O
p
e r a t i
n
g
i
n
s t r
u
c t i
o
n
s
Boiler
Q 25S
Q 38S
Q 51S
Q 60S
G.C No
41-310-08
41-310-09
41-310-10
41-310-11
Q 25C
Q 38C
Q 51C
47-310-10
47-310-11
47-310-12
CE PIN 0063BQ3021
8G.52.4000/10.05
Changes
reserved
SHR
Introduction ...................................................... 3
Safety ............................................................... 4
Description of the boiler .................................... 5
Explanation of the function keys and display .... 7
The Reset key .................................................. 7
The boiler display ............................................. 8
Water pressure in the central heating system .. 9
Replenishing the central heating .................... 10
Turning the boiler off ....................................... 12
Error, maintenance and warranty ................... 13
Adjustments .................................................... 14
Q
2
Opera
ting
instructions
Important!
It is in your own interest that we should know that you have an
ATAG
boiler. Please fill out the warranty card completely and send it back
to
us. Then we can be fully at your service.
Content
These operating instructions describes the
functioning and the operating of the SHR
boilers. This manual is for the end user.
For
installation and servicing there is a installation
&
servicing instructions manual for the installer.
Read this manual fully before operating the boiler.
In
case of doubt or errors contact your installer.
ATLANTIC BOILERS reserves the right
to
change the specifications and dimensions
without
prior notice. Work on the boiler must
be
carried out by a competent person, (Ref:
Gas
Safety Installation and Use ) using
correctly
calibrated instruments with current
test
certification.
Q
3
Operating
instructions
Introduction
In case
you
smell
gas:
-
-
No naked flames! Do not smoke!
Do not operate electrical switches for lights
or
any other appliance.
Do not use a telephone
Turn off gas supply at meter
Open windows and doors
Notify any persons in the building and leave the
building at once.
Call Gas company or installer only when
outside the building
-
-
-
-
-
Protection
for corrosion
Do not use any sprays, chlorine containing agents,
solvents, paint etc. around the boiler or around
the
air intake supply entrance of the boiler.
These
substances have negative influences on the
boiler
and can lead to corrosion resulting in failure of
the
boiler.
Checking the water pressure
Check the water pressure in the central heating
installation regularly.
Use only potable water for filling.
Additives only after clearance by Atlantic
boilers.
Contact your installer in case of doubt.
Q
Operating
instructions
Safety
The SHR boiler is a room sealed, condensing
and modulating central heating boiler, with
or
without an integrated hot water facility.
The boiler is provided with a compact stainless
steel heat exchanger with smooth tubes. A
well
thought out principal using durable materials.
The boiler burns gas for supplying warmth.
The
heat is transferred in the heat exchanger to
the
water in the central heating system. By
cooling
down the flue gasses condensate is formed.
This
results in high efficiency. The condensate,
which
has no effect on the heat exchanger and
the
function of the boiler, is drained through an
internal
siphon.
The boiler is provided with an intelligent control
system (CMS Control Management System).
The
boiler anticipates the heat demand of the
central
heating system or the hot water facility.
When an outside sensor is connected to the boiler,
the boiler works weather dependantly. This
means
that the boiler control measures the
outside
temperature and flow temperature. With this
data
the boiler calculates the optimal flow
temperature
for the installation.
Q
5
Operating
instructions
Stainless
Super solid kind of
steel
which keeps its quality
for
life. It will not rust or erode
in
contrast to
composition
materials, like aluminium.
Modulating
Higher or lower burning
according to the heat
demand.
Condensing
Retrieves heat from the
flue gasses. Water
condensates on the heat
exchanger.
Room sealed boiler
The boiler retreives
its
combustion air from
outside
then discharges the
flue
gasses to the outside.
Description of the boiler
The efficiency of the boiler is very high and the
radiation convection and standby losses very
low.
The emission of noxious substances is far
below
the fixed standards so the boiler meets
the
requirements of SEDBUK Class A.
Example SEDBUK ClassA
When the boiler is connected to a Brain Q
or Smart a lot of information can be retrieved
from
the boiler. For more information about
the
thermostats. Please refer to the user manuals.
On the left side of the boiler there is a small door.
Through the transparent part you can see
the
boiler status on the display. After opening this
door
you will find the function keys. On the right side
of
the door you will find an instruction card in a
sleeve
with an explanation of the display messages and
BrainQ
Smart
function keys. This
following pages.
is also described in the
Q
6
Operating
instructions
Display
Indication
L.E.D.'s
Step key
Scrolling
Pum
p
programm
on/off
Mode key
Selecting chapters
(Store)
Reset key
Unlocking the boiler
Q
The control panel is provided with a reset key.
