Atec Fluke-750 User Manual

Fluke 750 Series

Documenting Process Calibrators:

Work smarter. Work faster.

Fluke 750 Series Documenting

Process Calibrators:

Work Smarter. Work Faster.

Whether you’re calibrating instruments, troubleshoot­ing a problem or running routine maintenance, Fluke
750 Series process calibrators can help you get the
job done faster. It does so many different tasks, so
quickly and so well, it’s the only process calibrator you
need to carry.

• Multifunctional. Calibrate temperature, pressure,
voltage, current, resistance, and frequency. Since it
both measures and sources, you can troubleshoot
and calibrate all with one rugged tool.

• Powerful, yet easy to use. The easy-to-follow,
menu-driven display guides you through any task.
Programmable calibration routines enable you to
create and run automated as-found/as-left
procedures to ensure fast, consistent, calibrations.

• Records and documents results.
To support your ISO-9000 or regulatory
standards, the Fluke 753, and 754 capture your
calibration results, eliminating the need to juggle a
pen and pad in the field. The USB interface in the
Fluke 753 and 754 lets you transfer the results to
a PC, thus saving the time of having to manually
transcribe them when you return to the shop.

• Supports popular instrumentation management
software. The 753 and 754 work with the Fluke

DPC/TRACK™ software, and with popular programs
from Honeywell Meridium, Emerson, Cornerstone,
Yokogawa, Prime Tech

It allows you to create procedures, instructions,

ers.
and action lists to deliver fast, easy documentation.

• Truly hand-held. Small enough to fit easily into a
tool bag and to use in tight spaces. Runs an entire
shift on a rechargeable Li-ion battery pack.

• Rugged and reliable. Overmolded urethane case
stands up to rough handling in industrial environ­ments. Calibrators offer one- or two-year calibration
cycles and three-year warranty.

• Bright white display lets you read your results in
any kind of light. Backlight has three (3) settings.

• Soft keys provide one-touch access to enhanced
functions such as task lists, automated procedures,
scaling, min/max, stepping and ramping, andreview
memory.

• Three operating modes Measure, Source, or
simultaneous Measure/Source, —enable technicians
to troubleshoot, calibrate, or maintain
instrumentation with just one tool.

• Integrated HART communication capability
lets you program and control HART instrumentation
(754 only).

• Use it immediately. If you’ve used the Fluke 74X
Documenting Process Calibrator you’ll be able to
pick up the 75X and start using it immediately,
without a learning curve.

nologies, Intergraph and oth-

• Multi-lingual interface displays instructions in Eng-
lish, French, German, Spanish, and Italian.

• AutoStep allows technicians to set the calibrator for
a delayed start and a specific sequence of steps, so
it can run unattended as a continuously varying test
source.

• User entered values enable users to capture
readings measured or sourced by other devices.

• Custom units allow readings to be scaled and
displayed in any user-defined units.

• Switch calibration procedures perform fast,
automated calibration of one- and two-point switches
for voltage, current, temperature, and pressure.

• Differential pressure flow
instrument calibration routines use a square root

function to directly calibrate DP flow instruments.

• Built-in algebraic calculator
with four functions— plus square root—stores, recalls,
and performs calculations required for setting up
instruments or evaluating data in the field. Use it to
set the source function to a calculated value. There’s
no need to carry a pencil and paper or a separate
calculator.

• Programmable measurement delay inside
automated procedures permits calibrating
instruments that respond slowly.

Get the knowledge straight from the product
expert in these process tools videos:

719 Electric Pressure Calibrator
789 ProcessMeter
773 Milliamp Process Clamp Meter
754 Video Series

™

Online now at www.fluke.com/ptoolsvideos

Bonus feature available with
product registration:

• Transmitter mode: simulate a transmitter

while you get a replacement.

2 Fluke Corporation 750 Series Brochure

Fluke 750 Series Documenting Process Calibrators:

Calibrators as versatile as you are.

The Fluke 750 Calibrators, offered in two models, let
you choose the right set of capabilities for your needs.

• The Fluke 753 offers simultaneous source and mea-
sure capabilities for all common process parameters.
Create and execute automated procedures and auto­matically capture the results results. The USB inter­face enables two-way communication with popular
PC-based instrumentation management applications.

• The Fluke 754 offers all of the capabilities of the
753, plus the ability to maintain and calibrate se­lected HART transmitters without a second tool.

Capability 753 754

Source / measure • •
Automated procedures • •
Results capture • •
Uses all Fluke pressure modules • •
Transmitter mode • •
Serial interface • •
Data logging • •
HART communications •
Pulsed RTD simulation to 1 ms • •
Li-ion battery with “Gas Gauge” • •

Fluke 754 HART Documenting Process Calibrator:

Get HART-ability.

Process plants have taken advantage of smart
transmitters, the need for a new generation of
calibrators has emerged— calibrators that can
communicate via industry standard digital protocols.
The 754 combines HART communication capability in a
documenting process calibrator to deliver an integrated
communicating calibrator. This rugged, reliable tool is
ideal for calibrating, maintaining, and troubleshooting
HART instrumentation. The 754 offers:

• Integrated HART communication functions,
permitting you to monitor, control, and calibrate
HART instrumentation.

