ASUS L84ID1 User Manual
NOTEBOOK PC
USER’S MANUAL
Product Name: Notebook PC
Manual Revision: 1.01 E548
Release Date: April 2000
SAFETY STATEMENTS
Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of a shielded-type power cord is required in order to meet FCC
emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded
cables to connect I/O devices to this equipment. You are cautioned that changes or
modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Reprinted from the Code of Federal Regulations #47, part 15.193, 1993. Washington DC: Office of the
Federal Register, National Archives and Records Administration, U.S. Government Printing Office.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
set out in the Radio Interference Regulations of the Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
For use with AC Adaptor Model ADP-45GB (Pour Utiliser Avec Modele ADP-45GB)
2
Nordic Cautions (for Notebook PC with Lithium-Ion Battery)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions. (English)
VORSICHT! Explosionsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben
oder einem vom Hersteller empfohlenem ähnlichen T yp. Entsorgung gebrauchter Batterien nach Angaben
des Herstellers. (German)
ADVARSELI! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med
batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. (Danish)
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ
som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. (Swedish)
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu. V aihda paristo ainoastaan laitevalmistajan
sousittelemaan tyyppiin. Hävitä käytetty paristo valmistagan ohjeiden mukaisesti. (Finnish)
ATTENTION! Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer
uniquement avec une batterie du mêre type ou d’un type équivalent recommandé par le constructeur.
Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (French)
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en
tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens
instruksjoner. (Norwegian)
(Japanese)
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain
U.S.A. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
3
CTR 21 Approval (for Notebook PC with built-in Modem)
Danish
Dutch
English
Finnish
French
German
Greek
4
Italian
Portuguese
Spanish
Swedish
5
Contents
SAFETY STATEMENTS 2
Federal Communications Commission Statement..............................................2
Canadian Department of Communications Statement ....................................... 2
Nordic Cautions (for Notebook PC with Lithium-Ion Battery)..............................3
Macrovision Corporation Product Notice ............................................................3
CTR 21 Approval (for Notebook PC with built-in Modem) ..................................4
SECTION 1
INTRODUCING THE NOTEBOOK PC 9
About This User’s Manual...................................................................................... 10
Notes For This Manual...................................................................................... 10
Caring Information ................................................................................................. 11
Transportation Precautions.................................................................................... 12
SECTION 2
KNOWING THE PARTS 13
Top Side................................................................................................................. 14
Front Side .............................................................................................................. 16
Left Side................................................................................................................. 17
Right Side .............................................................................................................. 18
Rear Side............................................................................................................... 20
SECTION 3
GETTING STARTED 23
Inserting and Removing the Battery Pack ............................................................. 24
Using the Battery Pack .......................................................................................... 25
Before using your Notebook PC on the road .................................................... 25
Battery Care......................................................................................................25
Operating Systems ................................................................................................ 25
Support Software .............................................................................................. 25
Power Connection ................................................................................................. 26
Powering ON Your Notebook PC........................................................................... 27
The Power-On Self Test (POST) ...................................................................... 27
Save-to-Disk Partition ............................................................................................ 28
Restarting or Rebooting......................................................................................... 28
LED Status Indicators ............................................................................................ 29
Using the Keyboard ............................................................................................... 30
Colored Hot Keys..............................................................................................30
Microsoft Windows™ Keys ............................................................................... 31
Keyboard as a Numeric Keypad ....................................................................... 31
Keyboard as Cursors ........................................................................................ 32
6
SECTION 4
USING THE NOTEBOOK PC 33
Floppy Disk Drive...................................................................................................34
CD/DVD-ROM Drive .............................................................................................. 35
Laser Safety......................................................................................................35
CDRH Regulations ........................................................................................... 35
DVD-ROM Drive (optional) .................................................................................... 36
Overview........................................................................................................... 36
Regional Playback Information ......................................................................... 37
Region Definitions.............................................................................................37
Using the CD-ROM Drive ................................................................................. 38
Listening to Audio CD ....................................................................................... 39
Pointing Device...................................................................................................... 40
Using the Touchpad .......................................................................................... 40
Caring for the Touchpad ................................................................................... 42
PS/2 Connection (optional).................................................................................... 42
External Display Connections (optional)................................................................ 43
PC Cards (PCMCIA).............................................................................................. 44
32-bit CardBus & Zoomed Video Port .............................................................. 44
Inserting a PC Card (PCMCIA)......................................................................... 45
Removing a PC Card (PCMCIA) ...................................................................... 45
