Frequency ............................................................................................................................................................................................... 3
Sweep time ............................................................................................................................................................................................. 4
Inputs and outputs .................................................................................................................................................................................. 7
R&S®FSH4/R&S®FSH8 model .24/.28 without R&S®FSH-K42 option .............................................................................................. 10
R&S®FSH4/R&S®FSH8 model .24/.28 with R&S®FSH-K41 option ................................................................................................... 11
R&S®FSH-K44 3GPP WCDMA BTS/NodeB pilot channel and pilot EVM measurement application
®
R&S
FSH-K44E 3GPP WCDMA BTS/NodeB code domain power and EVM measurement application
with HSDPA/HSPA+ analyzer ............................................................................................................................................................... 12
R&S®FSH-K46 CDMA2000® BTS pilot channel and EVM measurement application
®
FSH-K46E CDMA2000® BTS code domain power measurement application ............................................................................. 14
R&S
R&S®FSH-K47 1xEV-DO® BTS pilot channel and EVM measurement application
®
FSH-K47E 1xEV-DO® BTS PN scanner and time domain power measurement application ...................................................... 16
R&S
R&S®FSH-K48 3GPP TD-SCDMA BTS power and P-CCPCH EVM measurement application
®
FSH-K48E 3GPP TD-SCDMA/HSDPA BTS code domain power and EVM measurement application ...................................... 17
R&S
R&S®FSH-K50/R&S®FSH-K51 LTE FDD/TDD downlink pilot channel and EVM measurement application
R&S®FSH-K43 Receiver Mode and Channel Scan Measurement Application ..................................................................................... 20
General data ......................................................................................................................................................................................... 21
Equivalence of specifications for different R&S®FSH part numbers ..................................................................................................... 22
R&S®FSH-Z1 and R&S®FSH-Z18 power sensors ............................................................................................................................. 23
R&S®FSH-Z14 directional power sensor ........................................................................................................................................... 23
R&S®FSH-Z44 directional power sensor ........................................................................................................................................... 25
R&S®FSH-Z114 precision frequency reference ................................................................................................................................ 26
Ordering information .................................................................................................................................................... 27
R&S®NRP-Zxx power sensors supported by the R&S®FSH4/8/13/20 .................................................................................................. 29
Service options ..................................................................................................................................................................................... 30
Specifications apply under the following conditions:
15 minutes warm-up time at ambient temperature, specified environmental conditions met, calibration cycle adhered to.
Data without tolerances: typical values only. Data designated as “nominal” applies to design parameters and is not tested. Data
without tolerance limits is not binding.
Frequency
Frequency range R&S®FSH4 model .04/.14 9 kHz to 3.6 GHz
R&S®FSH8 model .08/.18 9 kHz to 8 GHz
R&S®FSH4 model .24 100 kHz to 3.6 GHz
R&S®FSH8 model .28 100 kHz to 8 GHz
R&S®FSH13 9 kHz to 13.6 GHz
R&S®FSH20 9 kHz to 20 GHz
Frequency resolution 1 Hz
Reference frequency, internal
Aging per year 1 × 10
Temperature drift 0 °C to +30 °C 1 × 10
+30 °C to +50 °C 3 × 10
Achievable initial calibration accuracy 5 × 10
6
6
6
7
Total reference uncertainty (time since last adjustment × aging rate) +
temperature drift + calibration accuracy
Reference frequency, with R&S®HA-Z240 GPS receiver option
Frequency uncertainty GPS on, 1 minute after satellite lock ±2.5 × 10
up to 30 minutes after loosing satellite lock ±5 × 10
Reference frequency, with R&S®FSH-Z114 precision frequency reference option
Aging per year 3.6 × 10
Temperature drift 0 °C to +50 °C 4 × 10
Achievable initial calibration accuracy 1 × 10
8
8
9
10
9
