ASUS J1800I-A, E8587 User Manual

J1800I-A

Motherboard

E8587 First Edition

January 2014

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional data, you may obtain it for a period of three years after our last shipment of the product, either

(1) for free by downloading it from http://support.asus.com/download or (2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location

where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc. Legal Compliance Dept. 15 Li Te Rd., Beitou, Taipei 112 Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary/object code.

This offer is valid to anyone in receipt of this information. ASUSTeK is eager to duly provide complete source code as required under various Free Open Source

Software licenses. If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notication to the email address gpl@asus.com, stating the product and describing the problem (please DO NOT send large attachments such as source code archives, etc. to this email address).

Contents

Safety information ...................................................................................................... iv

About this guide ......................................................................................................... iv

Package contents ....................................................................................................... vi

J1800I-A specications summary ............................................................................. vi

Product introduction

1.1 Before you proceed ...................................................................................... 1-1

1.2 Motherboard overview .................................................................................

1.3 Central Processing Unit (CPU) ....................................................................

1.4 System memory ............................................................................................

1.5 Expansion slots ............................................................................................

1.6 Jumpers

1.7 Connectors ..................................................................................................

1.8 Software support ........................................................................................

BIOS information

2.1 Managing and updating your BIOS .............................................................2-1

2.2 BIOS setup program .....................................................................................

2.3 My Favorites

2.4 Main menu ...................................................................................................

2.5 Advanced menu ..........................................................................................

2.6 Monitor menu ..............................................................................................

2.7 Boot menu ...................................................................................................

2.8 Tools menu ..................................................................................................

2.9 Exit menu ....................................................................................................

.........................................................................................................1-9

.................................................................................................. 2-9

1-2

1-4

1-8

1-11

1-18

2-6

2-10

2-12

2-21

2-24

2-29

2-30

Appendices

Notices ..................................................................................................................... A-1

ASUS contact information ...................................................................................... A-4

iii

Safety information

Electrical safety

To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

• before relocating the system.

When adding or removing devices to or from the system, ensure that the power cables

• for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

Before connecting or removing signal cables from the motherboard, ensure that all

• power cables are unplugged.

Seek professional assistance before using an adapter or extension cord. These devices

• could interrupt the grounding circuit.

Ensure that your power supply is set to the correct voltage in your area. If you are not

• sure about the voltage of the electrical outlet you are using, contact your local power company.

If the power supply is broken, do not try to x it by yourself. Contact a qualied service

• technician or your retailer.

Operation safety

Before installing the motherboard and adding devices on it, carefully read all the manuals

• that came with the package.

Before using the product, ensure all cables are correctly connected and the power

• cables are not damaged. If you detect any damage, contact your dealer immediately.

To avoid short circuits, keep paper clips, screws, and staples away from connectors,

• slots, sockets and circuitry.

Avoid dust, humidity, and temperature extremes. Do not place the product in any area

• where it may become wet.

Place the product on a stable surface.

•

If you encounter technical problems with the product, contact a qualied service

• technician or your retailer.

About this guide

This user guide contains the information you need when installing and conguring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it supports.

• Chapter 2: BIOS information

This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.

Where to nd more information

Refer to the following sources for additional information and for product and software updates.

1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.

2. Optional documentation

Your product package may include optional documentation, such as warranty yers,

that may have been added by your dealer. These documents are not part of the standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a task

IMPORTANT: Instructions that you MUST follow to complete a task. .

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text Indicates a menu or an item to select.

Italics

<Key> Keys enclosed in the less-than and greater-than sign

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key

Used to emphasize a word or a phrase.

means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or Return key.

names are linked with a plus sign (+).

Package contents

Check your motherboard package for the following items.

Motherboard ASUS J1800I-A motherboard

Cables 2 x Serial ATA 3.0 Gb/s cables

Accessories 1 x I/O Shields

Application DVD Support DVD

Documentation User Guide

If any of the above items is damaged or missing, contact your retailer.

