Atec Agilent-6570A User Manual

Agilent 6570A Series Single-Output, 2000 W DC Power Supplies
Data Sheet
Speed and accuracy for test optimization
• Front panel and analog control of output voltage and current
• Fast, low-noise outputs
• Fan-speed control to minimize acoustic noise
• Protection features to ensure DUT safety
This series of 2000 watt DC power supplies has the exceptional, proven reliability that test system engineers look for. It also has the unusual combination of high efficiency and low noise operation.
These DC power supplies can be controlled either from the front panel or via an analog programming voltage. When used in a test system, the fast up and down programming helps decrease test time. Quickly reacting protection features, including CV/CC mode crossover and over-voltage protection help protect your valuable assemblies from damage.
Lab-bench use is enhanced by the fan-speed control, which minimizes acoustic noise. The extremely low ripple and noise helps the test engineer make extremely accurate current and voltage measurements.
Specifi cations
Specifications
(at 0 ° to 55 °C unless otherwise specified)
Number of outputs 1 1 1 1 1 1
GPIB No No No No No No
Output ratings
Output voltage 0 to 8 V 0 to 20 V 0 to 35 V 0 to 60 V 0 to 120 V 14 V
Output current 0 to 220 A 0 to 100 A 0 to 60 A 0 to 35 A 0 to 18 A 150 A
Programming accuracy (at 25 °C ± 5 °C)
Voltage 0.04% + 8 mV 20 mV 35 mV 60 mV 120 mV 14 mV
Current 0.1% + 125 mA 60 mA 40 mA 25 mA 12 mA 90 mA
Ripple and noise from 20 Hz to 20 MHz
Voltage rms 650 μV 750 μV 800 μV 1.25 mV 1.9 mV 1.5 mV
peak-to-peak 7 mV 9 mV 9 mV 11 mV 16 mV 15 mV
Current rms 200 mA 100 mA 40 mA 25 mA 12 mA 150 mA
Load and line regulation
Voltage 0.002% + 300 μV 650 μV 1.2 mV 2 mV 4 mV 600 μV
Current 0.005% + 10 mA 7 mA 4 mA 2 mA 1 mA 7 mA
Transient response time Less than 900 μs for the output voltage to recover to within 100 mV following a change
Supplemental characteristics
(Non-warranted characteristics determined by design and useful in applying the product)
Average programming resolution
Voltage 2 mV 5 mV 9 mV 15 mV 30 mV 4 mV
Current 55 mA 25 mA 15 mA 8.75 mA 4.5 mA 40 mV
OVP 15 mV 35 mV 65 mV 100 mV 215 mV 28 mV
Output voltage programming response time* (excluding command processing time)
6571A 6572A 6573A 6574A 6575A
in load from 100% to 50% or 50% to 100% of the output current rating of the supply
6571A 6572A 6573A 6574A 6575A
30 ms 60 ms 130 ms 130 ms 195 ms 30 ms
6571A-J03
Special order
option
6571A-J03
Special order
option
* Full load programming rise/fall time (10% to 90% or 90% to 10%) with full resistive load equal to rated output voltage/rated output current.