Total reference uncertainty R&S®FSH-Z114 connected
30 seconds after oscillator lock (time since last adjustment × aging rate) +
temperature drift + 3 × calibration accuracy
(nominal)
2 minutes after oscillator lock (time since last adjustment × aging rate) +
temperature drift + calibration accuracy
Frequency readout
Marker resolution 0.1 Hz
Uncertainty ±(marker frequency × reference
uncertainty + 10 % × resolution bandwidth
+ ½ (span/(sweep points – 1) + 1 Hz)
Number of sweep (trace) points 631
Marker tuning frequency step size span/630
10 Hz span 600 MHz 20 ms to 1000 s
span > 600 MHz 20 ms × span/600 MHz to 1000 s
Uncertainty span = 0 Hz nominal 1 %
span 10 Hz nominal 3 %
Bandwidths
Resolution bandwidths
Range –3 dB bandwidth 1 Hz to 3 MHz in 1/3 sequence
Bandwidth accuracy 1 Hz RBW 300 kHz nominal < 5 %
RBW > 300 kHz nominal < 10 %
Selectivity 60 dB:3 dB nominal < 5 (Gaussian type filters)
Video filters
Range –3 dB bandwidth 1 Hz to 3 MHz in 1/3 sequence
Level
Display range displayed noise floor to +30 dBm
Maximum rated input level with RF attenuation ≥ 10 dB
DC voltage R&S®FSH4/ R&S®FSH 8,
CW RF power 30 dBm (= 1 W)
Peak RF power duration < 3 s 33 dBm (= 2 W)
Max. pulse voltage 150 V
Max. pulse energy pulse width 10 µs 10 mWs
Maximum rated input level with RF attenuation < 10 dB
DC voltage 50 V
CW RF power 20 dBm (= 100 mW)
Peak RF power duration < 3 s 23 dBm (= 200 mW)
Max. pulse voltage 50 V
Max. pulse energy pulse width 10 µs 1 mWs
Intermodulation
Third-order intercept (TOI),
nominal values
Second harmonic intercept (SHI),
nominal values
model .04/.08/.14/.18
R&S®FSH4/ R&S®FSH 8, model .24/.28,
®
FSH13, R&S®FSH 20
R&S
intermodulation-free dynamic range, signal level 2 × –20 dBm, RF attenuation = 0 dB,
RF preamplifier = off
Other interfering signals,
signal level – RF attenuation < –20 dBm
FSH4/R&S®FSH8, serial number < 105000
R&S
f 3.6 GHz,
spurious at f
– 2440.7 MHz
in
3.6 GHz < f 8 GHz,
spurious at f
– 4465.7 MHz
in
< –60 dBc
< –60 dBc
R&S®FSH4/R&S®FSH8, serial number 105000, R&S®FSH13, R&S®FSH20
f 3.6 GHz,
spurious at f
– 2446.4 MHz
in
3.6 GHz < f 8 GHz,
spurious at f
– 4462.4 MHz
in
< –60 dBc
< –60 dBc
8 GHz < f 20 GHz, < –60 dBc
Other interfering signals, related to local
oscillators
f 3.6 GHz
f < 300 kHz –60 dBc
f 300 kHz < –60 dBc
f > 3.6 GHz
f < 300 kHz –54 dBc
f 300 kHz < –54 dBc
f = receive frequency
Residual spurious response input matched with 50 ,
< –90 dBm
without input signal, RBW 30 kHz,
f 3 MHz, RF attenuation = 0 dB,
tracking generator off
Level display
Logarithmic level axis 1/2/5/10/20/50/100 dB, 10 divisions
Linear level axis 0 % to 100 %, 10 divisions
Number of traces 2
Trace detectors max. peak, min. peak, auto peak, sample,
RMS
Trace functions clear/write, max. hold, min. hold, average,
view
Setting range of reference level –80 dBm to +30 dBm
Units of level axis dBm, dBmV, dBµV, V, W
Level measurement uncertainty
Absolute level uncertainty at 100 MHz +20 °C to +30 °C < 0.3 dB
Frequency response (+20 °C to +30 °C) 9 kHz f < 100 kHz
nominal < 1.5 dB
(models .04/.14/.08/.18 only)
100 kHz f < 10 MHz nominal < 1.5 dB
10 MHz f 3.6 GHz < 1 dB
3.6 GHz < f 20 GHz < 1.5 dB
Attenuator uncertainty < 0.3 dB
Uncertainty of reference level setting nominal < 0.1 dB
Display nonlinearity SNR > 16 dB, 0 dB to –50 dB,
< 0.2 dB
logarithmic level display
Bandwidth switching uncertainty reference: RBW = 10 kHz nominal < 0.1 dB
Total measurement uncertainty 95 % confidence level, +20 °C to +30 °C,
SNR > 16 dB, 0 dB to –50 dB below reference level, RF attenuation auto
10 MHz f 3.6 GHz < 1 dB, typ. 0.5 dB
3.6 GHz < f 20 GHz < 1.5 dB, typ. 1 dB
Trigger functions
Trigger
Trigger source free run, video, external
External trigger level threshold low high transition 2.4 V
high low transition 0.7 V
Gated trigger
Gate source external
Gate delay 10 µs to 100 s, min. resolution 10 µs
Impedance 50
Connector N female
VSWR 100 kHz f 1 GHz nominal < 1.5
1 GHz < f 6 GHz nominal < 2
6 GHz < f 20 GHz nominal < 3
Input attenuator RF input only 0 dB to 40 dB in 5 dB steps
AF output
AF demodulation types AM and FM
Connector 3.5 mm mini jack
Output impedance nominal 32
Voltage (open circuit) V
Power sensor
Connector 7-contact female (type Binder 712)
Power sensors supported see accessories
Tracking generator (models .14/.18/.24/.28 only)
Frequency range models .14 and .24 100 kHz to 3.6 GHz
models .18 and .28 100 kHz to 8 GHz
Connector N female, 50
VSWR 100 kHz f 1 GHz nominal < 1.5
1 GHz < f 6 GHz nominal < 2
6 GHz < f 8 GHz, models .18 and .28 nominal < 3
Output level tracking generator attenuation = 0 dB nominal 0 dBm
Tracking generator attenuator 0 dB to 40 dB in 1 dB steps
Dynamic range for isolation
measurements
measurement mode = vector voltmeter magnitude + phase, Smith chart
Return loss
Range selectable 1/2/5/10/20/50/100 dB, linear 100 %
Resolution 0.01 dB
Measurement uncertainty see figure “Uncertainty of reflection
One-port phase
Range selectable 90/180/360/1000° to 10000° in 1/2/5 steps
Resolution 0.01°
Measurement uncertainty specifications are based on a matched DUT, RBW = 100 Hz, RF attenuation = 10 dB,