J1800I-A specications summary

CPU Intel® Celeron® Dual-core Processor J1800

Memory 2 x SO-DIMM DDR3L 1333 MHz, Max 8GB, non-ECC, un-buffered memory

Dual-channel memory architecture

* Hyper DIMM support is subject to the physical characteristics of individual

CPUs. Please refer to Memory QVL for details.

** Refer to

www.asus.com for the latest Memory QVL (Qualied Vendors List).

Graphics Integrated Graphics Processor- Intel® HD Graphics support

Multi-VGA output support: HDMI, D-Sub port

- Supports HDMI with max. resolution of 1920x1080@60Hz

- Supports D-sub with max. resolution of 2560x1600@60Hz

- Maximum shared memory of 512MB

* With DX11, OpenCL 1.1, OpenGL 4.0 ES Halt/2.0/1.1, OGL 3.2 support ** Support H.264, MPEG2, MVC, VC-1, WMV9 and VP9 decode acceleration

Expansion slots 1 x PCI

Storage Intel® Celeron® Dual-core Processor J1800

2 x SATA 3.0Gb/s connectors

LAN

Audio Realtek® ALC887 8-channel High Denition Audio CODEC

USB Intel® Celeron® Dual-core Processor J1800

Realtek® 8111G PCIe Gigabit LAN controller

- Supports Jack-Detection, and Front Panel Jack-Retasking

• Use a chassis with HD audio module in the front panel to support an 8-channel audio output.

1 x USB 3.0/2.0 ports at back panel (blue)

2 x USB 2.0/2.0 ports at back panel

GL852G USB Hub

4 x USB 2.0 ports at mid-board for front panel support

(continued on the next page)

J1800I-A specications summary

ASUS Unique Features

ASUS Exclusive Features

- ASUS Anti-surge Protection

- ASUS AI Suite 3

- ASUS USB 3.0 Boost

- ASUS Network iControl

ASUS Quiet Thermal Solution

- ASUS Fan Xpert

ASUS EZ DIY

- ASUS UEFI BIOS (EZ Mode)

- ASUS MyLogo 2

- ASUS EZ-FLash 2

- ASUS Crash Free BIOS3

100% All High-quality Conductive Polymer Capacitors

Back Panel I/O Ports 1 x PS/2 keyboard port (purple)

1 x PS/2 mouse port (green)

1 x HDMI port

1 x D-Sub port

1 x Printer port

1 x USB 3.0/2.0 ports

2 x USB 2.0/1.1 ports

1 x LAN (RJ-45) port

3 x Audio jacks support 8-channel audio output

Internal I/O Connectors

BIOS features 64Mb Flash ROM, UEFI AMI BIOS, PnP, DMI2.0, WfM2.0,SM BIOS 2.7,

2 x USB 2.0/1.1 connectors support additional 4 USB 2.0/1.1 ports

2 x SATA 3.0Gb/s connectors

1 x CPU fan connector

1 x Chassis fan connector

1 x Chassis intrusion connector

1 x Front panel audio connector

1 x COM connector

1 x TPM connector

1 x 24-pin EATX power connector

1 x 4-pin EATX 12V power connector

1 x Speaker connector

1 x System panel connector

ACPI 2.0a, Multi-language BIOS, ASUS EZ Flash 2, ASUS CrashFree

BIOS 3, My Favorites, Quick Note, Last Modied log, F12 PrintScreen,

F3 Shortcut functions and ASUS DRAM SPD (Serial Presence Detect) memory information

(continued on the next page)

vii

J1800I-A specications summary

Manageability

Accessories User manual

Support DVD Drivers

Form factor

Specications are subject to change without notice.

Wfm 2.0, DMI 2.0, WOL by PME, PXE

I/O shield

2 x Serial ATA 3.0Gb/s cables

ASUS utilities

EZ Update

Anti-virus software (OEM version)

Mini ITX Form Factor, 6.7” x 6.7” (17cm x 17cm)

viii

Product introduction

J1800I-A

J1800I-A Onboard LED

SB_PWR

Standby Power

Powered Off

OFF

1.1 Before you proceed

Take note of the following precautions before you install motherboard components or change any motherboard settings.

