AT&T CL83101, CL83201, CL83301, CL83451, CL83351 User Manual

...
Quick start guide (Canada version)
CL83101/CL83201/ CL83301/CL83351/ CL83401/CL83451 DECT 6.0 cordless telephone/ answering system with caller ID/call waiting
Installation
You must install and charge the battery before using the telephone.
Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base can be placed on a flat surface or vertically mounted on the wall. For optimum range and better reception, place the telephone base in a central and open location.
If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone line, you must install a DSL filter between the telephone line cord and the telephone wall jack (see the following page). The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters.
Your product may be shipped with protective stickers covering the handset and telephone base displays - remove them before use.
For customer service or product information, visit our website at
STOP!
See page 3 for easy instructions.
www.telephones.att.com or call 1 (866) 288-4268.
Avoid placing the telephone base too close to:
Communication devices such as television sets, VCRs, or other
• cordless telephones.
Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
• ovens, refrigerators, or fluorescent lighting.
Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of a washing machine
• or workbench.
1
Telephone base and charger installation
Install the telephone base and charger as shown below.
Telephone base installation
Plug the large end of the power adapter into a power outlet not controlled by a wall switch.
If you have DSL high-speed Internet service, a DSL filter (not included) is required.
Route the power adapter cord through this slot.
Raise the antenna.
Plug the small end of the telephone base power adapter into the power adapter jack on the back of the telephone base.
Telephone line cord
Plug one end of the telephone line cord into a telephone jack or a DSL filter.
Route the telephone line cord through this slot.
Plug the other end of the telephone line cord into the telephone jack on the back of the telephone base.
Charger installation
Plug the power adapter into an electrical outlet not controlled by a wall switch.
IMPORTANT INFORMATION
Use only the power adapter(s) supplied with this product. To order a replacement
• power adapter, visit our website at www.telephones.att.com or call
1 (866) 288-4268.
The power adapters are intended to be correctly oriented in a vertical or floor
• mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
2
Battery installation and charging
BY 1021
BT183342/BT283342
Once you have installed the battery, the screen indicates the battery status. For best performance, keep the handset in the telephone base or charger when not in use. The battery is fully charged after 10 hours of continuous charging.
NOTE: If you are on a phone call in low battery mode, you hear four short beeps every minute.
CHARGE light
Step 1
Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label. Insert the supplied battery with the label THIS SIDE UP facing up as indicated.
Step 3
Charge the handset by placing it face forward in the telephone base or charger. The CHARGE light on the top of the handset is on during charging.
Step 2
Align the cover flat against the battery compartment, then slide it upwards until it clicks into place.
After you install your telephone or power returns following a power outage, the handset will prompt you to set the date and time. For instructions, see
Set date/time on page 8. To skip, press OFF/CANCEL.
IMPORTANT INFORMATION
Use only the supplied rechargeable battery or replacement battery (model BT166342).
To order, visit our website at www.telephones.att.com or call
1 (866) 288-4268.
If you do not use the handset for a long time, disconnect and remove the battery
• to prevent possible leakage.
3
Quick reference guide - handset
CHARGE indicator
On when the handset is charging in the telephone base or charger.
qCID/VOLUME
Press qCID to show caller ID history when the handset is not in use.
Press to scroll down while in menus.
While entering names or numbers, press to move the cursor to the left.
Press to decrease the listening volume when on a call, or to decrease the message playback volume.
MUTE/DELETE
During a call, press to mute the microphone.
When the handset is ringing, press to mute the ringer temporarily.
While reviewing the caller ID history, the directory or the redial memory, press to delete an individual entry.
While predialing, press to delete digits.
During message or announcement playback, press to delete the playing message or the recorded announcement
.
PHONE/FLASH
Press to make or answer a call. During a call, press to answer
an incoming call when you receive a call waiting alert.
During message playback, press to call back the caller if caller’s number is available.
1
While reviewing a caller ID log entry, press repeatedly to add or remove 1 in front of the telephone number before dialing or saving it in the directory.
TONE
Press to switch to tone dialing temporarily during a call if you have pulse service.
/SPEA�ERSPEA�ER
Press to make or answer a call using the speakerphone.
Press to switch between the speakerphone and the handset.
4
pDIR/VOLUME
Press pDIR to show directory entries when the handset is not in use.
Press to scroll up while in menus.
While entering names or numbers, press to move the cursor to the right.
Press to increase the listening volume when on a call, or to increase the message playback volume.
MENU/SELECT
When the handset is not in use, press to show the menu.
While in the menu, press to select an item or save an entry or setting.
OFF/CANCEL
During a call, press to hang up.
While in a menu, press to cancel an operation, back up to the previous menu, or exit the menu display, or press and hold this button to exit to idle mode.
When the handset is ringing, press to mute the ringer temporarily.
Press and hold while the telephone is not in use to erase the missed call indicator.
# (pound key)
Press repeatedly to display other dialing options when reviewing a caller ID log entry.
EQ
During an outside call, intercom call, message or announcement playback, press to change the audio quality to best suit your hearing.
REDIAL/PAUSE
Press repeatedly to view the last 10 numbers dialed.
While entering numbers, press and hold to insert a dialing pause.
Loading...
+ 9 hidden pages