External Audio Connections (optional)................................................................... 46
Printer Connection (optional) ................................................................................. 46
IR Wireless Communication .................................................................................. 47
Guidelines for using IR communication ............................................................ 47
Enabling Infrared .............................................................................................. 47
Universal Serial Bus .............................................................................................. 48
Driver Support...................................................................................................48
AC Power System..................................................................................................48
Battery Power System ........................................................................................... 49
Charging the Battery Pack................................................................................ 49
Using Battery Power ......................................................................................... 50
Power Management Modes................................................................................... 51
Full Power Mode & Maximum Performance ..................................................... 51
APM and ACPI..................................................................................................51
Suspend Mode..................................................................................................51
Standby Mode...................................................................................................52
Power State Summary...................................................................................... 52
Thermal Power Control..................................................................................... 53
System Memory Expansion ................................................................................... 53
Processor Upgrades .............................................................................................. 53
Modem and Network Connections (optional).........................................................54
Modem Connection...........................................................................................54
Network Connection ......................................................................................... 54
Securing Your Notebook PC .................................................................................. 55
Other Security Products....................................................................................55
7
SECTION 5
CONFIGURING THE BIOS 57
Updating Your BIOS...............................................................................................58
Creating a BIOS Update Floppy Disk ............................................................... 58
Updating BIOS Procedures .............................................................................. 59
BIOS Setup Program ............................................................................................. 60
BIOS Menu Bar.................................................................................................61
BIOS Legend Bar..............................................................................................61
Main Menu ............................................................................................................. 63
IDE Primary Master ............................................................................................... 64
IDE Primary Slave ................................................................................................. 67
Advanced Menu..................................................................................................... 68
I/O Device Configuration........................................................................................ 70
Security Menu........................................................................................................ 72
System Boot Entry ............................................................................................ 73
Hard Disk Unlock: ............................................................................................. 73
Password Usage Summary ................................................................................... 73
The Power Menu ................................................................................................... 74
Boot Menu ............................................................................................................. 76
Exit Menu............................................................................................................... 77
APPENDIX 78
PortBar Accessory ................................................................................................. 80
Features............................................................................................................80
Usage ...............................................................................................................80
Docking Solution............................................................................................... 81
Vehicle/Air Power Adapter Accessory.................................................................... 82
Features............................................................................................................82
Usage ...............................................................................................................82
Internal Modem Compliancy .................................................................................. 83
Protocols and Compliancy ................................................................................ 83
Glossary................................................................................................................. 85
INDEX.................................................................................................................... 88
Owner Information ................................................................................................. 90
8
SECTION 1
INTRODUCING THE NOTEBOOK PC
About This User’s Manual
Caring Information
Transportation Precautions
9
About This User’s Manual
You are reading the Notebook PC User’s Manual. This User’s Manual provides information on the
various components in the Notebook PC and how to use them. The following are major sections of this
User’s Manuals:
1. Introducing the Notebook PC
Introduces you to the Notebook PC and this User’s Manual.
2. Knowing the Parts
Gives you information on the Notebook PC’s components.
3. Getting Started
Gives you information on getting started with the Notebook PC.
4. Using the Notebook PC
Gives you information on using the Notebook PC’s components.
5. Configuring the BIOS
Gives you information on configuring the BIOS software.
6. Appendix
Introduces you to optional accessories and gives additional information.
Notes For This Manual
This User’s Manual was created using Macintosh versions of Adobe® PageMaker™ 6.52, Adobe
Photoshop™ 5.0.2, and Macromedia® Freehand™ 8.0.1. The body text type used in this manual is
“Times” (MAC) or “Times New Roman” (Windows™) and headings are “Helvetica” (MAC) or “Arial”
(Windows™). A few notes and warnings in bold are used throughout this guide that you should be
aware of in order to complete certain tasks safely and completely . These notes have different degrees of
importance as described below:
®
WARNING! Information to prevent
damage to components, damage to
data, or personal injury.
IMPORT ANT : Information that must be
followed in order to complete a task.
Text enclosed in < > represents a key
on the keyboard; do not actually type
the < > and enclosed letters.
TIP: Tips and useful information for
power (advanced) computer users.
NOTE: Tips and information to aid in
completing a task.