• Handling of fast pulsed RTD transmitters and PLCs,
with pulses as short as 1 mS.

Li-ion battery with 4400 mA hour life and gas gauge.

•

The field calibrator for HART instruments that’s
both powerful and easy to use.

The 754 offers the most complete HART
implementation of any process calibrator. The 754:

• Requires no external box or second tool for everyday
HART calibration and maintenance.

• Offers fast HART communication.

• Supports popular models of HART transmitters with

device-specific command support.

• Fully complies with the Data Link Layer of the HART
protocol, including multiple masters, burst mode,
and multi-drop configurations.

• Is easy to update as additional instruments are
added and new HART versions are released.

• Is based on the 740 series calibrators, the most
rugged, reliable multifunction field calibrators
ever made.

• Is backed by the service and support of the
Fluke organization, a member of the HART
Communications Foundation.

The 754 is designed to take on nearly all the day­to-day tasks you now perform with a separate com­municator. In fact, it offers many of the communication
capabilities of the 475 HART communicator except
for the DD interpreter, which can read command set
libraries from any HART supplier. This is not necessary
for daily HART maintenance.

3 Fluke Corporation 750 Series Brochure

It’s easy to calibrate and maintain HART instrumentation with one powerful tool.

+

–

With the 754 DPC, you can:

• Generate precision electrical, temperature, or
pressure signals for analog stimulus or sensor
simulation.

• Simultaneously measure electrical, temperature,
or pressure signals from transmitter output.

• Determine type, manufacturer, model, tag ID by
interrogating HART devices.

• Read HART PV function and smart transmitter
digital output while measuring analog mA output.

• Read and write HART configuration functions to
make field adjustments to PV range points, damping,
and other top-level configuration settings.

• Change sensor configuration on supported
temperature transmitters.

• Re-label smart transmitters by reading and writing
HART tag and message fields.

• Clone additional transmitters by reading and
storing basic HART configurations.

• Perform automated HART sensor trim and output
trim for selected devices in conjunction with
As Found/As Left tests.

• Perform loop test with simultaneous analog and
digital mA readout.

• Address new, fast, pulsed-excitation smart
trans-mitters and PLCs.

• Control Hart Scientific Dry Block Calibrator.

4 Fluke Corporation 750 Series Brochure

HART applications

Fluke 754: The HART calibrator that is easy to use.

Versatile HART protocol support

The 754 supports the commands contained in HART
protocol version 5.7. The 754 supports a substantial set
of HART instructions:

• Universal commands—provide functions that are
implemented in all field devices, for example, read
manufacturer and device type, read primary variable
(PV), or read current output and percent of span

• Common practice commands—provide functions
that are common to many but not all field devices,
for example read multiple variables, set damping
time, or perform loop test

• Device-specific commands—provide functions
that are unique to a particular field device, for
example sensor trim. The 754 supports these
devices:

Today’s 754 supports device-specific instructions for a
variety of popular instruments. Additional support may
be added periodically with a simple software update
available on diskette or via download for a modest
upgrade fee.

HART operating modes supported

• For Point to Point operation, the most commonly
used mode, connects the 754 to a single HART
device in a 4-20 mA loop.

• In Multi-Drop mode, several HART instruments
can be bussed together. The 754 searches for each,
identifies addresses in use, and allows you to select
the instrument for calibration and related operations.

• In Burst Mode, the HART instrument transmits
bursts of data without waiting to be interrogated
by a master unit. The 754 can take transmitters out
of burst mode during test or calibration, then later
restore them to burst mode.

Manufacturer Pressure instruments Temperature instruments Coriolis instruments

ABB/Kent-Taylor 600T 658T
ABB/ Contrans P,1

Hartmann & Braun AS 800 Series
Endress & Hauser CERABAR S, TMT 122

CERABAR M, TMT 162
DELTABAR S

Foxboro Eckardt TI/RTT20
Foxboro/Invensys I/A Pressure
Fuji FCX FRC

FCXAZ
Honeywell ST3000 STT25T
Micro Motion 2000

2000 IS
9701
9712
9739

Moore Products 344
Rosemount 1151 3044C

2088 644
3001C 3144
3051, 3051S 3244, 3144P

Siemens SITRANS P DS
SITRANS P ES

SMAR LD301 TT301
Viatran I/A Pressure
Wika UNITRANS T32H
Yokogawa EJA YTA 110, 310 and 320

1

Sensor Trim not supported

1

1

, TMT 1821,

1

1

1

, STT25H

1

1

1

1

5 Fluke Corporation 750 Series Brochure

www.uke.com/processtools

Why use “smart” instrumentation?