nominal source power = 0 dBm, +20 °C to +30 °C
300 kHz f 3.6 GHz
0 dB return loss < 15 dB nominal < 3°
15 dB return loss < 25 dB nominal < 6°
25 dB return loss < 35 dB nominal < 20°
3.6 GHz < f 8 GHz (R&S®FSH8 only)
0 dB return loss < 15 dB nominal < 3°
15 dB return loss < 25 dB nominal < 6°
25 dB return loss < 35 dB nominal < 20°
VSWR
Range selectable 1 to 1.1, 1.5, 2, 6, 11, 21 or 71
Smith chart
Range 1, zoom × 2, × 4, × 8
Reflection coefficient
mRho range 1 to 1000 in 1, 2, 5 steps
Corrected directivity 300 kHz f 3 GHz nominal > 43 dB
3 GHz < f 6 GHz nominal > 37 dB
6 GHz < f 8 GHz nominal > 31 dB
Corrected test port match 300 kHz f 3 GHz nominal > 40 dB
3 GHz < f 6 GHz nominal > 37 dB
6 GHz < f 8 GHz nominal > 30 dB
Uncertainty of reflection measurement with R&S®FSH-K42/-K45 option
3
nominal 0 dBm to –40 dBm in 1 dB steps
VSWR, reflection coefficient, Smith chart,
cable loss, group delay, electrical length
®
measurement with the R&S
®
R&S
FSH-K45 option”
FSH-K42/
Uncertainty of reflection measurement with the R&S
Measurement range –120 dB to +80 dB
Display range selectable 1/2/5/10/20/50/100 dB, linear 100 %
Resolution 0.01 dB
Measurement uncertainty calibration method = full two port high
accuracy
see figure “Transmission magnitude
uncertainty”
Phase
Range selectable 90/180/360/1000° to 10000°
in 1/2/5 steps
Resolution 0.01°
Measurement uncertainty specifications are based on a matched DUT, RBW = 100 Hz, RF attenuation = 10 dB,
nominal source power = 0 dBm, +20 °C to +30 °C
300 kHz f 50 MHz
0 dB insertion loss < 40 dB nominal < 2°
50 MHz < f 3.6 GHz
0 dB insertion loss < 50 dB nominal < 2°
50 dB insertion loss < 70 dB nominal < 3°
3.6 GHz < f < 6 GHz (R&S®FSH8 only)
0 dB insertion loss < 50 dB nominal < 2°
50 dB insertion loss < 70 dB nominal < 3°
6 GHz f < 8 GHz (R&S®FSH8 only)
0 dB insertion loss < 50 dB nominal < 3°
50 dB insertion loss < 70 dB nominal < 5°
Dynamic range from port 1 to port 2 RF attenuation = 0 dB, tracking generator attenuation = 10 dB, RBW = 1 kHz
100 kHz f < 300 kHz typ. 70 dB
300 kHz f < 6 GHz > 70 dB, typ. 90 dB
6 GHz f < 8 GHz typ. > 50 dB
Dynamic range from port 2 to port 1 RF attenuation = 0 dB, tracking generator attenuation = 10 dB, RBW = 1 kHz
100 kHz f < 300 kHz typ. 80 dB
300 kHz f < 6 GHz > 80 dB, typ. 100 dB
6 GHz f < 8 GHz typ. > 60 dB
Test port match as specified for tracking generator
output/RF input
Transmission magnitude uncertainty
with calibration method "Full Two Port High Accuracy", f=1GHz, IF bandwidth=100Hz
R&S®FSH4/R&S®FSH8 model .24/.28 with R&S®FSH-K41 option
Return loss range 1/2/5/10/20/50/100 dB, linear 100 %
resolution 0.01 dB
VSWR range 1 to 1.1, 1.5, 2, 6, 11, 21 or 71
resolution 0.01
Reflection coefficient
mRho range 1 to 1000 in 1, 2, 5 steps
Fault resolution in m (1.5 × 108 × velocity factor/span)
Maximum permissible spurious signal RF attenuation = 0 dB nominal 0 dBm
Input selectable RF port 1 or 2
Maximum cable length depending on cable loss 1500 m
R&S®FSH-K10 GSM EDGE measurement application
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (S/N).
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
Measurements R&S
FSH-K10
Spectrum overview
RF channel power
Occupied bandwidth
Power within span
Result summary
RF channel power
Burst power
Carrier frequency error
Burst type identification
BCC (TSC) identification
GMSK phase error
GMSK magnitude error
8PSK EVM
Traffic activity
Burst power
RF channel power
Burst power
BCC (TSC) identification
Burst display (8 bursts)
Burst type identification
All specifications are given for GMSK and 8PSK modulations, SNR > 30 dB
Frequency range 15 MHz to 3.0 GHz
Carrier frequency uncertainty nominal
Lock range ±8 kHz
Measurement uncertainty SNR > 30 dB,
= uncertainty of reference frequency
f
ref
< 15 Hz + f
ref
RF Channel power
Measurement range frequency > 15 MHz
preamplifier = OFF –60 dBm < P
preamplifier = ON –75 dBm < P
Measurement uncertainty –75 dBm < P
– 30 dB < P
P
REF_LEV
< 20 dBm,
total
total
< P
REF_LEV
1 dB, typ. 0.5 dB
+ 3 dB
total
total
Burst power SNR > 30 dB, nominal
Measurement range –40 dBm < P
Measurement uncertainty P
R&S®FSH-K44 3GPP WCDMA BTS/NodeB pilot channel and pilot EVM
measurement application
®
R&S
FSH-K44E 3GPP WCDMA BTS/NodeB code domain power and EVM
measurement application with HSDPA/HSPA+ analyzer
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (SNR).
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
10 % < EVM < 25 % 2.5 %
Residual EVM typ. 1.5 %
Composite EVM 1 test case 6.7.1 in line with 3GPP TS 25.141, test model 4 with P-CPICH, SNR > 30 dB
Measurement range –40 dBm < P
10 % < EVM < 25 % typ. 2.5 %
Residual EVM typ. 2.5 %
Scrambling code detection test model 1.16 in line with 3GPP TS 25.141
Lock range ±1 kHz
Calculation time 2.5 s
CPICH EC/I0 > –21 dB
R&S®FSH-K46 CDMA2000® BTS pilot channel and EVM measurement
application
®
R&S
FSH-K46E CDMA2000® BTS code domain power measurement
application
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (SNR).
All specifications are valid for RC3, one traffic channel, SNR > 30 dB.