10 1. Introducing the Notebook PC
Caring Information
WARNING! The following safety precautions will increase the life of the Notebook PC.
Follow all precautions and instructions. Except as described in this manual, refer all
servicing to qualified personnel. Do not use damaged power cords, accessories, or
other peripherals. Do not use strong solvents such as thinners, benzene or other
chemicals on or near the surface.
Disconnect the AC power and remove the battery pack(s) before cleaning. Wipe the Notebook PC using
a clean cellulose sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few
drops of warm water and remove any extra moisture with a dry cloth.
DO NOT place on uneven or unstable work
surfaces. Seek servicing if the casing has
been damaged.
DO NOT expose to
strong magnetic or
electrical fields.
NOTE: The surface glaze is easily dulled if not properly cared for. Be careful not to rub
or scrap the Notebook PC surfaces.
DO NOT place or drop
objects on top and do
not shove any foreign
objects into the Notebook PC.
DO NOT expose to extreme temperatures (below
0˚C (32˚F) or above 50˚C(122˚F)) or to direct sunlight. Do not block the fan vents!
DO NOT expose to liquids, rain, or moisture.
Seek servicing if liquid
has been spilled into the
Notebook PC.
DO NOT expose to
dirty or dusty environments.
DO NOT press or touch
the display panel. Do not
place together with small
items that may scratch or
enter the Notebook PC.
111. Introducing the Notebook PC
Transportation Precautions
T o prepare the Notebook PC for transport, you should turn it OFF and disconnect all external peripherals to prevent damage to the connectors. The hard disk drive’s head retracts when the power is turned
OFF to prevent scratching of the hard disk surface during transport. Therefore, you should not transport
the Notebook PC while the power is still ON. Close the display panel and check that it is latched
securely in the closed position to protect the keyboard and display panel.
Remove Floppy Disks
Make sure that the 1.44MB floppy disk drive does not contain a diskette when transporting the Notebook PC. When a diskette is inserted into the floppy disk drive, the eject button protrudes out. If you
attempt to transport the Notebook PC with a diskette in the drive, you risk damaging the eject button
and also risk scratching the surface of the diskette when the floppy disk drive is jolted.
Cover Your Notebook PC
Use a carrying case such as the one supplied with your Notebook PC to protect it from dirt, water,
shock, and scratches.
Charge Your Batteries
If you intend to use battery power, be sure to fully charge your battery pack and any optional battery
packs before going on long trips. Remember that the power adapter charges the battery pack as long as
it is plugged into the computer and an AC power source. Be aware that it takes much longer to charge
the battery pack when the Notebook PC is in use.
Travelling Precautions
Contact your airline if you want to use the Notebook PC on the airplane. Most airlines will have restrictions for using electronic devices. Most airlines will allow electronic use only between and not during
take-offs and landings.
IMPORTANT: There are three main types of airport security devices: X-ray machines
(used on items placed on conveyor belts), magnetic detectors (used on people walking through security checks), and magnetic wands (hand-held devices used on people
or individual items). Y ou can send your Notebook PC and diskettes through airport Xray machines. However, it is recommended that you do not send your Notebook PC or
diskettes through airport magnetic detectors or expose them to magnetic wands.
12 1. Introducing the Notebook PC
SECTION 2
KNOWING THE PARTS
Top Side
Front Side
Left Side
Right Side
Rear Side
13
Top Side
Refer to the diagram below to identify the components on the top side of the Notebook PC.
Display Panel
Microphone
Cooling Fan
and air entry
~
‘
@
!
Tab
#
$
%
S2
S1
&
^
*
)
(
Sys Rq
_
{
[]
Prt Sc
+
Back
Space
}
\
"
Status LEDs
Very Light All-in-One: Including the battery pack weighs only 6.28lbs (2.85Kg).
Keyboard
Touchpad
Touchpad
Buttons
14 2. Knowing the Parts
The following describes the components of the Notebook PC as viewed from the top as shown by the
illustration on the previous page.
Display Panel
The display panel functions the same as a desktop monitor. The Notebook PC uses a 1024x768 14.1”
active matrix TFT LCD, which provides excellent viewing like that of desktop monitors. Unlike desktop monitors, the LCD panel does not produce any radiation or flickering, so it is easier on the eyes.
NOTE: While the Notebook PC is ON, closing the display panel will turn OFF the display to conserve power and opening the display panel will turn the display back ON.
