AT&T BTH20 User Manual

Download

Page 1

Bluetooth®/Wired Headphones

Bluetooth

Headphones

user’s manual

model #: BTH20

Page 2

hello.

What’s Included

Unpack the Bluetooth® headphones and make sure all accessories are put aside so they will not be lost.

Thank you for purchasing the AT&T Bluetooth®/wired headphones [BTH20].

Bluetooth® Headphones

Features

· Bluetooth 4.0 technology with amazing sound

· Built-in microphone with echo cancellation

· Full controls for playback and calls

· Portable folding design

· 3.5 mm auxilary input jack

Bluetooth Headphones

Audio CordMicro USB Cable

Page 2 Page 3

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

Page 3

Page 4

Introduction

What’s Included

Safety Information

Getting Started Location of Main Unit Controls

Operational Instructions

Charging Power ON/OFF Pairing Making Phone Calls Listening to Music

Troubleshooting

Compliance with FCC Regulations

Warranty Information

Speciﬁcations

7 7 7 8 9

Contents Safety Information

Page 5

Important Safety Instructions

1. ATTACHMENTS - Do not use attachments not recommended

by the manufacturer.

2. WATER AND MOISTURE - The unit should not be used near

water. For example: near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

3. VENTILATION - The unit should be situated so that its location

or position does not interfere with its proper ventilation. For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the ﬂow of air through the ventilation openings.

4. OBJECTS AND LIQUID ENTRY - Care should be taken so that

external objects do not fall into and liquids are not spilled onto any openings or vents located on the product.

5. POWER SOURCE - The unit should be connected to a power

supply only of the type described in the operating instructions or as marked on the unit. If you are not sure please consult the dealer or local power company.

6. HEAT - The unit should be situated away from heat sources

such as radiators, heat registers, stoves or other appliances (including ampliﬁers) that produce heat.

7. SERVICING - The user should not attempt to service the

unit beyond those methods described in the user’s manual. Opening or removing covers will expose you to dangerous voltage and other hazards. Service methods not covered in the user’s manual should be referred to qualiﬁed service personnel.

Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in this user’s manual and on the BTH20.

Page 4

Operational Instructions

Charging

Charge your BTH20 through any USB jack or wall charger. The LED indicator will begin to blink red when charging. Before using for the ﬁrst time, charge at least 4 hours. After the ﬁrst charge, the headset will charge in 2 to 3 hours and the LED indicator will stop blinking when the charge is complete.

Note: When the battery is fully charged, the LED indicator will change to

blue.

Power ON/OFF

Press and hold the ON/OFF button for 1 second to switch the headset on. The LED will ﬂash red when powered on. Press and hold the ON/OFF button for 3 seconds to switch the headset off. When powering off, the LED will ﬂash blue and then turn off indicating the headset is off.

Pairing

While the headset is off, press and hold the ON/OFF – Bluetooth Pairing buttons for 5 seconds to start pairing mode. Once the headset is in the pairing mode (the LED will ﬂash red and blue), select ‘BTH20’ among discovered Bluetooth devices on the phone. If requested, enter the password ‘0000’ to pair the headset. When connected, you will hear a beep and your mobile device will show “Paired”.

Note: If the headset does not pair with another Bluetooth device in 3

minutes, it will turn itself off.

Getting Started

Location of Main Unit Controls

1. Previous song / Volume +

2. Next song / Volume -

3. Play / Pause / Mute

4. ON/OFF / Pairing / Answer / Reject call / Redial

5. 3.5 mm input port

Page 6 Page 7

6 7 8

6. Micro USB charging port

7. LED

8. Microphone

Page 5

Operational Instructions

Making Phone Calls

Making a call

Once paired, use your mobile device to dial a number as usual. Once connected, the call will be heard on your BTH20 headset.

Last number redial Press the ON/OFF button to redial last number.

Note: For some mobile models, press the ON/OFF button twice.

Answer a call

When receiving a call, press the ON/OFF button to answer the call.

Ending a call While talking on the phone, press the ON/OFF button to end the call.

Rejecting a call While receiving a call, press and hold the ON/OFF button to refuse the call.

Volume control Use the Volume +/ Volume - buttons to adjust the volume level.

Call transfer During a phone conversation, press the Play/Pause button to switch the call between the headset and the phone.

Operational Instructions

Listening to Music

Play/Pause

Press the Play button to launch the phone’s music player and to start listening to music. While listening to music, press the Pause button to pause or to resume play.

Song Selection While music is playing, press the Next Song or Previous Song buttons to select songs.

