Atec Sentry50-Plus User Manual

50 Plus Ground Bond Tester

USES:

The Sentry 50 Plus Ground Bond Tester provides up to 30A for high current

testing to even the most stringent standards. The front panel of the Sentry

instrument includes a digital display and user friendly control allowing test

User programmable output current, 3A to 30A AC

in 0.01A steps, provides extensive coverage for testing to UL, CSA, VDE, IEC

Limit the voltage to the DUT using the pro

grammable source voltage from 1.0V to 8.0V rms and meet the low voltage

requirement of CSA 22.2 No. 0.4 Bonding and Grounding of Electrical

A resistance measurement

, plus user programmable high and low resistance

limits with Pass/Fail indication, make this tester ideal for production Go/NoGo

Incorporate the Sentry 50 Plus unit into an automated man

ufacturing environment with remote start and Go/NoGo results output through

The Sentry 50 Plus can be used alone or connected to

the Sentry Plus 10, 20 or 30 Hipot Testers for complete product electrical safe

ty testing with the push of one button. When the Sentry 50 Plus has complet

ed a continuity test, with pass indication, it can remotely start the Sentry Plus

Front panel display of an operator

1-800-253-1230

Fax 1-978-461-4295

Intl. 1-978-461-2100

For more information

about special purchase,

rent & lease options,

call

For more detailed

specifications, visit

www.quadtech.com

Sentry

• Production Testing of Instruments and Appliances

• Testing of Information Technology Equipment, Medical Instrumentation, and other Electrical Products with 3-prong Power Cords

• Electrical Safety Testing of Motors, Generators, and Transformers

• Low Resistance Testing of Electrical Connections

FEATURES:

• Programmable Output Current from 3A to 30A AC

• Programmable Source Voltage from 1.0 to 8.0V rms

High Current Testing To 30 Amps

Introduction

parameters and limits to be set easily without the high current activated.

Description

Wide Test Current Range:

and other agency safety requirements.

Programmable Source Voltage:

Equipment (4V, 30A, 100m Ω limit, 2-minute test) plus many others.

Programmable High and Low Resistance Limits:

range from 0.1mΩto 510m Ω

testing.

Remote Control:

• Resistance Measurements from

0.1mΩ to 510mΩ

• Programmable High and Low Limits

• Programmable Test Time

• Storage of 99 Tests Setups with Multiple Steps per Measurement

• Remote I/O Interface

• Graphic LCD

• Front Panel Lockout

• 4-Terminal Kelvin Connection

• Built-in Calibration Software

• Compatible with Sentry & Guardian Series Hipot Testers

the rear panel PLC interface.

Hipot Compatibility:

Series instrument for a hipot test in sequence.

Built-in Calibration via Software:

prompted calibration routine makes for no internal adjustments.

HIPOT • LCR METERS • MEGOHMMETERS • MILLIOHMMETERS

99 Memory Locations, 99 Steps, max 500

4 Binding/Banana Sockets: Front & Rear

(w x h x d):12.5 x 4.5 x 15.5 inches (312.5

Resistance

Sentry 50 Plus

510m

Ω

500

400

300

Specification Range

150m 100m

10m

200

Ω Ω

Ω

2A 10A 20A

Output Current: Range: 3.00A to 30A AC

Resolution: 0.01A, 3-30A Accuracy:±(1.5% of setting + 0.15A) Accuracy:±(1.5% of reading + 0.15A) Frequency: 50 or 60 Hz, ±0.1%

Source Voltage: Range: 1.0V to 8.0V rms

Resolution: 0.1Volt/step

Resistance: Range: 0.1mΩ - 510mΩ

Accuracy: ± (2% of reading + 2.6mΩ)

Limits: High: 0.1mΩ - 510mΩ

Low: 0.1mΩ - High Limit, or OFF

Offset: 0 to 100mΩ, user selectable Indication: Pass/Fail display, LEDs & audible alarm

Test Time: 0.5 to 999s

Continuous Mode

Standard Interface: Remote

Inputs: Start, Stop and Interlock Characteristics: 24V Active Low, Pulse Width >20ms. Outputs: Pass/Fail/Under Test Characteristics: Dry Contact relay Elec Characteristics: 30VAC/60VDC,<0.3A Logic: Closed if True Connector: 9 pin Male D-Series

Current

30A

Test Setups: Connectors: 4-Terminal Kelvin Connection

1 Chassis Ground Banana Socket

Front Panel Lockout: 11-digit password with or without setup

recall

Display: 40x4 Character Graphic LCD Hipot Compatibility: Sentry & Guardian Series Hipot Testers Dimensions:

x 112.5 x 387.5 mm)

Weight: 34 lbs (15.4kg) net,

40 lbs (18.1kg) ship

Environmental: Meets MIL-T-28800E, Type 3, Class 5

Specifications: 18°C to + 28°C, 70% RH Operating: 0°C to + 40°C, 80% RH Storage: - 10°C to + 60°C, 90% RH

Power: 100V, 120V, 220V AC ±10%

240V AC -10% +5% 50 or 60Hz 880W max

Ordering Information

Sentry 50 Plus Ground Bond Tester

Includes:

150743 Instruction Manual 700070 Power Cable G15 Ground Continuity Lead Set 520107 10A 250V Fuse (1) 520068 5A 250V Fuse (1) N/A Calibration Certificate Traceable to NIST

For more information about special purchase, rent & lease options, call

1-800-253-1230 • Fax 1-978-461-4295 • Intl. 1-978-461-2100

Optional Accessories:

Calibration Data S05 Foot Switch S15 Interconnection Cable to SPlus Series G13 Corded Product Adapter(115V) G15 Ground Continuity Lead Set G16 International Power Strip G25 Corded Product Adapter (240V)

For more detailed specifications, visit www.quadtech.com

5 Clock Tower Place, 210 East, Maynard, MA 01754

P/N 030132/