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
Measurements R&S
Spectrum overview ● ●
Result summary ● ●
RF channel power ● ●
Rho ● ●
Carrier frequency error ● ●
Active channels ● ●
Composite EVM ● ●
Peak to average ● ●
Pilot channel power (Cd 0) ● ●
Sync channel power (Cd 32) ● ●
Code domain power – ●
RF channel power – ●
Pilot power – ●
Sync power (rel. to RF ch. pwr./pilot) – ●
Code power (rel. to RF ch. pwr./pilot) – ●
Carrier frequency error – ●
Rho – ●
Composite EVM – ●
PN offset found – ●
Code domain channel table – ●
Channel type – ●
Walsh code/spreading factor – ●
Symbol rate (ksps) – ●
RC – ●
Status – ●
Power absolute (dBm) – ●
Power relative (rel. to RF ch. pwr./pilot) – ●
PN scanner – ●
Detected PN offset – ●
Power per detected PN offset – ●
R&S®FSH-K47 1xEV-DO® BTS pilot channel and EVM measurement
application
®
R&S
FSH-K47E 1xEV-DO® BTS PN scanner and time domain power
measurement application
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (SNR).
Measurements R&S
FSH-K47 R&S®FSH-K47E
Spectrum overview ● ●
Result summary ● ●
RF channel power ● ●
Pilot Rho ● ●
Carrier frequency error ● ●
Traffic activity ● ●
Pilot EVM ● ●
PN timing (tau) ● ●
Peak to average ● ●
Pilot power ● ●
MAC power ● ●
Data power ● ●
PN scanner – ●
Detected PN offset – ●
Power per detected PN offset – ●
Burst power – ●
RF channel power – ●
Pilot power – ●
All specifications are valid for RC3, one traffic channel, SNR > 30 dB.
Frequency range 15 MHz to 3.0 GHz
Carrier frequency uncertainty, nominal values
Lock range ±5 kHz
Measurement uncertainty SNR > 30 dB,
= uncertainty of reference frequency
f
ref
< 100 Hz + f
ref
RF channel power
Measurement range frequency > 15 MHz
preamplifier = off –60 dBm < P
preamplifier = on –75 dBm < P
Measurement uncertainty –75 dBm < P
RF channel
< 20 dBm,
< 1 dB, typ. 0.5 dB
RF channel
RF channel
< 20 dBm
< 20 dBm
ref. level adjusted to RF channel power
Pilot power SNR > 30 dB
Measurement range –40 dBm < P
Measurement uncertainty P
RF channel
– 20 dBm < P
< 20 dBm P
RF channel
CPICH
< P
RF channel
< 1 dB, typ. 0.5 dB
RF channel
– 20 dB < P
PICH
< P
RF channel
MAC power SNR > 30 dB
Measurement range –40 dBm < P
Measurement uncertainty P
RF channel
– 20 dBm < P
< 20 dBm P
RF channel
SYNC
< P
RF channel
< 1 dB, typ. 0.5 dB
RF channel
– 20 dB < P
SYNC
< P
RF channel
Data power SNR > 30 dB
Measurement range –40 dBm < P
Measurement uncertainty P
RF channel
– 20 dBm < P
< 20 dBm P
RF channel
SYNC
< P
RF channel
< 1 dB, typ. 0.5 dB
RF channel
– 20 dB < P
SYNC
< P
RF channel
Pilot EVM SNR > 30 dB
Measurement range –40 dBm < P
R&S®FSH-K48 3GPP TD-SCDMA BTS power and P-CCPCH EVM
measurement application
®
R&S
FSH-K48E 3GPP TD-SCDMA/HSDPA BTS code domain power and EVM
measurement application
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (SNR).
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
Measurements R&S
Spectrum overview
Time domain power –
Slot 0 to 6 power –
DwPTS power –
UpPTS power –
Slot 0 to 6 composite EVM –
Slot 0 to 6 C/I –
Sync ID –
Sync ID # –
Sync ID power –
Sync ID delay –
Code domain power –
Code #/SF (spreading factor) –
Modulation type (QPSK, 8PSK, 16QAM, 64QAM) –
Symbol EVM –
Code power –
RF channel power –
Composite EVM –
Code domain channel table –
Code #/SF (spreading factor) –
Modulation type (QPSK, 8PSK, 16QAM, 64QAM) –
Symbol EVM –
Code power abs/rel –
Limits screen –
Result summary
The specifications below apply to the R&S®FSH4 and R&S®FSH8. They are based on the data sheet specifications of the R&S®FSH4
and R&S
indicated as 95 % confidence intervals. The specified level measurement errors do not take into account systematic errors due to
reduced signal-to-noise ratio (S/N).
All specifications are valid for SNR > 30 dB.