When a fault occurs it will be shown by the
flashing
E (Error) with a number code after which the
boiler
is shut down. After pressing the reset key you
can
try to start the boiler again. If the error
message
keeps occurring contact your installer.
7
Opera
ting
instructions
The Reset key
On/of key Pump programm. Continuously yes/no
When 'on' the indication L.E.D. is illuminated.
In most situations the pump can stay in position 'off'.
During severe frost It is possible (when there is no
outside
sensor connected), to choose manually to let the
circulation
pump circulate continually thus reducing the chance of
freezing
pipes (garage, attic or other cold spaces / rooms) which
are
sensitive to frost.
When the pump is
switched
on continuously it can
lead
to undesired heating up
of
the central heating
system
during the summer.
On/off key Domestic hot water (DHW)
When 'on' the indication L.E.D. is illuminated.
On/off key Central heating.
When 'on' the indication L.E.D. is illuminated.
l heating
Domesti
c
Hot water
on/off
Explanation of the function keys and display
The reading of the boiler display can be done in two ways.
The Good reading
During this reading the display will only show
what
is necessary. Under normal circumstances
the
display will give a Good reading. If a fault
is
detected the boiler will be blocked. This will
be
shown with, alternate display of Good, with an
E
of Error or a BL of Blocking and a number code.
For
further information refer to page 13
"Errors,
maintenance and warranty" .
Th
e technica
l reading
During this reading the display will show in
which
operating status the boiler is active. The
technical
reading is shown alternately with the
water
pressure. The first figure in the technical read
out
indicates the status in which the boiler is active
and
the third and fourth figure indicate the
water
temperature of the boiler. For example in
the
reading P 1.9 the character P stands for pressur
e
which represents the water pressure. The third
and
fourth figure indicate the water pressure in bar.
If a fault is found, the same is shown as
described
under "The Good reading".
Q
8
Operating
instructions
Selecting the Technical or
Good
rea
ding.
- Press the Step key for 5 seconds.
The display will change from the Good reading to
the
technical reading or vice versa.
The boiler display
The installation will function optimally with a water
pressure of between 1,5 and 1,7 bar.
If the water pressure drops below 1 bar, the display
will show FILL. During this message the boiler
will
remain functioning at a reduced level.
After
replenishing the system just above 1,5 bar
the
message FILL will disappear and the boiler wi
ll
function normally again.
When the water pressure drops below 0,7 bar, the
display will show a flashing FILL text.
The boiler will shut down and will function normally
again after replenishing the system to just above
1,5 bar.
To retreive the water pressure on the display from
the Good reading:
- Press the Step key once briefly.
The water pressure will be shown.
Press the Step key briefly to return to the
Good
reading.
Q
9
Operating
instructions
Message ' Water
pressure
too low' on you
r
thermostat.
On the display of the
Brain
Q as well as the
Smart a low
water
pressure can be
indicated.
For further information see
the relevant user manual.
Water pressure in the central heating system
The central heating installation needs to be filled with potable (drinking) water.
For topping up the installation you use the filling loop according to the following
procedure:
(If in any doubt please contact your dealer)
1 Switch all functions off (heating, DHW and pump);
3 Slowly open the filling loop (Indication on display increases);
5 STOP appears on the display;
7 De-aerate the complete installation, start at the lowest point;
9 Close the filling loop;
11 If A xx appears on the display, wait for 17 minutes;
13 Close the filling loop;
15 Be sure that the filling loop is closed.
Q
After the automatic de-aeration programm (A xx) is finished the boiler will
return to the Good reading or Technical reading.
10
Operating
instructions
14 Press the ‘STEP’-button;
12 Check the waterpressure and if necessary top it up to 1,5 to 1,7 bar
10 Activate functions required (heating , DHW and/or pump );
8 Check the water pressure and if necessary top it up;
6 Close the filling loop;
4 Fill up slowly to 1.5 to 1.7 bar;
2 Briefly push the 'STEP'-button: P x.x = water pressure in bar;
Replenishing the central heating system
Check the water pressure regularly and top up the installation when
necessary.
The working pressure of the installation should be between 1.5 and 1.7 bar
Q
11
Operating
instructions
It can take a while before all air has dis-appeared from a filled installation. Especially
in the first week noises can be heard which indicate the presence of air.