Like most process plants, your organization is
probably facing the dual challenges of maximiz­ing productivity while minimizing maintenance
costs. “Smart” digital transmitters offer superior
performance and reliability, while saving time and
effort in maintenance and calibration. Manufactur­ers of field instruments have helped accelerate the
changeover by offering smart transmitters at prices
nearly as low as analog units. As digital instru­ments using the HART protocol quickly become
the standard, communicators and calibrators are
becoming essential everyday tools.

What is HART?

HART, the Highway Addressable Remote Trans­ducer protocol, uses a 1200 baud Frequency Shift
Keying (FSK) signal to superimpose digital informa­tion on the conventional 4-20 mA analog signal.

Why use the HART protocol?

HART is an industry standard developed to define
the communications protocol between intelligent
field devices and a control system, HART is the
most widely used digital communication protocol
in the process industry. More than five million
HART field instruments are installed in more than
100,000 plants worldwide.

The HART protocol:

• Is supported by all of the major suppliers of
process field instruments supported by the HART
Communication Foundation, an industry-wide
non-profit organization. See the
http://www.hartcomm.org for information on the
HART standard.

• Preserves present control strategies.

• Allows traditional 4-20 mA signals and digital

communication to share the same two-wire
loops.

• Provides important information for installation
and maintenance: Tag IDs, measured values,
range and span data, product information and
diagnostics.

• Reduces operation costs by making it easier
to manage and fully utilize “smart” instrument
networks.

Fluke 789
ProcessMeter

The Fluke-789 doubles your power giving you a
multimeter and a loop calibrator in one tool.

Key 789 features:

• 24 V loop power supply

• HART mode setting with loop power

(adds 250 ohm resistor)

• 200 % larger dual display

• mA drive up to 1,200 ohms

• Enhanced backlight with (2) brightness settings

• Improved battery power with (4) AA batteries

• 0 % to 100 % mA Span Check buttons to toggle

from 4 mA to 20 mA

• Infrared I/O serial port compatible with
FlukeView Software

• 5 V measurement capability on the 4 V range
for precise 1 V to 5 V measurements

• DMM designed to meet 1000 V IEC 1010
CAT III standards

• Precision 1000 V, 400 mA digital multimeter
Measure ac and dc volts, ac and dc current,
resistance, continuity and frequency

• True-rms ac voltage measurement

• Frequency measurement to 20 kHz

• 20 mA dc current source/loop calibrator/simulator

Manual Step (100 %, 25 %, Coarse, Fine) plus
Auto Step and Auto Ramp

• Externally accessible battery for easy battery
changes

• V overload protection on V, ohms, frequency, mA
(backed up by 440 mA 1000 V fuse)

™

6 Fluke Corporation 750 Series Brochure

Automatically record and document your work

Fluke 750SW DPC/TRACK 2 software includes an
instrumentation data-base that makes it easy to manage
your instrumentation, create and schedule tests, load
and unload the 753 or 754, print a variety of standard
reports, and manage calibration data.

Print standard reports automatically. The software
assembles pre-formatted reports from your database
files, saving time and reducing errors. Reports include
calibration certificates, instruments due for calibration,
inventory characteristics, calibration histories, calibration
procedures, and traceability to instruments touched.

Documentation of results

The scheduling of calibrations, creation of procedures
and documentation of your calibration results are
facilitated by a number of instrumentation management
software packages:

Fluke DPC/TRACK

AMS from Emerson Process
Management, (formerly
Fisher-Rosemount).

All trademarks are the property of their respective holders.

To see the Fluke 750 Series calibrators in action,
call 1 800 44 FLUKE (U.S.), 31 40 2 675 200 (Europe),
1 425 446 5500 (other countries), or your local
Fluke representative for a demo. Visit our Web site:
www.uke.com/Processtools

™

PRM (Plant Resource
Manager) from Yokogawa
Electric Corporation.

On Time Support
Process/Track

The Fluke-C799 Field soft case is
included with every 750 series
documenting process calibrator. This
unique case has many useful features
that allow the calibrator to be operated
inside the case:

• Clear window protects from the
elements but allows access of
75X keyboard

• Input/output slot; bring test leads
from inside the case to connect to
what you are testing.

• Open the side pockets to connect
a pressure module

• Ample storage for a pressure
module, hand pumps all test leads
and interconnect cables.

7 Fluke Corporation 750 Series Brochure

Measurement function specifications

Condence Interval: k =3

DC voltage measurement

Accuracy (% of reading + floor)
Range (full scale) 1 year 2 years

100.000 mV 0.02 % + 0.005 mV 0.03 % + 0.005 mV

3.00000 V 0.02 % + 0.00005 V 0.03 % + 0.00005 V

30.0000 V 0.02 % + 0.0005 V 0.03 % + 0.0005 V

300.00 V 0.05 % + 0.05 V 0.07 % + 0.05 V

Temperature coefficient: (0.001 % reading + 0.0002 % range)/°C
from -10 °C to 18 °C and 28 °C to 50 °C, 100.000 mV range: 0.001 % of
reading + 0.001 % of range