®
FSH8, have not been checked separately and are not verified during instrument calibration. Measurement uncertainties are
Measurements R&S
Spectrum overview
Result summary
RF channel power
Carrier frequency error
I/Q offset
Cell identity
Cyclic prefix
Reference signal power
PSYNC power
SSYNC power
PBCH power
PCFICH power
PDSCH power
Reference signal EVM
PSYNC EVM
SSYNC EVM
PBCH EVM
PCFICH EVM
R&S®HA-Z201 plug-in AC power supply input specifications 100 V to 240 V AC, 50 Hz to 60 Hz,
700 mA
output specifications 15 V DC, 2 A
operating temperature range 0 °C to +40 °C
storage temperature range –40 °C to +70 °C
test mark VDE, CE, UL, PSE
External DC voltage 14 V to 16 V
Internal battery Li-ion battery
Capacity R&S®HA-Z204 (standard) 4.5 Ah
R&S®HA-Z206 (option) 6.75 Ah
Voltage nominal 7.2 V
Operating time with new,
fully charged battery
R&S®HA-Z204 (standard) 3 h
R&S®HA-Z206 (option) 4.5 h
Charging time instrument switched off or R&S®HA-Z203 battery charger
R&S®HA-Z204 (standard) 2.5 h
R&S®HA-Z206 (option) 3.5 h
instrument switched on
R&S®HA-Z204 (standard) 3.5 h
R&S®HA-Z206 (option) 4.5 h
Life time charging cycles > 500
Power consumption typ. 12 W
Safety IEC 61010-1, EN 61010-1, UL 61010-1,
CAN/CSA-C22.2 No. 61010.1-04
Test mark VDE, GS, CSA, CSA-NRTL
EMC in line with European EMC Directive
2004/108/EC including
EN 61326 class B (emission)
CISPR 11/EN 55011/group 1
class B (emission)
EN 61326 table 2 (immunity, industrial)
field strength:
30 V/m: 30 MHz to 2 GHz
3 V/m: 2 GHz to 2.7GHz
Dimensions (W × H × D) with handle 194 mm × 300 mm × 144 mm
(7.6 in × 11.8 in × 5.7 in)
without handle 194 mm × 300 mm × 69 mm
(7.6 in × 11.8 in × 2.7 in)
Weight < 3 kg (< 6.6 lb)
Recommended calibration interval 1 year
Equivalence of specifications for different R&S®FSH part numbers
• The specifications for part number 1309.6000.54 are equivalent to part number 1309.6000.04
• The specifications for part number 1309.6000.64 are equivalent to part number 1309.6000.14
• The specifications for part number 1309.6000.74 are equivalent to part number 1309.6000.24
• The specifications for part number 1309.6000.58 are equivalent to part number 1309.6000.08
• The specifications for part number 1309.6000.68 are equivalent to part number 1309.6000.18
• The specifications for part number 1309.6000.78 are equivalent to part number 1309.6000.28
• The specifications for part number 1314.2000.63 are equivalent to part number 1314.2000.13
• The specifications for part number 1314.2000.80 are equivalent to part number 1314.2000.20
Maximum input power average power 400 mW (+26 dBm)
peak power (< 10 µs, 1 % duty cycle) 1 W (+30 dBm)
Measurement range 200 pW to 200 mW
(–67 dBm to +23 dBm)
Signal weighting average power
Effect of harmonics < 0.5 % (0.02 dB)
Effect of modulation < 1.5 % (0.07 dB)
Absolute measurement uncertainty sine signals, no zero offset
10 MHz to 8 GHz +15 °C to +35 °C < 2.3 % (0.10 dB)
0 °C to +50 °C < 4.2 % (0.18 dB)
8 GHz to 18 GHz +15 °C to +35 °C < 3.5 % (0.15 dB)
0 °C to +50 °C < 5.0 % (0.21 dB)
Zero offset after zeroing < 110 pW
Dimensions (W × H × D) 48 mm × 31 mm × 170 mm
connecting cable 1.5 m (59 in)
Weight < 0.3 kg (0.66 lb)
at harmonic ratio of 20 dB
for continuous digital modulation
(1.9 in × 1.22 in × 6.7 in)
R&S®FSH-Z14 directional power sensor
Frequency range 25 MHz to 1 GHz
Power measurement range 30 mW to 300 W
VSWR referenced to 50 < 1.06
Power-handling capacity depending on temperature and matching
Insertion loss < 0.06 dB
Directivity > 30 dB
Average power
Power measurement range
CW, FM, PM, FSK, GMSK CF: ratio of peak envelope 30 mW to 300 W
Modulated signals power to average power 30 mW to 300 W/CF
Measurement uncertainty
25 MHz to 40 MHz sine signal 4.0 % of measured value (0.17 dB)
40 MHz to 1 GHz +18 °C to +28 °C, no zero offset 3.2 % of measured value (0.14 dB)
Zero offset after zeroing ±4 mW
Range of typical measurement error
with modulation
Temperature coefficient 25 MHz to 40 MHz 0.40 %/K (0.017 dB/K)
(see diagram on page 20)
FM, PM, FSK, GMSK 0 % of measured value (0 dB)
AM (80 %) ±3 % of measured value (±0.13 dB)
two CW carriers with identical power ±2 % of measured value (±0.09 dB)
Frequency range 200 MHz to 4 GHz
Power measurement range 30 mW to 300 W
VSWR referenced to 50 200 MHz to 3 GHz < 1.07
3 GHz to 4 GHz < 1.12
Power-handling capacity depending on temperature and matching
(see diagram on page 22)
Insertion loss 200 MHz to 1.5 GHz < 0.06 dB
1.5 GHz to 4 GHz < 0.09 dB
Directivity 200 MHz to 3 GHz > 30 dB
3 GHz to 4 GHz > 26 dB
Average power
Power measurement range CF: ratio of peak envelope power to average power
CW, FM, PM, FSK, GMSK 30 mW to 300 W
3GPP WCDMA, cdmaOne,
CDMA2000
®
, DAB, DVB-T
other modulated signals 30 mW to 300 W/CF
