+15 to -49 dBm (1.26 Vrms to 793m Vrms: 2dBV to -62 dBV)
into a 50Ω load
0.1 dB
± 1 dB at +15 dBm and 100 kHz. Below +15 dBm, add the greater
of ± 0.02 dB/dB or 0.2 dB
1.5 dBp-p from 5 Hz to 200 MHz
50Ω; > 20 dB return loss at all levels
50Ω Type N female
Linear, alternate, cw and log frequency; log amplitude
100 ms/span to 200 ms/span for frequency sweep; 1 ms/step to 16
s/step for amplitude sweep
Continuous, single, manual
Free run, immediate, line, external
-13 dBV from 10 kHz to 200 MHz with internal 20 dB attenuators
ON (0dBm at 50Ω)
INPUT CHARACTERISTICS
Frequency Range
Inputs
Input Impedance
Input Connectors
Resolution Bandwidth
Sensitivity (Due to noise and
internal crosstalk between
source and receiver inputs)
5 Hz - 200 MHz
3 (A, B, R)
Selectable 50Ω with > 25 dB return loss, or 1 MΩ
approximately 30 pF
50Ω Type N female
Selectable 1 kHz, 100 Hz, 10 Hz, or 1 Hz
30 kHz - 200 MHz (50Ω)
Resolution
Bandwidth
30 kHz - 20 MHz (1 MΩ)
Internal 20 dB
Attenuator ON
Internal 20 dB
Attenuator OFF
1 Hz
Input Level Relative
Marker: 0.005 deg (0.001 rad)
10 Hz
100 Hz
1 kHz
-110 dBm
-110 dBm
-105 dBm
-95 dBm
-130 dBm
-130 dBm
-125 dBm
-115 dBm
Crosstalk
Electrical Length/Reference
Plane Extension
Resolution
Accuracy
> 100 dB isolation between inputs
Provides equivalent electrical line length, or delay at inputs A, B,
and R.
Range: -3 X 108 m to +3 X 108 m or +1 to -1 s
5 digits or 0.1 cm (3.3 Ps) whichever is greater
± 0.1 cm or ± 0.02% whichever is greater
MAGNITUDE CHARACTERISTICS
Range
Full Scale Input to Sensitivity
Marker: 0.002 dB (log); 5 digits (linear)
Resolution
Display Units
Accuracy
(at 100 kHz, 25°C, and Full Scale Input)
Absolute (A, B, R)
Ratio (A/R, B/R, A/B)
Display: 0.01 dB/div to 20 dB/div (log absolute); 0.01 dB/div to
200 dB/div (log ratio); 0.1 NV/div to 10 V/div (linear absolute);
-10
10
/div to 1020/div (linear ratio)
dB, DBMS, div, V, and linear ratio
± 0.2 dB
± 0.15 dB (50Ω); ± 0.2 dB (1 MΩ)
1 kHz, 100 Hz, 10 Hz
Error
Resolution Bandwidth
1 Hz
to Full Scale Input
Dynamic Accuracy
Frequency Response
(when driven from a 50Ω source and with a 50Ω receiver input impedance)
Absolute (A, B, R)
Ratio (A/R, B/R, A/B)
Reference Level
Stability
PHASE CHARACTERISTICS
Range
Resolution
± .04 dB
± .02 dB
± .05 dB
± .15 dB
± .75 dB
± .75 dB
± .04 dB
± .02 dB
± .05 dB
± .25 dB
± .75 dB
± 3.00 dB
0 dB to -10 dB
-10 dB to -50 dB
-50 dB to -60 dB
-60 dB to -80 dB
-80 dB to -90 dB
-90 dB to -100 dB
0.3 dBpp from 20 Hz to 20 MHz; 0.6 dBpp from 5 Hz to 200 MHz
0.3 dBpp from 20 Hz to 20 MHz; 0.4 dB from 5 Hz to 200 MHz
Range: -207 DBMS to +33 DBMS (-220 div to +20 div) (Log
absolute); -400 dB to +400 dB (log ratio); 0 V to 10 V (linear
absolute); 0 to 1020 (linear ratio)
Temperature: Typically <± 0.02 dB/°C
Time: Typically <± 0.05 dB/hour at 25°C
± 180 degrees
Display: 0.01 deg/div to 200 deg/div (0.00018 rad/div to 3.49
Input Level Relative
0% to 100% full scale deflection on 0.05% increments.