Input impedance: >4 MΩ
Maximum input voltage: 300 V rms
Normal mode rejection: >100 dB at 50 Hx or 60 Hx nominal
Specifications are valid to 110 % of range (except for 300 V range)

AC voltage measurement

Range
40 Hz to 500 Hz

3.000 V 0.001 V .5 % + 0.002 V 1.0 % + 0.004 V

30.00 V 0.01 V 0.5 % + 0.02 V 1.0 % + 0.04 V

300.0 V 0.1 V 0.5 % + 0.2 V 1.0 % + 0.2 V

Input impedance: >4 M Ω and <100 pF
Input coupling: AC
Maximum input voltage: 300 V, IEC 61010 300V CAT II
Temperature coefficient: 5 % of specified accuracy / °C (<18 °C or >28 °C)
Specifications apply for 9 % to 100 % of voltage range.

Resolution % of reading + floor

1 year 2 year

DC current measurement

Accuracy (% of reading + floor)
Range (full scale) 1 year 2 years

30.000 mA 0.01 % + 5 uA 0.015 % + 7 uA

110.00 mA 0.01 % + 20 uA 0.015 % + 30 uA

Temperature coefficient: (3 % of specified accuracy)/°C from -10 °C to 18 °C
and 28 °C to 50 °C
Normal mode rejection: 90 dB at 50 or 60 Hz nominal and 60 dB at 1200 Hz
and 2200 Hz (HART signals)

Resistance measurement

Accuracy (% of reading + ohms)
Range (full scale) 1 year 2 years

10.000 Ω 0.05 % + 50 mΩ 0.07 % + 70 mΩ

100.00 Ω 0.05 % + 50 mΩ 0.07 % + 70 Ω

1.0000 kΩ 0.05 % + 0.5 Ω 0.07 % + 0.5 Ω

10.000 kΩ 0.1 % + 10 Ω 0.15 % + 15 Ω

Temperature coefficient: (3 % of specified accuracy)/°C from -10 °C to 18 °C
and 28 °C to 50 °C

Maximum input voltage: 50 V dc
Continuity: Continuous tone < 25 Ω, No tone > 400 Ω
Specifications are valid to 110 % of range

Frequency measurement

Resolution Accuracy

1

Range

2 years

1.00 Hz to 110.00 Hz 0.01 Hz 0.05 Hz

110.1 Hz to 1100.0 Hz 0.1 Hz 0.5 Hz

1.101 kHz to 11.000 kHz 0.001 kHz 0.005 kHz

11.01 kHz to 50.00 kHz 0.01 kHz 0.05 kHz

1

For frequencies < 109.99 Hz, specification applies for signals with slew rates > 5 V/ms
Minimum amplitude for Hz measurement: (Squarewaves) 1 Hz to
1 kHz, 300 mV p-p; 1 kHz to 30 kHz, 1.4 V p-p; > 30 kHz, 2.8 V p-p

Maximum input: 1 Hz to 1 kHz, 300 V rms; > 1 kHz, 30 V rms
Input impedance: 4 MΩ

Sourcing (simulation) function specifications

Condence Interval: k =3

DC voltage output

Accuracy (% of output + floor)
Range (full scale) 1 year 2 years

100.000 mV 0.01 % + 0.005 mV 0.015 % + 0.005 mV

1.00000 V 0.01 % + 0.00005 V 0.015 % + 0.0005 V

15.0000 V 0.01 % + 0.0005 V 0.015 % + 0.0005 V

Temperature coefficient: (0.001 % output + 0.001 % f.s.)/°C
from -10 °C to 18 °C and 28 °C to 50 °C

Maximum output current: 10 mA
Specifications are valid to 110 % of range, 100 mV and 1 V ranges

DC current output

Accuracy (% of output + floor)
Range (full scale) 1 year 2 years

22.000 mA 0.01 % + 0.003 mA 0.02 % + 0.003 mA
Current sink (sim- 0.02 % + 0.007 mA 0.04 % + 0.007 mA

ulate transmitter)

Specification applies from 0.1 mA to 22 mA; below 2 mA typical accuracy is

0.15 % of full scale

Maximum burden voltage: 18 V
Temperature coefficient: 3 % of specified accuracy/°C from -10 °C to 18 °C

and 28 °C to 50 °C

8 Fluke Corporation 750 Series Brochure

Resistance sourcing

Accuracy (% of output + ohms)
Range 1 year 2 years

10.000 Ω 0.01 % + 10 mΩ 0.015 % + 15 mΩ

100.00 Ω 0.01 % + 20 mΩ 0.015 % + 30 mΩ

1.0000 kΩ 0.02 % + 0.2 Ω 0.03 % + 0.3 Ω

10.000 kΩ 0.02 % + 3 Ω 0.03 % + 5 Ω

Temperature coefficient: 0.01 % f.s./°C from -10 °C to 18 °C and 28 °C to 50 °C
Maximum and minimum current through source resistance:

