, set the date and time as
follows. If you subscribe to caller ID service, the day, month and time are
set automatically with each incoming call. The year must be set so that the
day of the week can be calculated from the caller ID information.

When the handset is in idle mode, press MENU/SELECT to enter the main menu.
Press qCID or pDIR to scroll to >Set date/time and then press MENU/

SELECT.

Enter the month using the dialing keys.
Enter the day using the dialing keys.
Enter the year using the dialing keys, then press MENU/SELECT to move on

to set the time.
Enter the hour using the dialing keys.
Enter the minute using the dialing keys.
Press qCID or pDIR to highlight AM or PM, then press MENU/SELECT to confirm.

NOTE: If the clock is not set when a message is recorded, the system announces, “Time and
day not set,” before it plays the message.

Caller ID announce

The caller ID announce feature lets you know who’s calling without having to
look at the display.

To turn on/off the caller ID announce feature on your handset or base:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Caller ID annc, then press MENU/SELECT.

4. Use qCID or pDIR to highlight the desired option, then press MENU/SELECT.

Set all On/Off - Change the setting for the base and all handsets.
Local handset - Change the setting for that handset only.
Base - Change the setting for the telephone base only.

5. Use qCID or pDIR to highlight >On or >Off, then press MENU/SELECT.

NOTES:

To use the caller ID announce feature, you must subscribe to caller ID service from your
telephone service provider.

Pronunciation of names may vary with this feature. Not all names may be pronounced correctly.

1.

2.

3.

4.

5.

6.

7.

8.

•

•

•

•

•

Telephone settings

8

Handset settings

Set speed dial voicemail number

This feature lets you save your voicemail number for quick access when you
press and hold the 1 key.

To set your voicemail number:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Voicemail #, then press MENU/SELECT.

4. Use the dialing keys to enter the voicemail access number provided by
your telephone service provider.

Press qCID or pDIR to move the cursor to the left or right.
Press MUTE/DELETE to erase a digit.
Press and hold MUTE/DELETE to erase all digits.
Press REDIAL/PAUSE to enter a three-second dialing pause (a p appears).

5. Press MENU/SELECT to save.

Voicemail (visual message waiting) indicator

If you subscribe to a voicemail service offered by your telephone service
provider, New voicemail and the icon appear on the handset screen when
you have new voicemail messages. Contact your service provider for more
information and assistance about using your voicemail service.

Clear voicemail indicator

Use this feature when the telephone indicates there is new voicemail but
there is none. For example, when you have accessed your voicemail while
away from home. This feature only turns off the displayed New voicemail
and the icon; it does not delete your voicemail messages. As long as you
have new voicemail messages, your telephone service provider continues to
send the signal to turn on the indicator.

To manually turn off the new voicemail indicator:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Clr voicemail, then press MENU/SELECT.
The screen shows Reset Voicemail Indicator?

4. Press MENU/SELECT again to turn the voicemail indicator off.

NOTE: For information about using your voicemail service, contact your telephone

service provider.

•

•

•

•

9

Telephone settings

Handset settings

�ey tone

The handset is set to beep with each key press. You can adjust the key tone
volume or turn it off.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >�ey tone, then press MENU/SELECT.

4. Use qCID or pDIR to select the desired volume or Off.

5. Press MENU/SELECT to save your preference.

Home area code

If you dial seven digits to make a local call (no area code required), enter your area
code into the telephone as the home area code. When you receive a call from
within your home area code, the caller ID history only displays the seven digits of
the telephone number.

This feature makes it easy for you to place a call from the caller ID log. If you
dial 10 digits to make a local phone call, do not use this home area code
feature. If you do, you cannot place local calls from your caller ID log, as they
will have only seven digits.

To set the home area code:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Home area code, then press MENU/SELECT.

4. Use the dialing keys to enter a three-digit home area code.

Press MUTE/DELETE to delete a digit.
Press and hold MUTE/DELETE to delete all digits.

5. Press MENU/SELECT to save.

NOTE: If in the future, your telephone service provider requires you to dial 10 digits to

make a local call (area code plus telephone number), you need to delete your home
area code and dial out locally from the caller ID log. With the home area code displayed,
press and hold MUTE/DELETE until the digits are deleted, and then press MENU/SELECT.
The home area code is now restored to its default setting of _ _ _ (empty).

Dial mode

The dial mode is preset to tone dialing. If you have pulse (rotary) service, you
must change the dial mode to pulse dialing before using the telephone.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press MENU/SELECT.

3. Use qCID or pDIR to scroll to >Dial mode, then press MENU/SELECT.

4. Use qCID or pDIR to highlight >Touch-tone or >Pulse, then, press

MENU/SELECT.

•

•

Telephone settings

10

Handset settings

QUIET mode

When QUIET mode is turned on, the telephone silences all sounds (except the
handset locator paging tone) during the set period of time (1-12 hours). After
you turn on QUIET mode, this feature activates immediately and the answering
system turns on automatically. When QUIET mode is on, the answering system
takes calls and records messages without broadcasting them.

To turn QUIET mode on:

Press and hold QUIET # when the handset is not in use.
Using the dialing keys (0-9) to enter the duration, then press SELECT to

save.

To turn QUIET mode off:

Press and hold QUIET # when the handset is not in use.

NOTES:

If you change the base ringer, handset ringer, ringer volume, key tone, or caller ID
announce features when QUIET mode is on, the sample plays but the feature is still
muted after saving the setting.

After QUIET mode is turned off or the set period of time has expired, all muted
features will be activated again.

Intercom is available during QUIET mode, but the handset will not ring.

1.

2.

•

•

•

•

Telephone operation

11

Handset operation

Making a call

Press PHONE/FLASH or /SPEA�ERSPEA�ER, then enter the telephone number.

Answering a call

Press PHONE/FLASH or /SPEA�ERSPEA�ER.

-OR­Press any dialing key (0-9, TONE or #).

Ending a call
Press OFF/CANCEL or return the handset to the telephone base or charger.

Temporary ringer silencing

Press OFF/CANCEL or MUTE/DELETE while the telephone is ringing to
silence the ringer temporarily on that handset only. This turns off the ringer
without disconnecting the call. The next incoming call rings normally at the
preset volume.

Speakerphone

During a call, press /SPEA�ERSPEA�ER to switch between handsfree speakerphone
and normal handset use. Press OFF/CANCEL to hang up.

NOTE: The speakerphone uses more power than the normal handset. If the handset battery

becomes very low while you are using the speakerphone, the call remains in speakerphone
mode until you hang up or the battery becomes depleted.

Last number redial

Each handset stores the last 10 telephone numbers dialed (up to 30 digits).
Press REDIAL/PAUSE, then press qCID or pDIR, or press REDIAL/PAUSE

repeatedly to view up to 10 recently called numbers. Press PHONE/FLASH
or /SPEA�ERSPEA�ER to dial the displayed number.

Equalizer

The equalizer feature on the handset enables you to change the quality of
the audio to best suit your hearing.

While on a call or intercom call, or listening to a message or announcement,
press EQ to select the equalizer setting Treble 1, Treble 2, Bass or
Natural (the default setting).

•

•

•