Atec UCS200N User Manual

KARTA KATALOGOWA > UCS 200N-series > 20120209
UCS 200N SERIES
ULTRA COMPACT SIMULATORS FOR AUTOMOTIVE TRANSIENTS
DO BADAŃ ZGODNIE Z ...
> Audi (Reference vehicles) > BMW - (Airbag ECU) > BMW 600 13.0 (Part 2) > BMW GS 95002 (1999) > BMW GS 95002 (2001) > BMW GS 95024-2-1 (2010-01) > Case New Holland ENS0310 > Chrysler CS-11809 (2009) > Chrylser CS-11979 > Chrysler DC-11224 Rev.A > Chrysler PF-9326 > Claas CN 05 0215 > Cummins 14269 (982022-026) > DaimlerChrysler DC-10614 > DaimlerChrysler PF-10540 > EN 300329 > EN 300340 > EN 300342-1 > EN 301489-1 > EN 301489-17 > EN 301489-24 > ...
ULTRA-COMPACT SIMULATORS FOR AUTOMOTIVE TRANSIENTS FOR PULSES 1, 2 AND 3A/3B
The UCS 200N Ultra-Compact Simulator series for Automotive Transients unifies the capabilites of an EFT/Burst simualtor, a Micropulse simulator and the required coupling network into one box. The UCS 200N series is equiped to meet all international and car manufacturer specifications from around the globe. The built-in coupling network ranges up to 200A depending on the model. The built-in coupling network can be used and controlled by any unit of the LD 200N series, VDS 200N series and PFS 200N series. For tests beyond standard's requirements the waveform parameters of the Micropulse generator can be varied in a wide range by means of the FreeStyle mode.
HIGHLIGHTS
> Built-in EFT/Burst generator module
OBSZARY ZASTOSOWAŃ
AUTOMOTIVE
> Built-in Micropulse generator module (ISO 7637,
JASO, SAE and NISSAN)
TELECOM
> Built-in coupling network 60V, up to 200A > Built-in battery switch > Overcurrent protection > USB and GPIB-Bus
www.emtest.com © EM TEST > STRONA 1/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
PARAMETRY TECHNICZNE
BENEFITS
SMARTEST SOLUTION FOR AUTOMOTIVE TRANSIENT TESTING
Never before an Ultra-Compact Simulator for automotive transient testing like the UCS 200N series was available. All international standards and most car manufacturer requirements have been put into one box. All pulses are fully compliant to the specifications. Even more, the waveform parameters for micropulses can be varied in order to test with pulses beyond any standard specification. The UCS 200N series is the heart of the redesigned EM TEST Automotive test set-up having the ability to control any external EM TEST Load Dump and Battery Supply simulator. The built-in coupling network for nominal DC currents of up to 200A forms the single-port DUT connection for fully automated tests. The software iso.control with its extensive standards library put this test equipment to the top with almost unlimited test capabilities.
SOFTWARE
ISO.CONTROL SOFTWARE FOR CONTROL AND DOCUMENTATION
Outstanding user convenience, clearly structured windows and operation features and the EM TEST standards library along with the flexibility to generate user specific test sequences very easily are the main features of iso.control software. The software is automatically configured according to the connected EM TEST generators. iso.control software covers international/national standards and most of the manufacturer standards and is continuously updated. Extensive reporting capabilities help the user to create test reports that meet international requirements. iso.control is supported by Windows 2000, Windows XP, Windows Vista and Windows 7. Remote control is achieved either via USB or GPIB. iso.control supports a wide range of GPIB cards of National Instruments.
ACCESSORIES
OPERATION
EASY TO OPERATE
Front panel menu and function keys enable the user to program his test routines quickly and accurately. The cursor allows fast control of all test parameters of the programmed routine, thus test procedures are simplified and confidence is generated that every step is carried out correctly.
ACC - CAPACITIVE COUPLING CLAMP
All lines other than supply lines are subjected to electrical fast transient pulses by means of the ACC complying to ISO 7637-3:2007
CA EFT KIT - VERIFICATION KIT FOR EFT/BURST PULSES
As per ISO 7637-2:2011 the characteristic of the burst generator needs to be verified with two different loads 50 ohm and 1,000 ohm. EM TEST offers a calibration kit consisting of the two loads and an adapter to verify the pulses.
