ASRock Z68M User Manual [en, ru, de, es, fr, it]

Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identifi ca- tion or explanation and to the owners’ benefi t, without intent to infringe.
Disclaimer:
Specifi cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or condi­tions of merchantability or fi tness for a particular purpose. In no event shall ASRock, its directors, offi cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profi ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published July 2011
Copyright©2011 ASRock INC. All rights reserved.
ASRock Z68M/USB3 Motherboard

English

1
Motherboard Layout
English
1
3
2
4
21.8cm (8.6in)
Keyboard
PS2
USB2.0 T:USB0 B:USB1
VGA1
DVI_CON1
CPU_FAN1
Gigabit LAN
HDMI1
USB3.0 T: US B2 B:USB3
33
USB2.0
Top:
T:USB4
RJ-45
B:USB5
LAN PHY
Top:
CTR BASS
Center:
REAR SPK
Bottom:
Optical
SPDIF
Bottom:
MIC IN
Top:
LINE IN
Center:
FRONT
32
31
HDMI 1.4a
Super
I/O
30
AUDIO
29 28
CODEC
HDMI_SPDIF1
1
COM1
HD_AUDIO1
1
1
27
26
PCIE2
PCIE3
FLOPPY1
PWR_FAN1
PCI1
25
ATX12V1
CMOS
Battery
PCIE1
PCI Express2.0
ErP/EuP Ready
1
LPT1
Designed inTaipei
Z68M/USB3
Intel
Z68
1
1
24
RoHS
USB6_7
23
DX10.1 DDR3
CIR1
22
1
SPEAKER1
21
DDR3_A1 (64bit, 240-pin module)
Dual Channel
SATA3 6Gb/s
1
1
20
DDR3_B1 (64bit, 240-pin module)
IR1
SATA2_3 SATA2_2
SATA2_5 SATA2_4
USB8_9
1
USB10_11
PLEDPWRBTN
1
HDLED RESET
19
1
1
CLRCMOS1
64Mb BIOS
PLED1
18
ATXPWR1
SATA3_0
SATA3_1
CHA_FAN1
PANEL1
24.4cm (9.6in)
5
6
7
8
9
10
11 12
13
14
15
16 17
1 CPU Fan Connector (CPU_FAN1) 19 USB 2.0 Header (USB10_11, Blue) 2 ATX 12V Power Connector (ATX12V1) 20 USB 2.0 Header (USB8_9, Blue) 3 1155-Pin CPU Socket 21 Chassis Speaker Header 4 2 x 240-pin DDR3 DIMM Slots (SPEAKER 1, White) (Dual Channel: DDR3_A1, DDR3_B1, Blue) 22 USB 2.0 Header (USB6_7, Blue) 5 ATX Power Connector (ATXPWR1) 23 Consumer Infrared Module Header 6 Infrared Module Header (IR1) (CIR1) 7 SATA3 Connector (SATA3_0, White) 24 Print Port Header (LPT1, White) 8 SATA3 Connector (SATA3_1, White) 25 Floppy Connector (FLOPPY1) 9 Clear CMOS Jumper (CLRCMOS1) 26 COM Port Header (COM1) 10 64Mb SPI Flash 27 Front Panel Audio Header 11 Intel Z68 Chipset (HD_AUDIO1, White) 12 SATA2 Connector (SATA2_3, Blue) 28 HDMI_SPDIF Header 13 SATA2 Connector (SATA2_2, Blue) (HDMI_SPDIF1, White) 14 SATA2 Connector (SATA2_4, Blue) 29 PCI Slot (PCI1) 15 SATA2 Connector (SATA2_5, Blue) 30 PCI Express 2.0 x1 Slot (PCIE3, White) 16 Power LED Header (PLED1) 31 PCI Express 2.0 x1 Slot (PCIE2, White) 17 Chassis Fan Connector (CHA_FAN1) 32 PCI Express 2.0 x16 Slot (PCIE1, Blue) 18 System Panel Header (PANEL1, White) 33 Power Fan Connector (PWR_FAN1)
2
ASRock Z68M/USB3 Motherboard
I/O Panel
1 USB 2.0 Ports (USB01) ** 8 Front Speaker (Lime) 2 D-Sub Port 9 Microphone (Pink) * 3 LAN RJ-45 Port 10 USB 2.0 Ports (USB45) 4 Central / Bass (Orange) 11 USB 3.0 Ports (USB23) 5 Rear Speaker (Black) 12 HDMI Port 6 Optical SPDIF Out Port 13 DVI-D Port 7 Line In (Light Blue) 14 PS/2 Keyboard Port (Purple)
* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
Activity/Link LED SPEED LED
Status Description Status Description
Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
LAN Port LED Indications
ACT/LINK LED
LAN Port
SPEED LED
If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.
**
See the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Line In or (No. 8) (No. 5) (No. 4) Side Speaker (No. 7)
2 V -- -- -­4 V V -- -­6 V V V -­8 V V V V
3
ASRock Z68M/USB3 Motherboard
English
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will fi nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.
English
4
ASRock Z68M/USB3 Motherboard
1. Introduction
Thank you for purchasing ASRock Z68M/USB3 motherboard, a reliable mother­board produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-by­step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.
Because the motherboard specifi cations and the BIOS software might be updated, the content of this manual will be subject to change without no­tice. In case any modifi cations of this manual occur, the updated version will be available on ASRock website without further notice. You may fi nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specifi c information about the model you are using. www.asrock.com/support/index.asp
1.1 Package Contents
ASRock Z68M/USB3 Motherboard (Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm) ASRock Z68M/USB3 Quick Installation Guide ASRock Z68M/USB3 Support CD 2 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield
ASRock Reminds You...
To get better performance in Windows® 7 / 7 64-bit / Vista bit, it is recommended to set the BIOS option in Storage Confi guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.
TM
/ VistaTM 64-
ASRock Z68M/USB3 Motherboard
English
5
English
1.2 Specifications
Platform - Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm
- All Solid Capacitor design CPU - Supports 2nd Generation Intel LGA1155 Package
- 4 + 2 Power Phase Design
- Supports Intel
®
Turbo Boost 2.0 Technology
- Supports K-Series unlocked CPU
- Supports Hyper-Threading Technology (see CAUTION 1) Chipset - Intel
®
Z68
Memory - Dual Channel DDR3 Memory Technology (see CAUTION 2)
- 2 x DDR3 DIMM slots
- Supports DDR3 2133(OC)/1866(OC)/1600/1333/1066 non-ECC, un-buffered memory
- Max. capacity of system memory: 16GB (see CAUTION 3)
- Supports Intel
®
Extreme Memory Profi le (XMP)
Expansion Slot - 1 x PCI Express 2.0 x16 slot (blue @ x16 mode)
- 2 x PCI Express 2.0 x1 slots
- 1 x PCI slot Graphics - Supports Intel
®
HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel
®
HD Graphics 2000/3000, Intel® Advanced
Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- Max. shared memory 1759MB (see CAUTION 4)
- Three VGA Output options: D-Sub, DVI-D and HDMI (see CAUTION 5)
- Supports HDMI 1.4a Technology with max. resolution up to 1920x1200 @ 60Hz
- Supports DVI with max. resolution up to 1920x1200 @ 60Hz
- Supports D-Sub with max. resolution up to 2048x1536 @ 75Hz
- Supports Auto Lip Sync, xvYCC and HBR (High Bit Rate Audio) with HDMI (Compliant HDMI monitor is required) (see CAUTION 6)
- Supports HDCP function with DVI and HDMI ports
- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with DVI and HDMI ports Audio - 7.1 CH HD Audio with Content Protection (Realtek ALC892 Audio Codec)
®
CoreTM i7 / i5 / i3 in
6
ASRock Z68M/USB3 Motherboard
- Premium Blu-ray audio support
- Supports THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supports Wake-On-LAN
- Supports LAN Cable Detection
- Supports Energy Effi cient Ethernet 802.3az
- Supports PXE Rear Panel I/O I/O Panel
- 1 x PS/2 Keyboard Port
- 1 x D-Sub Port
- 1 x DVI-D Port
- 1 x HDMI Port
- 1 x Optical SPDIF Out Port
- 4 x Ready-to-Use USB 2.0 Ports
- 2 x Ready-to-Use USB 3.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
- HD Audio Jack: Rear Speaker/Central/Bass/Line in/Front Speaker/Microphone (see CAUTION 7) SATA 3 - 2 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage and Intel Smart Response Technology), NCQ, AHCI and Hot Plug functions USB3.0 - 2 x USB 3.0 ports by Etron EJ168A, support USB 1.0/2.0/3.0 up to 5Gb/s Connector - 4 x SATA2 3.0 Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage and Intel Smart Response Technology), NCQ, AHCI and Hot Plug functions
- 2 x SATA3 6.0Gb/s connectors
- 1 x Floppy connector
- 1 x IR header
- 1 x CIR header
- 1 x Print port header
- 1 x COM port header
- 1 x HDMI_SPDIF header
- 1 x Power LED header
- CPU/Chassis/Power FAN connector
- 24 pin ATX power connector
- 8 pin 12V power connector
- Front panel audio connector
ASRock Z68M/USB3 Motherboard
English
7
English
- 3 x USB 2.0 headers (support 6 USB 2.0 ports) BIOS Feature - 64Mb AMI BIOS
- AMI UEFI Legal BIOS with GUI support
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, ASRock Software Suite (CyberLink DVD Suite - OEM and Trial; ASRock MAGIX Multimedia Suite - OEM) Unique Feature - ASRock Extreme Tuning Utility (AXTU) (see CAUTION 8)
- ASRock Instant Boot
- ASRock Instant Flash (see CAUTION 9)
- ASRock APP Charger (see CAUTION 10)
- ASRock SmartView (see CAUTION 11)
- ASRock XFast USB (see CAUTION 12)
- ASRock XFast LAN (see CAUTION 13)
- Lucid Virtu (see CAUTION 14)
- Hybrid Booster:
- CPU Frequency Stepless Control (see CAUTION 15)
- ASRock U-COP (see CAUTION 16)
- Boot Failure Guard (B.F.G.)
- Combo Cooler Option (C.C.O.) (see CAUTION 17)
- Good Night LED Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing
- CPU/Chassis/Power Fan Tachometer
- CPU/Chassis Quiet Fan (Allow Chassis Fan Speed Auto-Adjust by CPU Temperature)
- CPU Fan Multi-Speed Control
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore OS - Microsoft
®
Windows® 7 / 7 64-bit / Vista
TM
/ VistaTM 64-bit
/ XP / XP 64-bit compliant Certi cations - FCC, CE, WHQL
- ErP/EuP Ready (ErP/EuP ready power supply is required) (see CAUTION 18)
* For detailed product information, please visit our website: http://www.asrock.com
8
ASRock Z68M/USB3 Motherboard
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using the third-party overclocking tools. Overclocking may affect your system stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
CAUTION!
1. About the setting of “Hyper Threading Technology”, please check page 48 of “User Manual” in the support CD.
2. This motherboard supports Dual Channel Memory Technology. Before you implement Dual Channel Memory Technology, make sure to read the installation guide of memory modules on page 15 for proper installation.
3. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows VistaTM / XP. For Windows® OS with 64-bit CPU, there is no such limita­tion.
4. The maximum shared memory size is defi ned by the chipset vendor and is subject to change. Please check Intel
®
website for the latest informa-
tion.
5. You can choose to use two of the three monitors only. D-Sub, DVI-D and­HDMI monitors cannot be enabled at the same time. Besides, with the DVI-to-HDMI adapter, the DVI-D port can support the same features as HDMIport.
6. xvYCC and Deep Color are only supported under Windows
7. Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows® 7 64-bit / 7 / VistaTM 64-bit /
TM
Vista
.
7. For microphone input, this motherboard supports both stereo and mono modes. For audio output, this motherboard supports 2-channel, 4-chan­nel, 6-channel, and 8-channel modes. Please check the table on page 3 for proper connection.
8. ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to fi ne-tune different system functions in a user-friendly interface, which is including Hardware Monitor, Fan Control, Overclocking, OC DNA and IES. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a profi le and share with your friends. Your friends then can load the OC profi le to their own system to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve effi ciency when the CPU cores are idle without
®
®
7 64-bit /
7 /
English
ASRock Z68M/USB3 Motherboard
9
English
sacrificing computing performance. Please visit our website for the
operation procedures of ASRock Extreme Tuning Utility (AXTU).
ASRock website: http://www.asrock.com
9. ASRock Instant Flash is a BIOS fl ash utility embedded in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems fi rst like MS-DOS or Windows
®
. With this utility, you can press <F6> key during the POST or press <F2> key to BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS fi le to your USB fl ash drive, fl oppy disk or hard
drive, then you can update your BIOS only in a few clicks without prepar-
ing an additional fl oppy diskette or other complicated fl ash utility. Please be noted that the USB fl ash drive or hard drive must use FAT32/16/12 fi le system.
10. If you desire a faster, less restricted way of charging your Apple devices, such as iPhone/iPod/iPad Touch, ASRock has prepared a wonderful
solution for you - ASRock APP Charger. Simply installing the APP Char-
ger driver, it makes your iPhone charged much quickly from your com­puter and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Sus­pend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience than ever.
ASRock website: http://www.asrock.com/Feature/AppCharger/index.asp
11.
SmartView, a new function of internet browser, is the smart start page for IE that combines your most visited web sites, your history, your Facebook friends and your real-time newsfeed into an enhanced view for a more personal Internet experience. ASRock motherboards are exclusively equipped with the SmartView utility that helps you keep in touch with friends on-the-go. To use SmartView feature, please make sure your OS version is Windows
®
7 / 7 64 bit / VistaTM / VistaTM 64 bit, and your browser version is IE8. ASRock website: http://www.asrock.com/Feature/
SmartView/index.asp
12. ASRock XFast USB can boost USB storage device performance. The performance may depend on the property of the device.
13. ASRock XFast LAN provides a faster internet access, which includes below benefits. LAN Application Prioritization: You can configure your application priority ideally and/or add new programs. Lower Latency in Game: After setting online game priority higher, it can lower the latency in game. Traffi c Shaping: You can watch Youtube HD video and download les simultaneously. Real-Time Analysis of Your Data: With the status window, you can easily recognize which data streams you are currently transferring.
14. With Lucid Virtu technology, you can enjoy benefi ts from both 3D perfor- mance of the discrete GPU and advanced media features of Intel
®
HD
graphics.
10
ASRock Z68M/USB3 Motherboard
15. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause the instability of the system or damage the CPU.
16. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the motherboard functions properly and unplug the power cord, then plug it back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC sys-
tem.
17. Combo Cooler Option (C.C.O.) provides the fl exible option to adopt three different CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. Please be noticed that notall the 775 and 1156 CPU Fan can be used.
18. EuP, stands for Energy Using Product, was a provision regulated by Eu­ropean Union to defi ne the power consumption for the completed system. According to EuP, the total AC power of the completed system shall be under 1.00W in off mode condition. To meet EuP standard, an EuP ready motherboard and an EuP ready power supply are required. According to Intel’s suggestion, the EuP ready power supply must meet the standard of 5v standby power effi ciency is higher than 50% under 100 mA current consumption. For EuP ready power supply selection, we recommend you checking with the power supply manufacturer for more details.
ASRock Z68M/USB3 Motherboard
English
11
2. Installation
Pre-installation Precautions
Take note of the following precautions before you install mother­board components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any
component. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the car­pet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded
antstatic pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the moth-
erboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.
2.1 CPU Installation
For the installation of Intel 1155-Pin CPU, please follow the steps below.
LoadPlate
LoadLever
English
12
ContactArray
1155-Pin Socket Overview
Before you insert the 1155-Pin CPU into the socket, please check if the CPU surface is unclean or if there is any bent pin on the socket. Do not force to insert the CPU into the socket if above situation is found. Other­wise, the CPU will be seriously damaged.
SocketBody
ASRock Z68M/USB3 Motherboard
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear retention tab.
Step 1-2. Rotate the load lever to fully open po-
sition at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open po-
sition at approximately 100 degrees.
Step 2. Remove PnP Cap (Pick and Place Cap).
1. It is recommended to use the cap tab to handle and avoid kicking off the PnP cap.
2. This cap must be placed if returning the motherboard for after service.
Step 3. Insert the 1155-Pin CPU:
Step 3-1. Hold the CPU by the edges where
are marked with black lines.
black line
Step 3-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two orientation key notches.
orientation key notch
Pin1
orientation key notch
1155-Pin CPU
For proper inserting, please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket.
alignment key
ASRock Z68M/USB3 Motherboard
alignment key
1155-Pin Socket
Pin1
English
13
Step 3-3. Carefully place the CPU into the
socket by using a purely vertical mo­tion.
Step 3-4. Verify that the CPU is within the sock-
et and properly mated to the orient keys.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS. Step 4-2. While pressing down lightly on load
plate, engage the load lever.
2.2 Installation of CPU Fan and Heatsink
For proper installation, please kindly refer to the instruction manuals of your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 1155-Pin CPU. Step 1. Apply thermal interface material onto center of
IHS on the socket surface.
ApplyThermal InterfaceMaterial
English
Step 2. Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the
Fancables on side closestto MB header
CPU fan connector on the motherboard (CPU_ FAN1, see page 2, No. 1).
Step 3. Align fasteners with the motherboard through-
holes.
Step 4. Rotate the fastener clockwise, then press
down on fastener caps with thumb to install
PressDown
and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise, the heatsink cannot be secured on the motherboard.
(4Places)
Step 5. Connect fan header with the CPU fan connector on the motherboard. Step 6. Secure excess cable with tie-wrap to ensure cable does not interfere with fan operation or contact other components.
Please be noticed that this motherboard supports Combo Cooler Option (C.C.O.), which provides the fl exible option to adopt three dif- ferent CPU cooler types, Socket LGA 775, LGA 1155 and LGA 1156. The white throughholes are for Socket LGA 1155/1156 CPU fan.
14
ASRock Z68M/USB3 Motherboard
Fastenerslots pointingstraight out
2.3 Installation of Memory Modules (DIMM)
This motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel configuration, you always need to install two identical (the same brand, speed, size and chip­type) memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology. Otherwise, it will operate at single channel mode.
1. It is not allowed to install a DDR or DDR2 memory module into
DDR3 slot;otherwise, this motherboard and DIMM may be damaged.
2. If you install only one memory module or two non-identical memory modules, it is unable to activate the Dual Channel Memory Technology.
3. Some DDR3 1GB double-sided DIMMs with 16 chips may not work on this motherboard. It is not recommended to install them on this motherboard.
Installing a DIMM
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
notch break
notch
break
damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
The DIMM only fi ts in one correct orientation. It will cause permanent
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
ASRock Z68M/USB3 Motherboard
English
15
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 1 PCI slot and 3 PCI Express slots on this motherboard. PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.
PCIE slots: PCIE2 / PCIE3 (PCIE x1 slot; White) is used for PCI Express cards with
x1 lane width cards, such as Gigabit LAN card, SATA2 card, etc.
PCIE1 (PCIE x16 slot; Blue) is used for PCI Express x16 lane width
graphics cards.
English
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis). Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use. Step 4. Align the card connector with the slot and press fi rmly until the card is
completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.
16
ASRock Z68M/USB3 Motherboard
2.5 Dual Monitor and Surround Display Features
Dual Monitor Feature
This motherboard supports dual monitor feature. With the internal VGA output sup­port (DVI-D, D-Sub and HDMI), you can easily enjoy the benefi ts of dual monitor feature without installing any add-on VGA card to this motherboard. This mother­board also provides independent display controllers for DVI-D, D-Sub and HDMI to support dual VGA output so that DVI-D, D-sub and HDMI can drive same or different display contents. To enable dual monitor feature, please follow the below steps:
1. Connect DVI-D monitor cable to DVI-D port on the I/O panel, connect D-Sub monitor cable to D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel.
D-Sub port
DVI-D port
HDMI port
2. If you have installed onboard VGA driver from our support CD to your system already, you can freely enjoy the benefi ts of dual monitor function after your system boots. If you haven’t installed onboard VGA driver yet, please install onboard VGA driver from our support CD to your system and restart your computer.
D-Sub, DVI-D and HDMI monitors cannot be enabled at the same time. You can only choose the combination: DVI-D + HDMI, DVI-D + D-Sub, or HDMI + D-Sub.
ASRock Z68M/USB3 Motherboard
English
17
Surround Display Feature
This motherboard supports surround display upgrade. With the internal VGA output support (DVI-D, D-Sub and HDMI) and external add-on PCI Express VGA cards, you can easily enjoy the benefi ts of surround display feature. Please refer to the following steps to set up a surround display environment:
1. Install the PCI Express VGA card on PCIE1 slot. Please refer to page 16 for proper expansion card installation procedures for details.
2. Connect DVI-D monitor cable to DVI-D port on the I/O panel, connect D-Sub monitor cable to D-Sub port on the I/O panel, or connect HDMI monitor cable to HDMI port on the I/O panel. Then connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA card on PCIE1 slot.
3. Boot your system. Press <F2> or <Del> to enter BIOS setup. Enter “Onboard VGA Share Memory” option to adjust the memory capability to [32MB], [64MB], [128MB], [256MB] or [512MB] to enable the function of D-sub. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the BIOS setup, the default value of “Onboard VGA Share Memory”, [Auto], will disable D-Sub function when the add-on VGA card is inserted to this motherboard.
4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.
5. Set up a multi-monitor display.
English
For Windows
®
XP / XP 64-bit OS:
Right click the desktop, choose “Properties”, and select the “Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below. A. Click the “Identify” button to display a large number on each monitor. B. Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select “Primary”. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary. C. Select the display icon identifi ed by the number 2. D. Click “Extend my Windows desktop onto this monitor”. E. Right-click the display icon and select “Attached”, if necessary. F. Set the “Screen Resolution” and “Color Quality” as appropriate for the second monitor. Click “Apply” or “OK” to apply these new values. G. Repeat steps C through E for the diaplay icon identifi ed by the number one, two, three and four.
