Atec GUARDIAN-5000 User Manual
Guardian
HIPOT • LCR METERS • MEGOHMMETERS • MILLIOHMMETERS
5000 SafetyAnalyzer
USES:
•Production and Compliance Testing of
Appliances, Instruments and
Information Technology Equipment in
Accordance with UL, CSA, IEC, TUV
and Other Standards such as
EN60335, EN60950, EN61010, CSA
C22.2 No. 1010.1, UL3111 and
UL1950
•Transformer Electrical Safety Testing
•Electric Motor Safety Testing
•Power Supply Safety Testing
•Verification of the Ground Connection
on Products with a Three Prong Power
Cord
FEATURES:
•Programmable output voltage to 5KV
AC and 6KV DC
•Ground Bond Testing to 30A AC with
Adjustable Limit
•Multi-point Scanner Option for High
Voltage Switching of up to 64 Points
•Programmable Ramp and Test Times
•Storage of 50 Tests Setups with 15
Steps per Setup
•Trip Current Programmable to 40mA
AC and 20mA DC
•Front Panel Lockout via Password
AC/DC/IR/GC Electrical Safety Analyzer
Introduction
The Guardian 5000 is four instruments in one providing AC Hipot, DC Hipot,
Insulation Resistance, and Ground Bond measurements from a single test connector
in one versatile instrument. This provides a cost effective solution to electrical safety compliance testing with maximum flexibility for present and future requirements.
Performing all of the electrical safety tests in one box can reduce test time, increase
productivity and reduce the number of boxes requiring calibration.
Description
The Guardian 5000 AC Hipot Testerperforms AC dielectric testing (hipot) over the
voltage range from 100V to 5000VAC RMS. The maximum leakage current of 40mA
RMS makes the Guardian 5000 ideal for testing devices with high leakage currents
such as power supplies which have large filter or “Y” capacitors for noise reduction.
Both the actual test voltage and total current are displayed during testing.
The Guardian 5000 DC Hipot Testervoltage range for DC dielectric testing is 100V
to 6000VDC with a resolution of 10V. The maximum current leakage is 20mA
which allows quick charging of capacitive devices. A quick discharge of the device
when the measurement is complete, also minimizes test times.
The Guardian 5000 Insulation Resistance measurements are similar to a DC hipot
but rather than displaying leakage current, resistance is calculated and displayed. The
insulation resistance can be measured over the range of 10M
voltages from 50VDC to 1000VDC in 1V steps.
The Guardian 5000 Ground Bondprovides up to 30A AC for ground bond testing.
The test current can be programmed from 1A to 30A in 0.1A steps. Hi current limit,
test time, frequency and open circuit no load voltage can all be programmed. The
offset feature can automatically compensate for any lead resistance.
Ω to 10GΩ with test
•Standard IEEE and Remote Control
Interfaces
•Optional RS232 Interface
•LabVIEW®Intrument Driver
Software
•Insulation Resistance Measurements
from 10M
ΩΩto 10GΩΩ 1ohm Limit
For more detailed
specifications, visit
www.quadtech.com
For more information about special
purchase, rent & lease options, call
1-800-253-1230
Fax 1-978-461-4295
Intl. 1-978-461-2100
AC Output Voltage:
Guardian 5000
Range: 100V to 5000V AC
Resolution: 10 Volts / step
Frequency: 50/60 Hz selectable
Waveform: Sinusoidal
Regulation: +/-(1% of setting +5V)
Voltage Display: Accuracy: +/-(1% of reading + 5V)
Resolution: 1Volt
AC Current Display: Total current
Range: 0.001 to 40mA AC
Resolution: 0.001mA
Accuracy:+/-(1.5% of reading + 5cnt)
High/Low Limit Test: 1mA to 40mA AC
