Atec TP04100A User Manual

TP04100A

Temperature Range

emperature Display and Resolution 0.1°C

Temperature Accuracy ±1°C

Facilities Preparation

Power Requirements

Compressed Air Supply Pressure

Supply Airflow at 4 to 5 liters/second (8-10 scfm) Nominal Supply Pressure

Dewpoint

Air Supply Temperature +20° to +28°C (+22°C nominal1)

Operating Temperature (Ambient) +20° to +28°C (+22°C nominal1)

Humidity 0 to 60% (45% nominal1)

Noise Level ≤

Power Connection Standard male IEC320 power connector socket for

Reduced performance may be encountered at operating conditions less than or greater than nominal.

Requires clean, dry air supply.3-40°C dewpoint is nominal for low temperature testing for extended periods.

115V AC ±10%, 50 or 60 Hz, 1 ø, 15 amp 230V AC

5.6 to 7 kg /cm2(80 to 90 PSIG),

5.6 kg/cm2(80 PSIG) nominal

4.5 l/s (9 scfm) nominal

ambient to -40°C

attachment of IEC320 power cord (meets IEC requirements). Power cord (2.4 meters in length) included.

-20° to +225°C

(When calibrated against

NIST Transfer Standard)

±10%, 50 or 60 Hz, 1 ø, 10 amp

70 dBA

Model TP04100A ThermoStream

Dimensions and Weight

Dimensions: Controller: 40.1 cm (15.8 inches) wide x 14.8 cm (5.8 inches) high x 48.9 cm (19.2 inches) deep

Thermal Wand: 8 cm (3 inches) in diameter x 36 cm (14 inches) long

Stand: 48.25 cm (19 inches) approximately above tabletop to top of post

Reach from vertical post: Standard: 51 cm (20 inches)

Weight: Controller with Thermal Wand and Hose ................................................. 14.5 kg (32 lbs)

and Stand Assembly ................................................................ 7 kg (15.5 lbs)

mal W

Ther

Thermal Cap ........................................................................................... .45 kg (1 lb)

Options and Accessories

Ther

mal Wand Stand Assembly Expanding, locking stand assembly rotates 340° about the controller cabinet for

positioning the Thermal Wand directly over the DUT.

Benchmount Stand Assembly Attaches the Thermal Wand Stand Assembly directly to a bench. Can be mounted up to

30.5 cm (12 inches) from controller chassis.

Thermal Cap Transparent single wall glass cap of approximately 9.9 cm (3.9 inches)

ID (Internal Diameter); includes metal guard.

oud Kit

Shr

Insulation Kit

Custom Thermal Test Enclosures Frost-free thermal enclosures for testing ICs, hybrids, modules and small subassemblies and Ther

Pneumatic Wand Lift Assembly Automates the raising and lowering of the Thermal Wand for the loading and unloading of

moFixtur

Shroud attaches to thermal wand for coupling to devices. Kit contains a variety of sizes and shapes (See price list). Available in conductive and non-conductive material.

Non-conductive silicone foam r

ee sheets: (12” x 12” x .125”), (12” x 12” x .25”), (12” x 12” x .5”)

Thr

ecise temperatur

pr custom configurations. ThermoFixture can include ATE interface.

the DUT.

e in a moistur

ubber sheets.

ee ther

e-fr

mal envir

onment. Available in standard and

System Specifications

an inTEST Company

TEMPTRONIC

Options and Accessories

The Thermal Wand may be operated in-hand or secured in the optional Thermal Wand Stand Assembly for added stability and hands-free operation. Mounted directly to the TP04100A controller cabinet, the Stand Assembly rotates over 340°, and expands and locks for stable, proper coupling of the Thermal Wand to the DUT. The optional Benchmount Stand Assembly attaches to the bench to hold the Thermal Wand Stand Assembly. The Thermal Wand may then be used while secured in the stand for stability during test while located conveniently at the bench.

To protect from moisture condensation and frost at the DUT site, the optional single-wall glass the Thermal Wand with the shrouds. The Thermal Cap is approximately 9.9 cm (3.9 inches) ID and includes a metal guard. Additional conductive and non-conductive sheets and shrouds in various sizes and shapes are also optional.

For frost-free thermal testing of ICs, hybrids, modules and small subassemblies in a precisely controlled thermal environment,

ThermoFixture®and Custom Thermal Test Enclosures are available. ThermoFixture enclosures include the complete ATE tester

interface and DUT thermal control for moisture-free testing at low temperatures even over longer test periods.

Thermal Cap may be attached to

Custom Thermal Test Enclosure

4 Commercial Street Sharon, MA 02067 USA Tel: (781) 688-2300

ax: (781) 688-2301

F www.temptronic.com

oduct and ar

These specifications ar or mechanical characteristics should be discussed with the factory for possible accommodation at additional cost. Printed in U.S.A. ThermoStream®and ThermoFixture®are registered trademarks of Temptronic Corporation. Windows®, Windows 95®and Windows NT®are registered trademarks of Microsoft Corporation

e valid for the standar

. LABVIEW®is a registered trademark of National Instruments, Inc. 3/2005 Part No. SL10260R/C

d pr

e subject to change without notice. Applications r

equiring modification of electrical, ther

ISO 9001-2000 Certified

mal