18
ASRock Z68M/USB3 Motherboard
For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Right click the desktop, choose “Personalize”, and select the “Display Settings” tab so that you can adjust the parameters of the multi-monitor according to the steps below. A. Click the number ”2” icon. B. Click the items “This is my main monitor” and “Extend the desktop onto this monitor”. C. Click “OK” to save your change. D. Repeat steps A through C for the display icon identifi ed by the number three and four.
6. Use Surround Display. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.
HDCP Function HDCP function is supported on this motherboard. To use HDCP function with this motherboard, you need to adopt the monitor that supports HDCP function as well. Therefore, you can enjoy the superior display quality with high-defi nition HDCP encryption contents. Please refer to below instruction for more details about HDCP function.
What is HDCP?
HDCP stands for High-Bandwidth Digital Content Protection, a specifi cation developed by Intel
®
for protecting digital entertainment content that uses the DVI interface. HDCP is a copy protection scheme to eliminate the possibility of intercepting digital data midstream between the video source, or transmitter - such as a computer, DVD player or set-top box ­ and the digital display, or receiver - such as a monitor, television or projector. In other words, HDCP specifi cation is designed to protect the integrity of content as it is being transmitted.
Products compatible with the HDCP scheme such as DVD players, satellite and cable HDTV set-top-boxes, as well as few entertainment PCs requires a secure connection to a compliant display. Due to the increase in manufacturers employing HDCP in their equipment, it is highly recommended that the HDTV or LCD monitor you purchase is compatible.
ASRock Z68M/USB3 Motherboard
English
19
2.6 ASRock Smart Remote Installation Guide
ASRock Smart Remote is only used for ASRock motherboard with CIR header. Please refer to below procedures for the quick installation and usage of ASRock Smart Remote.
Step1. Find the CIR header located next to the USB 2.0 header on ASRock motherboard.
USB 2.0 header (9-pin, blue)
CIR header (4-pin, white)
English
Step2. Connect the front USB cable to the USB 2.0 header (as below, pin 1-5) and the CIR header. Please make
USB_PWR
P-
P+
GND
DUMMY
sure the wire assignments and the pin assignments are matched correctly.
1
ATX+5VSB
2
IRRX
3
IRTX
4
GND
5
Step3. Install Multi-Angle CIR Receiver to the front USB port. If Multi-Angle
CIR Receiver cannot successfully
receive the infrared signals from MCE Remote Controller, please try to install it to the other front USB port.
3 CIR sensors in different angles
1. Only one of the front USB port can support CIR function. When the CIR function is enabled, the other port will remain USB function.
2. Multi-Angle CIR Receiver is used for front USB only. Please do
not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market.
3. The Multi-Angle CIR Receiver
function. Please install it before you boot the system.
* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www.asrock.com
does not support Hot-Plug
20
ASRock Z68M/USB3 Motherboard
2.7 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper Setting Description
Clear CMOS Jumper
(CLRCMOS1) (see p.2, No. 9)
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just fi nish updating the BIOS, you must boot up the system fi rst, and then shut it down before you do the clear-CMOS ac- tion. Please be noted that the password, date, time, user default profi le, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
ASRock Z68M/USB3 Motherboard
English
21
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
FDD connector
(33-pin FLOPPY1) (see p.2 No. 25)
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector.
English
Serial ATAII Connectors These four Serial ATAII
(SATA2_2: see p.2, No. 13)
(SATA2_3: see p.2, No. 12)
(SATA2_4: see p.2, No. 14)
(SATA2_5: see p.2, No. 15)
SATA2_3 SATA2_2
(SATAII) connectors support SATA data cables for internal storage devices. The current
SATA2_5 SATA2_4
SATAII interface allows up to
3.0 Gb/s data transfer rate.
Serial ATA3 Connectors These two Serial ATA3 (SATA3)
(SATA3_0: see p.2, No. 7)
(SATA3_1: see p.2, No. 8)
connectors support SATA data
SATA3_0
cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s
SATA3_1
data transfer rate.
Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the
(Optional)
SATA / SATAII / SATA3 hard disk or the SATAII / SATA3 connector on this motherboard.
22
ASRock Z68M/USB3 Motherboard
USB 2.0 Headers Besides four default USB 2.0
(9-pin USB6_7)
(see p.2 No. 22)
ports on the I/O panel, there
are three USB 2.0 headers on
this motherboard. Each USB 2.0 header can support two USB 2.0 ports.
(9-pin USB8_9) (see p.2 No. 20)
(9-pin USB10_11) (see p.2 No. 19)
1
1
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
P+9
P+8
P+11
P+10
GND
GND
GND
GND
DUMMY
DUMMY
Infrared Module Header This header supports an
(5-pin IR1)
optional wireless transmitting
(see p.2 No. 6)
and receiving infrared module.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Consumer Infrared Module Header This header can be used to
(4-pin CIR1)
(see p.2 No. 23)
Print Port Header This is an interface for print
(25-pin LPT1)
(see p.2 No. 24)
devices.
connect the remote
controller receiver.
AFD#
1
ERROR#
STB#
SPD0
port cable that allows
convenient connection of printer
PINIT#
SPD1
SLIN#
SPD2
SPD3
1
SPD4
IRRX
ATX+5VSB
GND
SPD6
SPD5
IRTX
SPD7
GND
ACK#
BUSY
PE
SLCT
English
ASRock Z68M/USB3 Motherboard
23
Front Panel Audio Header This is an interface for front
(9-pin HD_AUDIO1)
(see p.2 No. 27)
panel audio cable that allows
convenient connection and
control of audio devices.
1
GND
PRESENCE#
MIC2_R
MIC2_L
MIC_RET
J_SENSE
OUT2_R
OUT_RET
OUT2_L
1. High Defi nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. To activate the front mic. For Windows
Select “Mixer”. Select “Recorder”. Then click “FrontMic”.
For Windows
®
XP / XP 64-bit OS:
®
7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
Go to the "FrontMic" Tab in the Realtek Control panel. Adjust
“Recording Volume”.
System Panel Header This header accommodates
(9-pin PANEL1)
(see p.2 No. 18)
several system front panel
functions.
English
Connect the power switch, reset switch and system status indicator on the
chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may confi gure
the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset
switch to restart the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED): Connect to the power status indicator on the chassis front panel. The LED
is on when the system is operating. The LED keeps blinking when the sys­tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
24
ASRock Z68M/USB3 Motherboard
HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1)
(see p.2 No. 21)
speaker to this header.
Power LED Header Please connect the chassis
(3-pin PLED1)
(see p.2 No. 16)
power LED to this header to
indicate system power status.
1
PLED+
PLED+
PLED-
The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).
Chassis and Power Fan Connectors Please connect the fan cables
(3-pin CHA_FAN1)
(see p.2 No. 17)
to the fan connectors and
match the black wire to the
ground pin.
(3-pin PWR_FAN1) (see p.2 No. 33)
CPU Fan Connectors Please connect the CPU fan
(4-pin CPU_FAN1)
(see p.2 No. 1)
cable to the connector and
match the black wire to the
ground pin.
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
GND +12V CHA_FAN_SPEED
PWR_FAN_SPEED
+12V
GND
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Pin 1-3 Connected
3-Pin Fan Installation
English
ASRock Z68M/USB3 Motherboard
25
ATX Power Connector Please connect an ATX power
(24-pin ATXPWR1)
(see p.2 No. 5)
supply to this connector.
Though this motherboard provides 24-pin ATX power connector,
12 124
13
12
it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.
24
English
20-Pin ATX Power Supply Installation
ATX 12V Power Connector Please connect an ATX 12V
(8-pin ATX12V1)
(see p.2 No. 2)
power supply to this connector.
8 5
4 1
1
13
Though this motherboard provides 8-pin ATX 12V power connector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 5.
8 5
4-Pin ATX 12V Power Supply Installation
4 1
Serial port Header This COM1 header supports a
(9-pin COM1)
(see p.2 No. 26)
serial port module.
HDMI_SPDIF Header HDMI_SPDIF header, providing
(2-pin HDMI_SPDIF1)
(see p.2 No. 28)
SPDIF audio output to HDMI
VGA card, allows the system to
1
SPDIFOUT
GND
connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
26
ASRock Z68M/USB3 Motherboard
2.9 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive fi rst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.
2.10 Installing Windows® 7 / 7 64-bit / Vista
TM
/ VistaTM
64-bit / XP / XP 64-bit With RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64­bit on your SATA / SATAII / SATA3 HDDs with RAID functions, please refer to the document at the following path in the Support CD for detailed procedures:
..\ RAID Installation Guide
2.11 Installing Windows® 7 / 7 64-bit / Vista
TM
/ Vista
TM
64-bit / XP
/ XP 64-bit Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64­bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below procedures according to the OS you install.
2.11.1 Installing Windows® XP / XP 64-bit Without RAID Functions
If you want to install Windows® XP / XP 64-bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below steps.
Using SATA / SATAII / SATA3 HDDs without NCQ function
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY Advanced screen SATA Confi guration. B. Set the option “SATA Mode” to [IDE].
STEP 2: Install Windows
®
XP / XP 64-bit OS on your system.
ASRock Z68M/USB3 Motherboard
English
27
2.11.2 Installing Windows® 7 / 7 64-bit / Vista
TM
/ Vista
TM
64-bit
Without RAID Functions
If you want to install Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA / SATAII / SATA3 HDDs without RAID functions, please follow below steps.
Using SATA / SATAII / STA3 HDDs without NCQ function
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY Advanced screen SATA Confi guration. B. Set the option “SATA Mode” to [IDE].
STEP 2: Install Windows system.
Using SATA / SATAII / SATA3 HDDs with NCQ function
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY Advanced screen SATA Confi guration. B. Set the option “SATA Mode” to [AHCI].
STEP 2: Install Windows system.
®
7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your
®
7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your
English
28
ASRock Z68M/USB3 Motherboard
3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the prede­termined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF fi le) contained in the Support CD.
4. Software Support CD information
®
This motherboard supports various Microsoft 64-bit / VistaTM / Vista motherboard contains necessary drivers and useful utilities that will enhance moth­erboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the fi le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
TM
64-bit / XP / XP 64-bit. The Support CD that came with the
Windows® operating systems: 7 / 7
ASRock Z68M/USB3 Motherboard
English
29
1. Einführung
Wir danken Ihnen für den Kauf des ASRock Z68M/USB3 Motherboard, ein zuver­lässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnel­linstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard fi nden Sie in der Bedienungsanleitung auf der Support-CD.
Da sich Motherboard-Spezifi kationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafi kkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifi sche Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite: www.asrock.com/support/index.asp
1.1 Kartoninhalt
ASRock Z68M/USB3 Motherboard (Micro ATX-Formfaktor: 24.4 cm x 21.8 cm; 9.6 Zoll x 8.6 Zoll) ASRock Z68M/USB3 Schnellinstallationsanleitung ASRock Z68M/USB3 Support-CD Zwei Serial ATA (SATA) -Datenkabel (optional) Ein I/O Shield
Deutsch
30
ASRock erinnert...