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.

• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, or components.

Standby Power LED

The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.

ASUS J1800I-A

1-1

J1800I-A

1.2 Motherboard overview

Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.

Ensure that you unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components.

1.2.1 Placement direction

When installing the motherboard, ensure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.

1.2.2 Screw holes

Place four screws into the holes indicated by circles to secure the motherboard to the chassis.

Do not overtighten the screws! Doing so can damage the motherboard.

Place this side towards

the rear of the chassis

1-2

Chapter 1: Product introduction

1.2.3 Motherboard layout

J1800I-A

F_PANEL

ASM1083

PCI1

AAFP

USBPWF

CHA_FAN

CPU_FAN

ALC 887

AUDIO

LPT

VGA

HDMI

RTL

8111G

17cm(6.7in)

SATA3G_2SATA3G_1

SPEAKER

Super

I/O

DDR3 DIMM_A1 (64bit, 204-pin module)

DDR3 DIMM_B1 (64bit, 204-pin module)

CPU

USB_E12 USB_E34

SB_PWR

EATXPWR

ATX12V

KBMS

LAN_USB23

USB3_1

CLRTC

USBPWB

KBPWR

CHASSIS

BATTERY

TPM

COM

8Mb BIOS

32 4 65 7 81

15 14 13

16 12 11

1.2.4 Layout contents

Connectors/Jumpers/Slots/LED Page

1. Keyboard power (3-pin KBWR) 1-10

2. Keyboard and USB device wake up (3-pin USBPWB) 1-10

3. CPU and chassis fan connectors (4-pin CPU_FAN and 4-pin CHA_FAN) 1-15

4. COM port connector (10-1 pin COM) 1-13

5. Chassis intrusion connector (4-1 pin CHASSIS) 1-14

6. Clear RTC RAM (3-pin CLRTC) 1-9

7. DDR3 SO-DIMM sockets 1-6

8. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) 1-14

9. Speaker connector (4-pin SPEAKER) 1-17

10. Serial ATA 3.0Gb/s connectors (7-pin SATA3G1~2) 1-16

11. System panel connector (10-1 pin F_PANEL) 1-17

12. Intel® Celeron Dual-core Processor J1800 1-4

13. USB 2.0 connectors (10-1 pin USB_E12, USB_E34) 1-15

14. TPM connector (20-1 TPM) 1-16

15. USB device wake up (3-pin USBPWF) 1-10

16. Standby power LED (SB_PWR) 1-1

17. Front panel audio connector (10-1 pin AAFP) 1-13

ASUS J1800I-A

1-3

1.3 Central Processing Unit (CPU)

J1800I-A

J1800I-A CPU

CPU

J1800I-A

J1800I-A 204-pin DDR3 DIMM sockets

DIMM_A1

DIMM_B1

The motherboard comes with an onboard Intel® Celeron™ Dual-core Processor J1800 and a specially designed CPU heatsink.

1.4 System memory

1.4.1 Overview

This motherboard comes with two Double Data Rate 3 (DDR3) Small Outline Dual Inline

Memory Modules (SO-DIMM) sockets. The gure illustrates the location of the DDR3 DIMM

sockets:

Channel Sockets

Channel A DIMM_A1

Channel B DIMM_B1

• Using both memory channels is supported on this motherboard. When installing 2 SO-

DIMMs, use the same size and type of memory. The DIMM_A1 slot should be lled in

order for the motherboard to work properly.

• This model supports a maximum total memory of of 8GB DDR3 1333 only. Memory

modules with a voltage higher than 1.35V will run at 1.35V. DDR3 1066Mhz memory

modules are not supported.

1.4.2 Memory congurations

You may install 512MB, 1GB, 2GB, 4GB and 8GB unbuffered non-ECC DDR3 SO-DIMMs into the DIMM sockets.

• Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor.

• This motherboard does not support DIMMs made up of 256 megabits (Mb) chips or less.

