Atec TP04310A User Manual

TP04310A

Mobile Temperature System for testing components, hybrids, parts, modules, subassemblies and printed circuit boards at precise temperature

TEMPERATURE PERFORMANCE AND AIRFLOW CAPACITY

Model TP04310A ThermoStream

Temperature Range:

Typical Temperature Transition Rate (air)

System air flow output

Temperature accuracy 1.0°C (when calibrated against NIST transfer standard)

Temperature set, display and resolution ± 0.1°C

1,3

1,2

-80

° to +225°C (60 Hz System)

-75° to +225°C (50 Hz System)

-55° to +125°C: approximately 10 seconds or less +125

° to -55°C: approximately 10 seconds or less

2.4 to 9 liters/second (5 to 18 scfm) CONTINUOUS

Temperature Control:

DUT Sensor Ports Type T and Type K Thermocouple ports standard

DUT Control Control to within ± 0.1°C; SELF-TUNING available in DUT Control

Remote interface ports IEEE-488, RS232C Serial, and Start Test/End of Test/Stop

on First Fail (ST/ET/SFF)

Note: Ultimate low temperature and system performance may vary under operating conditions less than or greater than nominal.

Note: Transition performed under nominal operating conditions.

Note: Low temperature extremes can be achieved at reduced airflow rates.

USER FEATURES

Modes of Operation Two: Manual and Program Modes

Test set-up configurations 12 Manual Mode test programs and 12 Program Mode

test programs may be created

Test set-up storage 11 Manual Mode test programs, 11 Program Mode

Ramp/soak/cycle configurations

DUT temperature control Patented4Dual Loop Temperature Control

Status indicators Real-time status displayed on-screen and via remote

Purge flow tester interface Dry air purge protects tester electronics protection from condensation

Purge flow capacity 0.25 to 1.5 liters per second (0.5 to 3 scfm) airflow

Calibration Automated, simplified and accurate for all airflows

Thermal head raising and lowering Pneumatic control on thermal head,

Head positioner movement

Manipulator (ar

m) movement

test programs and 11 affiliated “Define Parameters” test set-ups can be stored for later recall.

In Program Mode, up to 12 sequences per test set-up; table is displayed on-scr

interface

and DUT types

operated manually or via remote interface

Manual locking (4 locks), 360 can be manually pivoted, turned, tilted and vertically swung for ease of interface at tester site.

Motorized raising and lowering of arm; 330° positioning range around the base unit

een

head rotation; head

System Specifications

Part No. SL10290 R/C

Note: US Patent no. 4,734,872

Model TP04310A ThermoStream

System Specifications

ENVIRONMENTAL AND SAFETY FEATURES

Over-Temperature Protection +235°C (factory-set) (Also uses user-settable high and low air temperature limit)

Mobility 4 swivel caster wheels with locks (10.16 cm (4 inch) diameter, static dissipative);

rear handle for ease of transport

Refrigerants HCFC-free and CFC-free, non-toxic, non-flammable

Noise level <65 dBA approximately

Serviceability Field-replacement modules and printed circuit boards

Weights and Dimensions Base: Width: 61.0 cm (24 in.) Depth: 71.1 cm (28 in.); Height: 108 cm (42.5 in.);

System weight: 236 kg (520 lbs); Packed: 365 kg (805 lbs)

Maximum operating height 130.3 cm (51.25 in.) approximately

Minimum operating height 69.9 cm (27.5 in.) approximately

(An additional 20.3 cm (8 in.) rear clearance is required for supply connections and cabinet ventilation.)

ISO 9001-2000 Certified

FACILITY REQUIREMENTS

Power Requirements

ompressed Air Requirements

Clean, Dr

Supply Pressure 6.2 to 7.6 BAR (90 to 110 PSIG)

Supply flow at minimum supply pressure (Nominal 25 scfm)

Air supply temperatur

Operating T

Humidity

Note: System is configured for operation within voltages listed above using an internal transformer.

Please specify power configuration with order.

Under operating conditions which are less or greater than nominal, performance may be less

than specification provided.

y Air

emperature +20º to +28ºC (+23ºC nominal)

200-250 VAC (230V nominal), 50 Hz, 30 amp, 1 phase 200-250 V 60 Hz, 30 amp, 1 phase

Filter Oil content: <0.01 ppm by weight filtered

Dewpoint: <10ºC @ 6.2 BAR (90PSI)

7.2 l/s to 14.3 l/s (15 to 30 scfm)

+20º to +25ºC (+22ºC nominal)

0 to 60% (45% nominal)

AC (230V nominal),

ed to 5 micron particulate contamination

to .01 micron oil contaminant

4 Commercial Street Sharon, MA 02067 USA Tel: (781) 688-2300

ax: (781) 688-2301

F www.temptronic.com

ws® is a registered trademark of

Windo Microsoft Corporation.

ThermoStream® and ThermoFixture® are registered trademarks of Corporation.

tion. These specifications are valid for

Corpora the standard product and are subject to change without notice. Applications requiring modification of electrical, should be discussed with the factor accommodation at an additional cost. Printed in USA.

art No.

thermal or mechanical characteristics

SL10290 R/C 3/2005

Temptronic

y for possible