Atlantic Technology In-Wall Loudspeakers User Manual

Atlantic Technology Innovations for In-Wall Loudspeakers

Low-Resonance Tweeter (LRT™) and Directional Vector Control (DVC™)

It is obvious that people choose in-walls
because they don’t want to see speaker
boxes in their room. Furthermore, most
people mount in-walls high off the floor—
above the sight line—again, because
people don’t want to see the speakers. The
result of this is that much of the sound is
focused above the listener's head and
distorted in terms of the frequency
response balance of the sound reaching
the listener's ears.

Previous attempts to compensate for this
non-optimal positioning have used some
variant of the “pivoting tweeter” approach.
But pivoting tweeters don’t work very well.
Here’s why: two-way tweeters cross over
too high in frequency—about 3,500-4,000
Hz—so it is the woofer, not the tweeter,
that plays most of the midrange, and it’s
the midrange that your ear uses to
determine directionality.

Woofers beam badly in the upper
midrange. If the woofer is above ear level,
it’s going to beam the upper midrange like

a flashlight right over the listener’s head.
The so-called “pivoting tweeter” is not
much help, because it doesn’t play the
midrange! And to make matters worse,
when you pivot a tweeter, you introduce a
ledge or shelf that diffracts the tweeter's
output and smears the propagation of the
treble frequencies.
It’s a messy,
inelegant solution
that probably does
more harm than
good.

So here’s what we
did instead: We
modified our
tweeter so it can
play lower
frequencies; far
down into the midrange, about a full octave
lower than a conventional tweeter to
around 2,000 Hz. It’s a very highly­engineered tweeter system with a vented
backplate, playing into its own sub­enclosure (complete with internal stuffing!),
and special heat-sinking. We call it the
Low-Resonance Tweeter (LRT™). Now the
woofer doesn’t have to struggle to reach
into the upper midrange, and we get a
much smoother blend of radiation
coverage angles as we transition from the
woofer to the tweeter.

One of the characteristics of speaker
performance is what engineers call
“lobing.” A speaker’s output will lobe up or
down, depending on things like crossover
topology, driver positioning, etc. It can be
very frustrating to develop, say, a new 35­inch tall floor-standing speaker and find

343 Vanderbilt Ave Norwood, MA 02062 PH 781-762-6300 Fax [phone] www.atlantictechnology.com

that its smoothest response was 15
degrees down from straight ahead (aimed
right at the listener’s knees!), all because
you didn’t pay proper attention to lobing
behavior.

We all know that speakers lobe. So why
not take advantage of that fact instead of
fighting it? That’s what our exclusive
Directional Vector Control (DVC™) does.

By flipping the DVC switch to “on,” we
electronically manipulate the crossover so
that the speaker’s midrange output lobes
down about 15 degrees from the speaker.
This is perfect for when this speaker is
mounted above ear level and you want to

use them for front-channel LCR duty. The
midrange sounds—which determine
directionality and intelligibility—are directed
down at the seated listeners’ ears, even
though the speakers are six or seven feet
above the floor. The following graph shows
the measured response of this speaker at
the listening position; red is DVC off, blue
is DVC on.

Therefore, between the low crossover point
of LRT and the up-down midrange lobing
of the DVC, we’ve engineered a speaker
that covers the listening area more
effectively, without the drawbacks and
compromises of ordinary high-crossover
pivoting tweeters, and without having to
resort to the expense of a three-way
design.

We’ve also included a Boundary control to
compensate for the upper bass/lower
midrange buildup that occurs when a
speaker is mounted near a ceiling or wall
boundary, and there’s a three-position HF
level control to adjust tweeter level for
varying room acoustics.

_____________________________________

Steve Feinstein
Director of Marketing and Product Development
Atlantic Technology

343 Vanderbilt Ave Norwood, MA 02062 PH 781-762-6300 Fax [phone] www.atlantictechnology.com