The
automatic air vent in the boiler will make this air disappear, which means the
water
pressure will reduce during this period and therefore topping up with water will
be
necessary to adjust the flow water temperature
The boiler will not function directly. The automatic de-aeration programm of
about
17 minutes will start after one of the three programm keys is pressed. The
display
will show where A stand s for Automatic de-aeration programm Active
and
the number on the right indicates the actual water temperature of the boiler.
Holiday
period:
Adjust the thermostat to the holiday period.
See
the user thermostat manual. The hot water
facility
can be switched off by means of the program key
on the control panel.
Re-setting the ce
ntral heating system:
Switch off the three program keys
, ,
when these are activated.Switch off the power
supply. When the boiler is being drained
one
should take into account that a part of the
heating
water will remain in the boiler. When risk of
frost
arises one should take care that the
remaining
central heating water in the boiler does not freeze.
Q
12
Operating
instructions
Holiday
The BrainQ
room
thermostat is
provided
with a holiday
programm.
The holiday period can
be
adjusted on the
thermostat
itself. The central
heating
and DHW supply
are
switched off during
that
period. There is also
the
option that only the
central
heating is switched off.
With
all of these possibilities
the
frost protection system
is
active.
urning the boiler off
If a fault is detected the boiler will be blocked. This
will be reflected, by an alternate display of
Good,
with an E of Error or a BL of Blocking and a
number
code.
You can try to reset the boiler by pressing
the
Reset key once. If the problem remains
please
contact your installer and inform them about
the
fault and give them the number code.
If you discover any leaks from the boiler contact
your installer.
We advise you to obtain a service contract
with
your installer for regular maintance
and
adjustment to keep your boiler safe and in
good
condition.
The casing of the boiler consists of metal and
plastic parts which can be cleaned with a
normal
non abrasive cleaning agent.
You can find the warranty conditions in the
warranty card which is supplied with the boiler.
Q
13
Operating
instructions
Error, maintenance and warranty
The boiler has a large number of settings options.
We advise you to contact your installer
for
adjusting the boiler to the required settings.
Adjusting
the flow
water
temperature
(CH)
-
Press the Mode key briefly
(from the Technical reading).
The display will show PARA .
Press the Step key once.
The display will show 1 85 .
Press the + or the - key to alter the adjustments,
if necessary.
Press the Store key to confirm the setting.
The display will flash once.
Press the Mode key briefly.
The display will show StbY for a short while
and
will return to the Technical reading.
The flow water temperature that has been
adjusted
-
-
-
-
only applies to the central heating and is independent of the hot water facility for
the
cylinder.
Q
14
Operating
instructions
Adjustments
Adjusting
the
type
of
installation
The boiler is designed in such a way that it will
adjust itself automatically to what is necessary for
a normal heating system. In some cases
the
installation may have convectors or
complete
underfloor heating.
One can easily choose heating
installation
adjustments appropriate for the system such
as
maximum water-flow temperature or for
the
warming up of the installation after a night
period.
Adjustment goes as follows:
+
-
Store
Mode
Step
Reset
-
Press (from the Technical) reading the Mode
key once;
Press the Step key twice;
The display will show 2 01.
Press the + or the - key to alter the type
of
installation according to the table below;
Press the Store key to confirm the setting;
The display will flash once.
Press the Mode key once;
The display will show StbY for a short while
and
will return to the Technical reading.
-
-
-
-
temperature
01
Radiators; air heat
ing; conv
ectors
85°C
Q
a
dditional
heat
ing
03
Under f
loor
heat
ing with radiators as additional h
eat
ing
60°C
= factory setting
When a type of installation has been chosen with a low water-
flow
temperature
it is possible that in case of a severe winter period the temperature of
the
heating system will need to be increased slightly. In such situations
the
installation choice may need to be changed, so that a higher flow
temperature
can be chosen. This adjustment would normally be carried out by your
installer
during the installation and commissioning.
15
Operating
instructions
04
f
ull under floor
heat
ing
50°C
02
Radiators
with large
surface areas or
under floor h
eat
ing as
70°C
Sel
ect
ion T
ype of
in
stallat
ion
Flow w
ater
Details of your installer:
Name of installer:
Address:
Contact:
Phone number:
Phone number outside business hours:
Atlantic
2000
Box 11
, Ashton
Under Lyne,
Lancashire, OL6 7TR
Tel:
0161 621 5960
or: 020 7237 4912
Fax:
0161 621 5966
E-mail:
info@atlantic2000.co.uk Web: www.atlanticboilers.com
Loading...