Quick start guide
CL81109/CL81209/CL81309
DECT 6.0 cordless
telephone with caller ID/
call waiting
Installation
You must install and charge
the battery before using the
telephone.
Install the telephone base close to a telephone jack and a power outlet not
controlled by a wall switch. The telephone base can be placed on a flat surface
or vertically mounted on the wall (read the user’s manual for details). For
optimum range and better reception, place the telephone base in a central and
open location.
If you subscribe to high-speed Internet service (digital subscriber line DSL) through your telephone line, you must install a DSL filter between the
telephone line cord and the telephone wall jack (see the following page). The
filter prevents noise and caller ID problems caused by DSL interference. Please
contact your DSL service provider for more information about DSL filters.
Your product may be shipped with a protective sticker covering the handset or
telephone base display - remove it before use.
For customer service or product information, visit our website at
STOP!
See pages 4-5
for easy instructions.
www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial
1 (866) 288-4268.
Avoid placing the telephone base too close to:
Communication devices such as: television sets, VCRs, or other cordless
•
telephones.
•
Excessive heat sources.
Noise sources such as a window with traffic outside, motors, microwave
•
ovens, refrigerators, or fluorescent lighting.
•
Excessive dust sources such as a workshop or garage.
Excessive moisture.
•
•
Extremely low temperature.
Mechanical vibration or shock such as on top of the washing machine or
•
workbench.
1
Telephone base installation
Install the telephone base as shown below.
The telephone base is ready for tabletop use. If you want to change to wall
mounting, read the user’s manual for details.
2. Route the power
1. Plug the small end
of the power adapter
into the power jack
on the bottom of the
telephone base.
7. Raise the antenna.
adapter cord
through the slot.
3. Plug one end of the
telephone line cord
into the telephone jack
on the bottom of the
telephone base.
4. Place the cords into
the channels.
6. Plug the large end
of the power adapter
into a power outlet
not controlled by a
wall switch.
If you have
DSL high speed
Internet service,
a DSL filter (not
included) is
required.
5. Plug the other end
of the telephone line
cord into a telephone
jack or a DSL filter.
IMPORTANT INFORMATION
1. Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, visit our website at www.telephones.att.com, or call
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
2. The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
2
Charger installation
Install the charger as shown below.
Plug the power adapter
into an electrical outlet
not controlled by a wall
switch.
IMPORTANT INFORMATION
1. Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, visit our website at www.telephones.att.com, or call
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
2. The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
3
Battery installation & charging
Install the battery as shown on the next page. Once you have installed the
battery, the screen indicates the battery status (see table below). If necessary,
place the handset in the telephone base or charger to charge the battery.
For best performance, keep the handset in the charger when not in use. The
battery is fully charged after 16 hours of continuous charging. See the table on
the Technical specifications page of the user’s manual for battery
operating times.
If the screen is blank, you need to charge the handset without interruption for
at least 10 minutes to give the handset enough charge to use the telephone
for a short time. The screen shows LOW BATTERY and the backlight is off until
you have charged the battery without interruption for at least one hour. The
following table summarizes the battery charge indicators and actions to take.
Battery indicators Battery status Action
The screen is blank. Battery has no charge and
the handset cannot be used.
The screen shows PLACE IN
CHARGER and flashes.
The screen shows LOW
BATTERY and flashes.
The screen shows
HANDSET X.
Battery has very little charge
and the handset cannot be
used.
Battery has enough charge
to be used for a short time.
Battery is charged. To keep the battery charged,
Charge without interruption until
the screen shows LOW BATTERY
(at least 10 minutes).
Charge without interruption until
the screen shows LOW BATTERY
(at least four minutes).
Charge without interruption until
the screen shows HANDSET X (at
least one hour).
place it in the telephone base or
charger when not in use.
NOTE: If you are on a phone call in low battery mode, you hear four short beeps every
minute.
4
Battery installation & charging
Step 1
Plug the battery connector
securely into the socket
inside the handset battery
compartment, matching the
color-coded label. Insert
the supplied battery with
the label THIS SIDE UP
facing up as indicated.
Step 3
Charge the handset by placing it face up in the
telephone base or charger. The CHARGE light is on when
charging.
Align the cover flat against
the battery compartment,
then slide it upwards until it
clicks into place.
Step 2
CHARGE light
IMPORTANT INFORMATION
1. Use only the supplied rechargeable battery or replacement battery (model BT8001).
To order, visit our website at www.telephones.att.com or call 1 (800)
222-3111. In Canada, dial 1 (866) 288-4268.
2. If you do not use the handset for a long time, disconnect and remove the battery to
prevent possible leakage.
5
Quick reference guide - handset
CHARGE indicator
On when the handset is
charging in the telephone base
or charger.
qCID/-VOLUME
Press qCID to show caller ID
history.
Press to scroll down while in
menus.
While entering names or
numbers, press to move the
cursor to the left.
Press to decrease the listening
volume when on a call.
PHONE/FLASH
Press to make or answer a call.
During a call, press to answer
an incoming call when you
receive a call waiting alert.
1
While reviewing a call log
entry, press repeatedly to
add or remove 1 in front of
the telephone number before
dialing or saving it in the
directory.
MUTE/DELETE
During a call, press to mute the
microphone.
While reviewing the caller ID
history, the directory or the
redial memory, press to delete
an individual entry.
While predialing, press to
delete digits.
SPEAKER
Press to switch between
speakerphone and handset.
MENU/SELECT
Press to show the menu.
While in the menu, press to
select an item or save an entry
or setting.
DIRp/+VOLUME
Press DIRp to show directory
entries.
Press to scroll up while in
menus.
While entering names or
numbers, press to move the
cursor to the right.
Press to increase the listening
volume when on a call.
OFF/CLEAR
During a call, press to hang up.
While in a menu, press to
cancel an operation, back up to
the previous menu, or exit the
menu display.
Press and hold while the
telephone is not in use to erase
the missed calls indicator.
#
Press repeatedly to display
other dialing options when
reviewing a call log entry.
REDIAL/PAUSE
Press repeatedly to view the
last five numbers dialed
While entering numbers, press
and hold to insert a dialing
pause.
INT
Press to begin an intercom
conversation or to transfer a
call.
6
Quick reference guide - handset
Main menu
> Shows a highlighted
item
>DIRECTORY
CALL LOG
Menu
Main menu
DIRECTORY
CALL LOG
RINGER VOLUME
RINGER TONE
KEY TONE
LCD LANGUAGE
SET DATE/TIME
CLR VOICEMAIL
HOME AREA CODE
Using menus
Press MENU/SELECT to show the first menu
item, DIRECTORY.
Press qCID or DIRp to scroll through menu
items.
Press MENU/SELECT to select or save
changes to a highlighted menu item.
Press OFF/CLEAR to cancel an operation,
back up to the previous menu, or exit the
menu display.
7
Quick reference guide - telephone base
IN USE indicator
On when the handset is
in use or when you are
registering a handset.
Flashes when another
telephone is in use on the
same line, or when you are
deregistering handset(s)
from the telephone base.
Flashes quickly when there
is an incoming call.
VOICEMAIL indicator
Flashes when you have new
voicemail. Voicemail service
is offered by your local
telephone company.
HANDSET LOCATOR
Press to make handsets
beep so you can locate
them.
8
www.telephones.att.com
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
© 2009 Advanced American Telephones. All Rights Reserved.
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 4 AT&T 09/09.
Loading...