1-4

Chapter 1: Product introduction

J1800I-A Series Motherboard Qualied Vendors Lists (QVL)

DDR3-1333 MHz capability

Vendors Part No. Size

Corsair CMSO2GX3M1A1333C9 2GB DS Corsair 256M8DCJG - -

G.Skill F3-10666CL9S-2GBSQ 2GB DS G.Skill D3 256M8GEF

G.Skill F3-10666CL9S-4GBSQ 4GB DS G.Skill D3 256M8GEF

GEIL GS31GB1333C9SC 1GB DS GEIL

Kingmax FSFE85F-C8KM9-NBE 2GB DS Kingmax

Kingmax FSFF65F-C8KM9-NAE 4GB DS Kingmax

Kingston KVR1333D3S9/1G 1GB DS Elpida

Kingston KVR1333D3S9/2G 2GB DS KTC

SS/DSChip

Brand

Chip No. Timing Voltage

9-9-9-

24 9-9-9-

GL1L128M88 BA15B KFC8FNMXFBXX-15A KFC8FNMXFBXX-15A J1108BDBGDJ-F D1288JPND PLD9U

24 9-9-9-

1.5V

- -

1.5V

DIMM socket support (optional) 1DIMM 2DIMMs

ASUS J1800I-A

1-5

DDR3-1600 MHz capability

DIMM socket

Vendors Part No. Size

CMSX8GX3M2A

Corsair

1600C9 CMSO16GX3M2A

Corsair

1600C11 CMSX16GX3M2A

Corsair

1600C10

G.Skill F3-1600C11D-8GSL 4GB DS - K4B2G0846C

G.Skill F3-1600C11D-16GSL 8GB DS - K4B4G0846B

G.Skill F3-1600C11S-8GSQ 8GB DS Elpida J4208EASE-DJ-F

G.Skill F3-2133C11S-8GSQ 8GB DS Elpida 11480W11820 - 1.5V

GEIL GGS38GB1600C11DC 4GB DS Hynix H5TQ2G83CFR

KHX1600C9S3P1

Kingston

K2/8G

Kingston KVR16LS11/4 4GB DS Nanya NT5CC512M8CN-DI - 1.35V Kingston KVR16S11/8 8GB DS Elpida J4208BBBG-GN-F - 1.5V

Kingston KVR16S11/8 8GB DS Elpida J4208BBBG-GN-F - 1.5V PSC ASAF8L93B-GN2E 8GB DS PSC XHRO54C3G-M - -

M473B5773DHO-YKO

Samsung

1224 M473B5773DHO-YKO

Samsung

1251

ADATA ADDS1600W4G11-B 4GB DS AData

ADATA ADDS1600W8G11-B 8GB DS AData

Team TED38G1600C11-SBK 8GB DS Team T3D5148KT-16

SS/DSChip

4GB DS - PEB12-15E - -

8GB DS Corsair

8GB DS - PEB12-15E - -

4GB DS Hynix

2GB DS - K4B2G0864D - -

2GB DS - GEHXB8A3C - 1.35V

Chip No. Timing Voltage

Brand

512M BDCJGNACO3O1320

H5TQ2G83CFR PBC

QWND-1211AEL 1329V QWND-1211AEL 1329V

- -

11-1111-28 11-1111-28 11-1111

11-1111-28

- 1.5V

- 1.35V

11-1111-28

support (optional)

1DIMM 2DIMMs

1.35V

1.5V

1.3V

1-6

Chapter 1: Product introduction

SS: Single-sided / DS: Double-sided

DIMM support:

• A*:

Supports one module inserted into either slot.

• B*:

Supports one pair of modules inserted into both the slots.

• Using both memory channels is supported on this motherboard. When installing 2

SO-DIMMs, use the same size and type of memory. The DIMM_A1 slot should be lled in order for the motherboard to work properly.

•

Memory modules with a voltage higher than 1.35V will run at 1.35V.

• When installing memory with frequency higher than 1333Mhz, the motherboard will automatically run the memory at 1333Mhz. DDR3 1066Mhz memory modules are not

supported.

