Atec Agilent-E5515C User Manual

Agilent E5515C Wireless Communications Test Set
High performance hardware platform for the 8960 family of mobile device design and manufacturing test solutions
The only bench top test set hardware platform with performance for mobile device test across the entire lifecycle – from design through integration/validation, conformance, manufacturing and repair.
The high performance E5515C is the hardware platform for the 8960 wireless communications test set family. Combining the E5515C with software from the 8960 family of embedded software applications creates a cellular network emulator for testing mobile device RF, baseband and IP data traffic flows. Testing can be done via call processing or test mode control and provides:
Industry’s most accurate, repeatable standards-compliant RF and baseband measurements
Stable performance for end-to-end high speed IP data throughput testing
Industry leading accuracy, reliability and measurement speed
The 8960 with E5515C speeds mobile device development, increases manufacturing throughput and minimizes support costs.
Test performance specifications are documented in the software applications. Refer to www.agilent.com/find/8960 for available software applications.
One test set for design, integration/validation, conformance, and manufacturing test
Using one test set across the design cycle speeds design and manufacturing by providing faster and simpler debug and fix cycles, easier problem replication across groups, higher asset utilization, and reduced support requirements.
The 8960 hardware platform consists of the E5515C base-model and three hardware functionality options:
Option 002 – Second RF source for GSM, GPRS and EGPRS
technologies.
Option 003 – Flexible CDMA base station emulator for today’s CDMA-based technologies such as cdma2000, 1xEV-DO, W-CDMA, HSPA and HSPA+. Also needed for some GSM, GPRS and EGPRS features.
Option 004 – Digital Bus option for fading test solutions with Agilent’s N5115/5101 Baseband Studio applications
2
Technical Specifications
These specifications apply to an E5515C mainframe for serial number US40410101, GB4041010, MY46010000 or higher.
Specifications describe the test set’s warranted performance and are valid for the unit’s operation within the stated environmental range unless otherwise noted. All specifications are valid after a 30-minute warm-up period of continuous operation.
Supplemental characteristics are intended to provide typical, but non-warranted, performance parameters that may be useful in applying the instrument. These characteristics are shown in italics and labeled as “typical”, or “supplemental.” All units shipped from the factory meet these typical numbers at 25 °C ambient temperature without including measurement uncertainty.
These are general specifications that apply to an E5515C mainframe over the 25 °C ±5 °C ambient temperature range. Specific test and lab application specifications can be found in the library on the 8960 website: www.agilent.com/find/8960
Remote programming
GPIB IEEE Standard 488.2 GPIB help pressing the front panel Help key and then any other
key will cause the test set to display the GPIB syntax for that command at the bottom of the front panel display; pressing the Help key again exits this mode of operation
Remote front panel lockout allows remote user to disable the front panel display
to improve GPIB measurement speed
Implemented functions T6, TE0, L4, LE0, SH1, AH1, RL1, SR1, PP0, DC1, DT0,
C0, and E2
General specifications
Dimensions (H x W x D) 8.75 x 16.75 x 24.63 inches (222 x 426 x 625 mm), 7
rack spaces high Weight 66 lbs (30 kg) Display 10.5 inches (26.7 cm), active matrix, color, liquid crystal LAN (local area network) port (for firmware upgrades and protocol logging only) Operating temperature 0 to +55 °C Storage temperature 20 to +70 °C Power 100 to 240 Vac, 50 to 60 Hz, 550 VA maximum Calibration interval two years EMI conducted and radiated interference meets CISPR-11
Radiated leakage due to RF generator
Spurious leakage typically < 5 μV induced in a resonant dipole antenna
Power consumption typically 400 to 450 W continuous
RJ-45 connector, 10 base T Ethernet with TCP/IP
support
typically < 1 μV induced in a resonant dipole antenna
one inch from any surface except the underside and
rear panel at set RF generator output frequency and
output level of 40 dBm
one inch from any surface on the front half of all sides
of the instrument at frequencies other than the RF
generator output frequency and output level of −40
dBm with no cable connected to the rear-panel LAN
port
3
www.agilent.com www.agilent.com/find/8960
For more information on Agilent Technologies’ products, applications or services, please contact your local Agilent office. The complete list is available at:
www.agilent.com/find/contactus
Americas
Canada Latin America United States Asia Pacific Australia China Hong Kong India Japan Korea Malaysia Singapore Taiwan Thailand
Europe & Middle East
Austria Belgium Denmark Finland France
Germany Ireland Israel Italy Netherlands Spain Sweden Switzerland United Kingdom Other European Countries: www.agilent.com/find/contactus
Revised: October 1, 20 08
Product specification and descriptions in this document subject to change without notice.
© Agilent Technologies, Inc. 2008 Printed in USA, November 12, 2008 5990-3238EN
(877) 894-4414 305 269 7500 (800) 829-4444
1 800 629 485 800 810 0189 800 938 693 1 800 112 929 0120 (421) 345 080 769 0800 1 800 888 848 1 800 375 8100 0800 047 866 1 800 226 008
01 36027 71571 32 (0) 2 404 93 40 45 70 13 15 15 358 (0) 10 855 2100 0825 010 700*
*0.125 €/minute
07031 464 6333 1890 924 204 972-3-9288-504/544 39 02 92 60 8484 31 (0) 20 547 2111 34 (91) 631 3300 0200-88 22 55 0800 80 53 53 44 (0) 118 9276201
4
Loading...