2
Specifi cations, continued
Specifications
(at 0 ° to 55 °C unless otherwise specified)
6571A-J04
Special order
option
6571A-J17
Special order
option
6573A-J03
Special order
option
6573A-J08
Special order
option
6574A-J03
Special order
option
6574A-J07
Special order
option
Number of outputs 1 1 1 1 1 1
GPIB No No No No No No
Output ratings
Output voltage 10 V 15 V 37.5 V 40 V 56 V 50 V
Output current 200 A 120 A 45 A 50 A 38 A 42 A
Programming accuracy (at 25 °C ± 5 °C)
Voltage 0.04% + 10 mV 15 mV 37.5 mV 40 mV 60 mV 60 mV
Current 0.1% + 125 mA 90 mA 40 mA 35 mA 28 mA 30 mA
Ripple and noise from 20 Hz to 20 MHz
Voltage rms 750 μV 1.5 mV 800 μV 1 mV 1.25 mV 1.25 mV
peak-to-peak 9 mV 15 mV 9 mV 10.5 mV 11 mV 11 mV
Current rms 200 mA 150 mA 40 mA 40 mA 28 mA 25 mA
Load and line regulation
Voltage 0.002% + 300 μV 650 μV 1.2 mV 1.4 mV 2 mV 2 mV
Current 0.005% + 10 mA 7 mA 4 mA 4 mA 2 mA 2 mA
Transient response time Less than 900 μs for the output voltage to recover to within 100 mV following a change in
load from 100% to 50% or 50% to 100% of the output current rating of the supply
Supplemental characteristics
(Non-warranted characteristics determined by design and useful in applying the product)
6571A-J04
Special order
option
6571A-J17
Special order
option
6573A-J03
Special order
option
6573A-J08
Special order
option
6574A-J03
Special order
option
6574A-J07
Special order
option
Average programming resolution
Voltage 2.5 mV 4 mV 10 mV 10.5 mV 14 mV 12 mV
Current 55 mA 35 mA 15 mA 12.5 mA 9.5 mA 11 mA
OVP 20 mV 30 mV 65 mV 75 mV 100 mV 85 mV
Output voltage programming
35 ms 35 ms 130 ms 130 ms 130 ms 130 ms response time* (excluding command processing time)
* Full load programming rise/fall time (10% to 90% or 90% to 10%) with full resistive load equal to rated output voltage/rated output current.
3
Specifi cations, continued
Specifications
(at 0 ° to 55 °C unless otherwise specified)
6575A-J04
Special order
option
6575A-J06
Special order
option
6575A-J07
Special order
option
6575A-J08
Special order
option
6575A-J09
Special order
option
6575A-J11
Special order
option
Number of outputs 1 1 1 1 1 1
GPIB No No No No No No
Output ratings
Output voltage 160 V 135 V 200 V 100 V 110 V 150 V
Output current 13 A 16 A 11 A 22 A 20 A 15 A
Programming accuracy (at 25 °C ± 5 °C)
Voltage 0.04% + 160 mV 125 mV 200 mV 120 mV 120 mV 150 mV
Current 0.1% + 10 mA 12 mA 8 mA 15 mA 13.5 mA 11 mA
Ripple and noise from 20 Hz to 20 MHz
Voltage rms 2.8 mV 2 mV 3.5 mV 1.9 mV 1.9 mV 2.5 mV
peak-to-peak 20 mV 18 mV 25 mV 16 mV 16 mV 18 mV
Current rms 18 mA 12 mA 15 mA 15 mA 13.5 mA 12 mA
Load and line regulation
Voltage 0.002% + 6 mA 4 mA 7 mA 4 mV 4 mV 6 mV
Current 0.005% + 1 mA 4 mA 1 mA 4 mA 4 mA 1 mA
Transient response time Less than 900 μs for the output voltage to recover to within 100 mV following a change in
load from 100% to 50% or 50% to 100% of the output current rating of the supply
Supplemental characteristics
(Non-warranted characteristics determined by design and useful in applying the product)
6575A-J04
Special order
option
6575A-J06
Special order
option
6575A-J07
Special order
option
6575A-J08
Special order
option
6575A-J09
Special order
option
6575A-J11
Special order
option
Average programming resolution
Voltage 40 mV 34 mV 50 mV 30 mV 30 mV 37.5 mV
Current 3.25 mA 4 mA 2.75 mA 4.5 mA 4.5 mA 3.75 mA
OVP 300 mV 242 mV 360 mV 215 mV 215 mV 270 mV
Output voltage programming
280 ms 250 ms 350 ms 195 ms 195 ms 250 ms response time* (excluding command processing time)
* Full load programming rise/fall time (10% to 90% or 90% to 10%) with full resistive load equal to rated output voltage/rated output current.
