Atec V7x Series User Manual

V7X Series - Hipot Testers
With color touch LCD & high speed DSP technology, the compact & rugged V7X sets
the standard for price/performance ratio. Made in the USA to meet tough
UL, CSA, TUV and IEC Hipot requirements - the V7X provides unbeatable speed,
accuracy, user safety and reliability.
Choose from six low cost models offering AC & DC Hipot to 5KV, leakage current
measurement to 100 nano-amps, Insulation Resistance to 450GΩ and Ground Bond to 30
amps. Combine all that with USB, RS232 and Digital I/O interfaces, plus a 2 year warranty.
The V7X is simply unbeatable
Vitrek V7X Series Performance Specifications
AC Hipot
Output Voltage 10 to 5000V 50 or 60 Hz
Accuracy : 1.4% of setting +0.1% Full Scale, No load to full load Resolution : 1V at all levels Max load current : 20mArms Leakage Current Min/Max Limits during dwell of none, or up to 20mArms
Accuracy : 1.5% of reading +5uA Resolution : 1uA
DC Hipot
Output Voltage 20 to 5000V test voltage
Accuracy : 1.4% of setting+0.1% Full Scale, No load to full load Resolution : 1V at all levels Max load current : 10mA Leakage Current Accuracy : 1.5%+1uA Resolution : 0.1uA
IR - Insulation Resistance
Test Voltage 20 to 5000VDC
Accuracy : 5%+5V No load to full load
Resolution : 1V at all levels Max Charge Current: 5mA automatic Max Capacitive Load: 2uF Resistance Max IR: 450Gigohm (90M per volt) Min IR: 150K Accuracy : 2% (rdg <5% of max IR), 5% (< 15% of max IR), 10% (< 30% of max IR), 20% (above
30% of max IR)
Max Resolution : 0.1% of value
Min/Max Limits : Defined for each step, max may be set to none Test Completion Stop on Time: Determination on final reading Stop on Pass: Test terminates with PASS for any reading within limits Stop on Fail: Test terminates with FAIL for any reading outside limits Stop on Steady: Test terminates with PASS for any reading within limits which is
Low Resistance
Resistance Range: 0ohm to 60Kohm
Accuracy : 1.4 %+0.02 (<10), 3%+1ohm (<1K), 10 % above 1K
Resolution : Down to 0.001 Min/Max Limits : Defined for each step, each may be set to none Test Method 2 terminal measurement , 10.5mA max, 4.15V max Resistance Offset Test leads/fixture measurement offset may be universally applied
Ground Bond
Test Current 1 to 30Arms (42A pk), 50/60Hz
Accuracy : 2.5%+10mA
V70
V71
V73
V74
V79
AC Hipot
DC Hipot
● ● ●
IR ● ● Ground Bond
● ●
Low Resistance
Resolution : settable to 0.01A at all levels Compliance: > 4.5Vrms (6V pk) for all currents Method 4 terminal measurement Resistance Max Resistance: Up to compliance V limit at defined test current (4.5ohms max) Min/Max Limits : Defined for each step, min may be set to none Accuracy : 2.5%+3m (<2A), 2m (<6.5A), 1m (otherwise)
Resolution : 0.1m (>6.5A), 1m (otherwise) Resistance Offset Test leads/fixture measurement offset may be universally applied
Test Timing
Ramp Time For AC/DC Hipot: 0 to 99.9sec (0.1sec resolution, 0.05sec accuracy) Test/Dwell Time 0.1 to 9999sec or user end (0.1sec resolution, 0.15sec accuracy) Ramp Down May be set to 0sec or same as Ramp time, automatically skipped if no failure and next step
is same AC/DC or IR test type Shutdown Breakdown : within 150us
HV Safety : within 1ms
User Stop or Interlock opened : within 2ms
Resistance/Current Limit : within 100ms
Test Functions
Breakdown For Hipot tests, automatically checks for sudden uncontrolled increases of load current
throughout test, no min/max leakage required Arc Detect For Hipot tests, settable to none or adjustable level between 1 and 30mApk, 5MHz
bandwidth Pause Step A timed pause of defined length between 0.1s and 999.9s. Hold Step A user continued hold step with a 2 line message to be displayed to the user while the step
is executing. Switch Step Provides control of up to 4 Vitrek 964 switch units, each SWITCH step allows complete
control over the states of all switches Test Memory Up to 999 total test steps may be defined in up to 60 different sequences
General Specifications
DSP Measurement 40,000 samples per second for output control and parameter measurement
Display 4.3" 480 x 272 Color touch LCD user interface Interfaces USB 2.0, RS232 & Contact closure digital I/O with safety interlock
Warranty 2 year parts and labor
Accessories Alligator test leads for hipot & continuity units (TL-209), 4-wire alligator test leads for GB
Item
Description
Price
V70
AC Hipot Tester
V71
AC/DC Hipot Tester
V73
AC/DC/IR Hipot Tester
V74
AC/DC/IR/GB Hipot Tester
V79
Ground Bond Tester
QTV Pro 7
QuickTest Software
TL-209
Additional HV/Continuity Test Lead set
K-2R
Additional Ground Bond Lead Set
HVL-7
High Voltage Warning Light
units (K-2R), operator's manual CD, QT Pro V utility software and evaluation version test
automation software & power cord
Calibration 2 year accuracy specifications and recommended calibration interval, ANSI/NCSL Z540 NIST
Traceable cal cert with data standard
Safety CE mark certified to EN61010
Power 115/230VAC ±10% internally selectable, 50-60Hz, 200VA max
Dimensions 5.25" (133mm) H x 9.5" (240mm) W x 11" (280mm) D
Weight 12 lbs, 5.5kg net (V70-73), 16 lbs, 7.3kg net (V74 & V79)
Country of Origin Made in the USA
Ordering Information
Vitrek Corporation
12169 Kirkham Rd, Poway, CA 92064, 858.689.2755 www.vitrek.com
11-01-2012 Prices and specifications subject to change
Loading...