CA ISO - LOAD RESISTORS FOR PULSE VERIFICATION
A set of highly-accurate load resistors is unified in a single box for the verification of micropulses and Load Dump pulses as specified in ISO 7637-2:2011, Annex C and a wide range of manufacturer specifications.
www.emtest.com © EM TEST > STRONA 2/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
PARAMETRY TECHNICZNE
UCS 200N SERIES
UCS 200N MODELS
UCS 200N50 Built-in coupling/decoupling
network, 60V/50A, 100A@500ms
UCS 200N100 Built-in coupling/decoupling
network, 60V/100A, 150A@500ms
UCS 200N150 Built-in coupling/decoupling
network, 60V/150A
UCS 200N200 Built-in coupling/decoupling
network, 60V/200A
INPUT
DUT supply +/- DC voltage from VDS 200N or
any other DC supply
Pulse 5, 7 From one LD 200N
OUTPUT
DUT supply +/- Central DUT output Coaxial output
port
To connect the capacitive coupling clamp as per ISO 7637-3:2007
ELECTRICAL FAST TRANSIENTS
EFT/BURST MODULE FOR TEST PULSES 3A/3B
As per ISO 7637-2 Test voltage 25V - 1,000V ± 10% Rise time 5ns ± 1.5ns Pulse duration 150ns ± 45ns Verification As per Annex C of ISO 7637-2:2011
into 50ohm and 1,000ohm load Source impedance Zq = 50ohm Polarity Positive/negative (Pulse 3b/3a)
TRIGGER CIRCUIT
Trigger of bursts Automatic, manual, external Burst duration T4 = 0.1ms - 999.9ms Repetition rate T5 = 10ms - 9,999ms Spike frequency f = 0.1kHz - 200kHz Test duration T = 0:01min - 999:59min
T > 999:59min --> endless
OUTPUTS
Direct Via 50ohm-coaxial connector
(for tests using e.g. a capacitive
coupling clamp) Coupling mode To the + battery line (supply lines) CRO trigger 5V trigger signal for oscilloscope
TEST ROUTINES
Quick Start On-line adjustable parameters,
easy-to-use Standard Test
routines User Test routines Random burst release
As per ISO 7637-2:2011, Levels 1 - 4
Change voltage after T
Change frequency after T
www.emtest.com © EM TEST > STRONA 3/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
PARAMETRY TECHNICZNE
MICROPULSES
MICROPULSE MODULE FOR TEST PULSES 1, 2A AND 6
As per ISO 7637-2:2011
Test voltage U = 20V - 600V ± 10%
(peak voltage and polarity as per selected standard)
Repetition rate 0.2s - 99.0s
ISO PULSE 1 (12V)
Rise time 1us +0%/-50% (10% - 90%) Pulse duration 2ms ± 10% (10% - 10%) Int. resistor 10ohm ± 10%
ISO PULSE 1 (24V)
Rise time 3us +0%/-50% (10% - 90%) Pulse duration 1ms ± 10% (10% - 10%) Int. resistor 50ohm ± 10%
ISO PULSE 2 (12V/24V)
Rise time 1us +0%/-50% (10% - 90%)
MICROPULSES
TRIGGER
Automatic Automatic release of the pulses Manual Manual release of a single pulse External External release of a single pulse Battery switch Off time, selectable; 0 - 10,000ms
OUTPUT
DUT supply +/- Central DUT output Coupling To the battery +line Decoupling Via diode and battery supply switch
TEST ROUTINES
Quick Start Immediate start; easy to use and fast User Test routines 1. Custom made test routines
2. Change voltage after n pulses
Standard Test routines
Service Service, setup, self test
As per ISO 7637, SAE J1113, JASO
and manufacturer specifications
Pulse duration 50us ± 10% (10% - 10%) Int. resistor 2ohm ± 10%
ISO PULSE 6 (12V) AS PER ISO 7637-1:1990
Rise time 60us +0%/-50% (10% - 90%) Pulse duration 300us ± 10% (10% - 10%) Int. resistor 30ohm ± 10%
AS PER ISO 7637-2 THE FOLLOWING STANDARDS CAN BE COVERED
SAE J1113 GM 3097 BMW Volkswagen PSA Chrysler PF 9326 DC 10614 Renault FIAT Mitsubishi Honda Ford ES-XW7T
www.emtest.com © EM TEST > STRONA 4/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
PARAMETRY TECHNICZNE
MICROPULSES AS PER MANUFACTURER STANDARDS
JASO D-001, PULSE A2
Test voltage +110V Capacitor C = 4.7uF Pulse duration 2.5us ± 30% at tau(36.8%) R1 0.6ohm ± 10% R2 0.4ohm ± 10% Polarity Positive
JASO D-001, PULSE B2
Test voltage -260V Capacitor C = 33uF Pulse duration 2.0ms ± 20% at tau(36,8%) R1 60ohm ± 10% R2 80ohm ± 10% Polarity Negative