Maximum Minimum
10 Ω range: 10 mA dc 0.1 mA dc
100 Ω range: 10 mA dc 0.1 mA dc

1.0 kΩ range: 1 mA dc 0.01 mA dc
10 kΩ range: 1 mA dc 0.01 mA dc

Specifications valid to 110 % of range

Frequency sourcing

Range Specification

Sinewave: 0.1 Hz to 10.99 Hz 0.01 Hz
Squarewave: 0.01 Hz to 10.99 Hz 0.01 Hz
Sine and square 11.00 Hz to 109.99 Hz 0.1 Hz
Sine and square 110.0 Hz to 1099.9 Hz 0.1 Hz
Sine and square 1.100 kHz to 21.999 kHz 0.002 kHz
Sine and square 22.000 kHz to 50.000 kHz 0.005 kHz

Waveform choices: Zero-symmetric sine wave or positive 50 % duty-cycle square wave
Square wave amplitude: 0.1 V to 15 V p-p
Square wave amplitude accuracy:

0.01 kHz to 1 kHz: 1 % p-p output + 75 mV,
1 kHz to 50 kHz: 10 % p-p output + 75 mV

Sine wave amplitude: 0.1 V to 30 V p-p
Sine wave amplitude accuracy, 0.1 Hz to 50 kHz: 3 % p-p output + 75 mV
Maximum input voltage: ± 30 V dc

2 years

Temperature measurement and

simulation specifications

Condence Interval: k =3

Temperature, Resistance Temperature Detectors1

Degrees or % of reading

Type (α)

100 Ω Pt (385) -200 to 100 0.07 °C 0.14 °C 1 mA 0.05 °C 0.10 °C 0.1 mA to 10 mA

200 Ω Pt (385) -200 to 100 0.07 °C 0.14 °C 500 µA 0.06 °C 0.12 °C 0.1 mA to 1 mA

500 Ω Pt (385) -200 to 100 0.07 °C 0.14 °C 250 µA 0.06 °C 0.12 °C 0.1 mA to 1 mA

1000 Ω Pt (385) -200 to 100 0.07 °C 0.14 °C 150 µA 0.06 C 0.12 C 0.1 mA to 1 mA

100 Ω Pt (3916) -200 to 100 0.07 °C 0.14 °C 1 mA 0.05 °C 0.10 °C 0.1 mA to10 mA

100 Ω Pt (3926) -200 to 100 0.08 °C 0.16 °C 1 mA 0.05 °C 0.10 °C 0.1 mA to 10 mA

10 Ω Cu (427) -100 to 260 0.2 °C 0.4 °C 3 mA 0.2 °C 0.4 °C 1 mA to 10 mA
120 Ω Ni (672) -80 to 260 0.1 °C 0.2 °C 1 mA 0.04 °C 0.08 °C 0.1 mA to 10 mA

1

Specifications are valid to k=3

Sensor inaccuracies not included

2

For two and three-wire RTD measurements, add 0.4°C to the specifications.

Resolution: 0.01 °C except 0.1 °C for 10 Ω Cu (427)
Temperature coefficient: 0.02 °C/°C source, (<18°C or >28°C), 0.01 °C/C for measure
Maximum input voltage: 30 V

3

Supports pulsed transmitters and PLCs with pulse times as short as 1 ms

RTD reference: Pt(385): IEC 60751, 2008; (3916): JIS C 1604, 1981 ; Pt(3926), Cu(427), Ni(672): Minco Application Aid #18

Range °C Measure °C

1 year 2 years 1 year 2 years

100 to 800 0.02 % + 0.05 °C 0.04 % + 0.10 °C 0.0125 % + 0.04 °C 0.025 % + 0.08 °C