Measurement uncertainty sine signal, +18 °C to +28 °C, no zero offset
200 MHz to 300 MHz 4.0 % of measured value (0.17 dB)
300 MHz to 4 GHz 3.2 % of measured value (0.14 dB)
Zero offset after zeroing ±4 mW
Range of typical measurement error
with modulation
FM, PM, FSK, GMSK 0 % of measured value (0 dB)
AM (80 %) ±3 % of measured value (±0.13 dB)
two CW carriers with identical power ±2 % of measured value (±0.09 dB)
/4-DQPSK ±2 % of measured value (±0.09 dB)
EDGE ±0.5 % of measured value (±0.02 dB) 4
cdmaOne, DAB ±1 % of measured value (±0.04 dB) 4
3GPP WCDMA, CDMA2000® ±2 % of measured value (±0.09 dB) 4
DVB-T ±2 % of measured value (±0.09 dB) 4
Temperature coefficient 200 MHz to 300 MHz 0.40 %/K (0.017 dB/K)
300 MHz to 4 GHz 0.25 %/K (0.011 dB/K)
Max. peak envelope power
Power measurement range
DAB, DVB-T, cdmaOne, CDMA2000®,
4 W to 300 W
3GPP WCDMA
Other signals at video bandwidth 4 kHz 0.4 W to 300 W
200 kHz 1 W to 300 W
4 MHz 2 W to 300 W
Measurement uncertainty +18 °C to +28 °C same as for average power plus effect of
Error limits of peak hold circuit for burst
signals
duty cycle 0.1 and repetition rate 100/s
video bandwidth 4 kHz ±(3 % of measured value + 0.05 W)
video bandwidth 200 kHz ±(3 % of measured value + 0.20 W)
video bandwidth 4 MHz ±(7 % of measured value + 0.40 W)
20/s repetition rate < 100/s plus ±(1.6 % of measured value + 0.15 W)
0.001 duty cycle < 0.1 plus ±0.10 W
burst width 0.5 µs plus ±5 % of measured value
burst width 0.2 µs plus ±10 % of measured value
Range of typical measurement error of
peak hold circuit
video bandwidth 4 MHz and standard selected on the R&S®FSH4/R&S®FSH8
cdmaOne, DAB ±(5 % of measured value + 0.4 W)
DVB-T, CDMA2000®, 3GPP WCDMA ±(15 % of measured value + 0.4 W)
Temperature coefficient 200 MHz to 300 MHz 0.50 %/K (0.022 dB/K)
Return loss 200 MHz to 3 GHz 0 dB to +23 dB
VSWR 3 GHz to 4 GHz 0 dB to +20 dB
VSWR 200 MHz to 3 GHz > 1.15
3 GHz to 4 GHz > 1.22
Minimum forward power specifications complied with 0.2 W 0.03 W
Dimensions (W × H × D) 120 mm × 95 mm × 39 mm
(4.72 in × 3.74 in × 1.53 in)
connecting cable 1.5 m (59 in)
Weight 0.65 kg (1.43 lb)
6
4
2
0
Error limits/dB
–2
0.2 GHz to 3 GHz
3 GHz to 4 GHz
1000
800
600
AVG –10 °C to +35 °C
400
Forward power/W
200
SWR ≤ 3
AVG +35 °C to +50 °C
SWR ≤ 3
PEAK (max. 10 ms), SWR ≤ 3
AVG –10 °C to +35 °C
SWR ≤ 1.5
–4
0252015105
Return loss/dB
Error limits for matching measurements.
100
0.20.40.71234
Frequency/GHz
Power-handling capacity.
R&S®HA-Z240 GPS receiver
GPS location indication latitude, longitude
Reference frequency uncertainty GPS on, 1 minute after satellite lock ±2.5 × 10
up to 30 minutes after losing satellite lock ±5 × 10
Temperature operating temperature range –20 °C to +55 °C
storage temperature range –40 °C to +70 °C
Climatic loading GPS receiver module IEC 60529 IPX7 level
Connector 7-contact male (type Binder 712)
Power consumption 0.45 W
Test marks FCC, CE
Dimensions diameter × height Ø 61 mm × 19.5 mm (Ø 2.4 in × 0.8 in)
cable length 5 m (16.4 ft)
Weight 200 g (0.4 lb)
8
8
R&S®FSH-Z114 precision frequency reference
Temperature operating temperature range –10 °C to +55 °C
storage temperature range –55 °C to +90 °C
Climatic loading relative humidity +25/+55 °C at 95 % relative humidity
(EN 60068-2-30)
IP class of protection 51
Connector 7-contact male (type Binder 712)
Power consumption 0.20 W
Dimensions diameter × height 88 mm × 94 mm × 26.0 mm
(3.5 in × 3.5 in × 0.8 in)
cable length 0.25 m (0.82 ft)
Weight 250 g (0.6 lb)
Spectrum Analyzer, 9 kHz to 3.6 GHz,with preamplifier R&S®FSH4 1309.6000.04
Spectrum Analyzer, 9 kHz to 3.6 GHz,
with preamplifier and tracking generator
Spectrum Analyzer, 100 kHz to 3.6 GHz, with preamplifier,
tracking generator and internal VSWR bridge
Spectrum Analyzer, 9 kHz to 8 GHz, with preamplifier R&S®FSH8 1309.6000.08
Spectrum Analyzer, 9 kHz to 8 GHz,
with preamplifier and tracking generator
Spectrum Analyzer, 100 kHz to 8 GHz,
with preamplifier, tracking generator and internal VSWR bridge
Spectrum Analyzer, 100 kHz to 13.6 GHz, with preamplifier R&S®FSH13 1314.2000.13
Spectrum Analyzer, 100 kHz to 20 GHz, with preamplifier R&S®FSH20 1314.2000.20
Accessories supplied
Li-ion battery pack, USB cable, LAN cable, AC power supply, CD-ROM with R&S®FSH4View software and documentation,
quick start guide
Options
Designation Type Order No. Remarks
Spectrogram Measurement Application R&S®FSH-K14 1304.5770.02
Interference Analysis Measurement Application R&S®FSH-K15 1309.7488.02
Geotagging Measurement Application R&S®FSH-K16 1309.7497.02
Remote Control via LAN or USB R&S®FSH-K40 1304.5606.02
Distance-to-Fault Analysis
(for models .24 and .28 only, requires R&S
®
FSH-Z321 and R&S®FSH-Z28 or R&S®FSH-Z29)
R&S
Vector Network Analysis