Opening the Display Panel
One spring-loaded latch on the front of the Notebook PC locks the display panel in the closed position
when the Notebook PC is not in use. T o open the display panel, slide the latch to the left with your thumb
and raise the display panel with the same thumb. This design allows a single hand to unlock and open the
display panel. Slowly tilt the display panel forward or backward to a comfortable viewing angle.
WARNING! When opening, do not force the display panel down to the table or else
the hinges may break! Never lift the Notebook PC by the display panel!
Display Panel Care
The LCD screen is very delicate and requires careful handling. Pay attention to the following precautions:
• When not in use, keep the display panel closed to prevent dust accumulation.
• Do not use chemical cleaners on the screen. Wipe only with a dry cloth or tissue.
• Do not put your fingers or any objects directly on the screen.
• Do not press or lay any objects on the machine when it is closed.
• Do not carry the Notebook PC with small or sharp objects (e.g. paper clips or staples) that may enter
the Notebook PC and scratch the display panel.
Microphone
The built-in microphone provides a source for inputting mono audio for general note taking, voicemail
recording, or for use with Internet phone software. See “Rear Side” for external microphone connection.
Cooling Fan
The cooling fan turns ON when the temperature rises past a set threshold. The cooling fan is an extra
feature needed for upgrading to faster processors in the future. The top screen allows cool air to enter
the Notebook PC. Do not block the area above the keyboard!
Keyboard
The keyboard provides full-sized 19mm keys with 3mm travel and palm rest. T wo W indows™ function
keys are provided to help ease navigation in the Windows™ operating system.
Touchpad and Buttons
The touchpad with its two buttons is a pointing device that provides the same functions as a desktop
mouse. A scrolling function for Web browsing or Microsoft
third-party software on the support CD.
®
Office navigation is available using the
Status LEDs
The Notebook PC has status LEDs to display capital lock, number lock, storage device access, battery
charging, and power statuses. Details are described later in this manual.
152. Knowing the Parts
Front Side
Refer to the diagram below to identify the components on the front side of the Notebook PC.
Display Panel Latch Power Indicator
35mm
Stereo Speaker Stereo Speaker
The following describes the front components of the Notebook PC as shown by the picture above.
Charge Indicator
310mm
Power Switch
Stereo Speakers
The two built-in speakers allow you to hear stereo audio without additional attachments. The multimedia sound system features an integrated digital audio controller that produces rich, vibrant sound in
high quality 16-bit stereo. With a pair of integrated stereo speakers, a built-in microphone, and both
input and output audio jacks for external audio devices, the Notebook PC fulfills most multimedia
computing needs. All audio features are software controlled.
Display Panel Latch
The display latch is used to lock the display panel in the closed position. Slide the latch to the left to
release the display panel.
Charge Indicator
Indicates that the battery is being charged when ON and fully charged when OFF. This LED only lights
when the power adapter is used. This LED will not light if there is no battery installed. Slow flash
means the battery power is low and require charging. Quick flashing means that the battery pack cannot
be charged and needs replacing.
Power Indicator
The green LED will light to indicate that the Notebook PC is turned ON and blink when the Notebook
PC is in Suspend-T o-RAM mode. This LED will be OFF when the Notebook PC is in Suspend-To-Disk
mode.
Power Switch
The power switch allows powering ON and OFF the Notebook PC. The switch normally rests on the
left and is activated when moved to the right and released.T o prevent accidental turning OFF the power ,
it is designed to take longer to turn OFF than to turn ON the power. The momentary sliding switch
requires about one second to turn ON the power and about two seconds to turn OFF the power.
16 2. Knowing the Parts
Left Side
Refer to the diagram below to identify the components on the left side of the Notebook PC.
PC Card
(PCMCIA) Eject
Kensington
Lock Port
®
Air Vent
DC Power
Input Jack
Fast Infrared Port
PC Card (PCMCIA) Sockets
256mm
The following describes the components on the left side of the Notebook PC as shown by the illustration above.
Kensington® Lock Port
L
The Kensington® lock port allows the Notebook PC to be secured using Kensington® compatible Notebook PC security products. These security products usually include a metal cable and lock that prevents
the Notebook PC to be removed from a fixed object. Some security products may also include a motion
detector to sound an alarm when moved.