Zur besseren Leistung unter Windows® 7 / 7, 64 Bit / Vista 64 Bit empfehlen wir, die Speicherkonfi guration im BIOS auf den AHCI- Modus einzustellen. Hinweise zu den BIOS-Einstellungen fi nden Sie in der Bedienungsanleitung auf der mitgelieferten CD.
TM
/ VistaTM
ASRock Z68M/USB3 Motherboard
1.2 Spezifikationen
Plattform - Micro ATX-Formfaktor: 24.4 cm x 21.8 cm; 9.6 Zoll x 8.6 Zoll
- Alle Feste Kondensatordesign CPU - Unterstützt Intel LGA1155-Paket
- 4 + 2-Stromphasendesign
- Unterstützt Intel
- Unterstützt freigegebene CPU der K-Serie
- Unterstützt Hyper-Threading-Technologie (siehe VORSICHT 1) Chipsatz - Intel
®
Z68
Speicher - Unterstützung von Dual-Kanal-Speichertechnologie (siehe VORSICHT 2)
- 2 x Steckplätze für DDR3
- Unterstützt DDR3 2133(OC)/1866(OC)/1600/1333/1066 non-ECC, ungepufferter Speicher
- Max. Kapazität des Systemspeichers: 16GB (siehe VORSICHT 3)
- Unterstützt Intel Erweiterungs- - 1 x PCI Express 2.0 x16-Steckplatz (blau für x16-Modus) steckplätze - 2 x PCI Express 2.0 x1-Steckplätze
- 1 x PCI -Steckplätze Onboard-VGA - Unterstützt hochaufl ösende integrierte Intel Intel® Quick-Sync-Video, Intel® InTruTM 3D, Intel® Clear­ Video-Technik (HD), Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- Maximal gemeinsam genutzter Speicher 1759MB (siehe VORSICHT 4)
- Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie HDMI (siehe VORSICHT 5)
- Unterstützt HDMI 1.4a mit einer maximalen Aufl ösung von 1920 x 1200 bei 60 Hz
- Unterstützt DVI mit einer maximalen Aufl ösung von 1920 x 1200 bei 60 Hz
- Unterstützt D-Sub mit einer maximalen Aufl ösung von 2048 x 1536 bei 75 Hz
- Unterstützt Auto Lip Sync, xvYCC und HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI-Bildschirm erforderlich) (siehe VORSICHT 6)
®
CoreTM (2te Generation) i7 / i5 / i3 im
®
Turbo Boost 2.0-Technologie
®
Extreme Memory Profi le (XMP)
®
-Grafi klösungen:
Deutsch
ASRock Z68M/USB3 Motherboard
31
Deutsch
32
- Unterstützt HDCP-Funktion mit DVI- und HDMI-Ports
- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit DVI- und HDMI-Ports Audio - 7.1 CH HD Audio mit dem Inhalt Schutz (Realtek ALC892 Audio Codec)
- Premium Blu-ray-Audio-Unterstützung
- Unterstützt THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Unterstützt Wake-On-LAN
- Unterstützt LAN-Kabelerkennung
- Unterstützt energieeffi zientes Ethernet 802.3az
- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Tastaturanschluss Rückseite - 1 x D-Sub port
- 1 x DVI-D port
- 1 x HDMI port
- 1 x optischer SPDIF-Ausgang
- 4 x Standard-USB 2.0-Anschlüsse
- 2 x Standard-USB 3.0-Anschlüsse
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass / Audioeingang / Lautsprecher vorne / Mikrofon (siehe VORSICHT 7) SATA3 - 2 x SATA 3-Anschlüsse (6,0 Gb/s); unterstützt RAID­ (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage und Intel Smart Response-Technologie), NCQ-, AHCI-und „Hot Plug“ (Hot-Plugging)-Funktionen USB3.0 - 2 x USB 3.0-Ports an der Rückseite durch Etron EJ168A, unterstützt USB 1.0/2.0/3.0 mit bis zu 5 Gb/s Anschlüsse - 4 x SATA2 3,0 GB/s-Anschlüsse, unterstützen RAID- (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage und Intel Smart Response-Technologie), NCQ-, AHCI-und „Hot Plug“ (Hot-Plugging)-Funktionen
- 2 x SATA3 6,0 GB/s-Anschlüsse
- 1 x FDD-Anschlüsse
- 1 x Infrarot-Modul-Header
- 1 x
Consumer Infrared-Modul-Header
- 1 x Druckerport-Anschlussleiste
- 1 x COM-Anschluss-Header
ASRock Z68M/USB3 Motherboard
- 1 x HDMI_SPDIF-Anschluss
- 1 x Betriebs-LED-Header
- CPU/Gehäuse/Stromlüfter-Anschluss
- 24-pin ATX-Netz-Header
- 8-pin anschluss für 12V-ATX-Netzteil
- Anschluss für Audio auf der Gehäusevorderseite
- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher USB 2.0-Anschlüsse) BIOS - 64Mb AMI BIOS
- AMIs Legal BIOS UEFI mit GUI-Unterstützung
- Unterstützung für “Plug and Play”
- ACPI 1.1-Weckfunktionen
- JumperFree-Übertaktungstechnologie
- SMBIOS 2.3.1
- IGPU, DRAM, PCH, CPU PLL, VTT, VCSA Stromspannung Multianpassung CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation), CyberLink MediaEspresso 6.5 Trial, Suite logicielle ASRock (CyberLink DVD Suite et Version OEM et d’essai; ASRock MAGIX-Multimedia-Suite - OEM)
Einzigartige - ASRock Extreme Tuning Utility (AXTU) (siehe VORSICHT 8) Eigenschaft - ASRock Sofortstart
- ASRock Instant Flash (siehe VORSICHT 9)
- ASRock APP Charger (siehe VORSICHT 10)
- ASRock SmartView (siehe VORSICHT 11)
- ASRock XFast USB (siehe VORSICHT 12)
- ASRock XFast LAN (siehe VORSICHT 13)
- Lucid Virtu (siehe VORSICHT 14)
- Hybrid Booster:
- Schrittloser CPU-Frequenz-Kontrolle (siehe VORSICHT 15)
- ASRock U-COP (siehe VORSICHT 16)
- Boot Failure Guard (B.F.G. – Systemstartfehlerschutz)
- Combo-Kühleroption (siehe VORSICHT 17)
- Gute Nacht-LED Hardware Monitor - Überwachung der CPU-Temperatur
- Motherboardtemperaturerkennung
- Drehzahlmessung für CPU/Gehäuse/Stromlüfter
- Geräuscharmer CPU-/Gehäuselüfter (ermöglicht die au tomatische Anpassung der Gehäuselüftergeschwindigkeit durch CPU-Temperatur)
- Mehrstufi ge Geschwindigkeitsteuerung für CPUlüfter
ASRock Z68M/USB3 Motherboard
Deutsch
33
Deutsch
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
®
Betriebssysteme - Unterstützt Microsoft Vista
TM
64-Bit / XP / XP 64-Bit
Windows® 7 / 7 64-Bit / VistaTM /
Zerti zierungen - FCC, CE, WHQL
- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich) (siehe VORSICHT 18)
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com
WARNUNG
Beachten Sie bitte, dass Overclocking, einschließlich der Einstellung im BIOS, Anwenden der Untied Overclocking-Technologie oder Verwenden von Overclocking­ Werkzeugen von Dritten, mit einem gewissen Risiko behaftet ist. Overclocking kann sich nachteilig auf die Stabilität Ihres Systems auswirken oder sogar Komponenten und Geräte Ihres Systems beschädigen. Es geschieht dann auf eigene Gefahr und auf Ihre Kosten. Wir übernehmen keine Verantwortung für mögliche Schäden, die aufgrund von Overclocking verursacht wurden.
VORSICHT!
1. Die Einstellung der “Hyper-Threading Technology”, fi nden Sie auf Seite 48 des auf der Support-CD enthaltenen Benutzerhandbuches beschrie­ben.
2. Dieses Motherboard unterstützt Dual-Kanal-Speichertechnologie. Vor Implementierung der Dual-Kanal-Speichertechnologie müssen Sie die Installationsanleitung für die Speichermodule auf Seite 15 zwecks
richtiger Installation gelesen haben.
3. Durch Betriebssystem-Einschränkungen kann die tatsächliche Speicher­größe weniger als 4 GB betragen, da unter Windows etwas Speicher zur Nutzung durch das System reserviert wird. Unter Windows® OS mit 64-Bit-CPU besteht diese Einschränkung nicht.
4. Die Maximalspeichergröße ist von den Chipshändler defi niert und umge- tauscht. Bitte überprüfen Sie Intel® website für die neuliche Information.
5. Sie können nur die Nutzung von zwei von drei Bildschirmen auswählen. Die D-Sub-, DVI-D- und HDMI-Bildschirme können nicht gleichzeitig aktiviert werden. Zudem kann der DVI-D-Port mit DVI-zu-HDMI-Adapter dieselben Funktionen wie der HDMI-Port unterstützen.
6. xvYCC und Deep Color werden nur unter Windows stützt. Der Deep Color-Modus wird nur aktiviert, wenn der Bildschirm 12bpc in EDID unterstützt. HBR wird unter Windows 64 Bit / VistaTM unterstützt.
7. Der Mikrofoneingang dieses Motherboards unterstützt Stereo- und Mono­Modi. Der Audioausgang dieses Motherboards unterstützt 2-Kanal-, 4-Kanal-, 6-Kanal- und 8-Kanal-Modi. Stellen Sie die richtige Verbindung anhand der Tabelle auf Seite 3 her.
®
7 / Vista™ / XP
®
7 64-Bit / 7 unter-
®
7 64 Bit / 7 / VistaTM
34
ASRock Z68M/USB3 Motherboard
8. ASRock Extreme Tuning Utility (AXTU) ist ein Alles-in-einem­Werkzeug zur Feineinstellung verschiedener Systemfunktionen an einer benutzerfreundlichen Schnittstelle; diese beinhaltet Hardware­Überwachung, Lüftersteuerung, Übertaktung, OC DNA und IES. Über die
Hardware-Überwachung können Sie die Hauptsystemdaten einsehen.
Die Lüftersteuerung zeigt Ihnen zur Anpassung Lüftergeschwindigkeit und Temperatur an. Bei der Übertaktung können Sie die CPU-Frequenz
zur Erzielung optimaler Systemleistung übertakten. OC DNA ermöglicht
Ihnen die Speicherung Ihrer OC-Einstellungen als Profi l, welches Sie mit Freunden teilen können. Ihre Freunde können das OC-Profi l dann in ihrem System laden und so die gleichen OC-Einstellungen erzielen. Per IES (Intelligent Energy Saver) kann der Spannungsregulator bei Inaktivität der CPU-Kerne die Anzahl an Ausgangsphasen zur Steigerung
der Effi zienz reduzieren – ohne die Rechenleistung zu beeinträchtigen.
Hinweise zur Bedienung der ASRock Extreme Tuning Utility (AXTU) nden Sie auf unserer Webseite.