(for models .24 and .28 only)
Vector Voltmeter
(for models .24 and .28 only)
GSM Edge Measurement Application R&S®FSH-K10 1304.5864.02
3GPP WCDMA BTS/NodeB Pilot Channel and EVM
Measurement Application
3GPP WCDMA BTS/NodeB Code Domain Power and EVM
Measurement Application
CDMA2000® BTS Pilot Channel and EVM Measurement
Application
CDMA2000® BTS Code Domain Power Measurement
Application (R&S
®
FSH-K46 required)
1xEV-DO® BTS Pilot Channel and EVM Measurement
Application
1xEV-DO® BTS PN Scanner and Time Domain Power
Measurement Application (R&S
®
FSH-K47 required)
3GPP TD-SCDMA BTS power and P-CCPCH EVM
measurement application
3GPP TD-SCDMA/HSDPA BTS Code Domain Power and EVM
Measurement Application (R&S
®
FSH-K48 required)
LTE FDD Downlink Pilot Channel and EVM Measurement
Application
LTE TDD Downlink Pilot Channel and EVM Measurement
Application
LTE FDD Downlink Extended Channel and Modulation
Measurement Application (R&S
LTE TDD Downlink Extended Channel and Modulation
Measurement Application (R&S
®
FSH-K50 required)
®
FSH-K51 required)
Receiver Mode and Channel Scan Measurement Application R&S®FSH-K43 1304.5635.02
RF Cable (length 1 m), DC to 8 GHz, armored, N male/N female connectors R&S®FSH-Z320 1309.6600.00
RF Cable (length 3 m), DC to 8 GHz, armored, N male/N female connectors R&S®FSH-Z321 1309.6617.00
Precision Frequency Reference R&S®FSH-Z114 1304.5935.02
Combined Open/Short/50 Load Calibration Standard, DC to 3.6 GHz R&S®FSH-Z29 1300.7510.03
Combined Open/Short/50 Load Calibration Standard, DC to 8 GHz R&S®FSH-Z28 1300.7810.03
Combined Open/Short/50 Load/Through Calibration Standard, DC to 15 GHz,
3.5 mm male
Combined Open/Short/50 Load/Through Calibration Standard, DC to 15 GHz,
3.5 mm female
Combined Open/Short/50 Load/Through Calibration Standard, DC to 9 GHz,
N male
Combined Open/Short/50 Load/Through Calibration Standard, DC to 9 GHz,
N female
Matching Pad 50/75 , L section R&S®RAM 0358.5414.02
Matching Pad 50/75 , series resistor 25 R&S®RAZ 0358.5714.02
Matching Pad 50/75 , L section, N to BNC R&S®FSH-Z38 1300.7740.02
Adapter N (m) – BNC (f) 0118.2812.00
Adapter N (m) – N (m) 0092.6581.00
Adapter N (m) – SMA (f) 4012.5837.00
Adapter N (m) – 7/16 (f) 3530.6646.00
Adapter N (m) – 7/16 (m) 3530.6630.00
Adapter N (m) – FME (f) 4048.9790.00
Adapter BNC (m) – Banana (f) 0017.6742.00
Attenuator 50 W, 20 dB, 50 , DC to 6 GHz, N(f) – N(m) R&S®RDL50 1035.1700.52
Attenuator 100 W, 20 dB, 50 , DC to 2 GHz, N(f) – N(m) R&S®RBU100 1073.8495.20
Attenuator 100 W, 30 dB, 50 , DC to 2 GHz, N(f) – N(m) R&S®RBU100 1073.8495.30
12 V Car Adapter for cigarette lighter 5 R&S®HA-Z202 1309.6117.00
Li-Ion Battery Pack, 4.5 Ah R&S®HA-Z204 1309.6130.00
Li-Ion Battery Pack, 6.75 Ah R&S®HA-Z206 1309.6146.00
Battery Charger for R&S®HA-Z204 and R&S®HA-Z206 Li-ion battery pack 6 R&S®HA-Z203 1309.6123.00
Soft Carrying Bag R&S®HA-Z220 1309.6175.00
Hard Case R&S®HA-Z221 1309.6181.00
Carrying Holster, including chest harness and rain cover R&S®HA-Z222 1309.6198.00
Shoulder Strap for Carrying Holster R&S®HA-Z222 R&S®HA-Z223 1309.6075.00
SD Memory Card, 4 Gbyte 7 R&S®HA-Z232 1309.6223.00
Headphones R&S®FSH-Z36 1145.5838.02
GSM/UMTS/CDMA antenna magnetic mount 850/900/1800/1900/2100 band,
N connector
Handheld Log-Periodic Antenna, 450 MHz to 8 GHz R&S®HL300 4097.3005.02
Active Directional Antenna, 20 MHz to 7.5 GHz R&S®HE300 4067.5900.02
Loop Antenna for R&S®HE300, 9 kHz to 20 MHz R&S®HE300HF 4067.6806.02
Near-Field Probe Set R&S®HZ-15 1147.2736.02
Preamplifier for R&S®HZ-15 R&S®HZ-16 1147.2720.02
Spare USB Cable R&S®HA-Z211 1309.6169.00
Spare Ethernet Cable R&S®HA-Z210 1309.6152.00
Spare Power Supply, incl. mains plug for EU, GB, US R&S®HA-Z201 1309.6100.00
Power cord + adapter for R&S®HA-Z201 power supply (changes the power supply to laptop style)
Power cord EU R&S®HA-Z209 1309.7465.02
Power cord GB R&S®HA-Z209 1309.7465.03
Power cord US/JP R&S®HA-Z209 1309.7465.04
Power cord AUS R&S®HA-Z209 1309.7465.05
GPS Receiver R&S®HA-Z240 1309.6700.03
Spare CD-ROM including R&S®FSH4View Software and Operating Manual for
®
FSH4/R&S®FSH8
R&S
Spare printed Quick Start Guide for R&S®FSH4/R&S®FSH8, English R&S®FSH-Z46 1309.6269.12
Spare printed Quick Start Guide for R&S®FSH4/R&S®FSH8, German R&S®FSH-Z47 1309.6269.11
R&S®ZV-Z135 1317.7677.02
R&S®ZV-Z135 1317.7677.03
R&S®ZV-Z170 1317.7683.02
R&S®ZV-Z170 1317.7683.03
R&S®TS95A16 1118.6943.16
R&S
FSH-Z45 1309.6246.00
5
Note: The car adapter is suitable for both the instrument and the R&S®HA-Z203 external battery charger.
6
Note: The battery charger is dedicated for charging an additional battery outside the instrument. The internal battery is charged by the instrument itself.
7
Note: Firmware update is installed from SD memory card.