Air Vent
The left side fan vent allows warm air to exit the Notebook PC in order to cool the Notebook PC’s
internal components. Do not block any air vents!
DC IN
DC Power Input Jack
The supplied power adapter converts AC power to DC power for use with this jack. Power supplied
through this jack will supply power to the Notebook PC as well as charge the internal battery pack.
Fast Infrared Port
The fast infrared (IrDA) communication port allows convenient wireless data communication with
infrared-equipped devices or computers up to 4Mbits/sec. This allows easy wireless synchronization
with PDAs or mobile phones and even wireless printing to printers. If your office supports IrDA networking, you can wirelessly connect to the network anywhere where there is a direct line of sight to an
IrDA node. Small offices can use IrDA technology to share a printer between several closely placed
Notebook PCs and even send files to each other without a network.
PC Card (PCMCIA) Sockets and Eject
T wo PCMCIA 2.1 compliant sockets for two Type I or T ype II or one Type III PC card are available. The
lower socket includes support for 32-bit CardBus and Zoomed Video. This allows accommodation of all
Notebook PC expansion options such as memory cards, fax/modems, SCSI adapters, high-speed network
adapters, and video capture/conference cards. The two eject buttons allow easy ejection of the PC cards.
172. Knowing the Parts
Right Side
Refer to the diagram below to identify the components on the right side of the Notebook PC.
CD/DVD
Activity LED
Floppy EjectFloppy Disk Drive
256mm
The following describes the components on the right side of the Notebook PC as shown by the illustration above.
CD/DVD
Emergency Eject
CD/DVD Eject
Volume Control
Floppy Disk Drive and Floppy Eject
This is a standard 1.44MB floppy disk drive with Japanese 3-mode floppy support. Floppy disk activity
should be seen through the activity LED next to the power button. Unlike desktop PC floppy disk
drives, the eject button of the Notebook PC is on top of the opening to allow easy floppy ejection from
the top.
WARNING! The floppy disk drive’s eject button protrudes out of the Notebook PC
when a floppy disk is fully inserted and can be easily damaged if struck. Eject the
floppy disk before transporting the Notebook PC.
CD/DVD-ROM Drive
The Notebook PC comes in a 24X CD-ROM model or a 6X DVD-ROM model (the DVD-ROM is also
capable of reading CDs at 24X).
CD/DVD-ROM Activity LED
The activity LED blinks proportionally to the CD/DVD-ROM drive activity and also blinks when
electronically ejecting a CD/DVD.
CD/DVD-ROM Eject and Emergency Eject
The CD/DVD-ROM eject is an electronic eject button for opening the tray. You can also eject the CD/
DVD through the software CD/DVD player or by right clicking the CD/DVD drive in W indows™ “My
Computer.” The emer gency eject is used to eject a CD/DVD in case the electronic eject does not work.
Do not use this in place of the electronic eject.
18 2. Knowing the Parts
Volume Control
The volume control wheel allows fast adjustment of the master audio output volume. For maximum
volume, the digital volume controlled through W indows™ “Volume Control” on the taskbar must also
be maximized.
Hard Disk Drive
The hard disk drive is fixed internally. There is no removable hard disk drive bay.
192. Knowing the Parts
Rear Side
Refer to the diagram below to identify the components on the rear side of the Notebook PC.
External
Monitor Port
Mic In
Serial Port
Parallel Port
Modem/LAN Port
310mm
Audio In
35mm
Headphone TV Out
The following describes the components on the rear side of the Notebook PC as shown by the illustration above.
Port
PS/2 PortDocking Port
2 USB
Ports
Headphone (Jack)
The stereo headphone jack is used to connect the Notebook PC’s audio out signal to amplified speakers
or headphones. Using this jack automatically disables the built-in speakers.
Audio In (Jack)
The audio in provides stereo input from audio sources.
Mic In (Microphone Jack)
The mono microphone jack can be used to connect an external microphone or output signals from audio
devices. Using this jack automatically disables the built-in microphone.
Serial Port
The 9-pin D-sub serial port supports serial devices such as a drawing tablet, mouse, or modem.
Parallel Port
The 25-pin D-sub parallel/printer port supports parallel devices such as a printer or a removable drive.
Docking Port
The docking port is an expansion bus for connection to an optional proprietary PortBar.