MICROPULSES AS PER MANUFACTURER STANDARDS
NISSAN 28400 NDS 07, PULSE C50
Test voltage ±300V ± 10% Capacitor C = 33uF R1 30ohm ± 10% R2 200ohm ± 10% Polarity Positive and negative
NISSAN 28400 NDS 07, PULSE C300
Test voltage -300V ± 10% Capacitor C = 33uF R1 100ohm ± 10% R2 75ohm ± 10% Polarity Negative
SAE J1455 | MUTUAL PULSE
Rise time 1us ± 20% (10% - 90%)
JASO D-001, PULSE D2
Test voltage +170V Capacitor C = 2.2uF Pulse duration 2.5us ± 30% at tau(36,8%) R1 1.2ohm ± 10% R2 0.9ohm ± 10% Polarity Positive
NISSAN 28400 NDS 03, PULSE B2
Test voltage -300V ± 10% Capacitor C = 33uF R1 100ohm ± 10% R2 75ohm ± 10% Polarity Negative
NISSAN 28400 NDS 07, PULSE C8
Test voltage ±300V ± 10% Capacitor C = 1uF
Pulse duration 15µs ± 20% at tau(36.8%) Int. resistor 50ohm ± 10%
SAE J1455 | INDUCTIVE PULSE
Rise time 1us ± 20% (10 - 90%) Pulse duration 1,000us ± 20% at tau(36.8%) Int. resistor 20ohm ± 10%
FREESTYLE MODE MICROPULSES
PULSE PROGRAMMING MODE
Rise time 1us - 10us in steps of 1us Pulse duration 50us - 10,000us Int. resistor 2ohm - 100ohm in steps of 5ohm;
200ohm, 400ohm and 450ohm
R1 500ohm ± 10% R2 450ohm ± 10% Polarity Positive and negative
www.emtest.com © EM TEST > STRONA 5/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
PARAMETRY TECHNICZNE
GENERAL DATA
DIMENSIONS AND WEIGHT
UCS 200N50 19"/3HU, approx. 20kg UCS 200N100 19"/6HU, approx. 30kg UCS 200N150 19"/9HU, approx. 35kg UCS 200N200 19"/9HU, approx. 35kg Supply voltage 115/230V +10/-15% Fuses 2 x T 2AT (230V) or 2 x T 4AT (115V)
INTERFACE
Serial interface USB Parallel interface IEEE 488, addresses 1 - 30 CN interface To control the internal CN and
battery switch
OPTIONS
ACC Capacitive coupling clamp KW50 100:1 divider, 50ohm KW1000 400:1 divider, 1,000ohm CA EFT kit EFT/Burst verification kit A6dB 6dB attenuator, 50ohm CA ISO Load resistors for the verification of
micropulses and Load Dump pulses
iso.control Software to control the test,
including standard library, test report facility and data conversion generator.
www.emtest.com © EM TEST > STRONA 6/7
KARTA KATALOGOWA > UCS 200N-series > 20120209
KOMPETENTNI, GDZIEKOLWIEK BYŚ BYŁ
BEZPOŚREDNI KONTAKT Z EM TEST
Szwajcaria
EM TEST (Switzerland) GmbH > Sternenhofstraße 15 > 4153 Reinach > Switzerland Telefon +41 (0)61/7179191 > Fax +41 (0)61/7179199 Internet: www.emtest.ch > E-mail: sales@emtest.ch
Niemcy
EM TEST GmbH > Lünener Straße 211 > 59174 Kamen > Deutschland Telefon +49 (0)2307/26070-0 > Fax +49 (0)2307/17050 Internet: www.emtest.com > E-mail: info@emtest.de
Francja
EM TEST FRANCE > Le Trident - Parc des Collines > Immeuble B1 - Etage 3 > 36, rue Paul Cézanne > 68200 Mulhouse > France Telefon +33 (0)389 31 23 50 > Fax +33 (0)389 31 23 55 Internet: www.emtest.fr > E-mail: info@emtest.fr
Polska
EM TEST Polska > ul. Ogrodowa 31/35, 00-893 Warszawa > Polska Telefon +48 (0)518 64 35 12 Internet: www.emtest.com/pl > E-mail: info.polska@emtest.de
Wszystkie informacje dotyczące dostaw, wyglądu zewnętrznego i danych technicznych opisujących aktualny stan wraz z datą publikacji mogą ulec zmianie bez wcześniejszych informacji.
USA / Kanada
EM TEST USA Inc. > 9250 Brown Deer Road > San Diego > CA 92121 Telefon +1 (858) 699 1685 > Fax +1 (858) 458 0267 Internet: www.emtest.com > E-mail: tom.revesz@ametek.com
Chiny
EM TEST Representative Office Beijing > Rm 913, Leftbank > No. 68 Bei Si Huan Xi Lu > Haidian District > Beijing 100080 > P.R. China Telefon +86 (0)10 82 67 60 27 > Fax +86 (0)10 82 67 62 38 Internet: www.emtest.com > E-mail: emtestbj@public.bta.net.cn
Malezja
EM TEST (M) SDN BHD > Unit B2-6, Jalan Dataran SD2 > Dataran SD2, PJU9 > Bandar Sri Damansara > 52200 Kuala Lumpur > Malaysia Telefon +60 (03)62 73 22 01 > Fax +60 (03)62 74 22 01 Internet: www.emtest.com > E-mail: sales@emtest.com.my
www.emtest.com © EM TEST > STRONA 7/7
Loading...