Page 1
Guardian
USES:
• Production and Compliance Testing of
Appliances, Instruments and Information
Technology Equipment in Accordance
with UL, CSA, IEC, TUV and Other
Standards such as EN60335, EN60950,
EN61010, CSA C22.2 No. 1010.1, UL3111
and UL1950
• Transformer Electrical Safety Testing
• Electric Motor Safety Testing
• Power Supply Safety Testing
• Verification of the Ground Connection on
Products with a Three Prong Power Cord
FEATURES:
• Programmable output voltage to 5KVAC
and 6KV DC
• Ground Bond Testing to 30AAC with
Adjustable Limit
• Insulation Resistance Measurements
from 100kΩΩto 50G
ΩΩ
• Programmable Ramp and Test Times
• Storage of 99 Tests Setups with 99 Steps
per Setup
• Continuous Leakage Current Monitoring
• Trip Current Programmable to 40mAAC
and 20mA DC
• Front Panel Lockout via Password
• Standard IEEE and Remote Control
Interfaces
• Optional RS232, Printer Interfaces
• Built-in 8 Channel Scanner Option
Introduction
The Guardian 6000 is four instruments in one providing AC Hipot, DC Hipot,
Insulation Resistance and Ground Bond measurements from a single test connector in one versatile instrument. This provides a cost effective solution to electrical
safety compliance testing with maximum flexibility for present and future
requirements. Performing multiple electrical safety tests in one unit can reduce
test time, increase productivity and reduce the number of instruments requiring
calibration.
Description
The Guardian 6000 AC Hipot Tester performs AC dielectric testing (hipot)over
the voltage range from 50V to 5000VAC RMS. The maximum leakage current of
40mA RMS makes the Guardian 6000 ideal for testing devices with high leakage
currents such as power supplies which have large filter or “Y” capacitors for noise
reduction.
The Guardian 6000 DC Hipot Tester voltage range for DC dielectric testing is
50V to 6000VDC with a resolution of 1V. The maximum current leakage is
20mA which allows quick charging of capacitive devices. A quick discharge of
the device when the measurement is complete, also minimizes test times.
Leakage currents can be monitored down to 0.1µA.
The Guardian 6000 Insulation Resistance measurements are similar to a DC
hipot but rather than displaying leakage current, resistance is calculated and displayed. The insulation resistance can be measured over the range of 100kΩ to
50GΩ with test voltages from 50VDC to 1000VDC in 1V steps.
The Guardian 6000 Ground Bond provides up to 30AAC for ground bond testing. The test current can be programmed from 1A to 30A in 0.1A steps. Hi current limit, test time, frequency and open circuit no load voltage can all be programmed. The offset feature can automatically compensate for any lead resistance.
1-800-253-1230
Fax 1-978-461-4295
Intl. 1-978-461-2100
For more information about special
purchase, rent & lease options, call
For more detailed
specifications, visit
www.quadtech.com
HIPOT TESTERS • LCR METERS • MEGOHMMETERS • MILLIOHMMETERS • CABLE TESTERS
6000 Series
Electrical Safety Analyzer
Page 2
AC Output Voltage: Range: 50V to 5000V AC, 1V resolution
Frequency: 50 or 60 Hz Programmable
Waveform: Sinusoidal
Regulation: <(1% +5V) at Rated Load
Voltage Display: Accuracy: ±(1% of reading + 5V)
Resolution: 1Volt
AC Current Display: Total current
Range: 0.001 to 40mAAC
Resolution: 1 or 10µA steps
Accuracy: ±(1% + 5cnt)
High/Low Limit Test: 1µA to 40mAAC
Accuracy: ±(1% of limit + 1mA)
Low limit can be turned OFF