Modem/LAN Port (modem or LAN models only)
The dual purpose port (available on internal modem or LAN models) supports an RJ11 telephone cable
or an RJ45 Ethernet cable. The modem supports up to 56K V.90 transfers, and the LAN supports 10BaseT or 100Base-TX standard or duplex networks.
20 2. Knowing the Parts
NOTE: The built-in modem and fast-Ethernet is also available by a dealer (not by user)
upgrade if you did not choose them at the time of purchase. A modem and/or LAN can
be user-installed as a PCMCIA card.
WARNING! The built-in modem does not support the voltage used in digital phone
systems. Do not connect the modem port to a digital phone system or else damage
will occur to the Notebook PC.
External Monitor Port
The 15-pin D-sub monitor port supports a standard VGA-compatible device such as a monitor or projector to allow viewing on a larger external display . An external monitor can also be used for dual-view
or dual-application support to allow referencing data on one display while working on the other display. This feature can really increase your productivity!
TV-Out Port
TV
For times when you need a really big display , try the TV-Out function. TV -Out allows a high definition
connection to a television or video device using a Super VHS (S-Video) cable (not provided). An
adapter is provided for use with RCA inputs available on all standard video devices. This port support
NTSC or PAL formats.
PS/2 Port
The PS/2 port is for connecting an external PS/2 mouse or PS/2 keyboard to the Notebook PC if you do
not want to use the built-in pointing device and keyboard. Simultaneous use requires the optional PS/2
Y-adapter.
USB Port
Universal Serial Bus (USB) supports many USB compatible devices such as keyboards, pointing devices, video cameras, modems, hard disk drives, printers, monitors, and scanners connected in a series
up to 12Mbits/sec. In order to connect more USB devices, you can purchase a third party USB hub.
USB supports hot-swapping of devices so that peripherals can be connected or disconnected while the
Notebook PC is ON.
212. Knowing the Parts
22 2. Knowing the Parts
SECTION 3
GETTING STARTED
Inserting/Removing Battery Pack
Using the Battery Pack
Operating Systems
Power Connection
Powering ON Your Notebook PC
Save-to-Disk Partition
Restarting or Rebooting
LED Status Indicators
Using the Keyboard
23
Inserting and Removing the Battery Pack
Your Notebook PC may or may not have its battery pack inserted. If your Notebook PC does not have
its battery pack inserted, there will be a large opening on the bottom of the Notebook PC. Use the
following procedures to install or remove the battery pack.
To insert the battery pack:
1. Insert the battery pack with the connector side
over the connectors in the battery compartment
as indicated by arrow [1].
1
2. Slide the longer (battery) latch as indicated by arrow [2].
2
To remove the battery pack:
1. Slide the shorter (safety) latch as indicated by
arrow [1].
1
2. Slide the longer (battery) latch a s indicated by
arrow [2].
2
3. The shorter (safety) latch will automatically snap
behind the longer latch as indicated by arrow [3].
3
WARNING! Never attempt to remove the battery pack while the battery power LED is
ON, as this may result in the loss of working data.
3. While holding the longer (battery) latch , lift up
on the battery pack at the indention as indicated
by arrow [3].
Battery
Power LED
24 3. Getting Started
3
2
Using the Battery Pack
Before using your Notebook PC on the road
Before you use your Notebook PC on the road, you will have to charge the battery pack. The battery
pack begins to charge as soon as the Notebook PC is connected to external power. Fully charge the
battery pack before using it for the first time. A new battery pack must completely charge before the
Notebook PC is disconnected from external power. The battery pack is fully charged when the battery
charge light turns OFF. It takes about 3 hours to fully charge the battery when the Notebook PC is
turned OFF and about 5 hours when the Notebook PC is turned ON.
Battery Care
The Li-Ion battery pack has no “Memory Effect” (officially called “Voltage Depressor”) but like all
rechargeable batteries, the number of charges is limited. Fully draining and charging the battery once a
day every day will last over a year but how long beyond that will depend on your environment temperature and humidity. Make sure that the battery is used in a temperature range between 10˚C and 29˚C
(50˚F and 85˚F), taking into account that the Notebook PC’s internal temperature is higher than the
outside. Any temperatures above or below this range will shorten the life of the battery. But in any case,
the battery’s usage time will eventually be too short to use and a new one must be purchased.
Operating Systems
This Notebook PC offers its customers the choice of a pre-installed operating system such as Microsoft
Windows 95, Windows 98, or Windows NT 4.0. The choices and languages will depend on territory.