ASRock-Webseite: http://www.asrock.com
9. ASRock Instant Flash ist ein im Flash-ROM eingebettetes BIOS-Flash­Programm. Mithilfe dieses praktischen BIOS-Aktualisierungswerkzeugs können Sie das System-BIOS aktualisieren, ohne dafür zuerst Betriebs­systeme wie MS-DOS oder Windows Programm bekommen Sie durch Drücken der <F6>-Taste
während des POST-Vorgangs oder durch Drücken der <F2>-Taste im
BIOS-Setup-Menü Zugang zu ASRock Instant Flash. Sie brauchen dieses Werkzeug einfach nur zu starten und die neue BIOS-Datei auf Ihrem
USB-Flash-Laufwerk, Diskettenlaufwerk oder der Festplatte zu speichern,
und schon können Sie Ihr BIOS mit nur wenigen Klickvorgängen ohne Bereitstellung einer zusätzlichen Diskette oder eines anderen kompli­zierten Flash-Programms aktualisieren. Achten Sie darauf, dass das USB-Flash-Laufwerk oder die Festplatte das Dateisystem FAT32/16/12 benutzen muss.
10. Wenn Sie nach einer schnelleren, weniger eingeschränkten Möglichkeit zur Aufl adung Ihrer Apple-Geräte (z. B. iPhone/iPad/iPod touch) suchen, bietet ASRock Ihnen eine wunderbare Lösung – den ASRock APP Char­ger. Installieren Sie einfach den ASRock APP Charger-Treiber;
dadurch lädt sich Ihr iPhone wesentlich schneller über einen Computer auf – genaugenommen bis zu 40 % schneller als zuvor. Der ASRock APP
Charger ermöglicht Ihnen die schnelle Aufl adung mehrerer Apple-Geräte
gleichzeitig; der Ladevorgang wird sogar dann fortgesetzt, wenn der PC
den Ruhezustand (S1), Suspend to RAM-Modus (S3) oder Tiefschlafmo­dus (S4) aufruft oder ausgeschaltet wird (S5). Nach der Installation des APP Charger-Treibers können Sie im Handumdrehen das großartigste Ladeerlebnis überhaupt genießen. ASRock-Webseite: http://www.asrock. com/Feature/AppCharger/index.asp
®
aufrufen zu müssen. Mit diesem
Deutsch
ASRock Z68M/USB3 Motherboard
35
Deutsch
11. SmartView, eine neue Internetbrowserfunktion, ist eine intelligente IE-
Startseite, die meist besuchte Internetseiten, Ihren Browserverlauf, Facebook-Freunde und Nachrichten in Echtzeit miteinander kombiniert: In einer speziellen Ansicht, die das Internet noch angenehmer und aufre­gender macht. ASRock-Motherboards werden exklusiv mit der Smart­View-Software geliefert, die auch dafür sorgt, dass Sie immer mit Ihren Freunden in Verbindung bleiben. Die SmartView-Funktionen können Sie mit den Windows und dem Internet Explorer ab Version 8 nutzen. ASRock-Website: http://
www.asrock.com/Feature/SmartView/index.asp
12. ASRocks XFast USB dient der Steigerung der Leistungsfähigkeit Ihrer USB-Speichergeräte. Die Leistung kann je nach Eigenschaften des Gerätes variieren.
13. ASRock XFast LAN bietet einen schnelleren Internetzugang mit den nachfolgenden Vorteilen. LAN-Anwendungspriorisierung: Hiermit kon­ gurieren Sie auf ideale Weise Ihre Anwendungspriorität und/oder fügen neue Programme hinzu. Niedrigere Latenzzeit bei Spielen: Nach Einstel­lung einer höheren Online-Gamepriorität kann hiermit die Latenzzeit bei Spielen herabgesetzt werden. Datenverkehrsgestaltung: Sie können Youtube-Videos in HD anzeigen und gleichzeitig Dateien herunterladen. Echtzeitanalyse Ihrer Daten: Über das Statusfenster können Sie schnell ermitteln, welche Datenströme zur Zeit übertragen werden.
14. Durch die Lucid Virtu-Technologie können Sie sowohl von der 3D-Leis­tung der separaten GPU als auch von den erweiterten Medienfunktionen der Intel
15. Obwohl dieses Motherboard stufenlose Steuerung bietet, wird Over­clocking nicht empfohlen. Frequenzen, die über den für den jeweiligen Prozessor vorgesehenen liegen, können das System instabil werden lassen oder die CPU beschädigen.
16. Wird eine Überhitzung der CPU registriert, führt das System einen au­tomatischen Shutdown durch. Bevor Sie das System neu starten,
prüfen Sie bitte, ob der CPU-Lüfter am Motherboard richtig funktioniert, und
stecken Sie bitte den Stromkabelstecker aus und dann wieder ein. Um die Wärmeableitung zu verbessern, bitte nicht vergessen, etwas Wärmeleit­paste zwischen CPU und Kühlkörper zu sprühen.
17. Die Combo-Kühleroption bietet die fl exible Möglichkeit zur Aufnahme von drei verschiedenen CPU-Kühlertypen, Socket LGA 775, LGA 1155 und LGA
1156. Beachten Sie bitte, dass nicht alle 775 und 1156 CPU-Lüfter verwen­det werden können.
18. EuP steht für Energy Using Product und kennzeichnet die Ökodesign-Richt­linie, die von der Europäischen Gemeinschaft zur Festlegung des Ener­gieverbrauchs von vollständigen Systemen in Kraft gesetzt wurde. Gemäß dieser Ökodesign-Richtlinie (EuP) muss der gesamte Netzstromverbrauch von vollständigen Systemen unter 1,00 Watt liegen,
wenn sie ausgeschaltet sind. Um dem EuP-Standard zu entsprechen, sind
ein EuP-fähiges Motherboard und eine EuP-fähige Stromversorgung erfor­derlich. Gemäß einer Empfehlung von Intel muss eine EuP-fähige
®
-Betriebssystemen 7 / 7, 64 Bit / VistaTM / VistaTM 64 Bit
®
HD-Grafi kkarte profi tieren.
36
ASRock Z68M/USB3 Motherboard
Stromversorgung dem Standard entsprechen, was bedeutet, dass bei
einem Stromverbrauch von 100 mA die 5-Volt-Standby-Energieeffi zienz höher als 50% sein sollte. Für die Wahl einer EuP-fähigen Stromversorgung empfehlen wir Ihnen, weitere Details beim Hersteller der Stromversorgung abzufragen.
1.3 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Ge­brückt” sind, bzw. es befi ndet sich eine Jumper-Kappe auf diesen beiden Pins.
Jumper Einstellun Beschreibung
CMOS löschen
(CLRCMOS1, 3-Pin jumper) (siehe S.2, No. 9)
Hinweis:
CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte aus und trennen das Netzkabel von der Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Uhrzeit, benutzerdefi niertes Profi l, 1394 GUID und MAC-Adresse
nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.
Default­Einstellung
CMOS löschen
ASRock Z68M/USB3 Motherboard
Deutsch
37
Deutsch
1.4 Integrierte Header und Anschlüsse
Anschluss für das Floppy-Laufwerk
(33-Pin FLOPPY1) (siehe S.2 - No. 25)
Hinweis: Achten Sie darauf, dass die rotgestreifte Seite des Kabel mit der Stift 1- Seite des Anschlusses verbunden wird.
Seriell-ATAII-Anschlüsse Diese vier Serial ATAII-
(SATA2_2: siehe S.2 - No. 13)
(SATA2_3: siehe S.2 - No. 12)
(SATA2_4: siehe S.2 - No. 14)
(SATA2_5: siehe S.2 - No. 15)
aktuelle SATAII-Schnittstelle ermöglicht eine Datenübertragungsrate bis 3,0 Gb/s.
Seriell-ATA3-Anschlüsse Diese zwei Serial ATA3-
(SATA3_0: siehe S.2 - No. 7)
(SATA3_1: siehe S.2 - No. 8)
für interne Massenspeichergeräte. Die
aktuelle SATA3- Schnittstelle ermöglicht eine Datenübertragungsrate bis 6,0 Gb/s.
Serial ATA- (SATA-) SJedes Ende des SATA Datenkabel Datenkabels kann an die SATA
(Option)
oder das SATAII / SATA3 Verbindungsstück auf dieser Hauptplatine angeschlossen werden.
Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KE­INE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jump­erkappen auf Header und Anschlüsse setzen, wird das Motherboard unreparierbar beschädigt!
(SATAII-)Verbínder
SATA2_3 SATA2_2
die rotgestreifte Seite auf Stift 1
unterstützten SATA-Datenkabel für interne
SATA2_5 SATA2_4
Massenspeichergeräte. Die
(SATA3-)Verbínder unterstützten SATA-Datenkabel
SATA3_0
SATA3_1
/ SATAII / SATA3 Festplatte
38
ASRock Z68M/USB3 Motherboard
USB 2.0-Header Zusätzlich zu den vier
(9-pol. USB6_7)
(siehe S.2 - No. 22)
üblichen USB 2.0-Ports an den
I/O-Anschlüssen befi nden sich drei USB 2.0- Anschlussleisten am Motherboard. Pro USB 2.0-
(9-pol. USB8_9)
(siehe S.2 - No. 20)
(9-pol. USB10_11) (siehe S.2 - No. 19)
Anschlussleiste werden zwei
USB 2.0-Ports unterstützt.
Infrarot-Modul-Header Dieser Header unterstützt ein
(5-pin IR1)
optionales, drahtloses Sende-
(siehe S.2 - No. 6)
und Empfangs-Infrarotmodul.
1
1
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
IRTX
1
IRRX
P+9
P+8
P+11
P+10
+5VSB
GND
GND
DUMMY
GND
GND
DUMMY
GND
DUMMY
Consumer Infrared-Modul-Header Dieser Header kann zum
(4-pin CIR1)
(siehe S.2 - No. 23)
Hi-Fi-Anlagen, TV-Boxen etc.
Anschließen optionaler
Consumer Infrared-Geräte wie
1
ATX+5VSB
IRRX
IRTX
GND
genutzt werden.
Druckerport-Anschlussleiste Dies ist eine Schnittstelle zum
(25-pol. LPT1)
(siehe S.2 - No. 24)
Anschluss eines Druckerport-
Kabels, mit dem Sie passende Drucker auf einfache Weise anschließen können.
Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorder
(9-Pin HD_AUDIO1)
(siehe S.2 - No. 27)
ermöglicht Ihnen eine bequeme
Anschlussmöglichkeit und Kontrolle über Audio-Geräte.
AFD#
ERROR#
PINIT#
SLIN#
1
SPD2
SPD1
SPD0
STB#
SPD3
SPD4
GND
GND
SPD7
SPD6
SPD5
PRESENCE#
MIC_RET
ACK#
OUT_RET
BUSY
PE
SLCT
seite Ihres Gehäuses,
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
Deutsch
39
ASRock Z68M/USB3 Motherboard
1. High Defi nition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an. B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an.
D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese
Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden. E. So aktivieren Sie das Mikrofon an der Vorderseite. Bei den Betriebssystemen Windows
Wählen Sie „Mixer“. Wählen Sie „Recorder“ (Rekorder). Klicken Sie dann auf „FrontMic“ (Vorderes Mikrofon). Bei den Betriebssystemen Windows Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)- Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke) an.