4
425.5 mm
16.75"
574 mm
22.6"
640 mm
25.4"
68 mm
2.67"
132.6 mm
5.2"
145.1 mm
5.71"
12.7 mm
0.5"
128 mm
5.04"
Accepts wire
AWG 12-22
1/4" x 1" untreaded hole on each bussbar
Note: Buss bar is 1/8" thick cu
1.25"
0.75"
0.31 dia"
1.0"
0.5"
IM VP
+IP
-IP +P +S
-S
-LS +LS
To p
Side
Rear
Rear connector detail
Buss bar detail
Supplemental characteristics for all model numbers
Modulation: (Analog programming of
output voltage and current)
Input signal: 0 to –4 V for voltage, DC floating voltage: Output terminals can be floated up to ± 240 VDC from
0 to 7 V for current
Input impedance: 30 kΩ or greater chassis ground
Input power: 3,800 VA, 2,600 W at full Output common-mode noise current:
load; 170 W at no load (to signal ground binding post) 500 μA rms, 4 mA peak-to-peak
Regulatory compliance: Listed to
UL1244; certified to CSA556B; conforms Remote sensing: Up to half the rated
to IEC 61010-1 output voltage can be dropped in each load lead. The drop in the load leads subtracts from the voltage available for the load.
Size:
425.5 mm W x 132.6 mm H x 640 mm D
(16.75 in x 5.22 in x 25.2 in)
Weight: Net, 28.2 kg (62 lb);
shipping, 31.8 kg (70 lb)
Warranty: One year
Agilent models: 6571A, 6572A, 6573A, 6574A, 6575A
5
www.agilent.com
s
www.agilent.com/find/6570
Ordering information
The 6570 Series power supplies come with full documentation on CD-ROM. The CD-ROM includes user’s guide, service manual, quick start guide, and application notes
Opt 200 174 to 220 VAC, 47 to 63 Hz (Japan only)
Opt 230 191 to 250 VAC, 47 to 63 Hz
Opt 0L1 Printed user’s guide Opt 0B3 Printed service manual
Accessories
1CM003A* Rack mount flange kit
132.6 mm H (3U) – two flange brackets 1CP002A* Rack mount flange and handle kit 132.6 mm H (3U) – two brackets and front handles E3663AC Support rails for Agilent rack cabinets
p/n 1494-0059 Accessory slide kit
Application notes
Agilent DC Power Supplies for Base Station Testing, 5988-2386EN
10 Practical Tips You Need to Know About Your Power Products,
5965-8239E
Agilent Advantage Services is committed to your success throughout your equip­ment’s lifetime. To keep you competitive, we continually invest in tools and processes that speed up calibration and repair and reduce your cost of ownership. You can also use Infoline Web Services to manage equipment and services more effectively. By sharing our measurement and service expertise, we help you create the products that change our world.
www.agilent.com/find/advantageservices
Agilent Electronic Measurement Group
DEKRA Certified
ISO 9001:2008
Quality Management SystemQuality Management Sy
www.agilent.com/quality
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the products and applications you select.
Agilent Channel Partners
www. agilent.com/find/channelpartners
Get the best of both worlds: Agilent’s measurement expertise and product breadth, combined with channel partner convenience.
For more information on Agilent Technologies’ products, applications or services, please contact your local Agilent office. The complete list is available at:
www.agilent.com/fi nd/contactus
Americas
Canada (877) 894 4414 Brazil (11) 4197 3600 Mexico 01800 5064 800 United States (800) 829 4444
Asia Pacifi c
Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 112 929 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 375 8100
Europe & Middle East
Belgium 32 (0) 2 404 93 40 Denmark 45 45 80 12 15 Finland 358 (0) 10 855 2100 France 0825 010 700*
*0.125 €/minute
Germany 49 (0) 7031 464 6333 Ireland 1890 924 204 Israel 972-3-9288-504/544 Italy 39 02 92 60 8484 Netherlands 31 (0) 20 547 2111 Spain 34 (91) 631 3300 Sweden 0200-88 22 55 United Kingdom 44 (0) 118 927 6201
For other unlisted countries:
www.agilent.com/fi nd/contactus
Revised: January 6, 2012
* Support rails required
Product specifications and descriptions in this document subject to change without notice.
© Agilent Technologies, Inc. 2012 Published in USA, March 26, 2012 5990-9300EN
Loading...