Support Software
This Notebook PC will come with a support CD that provides BIOS, drivers and applications to enable
hardware features, extend functionality , help manage your Notebook PC, or add functionality not provided by the native operating system. If updates or replacement of the support CD is necessary , contact
your dealer for web sites to download individual software drivers and utilities.
The support CD contains all drivers, utilities and software for all popular operating systems including
those that have been pre-installed. The support CD does not include the operating system itself. The
support CD is necessary even if your Notebook PC came pre-configured in order to provide additional
software not included as part of the factory pre-install.
A recovery CD is optional and includes an image of all the drivers and utilities included on the factory
installed hard drive as well as the operating system itself. The recovery CD provides a comprehensive
recovery solution that quickly restores the Notebook PC’s operating system and software to its original
working state provided that your hard disk drive is in good working order. Contact your retailer if you
require such a solution.
253. Getting Started
Power Connection
Your Notebook PC comes with a universal AC-DC adapter. That means that you may connect the
power cord to any 110V-120V as well as 220V-240V outlets without setting switches or using power
converters. Different countries may require that an adapter be used to connect the provided US-standard AC power cord to a different standard. Most hotels will provide universal outlets to support differ ent power cords as well as voltages. It is always best to ask an experienced traveler about AC outlet
voltages when bringing power adapters to another country.
TIP: You can buy travel kits for the Notebook PC that includes power and modem
adapters for almost every country.
With the AC power cord connected to the AC-DC converter , connect the AC power cord to an AC outlet
(preferably with surge-protection) and then connect the DC plug to the Notebook PC. Connecting the
AC-DC adapter to the AC outlet first will allow you to test the AC outlet’s power and the AC-DC
converter itself for compatibility problems before connecting the DC power to the Notebook PC. The
green power LED on the adapter will light if the power is within accepted ranges.
WARNING! Damage may occur if you use a different adapter to power the Notebook
PC or use the Notebook PC’s adapter to power other electrical devices. If there is
smoke, burning scent, or extreme heat coming from the AC-DC adapter, seek servicing. Seek servicing if you suspect a faulty AC-DC adapter . You may damage both your
battery pack(s) and the Notebook PC with a faulty AC-DC adapter.
NOTE: This Notebook PC may come with either a two or three-prong plug depending
on territory. If a three-prong plug is provided, you must use a grounded AC outlet or
use a properly grounded adapter to ensure safe operation of the Notebook PC.
AC Power Cord
(plug into an
electrical outlet)
(connect other end
of power cord to the
AC-DC converter)
AC-DC
Converter
DC Power Plug
26 3. Getting Started
Powering ON Your Notebook PC
The Notebook PC’s power-ON message will appear on the screen followed by a short beep when you
turn it ON. If necessary, you may adjust the brightness by using the hot keys. If you need to run the
BIOS Setup to set or modify the system configuration, press [F2] upon bootup to enter the BIOS Setup.
WARNING! Never turn OFF or reset your Notebook PC while the hard disk or floppy
disk is in use and the activity LED is lit; doing so can result in loss or destruction of
your data. To protect the hard disk drive, always wait at least 5 seconds after turning
OFF your Notebook PC before turning it back ON.
NOTE: Before bootup, the display panel will flash when the power is turned ON. This
is part of the Notebook PC’s test routine and is not a problem with the display.
The Power-On Self Test (POST)
When you turn ON the Notebook PC, it will first run through a series of software-controlled diagnostic
tests called the Power-On Self Test (POST). The software that controls the POST is installed as a
permanent part of the Notebook PC’s architecture. The POST includes a record of the Notebook PC’s
hardware configuration, which is used to make a diagnostic check of the system. This record is created
by using the BIOS Setup program. If the POST discovers a difference between the record and the
existing hardware, it will display a message on the screen prompting you to correct the conflict by
running BIOS Setup. In most cases the record should be correct when you receive the Notebook PC.
When the test is finished, you may get a message reporting “No operating system found” if the hard
disk was not pre-loaded with an operating system. This indicates that the hard disk is correctly detected
and ready for the installation of a new operating system.