100 to 630 0.02 % + 0.05 °C 0.04 % + 0.10 °C 0.017 % + 0.05 °C 0.034 % + 0.10 °C

100 to 630 0.02 % + 0.05 °C 0.04 % + 0.10 °C 0.017% + 0.05 °C 0.034 % + 0.10 °C

100 to 630 0.02 % + 0.05 °C 0.04% + 0.10 °C 0.017 % + 0.05 °C 0.034 % + 0.10 °C

100 to 630 0.02 % +0.05 °C 0.04 % +0.10 °C 0.0125 % + 0.04 °C 0.025 % + 0.08 °C

100 to 630 0.02 % +0.06 °C 0.04 % +0.12 °C 0.0125 % + 0.04 °C 0.025 % + 0.08 °C

2

Temperature, Thermocouples

Type Source °C Measure °C Source °C

1 year 2 years 1 year 2 years

E -250 to -200 1.3 2.0 0.6 0.9

-200 to -100 0.5 0.8 0.3 0.4

-100 to 600 0.3 0.4 0.3 0.4
600 to 1000 0.4 0.6 0.2 0.3

N -200 to -100 1.0 1.5 0.6 0.9

-100 to 900 0.5 0.8 0.5 0.8
900 to 1300 0.6 0.9 0.3 0.4

J -210 to -100 0.6 0.9 0.3 0.4

-100 to 800 0.3 0.4 0.2 0.3
800 to 1200 0.5 0.8 0.3 0.3

K -200 to -100 0.7 1.0 0.4 0.6

-100 to 400 0.3 0.4 0.3 0.4
400 to 1200 0.5 0.8 0.3 0.4

1200 to 1372 0.7 1.0 0.3 0.4

T -250 to -200 1.7 2.5 0.9 1.4

-200 to 0 0.6 0.9 0.4 0.6
0 to 400 0.3 0.4 0.3 0.4

B 600 to 800 1.3 2.0 1.0 1.5

800 to 1000 1.0 1.5 0.8 1.2

1000 to 1820 0.9 1.3 0.8 1.2

R -20 to 0 2.3 2.8 1.2 1.8

0 to 100 1.5 2.2 1.1 1.7

100 to 1767 1.0 1.5 0.9 1.4

S -20 to 0 2.3 2.8 1.2 1.8

0 to 200 1.5 2.1 1.1 1.7

200 to 1400 0.9 1.4 0.9 1.4

1400 to 1767 1.1 1.7 1.0 1.5

C 0 to 800 0.6 0.9 0.6 0.9

800 to 1200 0.8 1.2 0.7 1.0
1200 to 1800 1.1 1.6 0.9 1.4
1800 to 2316 2.0 3.0 1.3 2.0

L -200 to -100 0.6 0.9 0.3 0.4

-100 to 800 0.3 0.4 0.2 0.3
800 to 900 0.5 0.8 0.2 0.3

U -200 to 0 0.6 0.9 0.4 0.6

0 to 600 0.3 0.4 0.3 0.4

9 Fluke Corporation 750 Series Brochure

Source
current

Type Source °C Measure °C Source °C

BP 0 to 1000 1.0 1.5 0.4 0.6

1000 to 2000 1.6 2.4 0.6 0.9
2000 to 2500 2.0 3.0 0.8 1.2

XK -200 to 300 0.2 0.3 0.2 0.5

300 to 800 0.4 0.6 0.3 0.6

Sensor inaccuracies not included.
Accuracy with external cold junction; for internal junction add 0.2 °C
Resolution: 0.1 °C
Temperature scale: ITS-90 or IPTS-68, selectable (90 is default)
Compensation: ITS-90 per NIST Monograph 175 for B,R,S,E,J,K,N,T; IPTS-68

per IEC 584-1 for B,R,S,E,J,K,T; IPTS-68 per DIN 43710 for L,U. GOST P 8.585­2001 for BP and XK, ASTM E988-96 for C (W5Re/W26Re)
Temperature coefficient: 0.05°C/°C (<18°C or >28°C)

0.07°C/°C for C type > 1800°C and for BP type > 2000°C
Instrument operating temperature: 0 °C to 50 °C for C and BP type
thermocouples / -10 °C to 50°C for all other types
Normal mode rejection: 65 dB at 50 Hz or 60 Hz nominal

Source °C Allowable

1 year 2 years 1 year 2 years

current

3

Why you can depend on Fluke calibrator specifications

Specifications must be carefully considered when comparing calibrators from
different vendors.

For example, Fluke specifications use a 3-sigma confidence interval
(k = 3). This means that 99.7 % of measurements will remain in specifi­cation over the stated period of time. Other manufacturers use a 2-sigma
confidence interval (k = 2). This means that 95.4 % of measurements will
remain in specification over the stated period of time so one in 20 instru­ments are statistically likely to fail to perform to their specifications.

The most important components of a process calibrator specification are:

• Reference uncertainty. Performance of a calibrator at 23 °C + 3 °C at

the time it is verified by the manufacturer. This specification does not
include the effects of time and temperature, two of the largest
components of calibrator error.

• Time. Fluke 750 Series calibrators are delivered with both one-year

and two-year specs, to limit your calibration support costs. You choose
your cal interval based upon the performance you need.

• Temperature. Fluke process calibrator specs reflect performance from

18 °C to 28 °C. Compensation factors are provided to permit specified
use of the calibrators over a wide -10 °C to 50 °C range.

• Allowance for traceability. Fluke specs are not relative specs,

but total specs, including an allowance for uncertainty of standards
that provide traceability to national standards.

For more information, view our interpreting specifications webinar or refer to the
application note “Understanding Specifications For Process Calibrators.”

Pressure specifications

The Fluke family of 29 pressure modules:

Covers virtually any pressure application including
gage, differential, dual (compound), absolute, and
vacuum.

Display pressure readings in any of ten different

•

pressure units you specify in the calibrator setup.

Rugged urethane molded cases protect the modules

•

from rough handling and harsh conditions.

Features internal temperature compensation from

•

O °C to 50 °C for full-accuracy performance.

Includes NIST-traceable calibration certificate.

•

Modules can be calibrated locally, helping to

•

control costs.

Pressure module specifications (all specifications in % of full span. Specifications reflect a confidence interval of 95 %.)