Answer a call while listening to music When receiving a call, press the ON/OFF button to answer the call. Press the ON/OFF button while on the phone to end the call. When receiving a call, press and hold the ON/OFF button to reject the call. (Music will resume playing when the call is rejected.)

Volume control Use the Volume + and Volume - buttons to adjust the volume level.

Purple light ﬂashes & red light blinks

Status

Powering ON

Powering OFF

Low battery

Charging

Pairing mode

Connection complete

Incoming call & on the phone

Playing music

LED indicator

Purple light dims & disappears

Blinking red & headset emits a beep

Solid red

Blue and red lights ﬂashing rapidly

Blue light blinks every 2 seconds

Solid blue

Blinking blue light

LED Indicator Chart

Page 8 Page 9

Page 6

Compliance with FCC Regulations

The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate Radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to Radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to Radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced Radio/television technician for assistance.

THE SPECIFICATION AND EXTERNAL APPEARANCE OF THE PRODUCT ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE.

If at any time in the future you should need to dispose of this product, please note that waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Troubleshooting

Symptom

Music is not streaming over Bluetooth

No power

BTH20 does not answer phone calls

Music does not resume after ending a call

Not able to control music from the BTH20

Possible cause

- Check to make sure both devices are paired and connected over Bluetooth.

- Restart the BTH20 to auto-connect with your Bluetooth device.

- Make sure the BTH20 is fully charged.

- Check to make sure both devices are paired and connected over Bluetooth.

- Restart the BTH20 to auto-connect with your Bluetooth device.

- Press play to resume music.

- Check and make sure your mobile device supports Bluetooth A2DP proﬁle.

Page 10 Page 11

Page 7

Warranty Information

Concept 101 LLC does not warrant that the unit will work properly in all environmental conditions, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or ﬁtness for a particular purpose other than the purpose identiﬁed within this user’s manual. Concept 101 LLC has made every effort to ensure that this user’s manual is accurate, and disclaims liability for any inaccuracies or omissions that may have occurred. Information in this user’s manual is subject to change without notice and does not represent a commitment on the part of Concept 101 LLC. Concept 101 LLC reserves the right to make improvements to this user’s manual and/or to the products described in this user’s manual, at any time without notice. If you ﬁnd information in this manual that is incorrect, misleading, or incomplete, please contact us through our website.

Speciﬁcations

- Bluetooth 4.0

- Bluetooth compatibility: Bluetooth 2.0 or above device with A2DP/AVRCP/HFP/HSP

- Working distance: Up to 30 ft

- Frequency response: 2.4 ~ 2.4835 GHz

- Charging time: 2 to 3 hours

purchase date:

place of purchase:

Warranty Information

Limited Warranty

The AT&T brands are used under license. Any repair, replacement, or warranty service, and all questions about this product should be directed to Concept 101 LLC at www.att.com/electronics or call 1 (888) 920-8680 from the USA or Canada. Concept 101 LLC warrants to the original purchaser that the product will be free from defects in material, parts and workmanship for the period designated for this product. The warranty commences the day the product is purchased and covers up to a period of one (1) year (90 day Labor and 1 year Parts). Concept 101 LLC agrees that it will, at its option, replace the defective product with either a new or remanufactured unit equivalent to your original purchase during the warranty period. Should the Parts warranty period exceed the Labor warranty period, Concept 101 LLC will supply at no charge for the remainder of the Parts warranty, any new or remanufactured replacement parts as required by the product. During this period all labor and service charges will become the responsibility of the customer.

Exclusions: This warranty does not apply to the appearance or exterior of the product

which may have been damaged or defaced, altered or modiﬁed in design or construction. This warranty does not apply if the serial number is altered or removed, or if there is any damage due to power line surge, user damage to the AC power cord, connection to improper voltage source, general misuse, accidents, or repair attempts by unauthorized service agents. Other exclusions include ear pads, rechargeable and non-rechargeable batteries.

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CUSTOMER; CONCEPT 101 LLC SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ANY IMPLIED WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE DURATION OF THE WARRANTY.

Some states do not allow the exclusion or limitations of incidental or consequential damages, or limitations on how long the warranty lasts. In these cases the above exclusions or limitations may not apply to you. This warranty gives you speciﬁc legal rights and you may also have other rights which vary from state to state.

Obtaining Service: To obtain service, product literature, supplies or accessories

please call 1 888-920-8680, or visit our website, www.att.com/ electronics, to create a ticket for exchange/repair. Please make sure to provide the date of purchase, model number and a brief description of the problem. Our customer service representative will contact you or send detailed return instructions.

Page 12 Page 13

Page 8

www.att.com/electronics