The S.M.A.R.T. (Self Monitoring and Reporting Technology) will check the hard disk drive during
POST and will give a warning message if the hard disk drive requires servicing. If any critical hard disk
drive warning is given during bootup, backup your data immediately and run Windows disk checking
program. To run Window’s disk checking program: (1) right-click any hard disk drive icon in “My
Computer”, (2) choose Properties, (3) click the Tools tab, (4) click Check Now, (5) select a hard disk
drive, (6) select Thorough to also check for physical damages, and (7) click Start. Third party disk
utilities such as Symantec’s Norton Disk Doctor can also perform the same functions but with greater
ease and more features.
WARNING! If warnings are still given during bootup after running a software disk
checking utility, you should take your Notebook PC in for servicing. Continued use
may result in data loss.
273. Getting Started
Save-to-Disk Partition
The Notebook PC supports Advanced Power Management to save battery power and extend its working time. One type of power management is “Save-to-Disk.” Save-to-Disk is a suspend mode where
your operating system and application data is saved to a separate partition and retrieved when the
Notebook PC comes out of suspend mode. A partition is a space on the hard disk drive equivalent to
having a second hard disk drive. If you would like the Notebook PC to support the Save-to-Disk mode,
run the PHDISK.EXE utility to setup a Save-to-Disk partition on your hard disk. The Save-to-Disk
partition must be larger than the total system memory of the Notebook PC. T o check whether a Save-toDisk partition exist on your hard drive, run FDISK.EXE located in Windows’ command directory or
Windows rescue floppy disk. You can also compare your working partition’s size with the hard drive’s
size as shown in BIOS setup. See the Drivers and Utilities Support CD User’s Manual for detailed
usage instructions.
WARNING! All other partitions and their data will be cleared by the PHDISK.EXE utility . This must be done BEFORE you install an operating system onto your hard disk.
The included hard disk drive comes with the Save-to-Disk partition pre-configured
from the factory.
Restarting or Rebooting
After installing drivers (please see the “Drivers and Utilities
Guide”), installing applications, or making configuration changes,
you may be prompted to restart the system to update the operating
system and complete the installation process. To restart the system, press the <Ctrl><Alt><Del> keys simultaneously. This is
known as a “warm boot.” If this “warm boot” does not restart the
Notebook PC, you can reset the Notebook PC by using a “cold
boot” which is switching the Notebook PC’s power OFF and then
back ON. Remember to wait 5 seconds before switching the Notebook PC back ON.
NOTE: If neither of these methods work, you can press the reset button located in a
small hole on the bottom-left side of the Notebook PC .
Powering OFF the Notebook PC
For operating systems equipped with APM or ACPI (Windows 98/2000), the Notebook PC can be
powered OFF by using Start | Shut Down... | Shut down. For operating systems without proper power
management (DOS, Windows NT), you must power OFF the Notebook PC by holding the power switch
for 2 seconds (as opposed to 1 second to power ON) after closing applications and exiting operating
systems. This is necessary in order to prevent accidental power-OFFs. It will take 4 seconds to power
OFF the Notebook PC if you do it while the Notebook PC hangs and stopped responding,
28 3. Getting Started
LED Status Indicators
There are several LED status indicators on the Notebook PC. The LED status indicators give information on the Notebook PC’s current operating and keyboard statuses. The following illustration shows
the meaning of each status LED.
Capital
Lock
A
Number
Lock
1
Activity
Indicator
Charge
Indicator
Power
Indicator
The following gives a description for each of the LED status indicators.
Capital Lock
A
Indicates that capital lock [Caps Lock] is activated when lighted. Capital lock allows some of the
keyboard letters to type using capitalized letters (e.g. A, B, C). When the capital lock light is OFF, the
typed letters will be in the lower case form (e.g. a,b,c).
Number Lock
1
Indicates that number lock [Num Lk] is activated when lit. Number lock allows some of the keyboard
letters to act as numbers for easier numeric data input.
Activity Indicator
Indicates that the Notebook PC is accessing the floppy, hard disk, CD/DVD-ROM drive. The light
flashes proportional to the access time.
Charge Indicator
Indicates that the battery is being charged when ON and fully charged when OFF. This LED only lights
when the power adapter is used. This LED will not light if there is no battery installed. Slow flash
means the battery power is low and require charging. Quick flashing means that the battery pack cannot
be charged and needs replacing.
Power Indicator
The green LED will light when the power is ON and blink when in suspend-to-RAM mode. This LED
will be OFF when in suspend-to-disk mode.
293. Getting Started
Loading...