Reference High2 Low
Range/ Range (approx)/ uncertainty Stability Temperature Total
Model Resolution Resolution (23 ± 3 ºC) (1 year) (0 to 50 ºC) uncertainty media media material (x nominal)

Differential

FLUKE-700P00 1 in. H
FLUKE-700P01 10 in. H
FLUKE-700P02 1 psi/0.0001 6900 Pa/0.7 0.150 0.070 0.080 0.300 Dry Dry 316 SS 3x
FLUKE-700P22 1 psi/0.0001 6900 Pa/0.7 0.100 0.020 0.030 0.150 316 SS Dry 316 SS 3x
FLUKE-700P03 5 psi/0.0001 34 kPa/0.001 0.050 0.020 0.030 0.100 Dry Dry 316 SS 3x
FLUKE-700P23 5 psi/0.0001 34 kPa/0.001 0.025 0.010 0.015 0.050 316 SS Dry 316 SS 3x
FLUKE-700P04 15 psi/0.001 103 kPa/0.01 0.025 0.010 0.015 0.050 Dry Dry 316 SS 3x
FLUKE-700P24 15 psi/0.001 103 kPa/0.01 0.025 0.010 0.015 0.050 316 SS Dry 316 SS 3x

Gage

FLUKE-700P05 30 psi/0.001 207 kPa/0.01 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700P06 100 psi/0.01 690 kPa/0.07 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700P27 300 psi / 0.01 2070 kPa / 0.1 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700P07 500 psi/0.01 3400 kPa/0.1 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700P08 1000 psi/0.1 6900 kPa/0.7 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700P09 1500 psi/0.1 10 MPa/0.001 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 2x

Absolute (not compatible with Fluke 701 or 702)

FLUKE-700PA3 5 psi/0.0001 34 kPa/0.001 0.050 0.010 0.010 0.070 316 SS N/A 316 SS 3x
FLUKE-700PA4 15 psi/0.001 103 kPa/0.01 0.050 0.010 0.010 0.070 316 SS N/A 316 SS 3x
FLUKE-700PA5 30 psi/0.001 207 kPa/0.01 0.050 0.010 0.010 0.070 316 SS N/A 316 SS 3x
FLUKE-700PA6 100 psi/0.01 690 kPa/0.07 0.050 0.010 0.010 0.070 316 SS N/A 316 SS 3x

Vacuum (not compatible with Fluke 701 or 702)

FLUKE-700PV3 -5 psi/0.0001 -34 kPa/0.001 0.040 0.015 0.015 0.070 316 SS Dry 316 SS 3x
FLUKE-700PV4 -15 psi/0.001 -103 kPa/0.01 0.040 0.015 0.015 0.070 316 SS Dry 316 SS 3x

Dual

FLUKE-700PD2 ±1 psi/0.0001 ±6900 Pa/0.7 0.150 0.025 0.025 0.200 316 SS Dry 316 SS 3x
FLUKE-700PD3 ±5 psi/0.0001 ±34 kPa/0.001 0.040 0.015 0.015 0.070 316 SS Dry 316 SS 3x
FLUKE-700PD4 ±15 psi/0.001 ±103 kPa/0.01 0.025 0.010 0.015 0.050 316 SS Dry 316 SS 3x
FLUKE-700PD5 -15/30 psi/0.001 -100/207 kPa/0.01 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700PD6 -15/100 psi/0.01 -100/690 kPa/0.07 0.025 0.010 0.015 0.050 316 SS N/A 316 SS 3x
FLUKE-700PD7 -15/200 psi/0.01 -100/1380 kPa/0.1 0.040 0.015 0.015 0.070 316 SS N/A 316 SS 3x

High

FLUKE-700P29 3000 psi/0.1 20.7 M Pa/0.001 0.050 0.010 0.020 0.080 C276 N/A C276 2x
FLUKE-700P30 5000 psi/0.1 34 M Pa/0.001 0.050 0.010 0.020 0.080 C276 N/A C276 2x
FLUKE-700P31 10000 psi/1 69 M Pa/0.007 0.050 0.010 0.020 0.080 C276 N/A C276 1.5x

1

Total uncertainty, one year for temperature range 0 °C to +50 °C. Total uncertainty, 1.0% of full span for temperature range -10 °C to 0 °C. For P00 module only, compensated

temperature range is 15 ° to 35 °C.

2

“Dry” indicates dry air or non-corrosive gas as compatible media. “316 SS” indicates media compatible with Type 316 Stainless Steel. “C276” indicates media compatible with

Hastelloy C276.

Use of pressure zero is required prior to measurement or source. Maximum overpressure specification includes common mode pressure. Modules are
1/4˝ NPT female to male BSP/ISO 1/4-19, tapered thread, included with all modules except P29, P30, and P31. Effective October 1996, all modules include a NIST traceable certificate
and test data.