®
XP / XP 64 Bit:
®
7 / 7 64 Bit / VistaTM / VistaTM 64 Bit:
System Panel-Header Dieser Header unterstützt
(9-pin PANEL1)
(siehe S.2 - No. 18)
mehrere Funktion der
Systemvorderseite.
Deutsch
40
Schließen Sie die Ein-/Austaste, die Reset-Taste und die Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die positiven und negativen Pins, bevor Sie die Kabel anschließen.
PWRBTN (Ein-/Ausschalter):
Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu ses. Sie können konfi gurieren, wie das System mit Hilfe des Ein-/Ausschalters ausgeschaltet werden können soll.
RESET (Reset-Taste):
Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses. Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes neu starten.
PLED (Systembetriebs-LED):
Zum Anschließen der Betriebsstatusanzeige an der Frontblende des Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt, wenn sich das System im Ruhezustand S1 befi ndet. Die LED schaltet sich aus, wenn sich das System in den Modi S3/S4 befi ndet oder ausgeschaltet ist (S5).
ASRock Z68M/USB3 Motherboard
HDLED (Festplattenaktivitäts-LED):
Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variiere. Ein Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED, Lautsprechern, etc. Stellen Sie beim Anschließen des Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die Kabel- und Pinbelegung korrekt übereinstimmen.
Gehäuselautsprecher-Header Schließen Sie den
(4-pin SPEAKER1)
(siehe S.2 - No. 21)
Gehäuselautsprecher an
diesen Header an.
Betriebs-LED-Header Bitte schließen Sie die
(3-pin PLED1)
(siehe S.2 - No. 16)
Systembetriebsstatus an
Betriebs-LED des Gehäuses
zur Anzeige des
1
PLED+
PLED+
PLED-
diesem Header an. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt im S1-Zustand. Im S3-/S4- oder S5-Zustand (ausgeschaltet) leuchtet die LED nicht.
Gehäuse- und Stromlüfteranschlüsse
(3-pin CHA_FAN1)
(siehe S.2 - No. 17)
GND +12V CHA_FAN_SPEED
Verbinden Sie die Lüfterkabel mit den Lüfteranschlüssen, wobei der schwarze Draht an den Schutzleiterstift angeschlossen
(3-pin PWR_FAN1)
(siehe S.2 - No. 33)
PWR_FAN_SPEED
+12V
GND
wird.
CPU-Lüfteranschluss Verbinden Sie das CPU -
(4-pin CPU_FAN1)
(siehe S.2 - No. 1)
Lüfterkabel mit diesem
Anschluss und passen Sie den schwarzen Draht dem Erdungsstift an.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
ASRock Z68M/USB3 Motherboard
Deutsch
41
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss (Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den Pins 1 – 3.
Pins 1–3 anschließen
Lüfter mit dreipoligem Anschluss installieren
Deutsch
ATX-Netz-Header Verbinden Sie die ATX-
(24-pin ATXPWR1)
(siehe S.2 - No. 5)
Obwohl dieses Motherboard einen 24-pol. ATX-
Stromversorgung mit diesem
Header.
12 124
13
12
24
Stromanschluss bietet, kann es auch mit einem modifi zierten traditionellen 20-pol. ATX-Netzteil verwendet werden. Um ein 20-pol. ATX-Netzteil zu verwenden, stecken Sie den Stecker mit Pin 1 und Pin 13 ein.
ATX 12V Anschluss Bitte schließen Sie an diesen
(8-pin ATX12V1)
(siehe S.2 - No. 2)
Anschluss die ATX 12V
Stromversorgung an.
Installation eines 20-pol. ATX-Netzteils
8 5
4 1
1
13
Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur Verfügung stellt, kann sie noch arbeiten, wenn Sie einen traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die 4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.
Installation der 4-Pin ATX 12V Energieversorgung
8 5
4 1
COM-Anschluss-Header Dieser COM-Anschluss-
(9-pin COM1)
(siehe S.2 - No. 26)
Header wird verwendet, um
ein COM-Anschlussmodul zu
unterstützen.
42
ASRock Z68M/USB3 Motherboard
HDMI_SPDIF-Anschluss Der HDMI_SPDIF-Anschluss
(2-pin HDMI_SPDIF1)
(siehe S.2 - No. 28)
VGA-Karte zur Verfügung und
stellt einen SPDIF-
Audioausgang für eine HDMI-
1
SPDIFOUT
GND
ermöglicht den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten, Projektoren, LCD-Geräten an das System. Bitte verbinden Sie den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte mit diesem Anschluss.
ASRock Z68M/USB3 Motherboard
Deutsch
43
2. BIOS-Information
Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie <F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelan­gen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch durchführen, indem Sie das System kurz ab- und danach wieder anschalten. Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der Support CD.
3. Software Support CD information
Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebssy­stemen: 7 / 7 64-Bit / Vista beigefügte Support-CD enthält hilfreiche Software, Treiber und Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben. Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen. Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menüges­teuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und die Programme werden dann automatisch installiert.
TM
/ Vista
TM
64-Bit / XP / XP 64-Bit. Die Ihrem Motherboard
Deutsch
44
ASRock Z68M/USB3 Motherboard
1. Introduction
Merci pour votre achat d’une carte mère ASRock Z68M/USB3, une carte mère très able produite selon les critères de qualité rigoureux de ASRock. Elle offre des per­formances excellentes et une conception robuste conformément à l’engagement d’ASRock sur la qualité et la fi abilité au long terme. Ce Guide d’installation rapide présente la carte mère et constitue un guide d’installation pas à pas. Des informations plus détaillées concernant la carte mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD d’assistance.
Les spécifi cations de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notifi cation. Au cas où n’importe qu’elle modifi cation intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis. Vous trouverez les listes de prise en charge des cartes VGA et CPU également sur le site Web ASRock. Site web ASRock, http://www.asrock.com Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez. www.asrock.com/support/index.asp
1.1 Contenu du paquet
Carte mère ASRock Z68M/USB3 (Facteur de forme Micro ATX: 9.6 pouces x 8.6 pouces, 24.4 cm x 21.8 cm) Guide d’installation rapide ASRock Z68M/USB3 CD de soutien ASRock Z68M/USB3 Deux câbles de données de série ATA (SATA) (en option) Un I/O Panel Shield
ASRock vous rappelle...
Pour bénéfi cier des meilleures performances sous Windows® 7 / 7 64 bits
TM
/ Vista
/ VistaTM 64 bits, il est recommandé de paramétrer l'option BIOS dans Confi guration de stockage en mode AHCI. Pour plus de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur votre CD de sup­port.
ASRock Z68M/USB3 Motherboard
Français
45
Français
1.2 Spécifications
Format - Facteur de forme Micro ATX:
9.6 pouces x 8.6 pouces, 24.4 cm x 21.8 cm
- Accessoires de Carte mère CPU - Prend en charge les processeurs Intel deuxième génération dans l’ensemble LGA1155
- Conception 4 + 2 Power Phase
- Prend en charge la technologie Intel® Turbo Boost 2.0
- Prise en charge des unités centrales non verrouillées de série K
- Prise en charge de la technologie Hyper-Threading (voir ATTENTION 1) Chipsets - Intel
®
Z68
Mémoire - Compatible avec la Technologie de Mémoire à Canal Double (voir ATTENTION 2)
- 2 x slots DIMM DDR3
- Supporter DDR3 2133(OC)/1866(OC)/1600/1333/1066 non-ECC, sans amortissement mémoire
- Capacité maxi de mémoire système: 16GB (voir ATTENTION 3)
- Prend en charge le profi l de mémoire extrême Intel Slot d’extension - 1 x slot1 PCI Express 2.0 x16 (bleu @ mode x16)
- 2 x slots PCI Express 2.0 x1
- 1 x slot PCI VGA sur carte - Supporte Intel Sync Video, Intel
®
HD Graphics Built-in Visuals: Intel® Quick
®
InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- mémoire partagée max 1759MB (voir ATTENTION 4)
- Trois options de sortie VGA: D-Sub, DVI-D et HDMI (voir ATTENTION 5)
- Prend en charge le HDMI 1.4a avec une résolution maximale jusqu’à 1920x1200 @ 60Hz
- Prend en charge le DVI avec une résolution maximale jusqu’à 1920x1200 @ 60Hz
- Prend en charge le D-Sub avec une résolution maximale jusqu’à 2048x1536 @ 75Hz
- Prend en charge Lip Sync, xvYCC et HBR (High Bit Rate Audio: Audio à haut débit binaire) avec HDMI (Moniteur compatible HDMI requis) (voir ATTENTION 6)
46
ASRock Z68M/USB3 Motherboard
®
CoreTM i7 / i5 / i3 de
®
(XMP)
- Prise en charge de la fonction HDCP avec ports DVI et HDMI
- Supporter 1080p Blu-ray(BD)/ lecteur de HD-DVD avec ports DVI et HDMI Audio - 7,1 CH HD Audio avec protection de contenu (Realtek ALC892 Audio Codec)
- Prise en charge de l’audio Premium Blu-ray
- Prend en charge THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Support du Wake-On-LAN
- Prise en charge de la détection de câble LAN
- Prend en charge la norme Energy Effi cient Ethernet (Ethernet à effi cacité énergétique) 802.3az
- Supporte PXE
Panneau arrière I/O Panel
- 1 x port clavier PS/2
- 1 x port D-Sub
- 1 x port DVI-D
- 1 x port HDMI
- 1 x Port de sortie optique SPDIF
- 4 x ports USB 2.0 par défaut
- 2 x ports USB 3.0 par défaut
- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et LED VITESSE)
- Prise HD Audio: Haut-parleur latéral / Haut-parleur arrière / Central /Basses / Entrée Ligne / Haut-parleur frontal / Microphone (voir ATTENTION 7)
SATA 3 - 2 x connecteurs SATA3 6,0 Gb/s, prennent en charge les fonctions RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage et Intel Smart Response), NCQ, AHCI et « Hot Plug » (Branche ment à chaud) USB 3.0 - 2 x ports USB3.0 à l’arrière par Etron EJ168A, prennent en charge USB 1.0/2.0/3.0 jusqu’à 5 Gb/s Connecteurs - 4 x connecteurs SATA2, prennent en charge un taux de transfert de données pouvant aller jusqu’à 3.0Go/s, supporte RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage et Intel Smart Response), NCQ, AHCI et « Hot Plug » (Branche ment à chaud)
- 2 x connecteurs SATA3, prennent en charge un taux de
transfert de données pouvant aller jusqu’à 6.0Go/s
Français
ASRock Z68M/USB3 Motherboard
47
Français
- 1 x Port Disquette
- 1 x En-tête du module infrarouge
- 1 x Barrette pour module à infrarouges grand public
- 1 x embase de port d’impression
- 1 x En-tête de port COM
- 1 x Connecteur HDMI_SPDIF
- 1 x Connecteur de LED d’alimentation
- Connecteur pour processeur/châssis/ventilateur
- br. 24 connecteur d’alimentation ATX
- br. 8 connecteur d’alimentation 12V ATX
- Connecteur audio panneau avant
- 3 x En-tête USB 2.0 (prendre en charge 6 ports USB 2.0 supplémentaires) BIOS - 64Mb BIOS AMI
- AMI UEFI Legal BIOS avec support GUI
- Support du “Plug and Play”
- Compatible pour événements de réveil ACPI 1.1
- Gestion jumperless
- Support SMBIOS 2.3.1
- IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Tension Multi-ajustement CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (version d’évaluation), CyberLink MediaEspresso 6.5 Trial, Suite logicielle ASRock (CyberLink DVD Suite et Version OEM et d’essai; Suite multimédia ASRock MAGIX - OEM) Caractéristique - Utilitaire ASRock Extreme Tuning (AXTU) unique (voir ATTENTION 8)
- ASRock l’Instant Boot
- ASRock Instant Flash (voir ATTENTION 9)
- Chargeur ASRock APP (voir ATTENTION 10)
- ASRock SmartView (voir ATTENTION 11)
- ASRock XFast USB (voir ATTENTION 12)
- ASRock XFast LAN (voir ATTENTION 13)
- Lucid Virtu (voir ATTENTION 14)
- L’accélérateur hybride:
- Contrôle direct de la fréquence CPU (voir ATTENTION 15)
- ASRock U-COP (voir ATTENTION 16)
- Garde d’échec au démarrage (B.F.G.)