rad/div)
Accuracy (at 100 kHz, 25°C,
and Full Scale Input)
Dynamic Accuracy
Reference Level Resolution
Temperature Stability
Time Stability
POLAR DISPLAY
CHARACTERISTICS
Full Scale Magnitude Range
REAL, IMAGINARY
DISPLAY
CHARACTERISTICS
± 2.0°
Error
± .4 deg
± .2 deg
± .5 deg
± 1.5 deg
± 7.5 deg
to Full Scale Input
0 dB to -10 dB
-10 dB to -50 dB
-50 dB to -60 dB
-60 dB to -80 dB
-80 dB to -100 dB
0.01°
Typically <± 0.05 deg/°C
Typically <± 0.05°/hour at 25°C
Range, Resolution, Display Units, Dynamic Accuracy, Frequency
Response, Uncertainty, Crosstalk, Reference Level, and Stability
specifications are the same as the corresponding magnitude and
phase characteristics.
Absolute (A, B, R): 0.1 nV to 10 V
Ratio (A/R, B/R, A/B): 10
-10
to 1020
Range, Dynamic Accuracy, Frequency Response, Uncertainty,
Crosstalk, Stability specifications are the same as the
corresponding magnitude and phase characteristics.
DELAY CHARACTERISTICS
Range
Resolution
Normalized Accuracy
Aperture Range
Reference Level
1 ps to 20,00s
.01ns/div to 1000s/div
Dynamic Phase Accuracy +2nS
360 X Aperture [Hz]
0.5% to 16% of frequency span
± 103 S
GENERAL DISPLAY CHARACTERISTICS
Traces
Two simultaneous traces may be present with a rectangular
graticule. One trace with polar or Smith graticules.
Markers: Each trace has one main marker and an offset marker.
No. Traces
Markers indicate data at corresponding trace coordinates in the
same units as used to set the Reference Level. Markers can be
used to modify certain display parameters. Marker resolution is
the same as horizontal display function.
Graticules
Rectangular Graticule
Logarithmic and Linear.
Polar/Smith Chart Graticule
Noise Averaging
Type
Averaging Factor
Linear Phase Slope
Compensation
Calibration
Transmission
Reflection
PROGRAMMING CHARACTERISTICS
Capability
Interface Functions
Output Data Transfer Time
± 500 deg in 0.001 deg increments
Exponentially weighted vector averaging on successive sweep data
Selectable 1 (off), 4, 8, 16, 32, 64, 128, 256
Provides linear phase slope offset of -72,000 deg/span to +72,000
deg/span
Both traces can be normalized to measured data with full accuracy
and resolution.
Corrects for directivity, frequency response and source match
errors
Remote programming via the Hewlett-Packard Interface Bus (HPIB). The HP 3677A/B S-Parameter Test Sets are programmable
through the HP 3577A interface only.
401 data points (single parameter) can be transferred directly to an
HP 200 series computer in Basic language as follows:
ASCII mode: Typically 1500 ms
Binary-floating point mode: Typically 160 ms
Graphics Capabilities
GENERAL CHARACTERISTICS
External Reference Frequency Input
Frequency
Level
Impedance
Connector
Reference Frequency Output
Frequency
Level
Impedance
Connector
External Trigger
Connector
Plotter Control
12 lines of text with 40 alphanumeric characters per line, and high
resolution line vectors can be displayed through HP-IB commands
10 MHz/N. N is an integer from 1 to 100.
0 dBm ± 10 dB, nominal
50Ω, nominal
BNC female, rear panel
10 MHz
Typically 0 dBm
50Ω, nominal
BNC female, rear panel
Triggers on negative TTL transition or contact closure to ground
BNC female, rear panel
Directly compatible with HP-IB graphics plotters that use HewlettPackard Graphics Language (HP-GL) with listen only capability:
HP 7470A, HP 7475A, HP 7550A, HP 7090A.
Save/Recall
Operating Conditions
Front-panel setups can be stored in non-volatile memory locations
1 through 5. Last state is saved when power is removed.
Temperature
Relative Humidity
Altitude
Non-Operating Conditions
Temperature
Altitude
Power
Weight
Dimensions
0 °C to +55 °C
<95% at 40 °C
<4,572 m (15,000 ft)
-40 °C to +75 °C
<15,240 m (50,000 ft)
115V + 10%, -25% (47 Hz to 440 Hz), or 230 V + 10%, -15%
31 kg (67 lb) net; 41 kg (90 lb) shipping
222 mm H X 426 mm W X 578 mm D ( 8.75 in. X 16.75 in. X
22.75 in.)
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.