O/0.001 0.25 kPa/0.0002 0.300 0.025 0.025 0.350 Dry Dry 316 SS 30x

2

O/0.01 2.5 kPa/0.002 0.200 0.050 0.050 0.300 Dry Dry 316 SS 3x

2

1

side side Fitting pressure

2

rated. Metric adapter(s):

Max over-

10 Fluke Corporation 750 Series Brochure

General specications

Data log function

Measure functions: Voltage, current, resistance,
frequency, temperature, pressure
Reading rate: 1, 2, 5, 10, 20, 30, or 60 readings
per minute
Maximum record length: 8000 readings
(7980 for 30 or 60 readings per minute)

Ramp function

Source functions: Voltage, current, resistance,
frequency, temperature

Rate: 4 steps/second
Trip detect: Continuity* or voltage

*Continuity detection not available when sourcing current

Loop power function

Voltage: 26 V
Accuracy: 10 %, 18 V minimum at 22 mA
Maximum current: 25 mA, short-circuit protected
Maximum input voltage: 50 V dc

Note: 250 Ω series resistance is automatically supplied whenever loop power is
enabled on 754.

HART modem interface (754 only)

Maximum input voltage: 30 V dc

Environmental specifications

All calibrator specifications apply from +18 °C to
+28 °C unless stated otherwise.

Operating temperature: -10 °C to 50 °C
Storage temperature: -20 °C to 60 °C
Operating altitude: 3000 m above mean sea level

(9842 ft)
90-day specifications: The standard specification
intervals for the 750 Series are 1 and 2 years.
Typical 90-day measurement and source accuracy can
be estimated by dividing the one year “% of reading”
or “% of output” specifications by 2. Floor specifications,
expressed as “% of f.s.” or “counts” or “ohms” remain
constant.

Ingress protection:

IP-52

Power: Internal battery pack li-ion, 7.2 V, 4400 mAh,
30 Wh; Battery life: Typical usage, >8 hours
Dimensions: 136mm x 245mm x 63 mm
(5.4 in x 9.6 in x 2.5 in)

Weight: 1.2 kg (2.7 lb)
Side port connections:

• Pressure module connector

• USB connector to interface to your PC

• Digital instrument (HART) connector

• Connection for optional battery charger/eliminator

Safety: Complies with CAN/CSA C22.2 No 1010.1-92,
ANSI/ISA S82.01-1994, UL3111, and EN610-1:1993.
Data storage capacity:

1 week of calibration procedures and results

11 Fluke Corporation 750 Series Brochure

Ordering information

FLUKE-753 Documenting Process Calibrator
FLUKE-754 Documenting Process Calibrator-HART

Standard accessories include: Three sets of stackable
test leads, three sets of TP220 test probes with three
sets of “extended tooth” alligator clips, two sets AC280
hook clips, BP7240 Li-ion battery pack, BC7240 battery
charger, C799 field soft case, USB communication cable,
getting started guide, instruction manual on CDROM,
NIST traceable certificate of calibration, DPC/TRACK 2
sample software that enables upload and printing of
calibration records. Model Fluke-754 includes HART
communication cable. Includes C799 Field Soft Case.
Includes three year warranty.

FLUKE-750SW DPC/TRACK 2 Software

Included with DPC/TRACK software:
Software media, Instruction Manual, USB Cable.

FLUKE-700 Pxx Pressure Modules

Included with each Fluke Pressure Module:
BP-ISO Adapter(s) (except with P29 - P31), Instruction
Sheet, NIST traceable calibration report and data,
one-year warranty.

Accessories

Fluke-700PMP Pressure Pump; 100 psi/7 bar
Fluke-700LTP-1 Low Pressure Test Pump
Fluke-700PTP-1 Pneumatic Test Pump;

400 psi/40 bar
Fluke-700HTP-1 Hydraulic Test Pump;
10,000 psi/700 bar

Fluke-700HTH-1 Hydraulic Test Hose
Fluke-700PRV-1 Pressure Relief Valve Kit for HTP
Fluke-700-IV Current Shunt (for mA/mA

applications)

Fluke-700PCK Pressure Calibration Kit
Fluke-700TC1 TC Mini-Plug Kit, 9 types
Fluke-700TC2 TC Mini-Plug Kit, JKTERS
Fluke-700TLK Process Test lead kit
754HCC Smart instrument

communication cable

BC7240 Battery Charger
BP7240 Li-on Battery Pack
C700 Hard Carrying Case
C781 Soft Carrying Case
C799 Soft Field Case

Fluke. Keeping your world up and running.

Fluke Corporation
PO Box 9090,
Everett, WA 98206 U.S.A.

For more information call:
In the U.S.A. [phone] or Fax [phone]
In Europe/M-East/Africa [phone] or Fax [phone]
In Canada (800)-36-FLUKE or Fax [phone]
From other countries [phone] or Fax [phone]
Web access: http://www.fluke.com

©2004-2011 Fluke Corporation. Specifications subject to change without notice.
Printed in U.S.A. 9/2011 1263323L B-EN-N

Modification of this document is not permitted without written permission from
Fluke Corporation.

Fluke Europe B.V.

PO Box 1186, 5602 BD
Eindhoven, The Netherlands

®