- Combo Cooler Option (C.C.O.) (voir ATTENTION 17)
- DEL veilleuse
48
ASRock Z68M/USB3 Motherboard
Surveillance - Contrôle de la température CPU
système - Mesure de température de la carte mère
- Tachéomètre ventilateur processeur/châssis/ventilateur
- Ventilateur silencieux pour unité centrale/châssis (permet le
réglage automatique de la vitesse du ventilateur pour châs­sis, selon la température de l’unité centrale)
- Commande de ventilateur CPU à plusieurs vitesses
- Monitoring de la tension: +12V, +5V, +3.3V, Vcore
OS - Microsoft
®
Windows® 7 / 7 64-bit / VistaTM / Vista
TM
64-bit
/ XP / XP 64-bit Certi cations - FCC, CE, WHQL
- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)
(voir ATTENTION 18)
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web: http://www.asrock.com
ATTENTION
Il est important que vous réalisiez qu’il y a un certain risque à effectuer l’overclocking, y compris ajuster les réglages du BIOS, appliquer la technologie Untied Overclocking, ou utiliser des outils de tiers pour l’overclocking. L’overclocking peut affecter la stabilité de votre système, ou même causer des dommages aux composants et dispositifs de votre système. Si vous le faites, c’est à vos frais et vos propres risques. Nous ne sommes pas responsables des dommages possibles causés par l’overclocking.
ATTENTION!
1. En ce qui concerne le paramétrage “Hyper-Threading Technology”, veuillez consulter la page 48 du manuel de l’utilisateur sur le CD tech­nique.
2. Cette carte mère supporte la Technologie de Mémoire à Canal Double. Avant d’intégrer la Technologie de Mémoire à Canal Double, assurez­vous de bien lire le guide d’installation des modules mémoire en page 15 pour réaliser une installation correcte.
3. Du fait des limites du système d’exploitation, la taille mémoire réelle réservée au système pourra être inférieure à 4 Go sous Windows VistaTM / XP. Avec Windows® OS avec CPU 64 bits, il n’y a pas ce genre de limitation.
4. La dimension maximum du memoire partage est defi nie par le vendeur de jeu de puces et est sujet de changer. Veuillez verifi er la Intel pour les informations recentes SVP.
5. Vous pouvez choisir de n’utiliser que deux moniteurs sur trois. Les moniteurs D-Sub, DVI-D et HDMI ne peuvent pas être activés en même temps. En outre, avec l’adaptateur DVI-HDMI, le port DVI-D peut prendre en charge les mêmes fonctions que le port HDMI.
®
7 /
®
website
ASRock Z68M/USB3 Motherboard
Français
49
Français
6. xvYCC et Deep Color ne sont pris en charge que sous Windows® 7 64-
bit / 7. Le mode Deep Color ne sera activé que si le moniteur prend en charge 12bpc en EDID. HBR est pris en charge sous Windows® 7 64-bit / 7 / VistaTM 64-bit / VistaTM.
7. Pour l’entrée microphone, cette carte mère supporte les deux modes stéréo et mono. Pour la sortie audio, cette carte mère supporte les modes 2-canaux, 4-canaux, 6-canaux et 8-canaux. Veuillez vous référer au tableau en page 3 pour effectuer la bonne connexion.
8. ASRock Extreme Tuning Utility (AXTU) est un utilitaire tout-en-un qui permet de régler précisément différentes fonctions du système, via une interface facile à utiliser, incluant Moniteur de périphériques, Contrôle du ventilateur, Overclocking, OC DNA et IES. Dans Moniteur de périphériques, il affi che les valeurs principales de votre système. Dans Contrôle du ventilateur, il affi che la vitesse du ventilateur et la température, que vous pouvez ajuster. Dans Overclocking, vous pouvez overclocker la fréquence du CPU pour améliorer les performances du système. Dans OC DNA, vous pouvez enregistrer vos réglages OC dans un profi l et les partager avec vos amis. Vos amis pourront alors installer
le profi l OC sur leur système pour utiliser les mêmes réglages OC.
Dans IES (Intelligent Energy Saver – Fonction intelligente d’économie d’énergie), le contrôleur de la tension peut réduire le nombre de phases de sortie pour améliorer le fonctionnement lorsque les cores du CPU ne sont pas utilisées, sans diminuer les performances de l’ordinateur. Veuillez visiter notre site Web pour plus d’informations sur l’utilisation des fonctions de l’utilitaire ASRock Extreme Tuning Utility (AXTU).
Site Web de ASRock : http://www.asrock.com
9. O ASRock Instant Flash é um utilitário de fl ash do BIOS incorporado na memória Flash ROM. Esta prática ferramenta de actualização do BIOS permite-lhe actualizar o BIOS do sistema sem necessitar de entrar nos sistemas operativos, como o MS-DOS ou o Windows®. Com este
utilitário, poderá premir a tecla <F6> durante o teste de arranque POST
ou premir a tecla <F2> para exibir o menu de confi guração do BIOS para aceder ao ASRock Instant Flash. Execute esta ferramenta para guardar o novo fi cheiro de BIOS numa unidade fl ash USB, numa disquete ou num disco rígido, em seguida, poderá actualizar o BIOS com
apenas alguns cliques sem ter de utilizar outra disquete ou outro compli-
cado utilitário de fl ash. Note que a unidade fl ash USB ou a unidade de disco rígido devem utilizar o sistema de fi cheiros FAT32/16/12.
10. Si vous désirez un moyen plus rapide et moins contraignant de recharger vos appareils Apple tels que iPhone/iPod/iPad Touch, ASRock a préparé pour vous la solution idéale - le chargeur ASRock APP. Il suffi t d’installer le pilote du chargeur APP, et vous pourrez recharger rapidement votre iPhone à partir de votre ordinateur, jusqu’à 40% plus vite qu’avant. Le chargeur ASRock APP vous permet de charger rapidement et simultané­ment plusieurs appareils Apple, et le chargement continu est même
pris en charge lorsque le PC passe en mode Veille (S1), Suspension à la
RAM (S3), hibernation (S4) ou hors tension (S5). Lorsque le pilote du
50
ASRock Z68M/USB3 Motherboard
chargeur APP est installé, vous découvrez un mode de mise en charge tout à fait inédit. Site web ASRock : http://www.asrock.com/Feature/AppCharger/index.asp
11.
SmartView, une nouvelle fonction du navigateur Internet, est une page de démarrage intelligente de IE, comportant à la fois vos sites Internet les plus visités, votre historique, vos amis Facebook et l’actualité en temps réel, le tout sur une vue optimisée pour une expérience de l’Internet encore plus personnelle. Les cartes mères ASRock sont équipées en ex­clusivité de l’utilitaire SmartView, ce qui vous permet de garder le contact avec vos amis itinérants. Pour utiliser la fonction SmartView, veuillez vous assurez que votre version de système d’exploitation est Windows 7 / 7 64 bits / VistaTM / VistaTM 64 bits, et que vous utilisez le navigateur IE8. Site Internet ASRock : http://www.asrock.com/Feature/SmartView/
index.asp
12. ASRock XFast USB permet d’améliorer les performances de votre péri­phérique de stockage USB. Les performances réelles dépendent des propriétés du périphérique.
13. ASRock XFast LAN fournit un accès Internet plus rapide, avec les avan­tages suivants. Priorisation d’application LAN : Vous pouvez confi gurer votre priorité d’application idéalement et/ou ajouter des nouveaux pro­grammes. Latence plus basse dans les jeux : Après avoir réglé la priorité de jeux en ligne plus haute, cela peut réduire la latence dans les jeux. Forme du trafi c : Vous pouvez regarder des vidéos HD YouTube et té- lécharger simultanément des fi chiers. Analyse en temps réel de vos don- nées : Avec la fenêtre d’état, vous pouvez facilement reconnaître les fl ux de données que vous êtes en train de transférer.
14. Avec la technologie Lucid Virtu, vous pouvez regarder les performances 3D du GPU discret et les fonctions multimédia avancées des graphiques
®
Intel
HD.
15. Même si cette carte mère offre un contrôle sans souci, il n’est pas re­commandé d’y appliquer un over clocking. Des fréquences de bus CPU autres que celles recommandées risquent de rendre le système instable ou d’endommager le CPU et la carte mère.
16. Lorsqu’une surchauffe du CPU est détectée, le système s’arrête automatiquement. Avant de redémarrer le système, veuillez vérifi er que le ventilateur d’UC sur la carte mère fonctionne correctement et débran­chez le cordon d’alimentation, puis rebranchez-le. Pour améliorer la dis­sipation de la chaleur, n’oubliez pas de mettre de la pâte thermique entre le CPU le dissipateur lors de l’installation du PC.
17. Le Combo Cooler Option (C.C.O.) offre un choix fl exible pour adopter trois types différents de refroidisseur sde CPU, les sockets LGA 775, LGA 1155 et LGA 1156. Veuillez noter que tous les ventilateurs de CPU 775 et 1156 ne peuvent pas être utilisés.
18. EuP, qui signifi e Energy Using Product (Produit Utilisant de l’Energie), est une disposition établie par l’Union Européenne pour défi nir la con- sommation de courant pour le système entier. Conformément à la norme EuP, le courant CA total du système entier doit être inférieur à 1 W en
®
Français
ASRock Z68M/USB3 Motherboard
51
Français
mode d’arrêt. Pour être conforme à la norme EuP, une carte mère EuP
et une alimentation EuP sont requises. Selon les suggestions d’Intel’, l’alimentation électrique EuP doit correspondre à la norme, qui est que l’effi cacité électrique de 5v en mode de veille doit être supérieure à 50% pour 100 mA de consommation de courant. Pour choisir une alimentation électrique conforme à la norme EuP, nous vous recommandons de con­sulter votre fournisseur de courant pour plus de détails.