Visit the ASUS website at www.asus.com for the latest QVL.

ASUS J1800I-A

1-7

1.5 Expansion slots

In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.

Unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

1.5.1 Installing an expansion card

To install an expansion card:

1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.

2. Remove the system unit cover (if your motherboard is already installed in a chassis).

3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.

4. Align the card connector with the slot and press rmly until the card is completely

seated on the slot.

5. Secure the card to the chassis with the screw you removed earlier.

6. Replace the system cover.

1.5.2 Conguring an expansion card

After installing the expansion card, congure it by adjusting the software settings.

1. Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for information on BIOS setup.

2. Assign an IRQ to the card.

3. Install the software drivers for the expansion card.

1.5.3 PCI slot

The PCI slot supports cards such as a LAN card, SCSI card, USB card, and other cards that

comply with PCI specications.

IRQ assignments for this motherboard

Component A B C D E F G H

SATA Controller – – – shared – – – –

HD Audio – – – – – – shared –

USB 3.0 – – – – shared – – –

USB 2.0 – – – – – – – shared

LAN – shared – – – – – –

PCI1 – – shared – – – – –

1-8

Chapter 1: Product introduction

1.6 Jumpers

J1800I-A

J1800I-A Clear RTC RAM

1 2

2 3

Normal

(Default)

Clear RTC

CLRTC

1. Clear RTC RAM (3-pin CLRTC)

This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5-10 seconds, then move the cap back to pins 1-2.

3. Plug the power cord and turn ON the computer.

4. Hold down the < enter data.

Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure!

Del> key during the boot process and enter BIOS setup to re-

ASUS J1800I-A

• If the steps above do not help, remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.

• You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature. Shut down and reboot the system, then the BIOS automatically resets parameter settings to default values.

1-9

J1800I-A

1 2

2 3

+5V

(Default)

+5VSB

KBPWR

J1800I-A Keyboard Power Setting

J1800I-A

J1800I-A Keyboard and USB device wake up

1 2 2 3

+5V

+5VSB

(Default)

USBPWB

J1800I-A

J1800I-A USB device wake up

2 3

+5V

(Default)

+5VSB

USBPWF

2. Keyboard power (3-pin KBPWR)

This jumper allows you to enable or disable the keyboard wake-up feature. When you set this jumper to pins 2–3 (+5VSB), you can wake up the computer by pressing a key on the keyboard. This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS.

3. Keyboard and USB device wake up (3-pin USBPWB)

Set this jumper to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode).

4. USB device wake-up (3-pin USBPWF)

1-10

Chapter 1: Product introduction

1.7 Connectors

4 52

610

789

1.7.1 Rear panel connectors

1. PS/2 Mouse port. This port is for a PS/2 mouse.

2. LAN (RJ-45) port.

through a network hub. Refer to the table below for the LAN port LED indications.

LAN port LED indications

This port allows Gigabit connection to a Local Area Network (LAN)

LED

LAN port

Speed

LED

Activity/Link LED Speed LED

Activity Link

Status Description Status Description

OFF No link OFF 10Mbps connection ORANGE Linked ORANGE 100Mbps connection BLINKING Data activity GREEN 1Gbps connection

3. Parallel port. This port is for LPT printers that use a parallel connector.

4. Line In port (light blue). This port connects to a tape, CD, DVD player, or other audio

source.

5. Line Out port (lime).

This port connects to a headphone or a speaker. In the 4.1, 5.1,

and 7.1-channel congurations, the function of this port becomes Front Speaker Out.

6. Microphone port (pink).

Refer to the audio conguration table for the function of the audio ports in a 2.1, 4.1, 5.1 or

7.1-channel conguration.

This port connects to a microphone.

Audio 2.1, 4.1, 5.1 or 7.1-channel conguration

Port

Light Blue

(Rear panel)

Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out

Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center

Lime (Front panel) — — — Side Speaker Out

Headset

2.1-channel

Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out

4.1-channel 5.1-channel 7.1-channel

ASUS J1800I-A

1-11

+ 43 hidden pages