Accuracy: +/-(1% of limit +1mA)
Low limit can be turned OFF
ArcDetection: Arc Level: >1mA to 40 mA & OFF in
0.001mA / Step
DC Output Voltage
Range: 100V to 6000V DC
Resolution: 10Volts / step
Regulation: +/-(1% of setting +5V)
Voltage Display: Accuracy: +/-(1% of reading + 5V)
Resolution: 1Volt
DC Current Display: Range:1mA to 20mA DC
Resolution: 0.001mA
Accuracy:+/-(1% of reading + 5cnt)
High/Low Limit Test: 0.001mA to 20mA DC
Low limit can be turned OFF
Arc Detection: Arc Level: >1mA to 40 mA & OFF in
0.001mA / Step
Insulation Resistance
Range: 10M Ω - 10GΩ
Accuracy: +/- 5% >= 500V 10MΩ - 1GΩ
+/-15% > 500V, 1G Ω - 10GΩ
+/-10% < 500V, 1MΩ - 200MΩ
+/- 15% < 200V, 200MΩ - 1GΩ
Voltage Range: 50V to 1000V DC
Voltage Accuracy: +/-(1% of setting +5V)
High/Low Limit Test: 10M Ω - 10GΩ
High limit can be turned OFF
IR Test Delay: 0.3 to 99.9 seconds programmable in
0.1 second steps
Ground Bond
Output Current: Range: 1.0 to 30.0A AC, setting
0.1A / step
Ordering Information
Display: +/-(1% of setting + 0.3A )
Frequency: 50 or 60Hz Selectable
No Load Voltage: 6 to 15 V programmable
Resistance: Range: 0 - 500.0mV, 4 digits
Accuracy: +/- (1% of reading + 3 cnts)
Hi Limit: 10 mV to 510 mV
Offset Function: 0 to 100 mV, user selectable
Test Time: 0.5 - 999sec(+/-20ms)
Common Features
AC/DC Test Time: Ramp: 0.1 to 99.9s (+/- 20ms)
Test: 0.1 to 999s (+/- 20ms) and
Continuous
Remote Control: Inputs: Start,Stop
Characteristics: Optically Isolated with
+24V Active Low, Pulse Width >1ms.
Outputs: Pass/Fail/Under Test
Characteristics: Dry Contact relay
Ele. Characteristics: 120V 100mA max.
Logic: Closed if True
Connect: Terminal Strip & 9 pin D Serie
Test Setups: 50 Test Setups with 15 Steps each
Connectors: Front Connection and Rear
Connections
Front Panel Lockout: Password
Safety Features: Fast Cutoff (<0.4ms) and Fast
Discharge
Miscellaneous: Continuous Voltage on Fail
Scanner Delay: 0.1 to 99.9, 0.1s/step
Indication: Pass/Fail lights, audible sound
Buzzer Level: 1,2,3 and Off
Standard Interface: IEEE488
Optional Interface: RS232
Data Bits: 8, Parity: None, Stop Bits: 1
Default Baud Rate: 9.6k
EOS: CR + LF, Echo: Off
Dimensions: (w x h x d):17 x 6.8 x 17.7in
(430 x 175 x 450mm)
Weight: 53 lbs (24kg), Net
60 lbs (27kg), Ship
Environmental: Operating: 0° to + 4°C
Humidity: <75%
Storage: - 10° to + 60°C
Power: • 90 - 130V AC • 50 or 60Hz
• 200 - 250V AC • 300W max
Guardian 5000 Electrical Safety
Analyzer
Includes:
150206 Instruction Manual
700070 Power Cable
S02 Test Leads
G15 Ground Continuity Lead Set
Calibration Certificate Traceable to NIST
For more information about special purchase, rent & lease options, call
Optional Accessories:
Calibration Data
5000-01 Scanner, 8 Channel HV
5000-02 Scanner, 8 Channel HV/4GC
5000-03 Scanner, 8 Channel HV Rack
Mountable
5000-04 Scanner, 8 Channel HV/4GC
Rack Mountable
S04 HV Lead Set, 2m
S05 Foot Switch
S06 High Voltage Probe
S10 HV Lead, 2 meters, unterminated
S11 Gun Probe with remote start
S12 Load Box, resistive
S14 Load Box, custom resistors
S08 Gun Probe
S09 HV Lead, 1 meter, unterminated
G13 Corded Product Adapter
For more detailed specifications, visit www.quadtech.com
1-800-253-1230 • Fax 1-978-461-4295 • Intl. 1-978-461-2100
5 Clock Tower Place, 210 East, Maynard MA 01754
G14 Power Entry Adapter
G15 GC Lead Set, high &low
G16 International Power Strip
G22 Rear Panel Connection (factory
installed)
G23 Rack Mount Ears
G25 Corded Product Adapter (240V)
G26 RS232 Interface
P/N 030072/ A2
Loading...