Isotropic Antenna, 30 MHz to 3 GHz for R&S®TS-EMF R&S®TSEMF-B1 1074.5719.02
Isotropic Antenna, 700 MHz to 6 GHz for R&S®TS-EMF R&S®TSEMF-B2 1074.5702.02
Isotropic Antenna, 9 kHz to 200 MHz for R&S®TS-EMF R&S®TSEMF-B3 1074.5690.02
R&S®NRP-Zxx power sensors supported by the R&S®FSH4/8/13/20 8 9
Designation Type Order No.
Power Sensor, 10 MHz to 8 GHz R&S®FSH-Z1 1155.4505.02
Power Sensor, 10 MHz to 18 GHz R&S®FSH-Z18 1165.1909.02
Directional Power Sensor, 25 MHz to 1 GHz R&S®FSH-Z14 1120.6001.02
Directional Power Sensor, 200 MHz to 4 GHz R&S®FSH-Z44 1165.2305.02
Universal Power Sensor, 10 MHz to 8 GHz, 100 mW, 2-path R&S®NRP-Z211 1417.0409.02
Universal Power Sensor, 10 MHz to 8 GHz, 200 mW R&S®NRP-Z11 1138.3004.02
Universal Power Sensor, 10 MHz to 18 GHz, 100 mW, 2-path R&S®NRP-Z221 1417.0309.02
Universal Power Sensor, 10 MHz to 18 GHz, 200 mW R&S®NRP-Z21 1137.6000.02
Universal Power Sensor, 10 MHz to 18 GHz, 2 W R&S®NRP-Z22 1137.7506.02
Universal Power Sensor, 10 MHz to 18 GHz, 15 W R&S®NRP-Z23 1137.8002.02
Universal Power Sensor, 10 MHz to 18 GHz, 30 W R&S®NRP-Z24 1137.8502.02
Universal Power Sensor, 10 MHz to 33 GHz, 200 mW R&S®NRP-Z31 1169.2400.02
Thermal Power Sensor, 0 Hz to 18 GHz, 100 mW R&S®NRP-Z51 1138.0005.02
Thermal Power Sensor, 0 Hz to 40 GHz, 100 mW R&S®NRP-Z55 1138.2008.02
Thermal Power Sensor, 0 Hz to 50 GHz, 100 mW R&S®NRP-Z56 1171.8201.02
Thermal Power Sensor, 0 Hz to 67 GHz, 100 mW R&S®NRP-Z57 1171.8401.02
Wideband Power Sensor, 50 MHz to 18 GHz, 100 mW R&S®NRP-Z81 1137.9009.02
Average Power Sensor, 9 kHz to 6 GHz, 200 mW R&S®NRP-Z91 1168.8004.02
Average Power Sensor, 9 kHz to 6 GHz, 2 W R&S®NRP-Z92 1171.7005.02
NRP-Zxx power sensors require the following adapter cable for operation on the R&S®ZVH
R&S
Passive USB adapter to connect R&S®NRP-Zxx sensors to the R&S®ZVH R&S®NRP-Z4 1146.8001.02
FSH power sensors require the following adapter cable for connection to a PC
R&S
USB Adapter Cable for R&S®FSH-Z1/R&S®FSH-Z18 R&S®FSH-Z101 1164.6252.02
USB Adapter Cable for R&S®FSH-Z14/R&S®FSH-Z44 R&S®FSH-Z144 1145.5905.02
8
For average power measurements only.
9
R&S®NRP-Zxx power sensors are supported by instruments with serial number 105000.
Extended Warranty, one year R&S®WE1FSH Please contact your local
Extended Warranty, two years R&S®WE2FSH
Extended Warranty, three years R&S®WE3FSH
Extended Warranty, four years R&S®WE4FSH
Extended Warranty with Calibration Coverage, one year R&S®CW1FSH
Extended Warranty with Calibration Coverage, two years R&S®CW2FSH
Extended Warranty with Calibration Coverage, three years R&S®CW3FSH
Extended Warranty with Calibration Coverage, four years R&S®CW4FSH
Extended warranty with a term of one to four years (WE1 to WE4)
Repairs carried out during the contract term are free of charge
10
. Necessary calibration and adjustments carried out during repairs are
also covered. Simply contact the forwarding agent we name; your product will be picked up free of charge and returned to you in top
condition a couple of days later.
Extended warranty with calibration (CW1 to CW4)
Enhance your extended warranty by adding calibration coverage at a package price. This package ensures that your
Rohde & Schwarz product is regularly calibrated, inspected and maintained during the term of the contract. It includes all repairs
calibration at the recommended intervals as well as any calibration carried out during repairs or option upgrades.
CDMA2000
®
is a registered trademark of the Telecommunications Industry Association (TIA-USA).
Rohde & Schwarz sales
office.
10
and
For product brochure, see PD 5214.0482.12 and www.rohde-schwarz.com.
10
Excluding defects caused by incorrect operation or handling and force majeure. Wear-and-tear parts are not included.
❙ Worldwide
❙ Local and personalized
❙ Customized and flexible
❙ Uncompromising quality
❙ Long-term dependability
About Rohde & Schwarz
Rohde & Schwarz is an independent group of companies
specializing in electronics. It is a leading supplier of solutions in the fields of test and measurement, broadcasting,
radiomonitoring and radiolocation, as well as secure
communications. Established more than 75 years ago,
Rohde & Schwarz has a global presence and a dedicated
service network in over 70 countries. Company headquarters are in Munich, Germany.
Environmental commitment
❙ Energy-efcient products❙ Continuous improvement in environmental sustainability❙ ISO 14001-certied environmental management system
Cert ied Quali ty Syste m
ISO 9001
Rohde & Schwarz GmbH & Co. KG
www.rohde-schwarz.com
Regional contact
❙ Europe, Africa, Middle East | +49 89 4129 12345
customersupport@rohde-schwarz.com
❙ North America | 1 888 TEST RSA (1 888 837 87 72)