Arc Detection: Programmable Level and OFF, >1mA
DC Output V
oltage: Range: 50V to 6000V DC, 1V resolution
Regulation: <(1% +5V) at Rated Load
Voltage Display: Accuracy: ±(1% of reading + 5V)
Resolution: 1Volt
DC Current Display: Range: 0.1µ to 20mA DC
Resolution: 0.1, 1 or 10µA steps
Accuracy: ±(1% or reading + 5cnt)
High/Low Limit Test: 0.0001mA to 20mA DC
Low limit can be turned OFF
Arc Detection: Programmable Level and OFF, >1mA
Insulation Resist
ance:
Range: 100kΩ - 50GΩ
Accuracy: ±5% to ±15% depending upon
voltage and resistance
Voltage Range: 50V to 1000V DC
Volt age Accuracy: ±(1% of setting + 5V)
High/Low Limit Test: 100kΩ - 50GΩ
Low limit can be turned OFF
IR Test Delay: 0.3 to 99.9 seconds Programmable in
0.1 second steps
Ground Bond:
Output Current: Range: 1.0 to 30.0AAC, setting 0.1A/step
Accuracy: ±(1% of setting + 0.3A)
Display: ±(1% of reading + 3 counts)
Frequency: 50 or 60Hz Selectable
No Load Voltage: 6 to 15 V Programmable
Resistance: Range: 0 - 500.0mΩ, 4 digits
Accuracy: ±(1% of reading + 3 counts)
Resolution: 1mΩ
Hi Limit: 10mV to 510mV
Offset Function: 0 to 100mV offset, user selectable
Test Time: 0.5 - 999sec (±20ms)
Common Features:
AC/DC Test Time: Ramp: 0.1 to 999s (±20ms)
Test: 0.1 to 999s (±20ms) and Continuous
Remote Control: Inputs: Start,Stop
Characteristics: Optically Isolated
with Low, Pulse Width >1ms.
Outputs: Pass/Fail/Under Test
Characteristics: Dry Contact relay
Electrical Characteristics: 120V 100mAmax.
Logic: Closed if True
Connector: Terminal Strip and 9 pin D Series
Test Setups: 99 Test Setups with 99 Steps each, Alpha-
Numeric Label
Connectors: Front and Rear Connections
Front Panel Lockout: Password
Safety Features: Fast Cutoff (<0.4ms) and Fast Discharge
Adjustable Discharge: .05-5.1kV DC
Miscellanious: Fail Retest
Scanner Delay: 0.1 to 99.9, 0.1s/step
PAUSE Mode: Program pause between steps
Indication: Pass/fail lights, audible sound
Buzzer Level: 1,2,3 and Off
Standard Interface: IEEE-488
Optional Interfaces: RS-232, Printer
Data bits: 8, Parity: None
Stop bits: 1, Default Baud Rate: 9.6k
EOS: CR + LF, Echo: Off
Selectable Baud Rate: 300 - 19200
Dimensions: (w x h x d):17x6.8x17.7in (430x175x450mm)
Weight: 53 lbs (24kg) - Net, 60 lbs (27kg) Shipping
Environmental: Operating: 0 to + 40° C,
Humidity: <75%
Storage: - 20 to + 70° C
Warm-up Time: 1minute
Power: • 90 - 130V AC • 50 or 60Hz
• 200 - 250V AC • 500W max
Guardian 6000 Electrical Safety Analyzer
Includes:
150354 Instruction Manual
S02 HV Lead Set, 1m
G15 Ground Continuity Lead Set
4200-0300 AC Power Cable
N/A Calibration Cert. Traceable to NIST
Optional Accessories
N/A Calibration Data
6000-01 Scanner, 8 Channel 5HV,3GC
6000-02 Scanner, 8 Channel 3HV,5GC
6000-03 Scanner, 8 Channel HV
S04 HV Lead Set 2m
S05 Foot Switch
S08 Gun Probe
S09 HV Lead, 1M, Unterminated
S10 HV Lead, 1M, Unterminated
G13 Corded Product Adapter (115V)
G14 Power Entry Adapter
G16 International Power Strip
G24 Scanner Cable (5000 scanners)
G25 Corded Product Adapter (240V)
G26 RS232 Interface
G27 Rack Mount Flanges
G28 Printer Interface (replace IEEE)
G41 RS232 Cable: DB9F to DB25M, 3 feet
Ordering Information
For more detailed specifications, visit www.quadtech.com • For more information about special purchase,
rent & lease options, call:
1-800-253-1230 • Fax 1-978-461-4295 • Intl. 1-978-461-2100
5 Clock Tower Place, 210 East, Maynard, MA 01754
P/N: 030081/A6
Guardian 6000
Product Specifications
Loading...