1.3 Réglage des cavaliers
L’illustration explique le réglage des cava­liers. Quand un capuchon est placé sur les broches, le cavalier est « FERME ». Si au­cun capuchon ne relie les broches,le cava­lier est « OUVERT ». L’illustration montre un cavalier à 3 broches dont les broches 1 et 2 sont « FERMEES » quand le capuchon est placé sur ces 2 broches.
Le cavalier Description
Effacer la CMOS
(CLRCMOS1) (voir p.2 fi g. 9)
Remarque :
Paramètres par défaut
CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer et réinitialiser les paramètres du système à la confi guration originale, veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de la prise de courant. Après 15 secondes, utilisez un couvercle de jumper pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant secondes. Veuillez cependant ne pas effacer le CMOS immédiatement a
près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS après avoir mis à jour le BIOS, vous devez allumer en premier le système, puis l’éteindre avant de continuer avec l’opération d’effacement du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le profi l par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés seulement si la batterie du CMOS est enlevée.
Effacer la CMOS
5
52
ASRock Z68M/USB3 Motherboard
1.4 En-têtes et Connecteurs sur Carte
Connecteur du lecteur de disquette
(FLOPPY1 br. 33) (voir p.2 No. 25)
Note: Assurez-vous que le côté avec fi l rouge du câble est bien branché sur le côté Broche1 du connecteur.
Connecteurs Série ATAII Ces quatre connecteurs Série
(SATA2_2: voir p.2 No. 13)
(SATA2_3: voir p.2 No. 12)
(SATA2_4: voir p.2 No. 14)
(SATA2_5: voir p.2 No. 15)
actuelle permet des taux transferts de données pouvant
aller jusqu’à 3,0 Gb/s.
Connecteurs Série ATA3 Ces deux connecteurs Série
(SATA3_0: voir p.2 No. 7)
(SATA3_1: voir p.2 No. 8)
les périphériques de stockage internes. L’interface SATA3 actuelle permet des taux transferts de données pouvant
aller jusqu’à 6,0 Gb/s.
Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers. NE PAS placer les capuchons de cavalier sur ces en-têtes et con­necteurs. Le fait de placer les capuchons de cavalier sur les en-têtes et connecteurs causera à la carte mère des dommages irréversibles!
le côté avec fi l rouge côté Broche1
ATAII (SATAII) prennent en
SATA2_3 SATA2_2
charge les câbles SATA pour les périphériques de stockage internes. L’interface SATAII
SATA2_5 SATA2_4
ATA3 (SATA3) prennent en
charge les câbles SATA pour
SATA3_0
SATA3_1
Câble de données Toute cote du cable de data Série ATA (SATA) SATA peut etre connecte au
(en option)
disque dur SATA / SATAII / SATA3 ou au connecteur SATAII / SATA3 sur la carte mere.
Français
53
ASRock Z68M/USB3 Motherboard
1
1
1
USB_PWR
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
USB_PWR
P-13
P-12
P+12
1
P+9
P+8
P+11
P+10
P+13
IRTX
IRRX
GND
GND
GND
GND
GND
GND
+5VSB
DUMMY
DUMMY
DUMMY
DUMMY
GND
En-tête USB 2.0 A côté des quatre ports
(USB6_7 br.9)
(voir p.2 No. 22)
USB 2.0 par défaut sur le
panneau E/S, il y a trois embases USB 2.0 sur cette carte mère. Chaque embase USB 2.0 peut prendre en
(USB8_9 br.9)
(voir p.2 No. 20)
(USB10_11 br.9) (voir p.2 No. 19)
charge 2 ports USB 2.0.
En-tête du module infrarouge Cet en-tête supporte un module
(IR1 br.5)
infrarouge optionnel de
(voir p.2 No. 6)
transfert et de réception sans
fi l.
Barrette pour module à infrarouges grand public Cette barrette peut être utilisée
(CIR1 br.4)
(voir p.2 No. 23)
comme chaînes hi-fi ,
pour connecter des modules
à infrarouges grand public,
1
ATX+5VSB
IRRX
IRTX
GND
décodeurs, etc.
Français
Embase de port d’impression AIl s’agit d’une interface pour le
(LPT1 25 broches)
(voir p.2 No. 24)
permet le raccordement pratique de périphériques d’impression.
Connecteur audio panneau C’est une interface pour
(HD_AUDIO1 br. 9)
(voir p.2 No. 27)
qui permet le branchement et le contrôle commodes de périphériques audio.
AFD#
câble du port d’impression, qui
un câble avant audio en façade
1
STB#
ERROR#
PINIT#
SPD1
SPD0
SLIN#
SPD2
SPD3
SPD4
1
SPD5
GND
MIC2_L
GND
SPD7
SPD6
ACK#
PRESENCE#
MIC_RET
OUT2_R
MIC2_R
BUSY
OUT_RET
OUT2_L
J_SENSE
PE
SLCT
54
ASRock Z68M/USB3 Motherboard
1. L’audio à haute défi nition (HDA) prend en charge la détection de fi che, mais le fi l de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de châssis afi n installer votre système.
2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio du panneau avant conformément à la procédure ci-dessous : A. Connectez Mic_IN (MIC) à MIC2_L. B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L. C. Connectez Ground (GND) à Ground (GND). D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous n’avez pas besoin de les connecter pour le panneau audio AC’97. E. Pour activer le micro avant. Pour les systèmes d’exploitation Windows Sélectionnez “Mixer”. Sélectionnez “Recorder” (Enregistreur). Puis cliquez sur “FrontMic” (Micro avant). Pour les systèmes d’exploitation Windows VistaTM 64 bits : Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).
®
XP / XP 64 bits :
®
7 / 7 64 bits / VistaTM /
En-tête du panneau système Cet en-tête permet d’utiliser
(PANEL1 br.9)
(voir p.2 No. 18)
Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et l’indicateur d’état du système du châssis sur cette barrette en respectant l’affectation des broches décrite ci-dessous. Faites attention aux broches positives et négatives avant de connecter les câbles.
plusieurs fonctions du
panneau système frontal.
PWRBTN (Interrupteur d’alimentation):
Connectez ici le connecteur d’alimentation sur le panneau avant du châssis. Vous pouvez confi gurer la façon de mettre votre système hors tension avec l’interrupteur d’alimentation.
RESET (Interrupteur de réinitialisation):
Connectez ici le connecteur de réinitialisation sur le panneau avant du châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.
PLED (DEL alimentation système):
Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le système est en marche. Le voyant DEL clignote lorsque le système est en mode veille S1. Le voyant DEL est éteint lorsque le système est en mode veille S3/ S4 ou lorsqu’il est éteint (S5).
ASRock Z68M/USB3 Motherboard
Français
55
HDLED (DEL activité du disque dur):
Connectez ici le voyant DEL d’activité du disque dur sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en train de lire ou d’écrire des données.
Le design du panneau avant peut varier en fonction du châssis. Un module de panneau avant consiste principalement en : interrupteur d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation, voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous connectez le panneau avant de votre châssis sur cette barrette, vérifi ez bien à faire correspondre les fi ls et les broches.
En-tête du haut-parleur Veuillez connecter le de châssis haut-parleur de châssis sur
(SPEAKER1 br. 4)
(voir p.2 No. 21)
cet en-tête.
Français
LED di accensione Collegare il LED di accensione
(3-pin PLED1)
(vedi p.2 Nr. 16)
chassi per indicare lo stato di
alimentazione del sistema. Il
1
PLED+
PLED+
PLED-
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
Connecteur pour châssis et ventilateur
(CHA_FAN1 br. 3)
(voir p.2 No. 17)
GND +12V CHA_FAN_SPEED
Branchez les câbles du ventilateur aux connecteurs pour ventilateur et faites correspondre le fi l noir à la broche de terre.
(PWR_FAN1 br. 3)
(voir p.2 No. 33)
Connecteur du ventilateur Veuillez connecter le câble de de l’UC ventilateur d’UC sur ce
(CPU_FAN1 br. 4)
(voir p.2 No. 1)
connecteur et brancher le fi l
noir sur la broche de terre.
PWR_FAN_SPEED
+12V
GND
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
56
ASRock Z68M/USB3 Motherboard
Bien que cette carte mère offre un support de (Ventilateur silencieux ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut bien fonctionner même sans la fonction de commande de vitesse du ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3 broches au connecteur du ventilateur de CPU sur cette carte mère, veuillez le connecter aux broches 1-3.
Installation de ventilateur à 3 broches
Broches 1-3 connectées
En-tête d’alimentation ATX Veuillez connecter l’unité
(ATXPWR1 br. 24)
(voir p.2 No. 5)
Bien que cette carte mère fournisse un connecteur de courant ATX 24 broches, elle peut encore fonctionner
d’alimentation ATX sur cet en-
tête.
12 124
13
12
24
si vous adopter une alimentation traditionnelle ATX 20 broches. Pour utiliser une alimentation ATX 20 broches, branchez à l’alimentation électrique ainsi qu’aux broches 1 et 13.
20-Installation de l’alimentation électrique ATX
Connecteur ATX 12V Veuillez connecter une unité
(ATX12V1 br.8)
(voir p.2 No. 2)
d’alimentation électrique ATX 12V sur ce connecteur.
8 5
4 1
1
13
Bien que cette carte mère possède 8 broches connecteur d’alimentation ATX 12V, il peut toujours travailler si vous adoptez une approche traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser l’alimentation des 4 broches ATX, branchez votre alimentation avec la broche 1 et
8 5
la broche 5.
4-Installation d’alimentation à 4 broches ATX 12V
4 1
En-tête de port COM Cette en-tête de port COM est
(COM1 br.9)
(voir p.2 No. 26)
utilisée pour prendre en charge
un module de port COM.
ASRock Z68M/USB3 Motherboard
Français
57
Connecteur HDMI_SPDIF Connecteur HDMI_SPDIF,
(HDMI_SPDIF1 2-pin)
(voir p.2 No. 28)
SPDIF vers la carte VGA HDMI,
fournissant une sortie audio
1
SPDIFOUT
GND
et permettant au système de se connecter au un téléviseur numérique HDMI /un projecteur / un périphérique LCD. Veuillez brancher le connecteur HDMI_SPDIF de la carte VGA HDMI sur ce connecteur.
Français
58
ASRock Z68M/USB3 Motherboard
2. Informations sur le BIOS
La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-On­Self-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier du système. Vous pouvez également redémarrer en éteignant le système et en le rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un programme piloté par menu, qui vous permet de faire défi ler par ses divers sous- menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées sur le BIOS, veuillez consulter le Guide de l’utilisateur (fi chier PDF) dans le CD technique.
3. Informations sur le CD de support
Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®: 7 / 7 64 bits / VistaTM / Vista cette carte mère contient les pilotes et les utilitaires nécessaires pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu principal s’affi che automatiquement si “AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas automatiquement, locali­sez dans le CD technique le fi chier “ASSETUP.EXE” dans le dossier BIN et double- cliquez dessus pour affi cher les menus.
TM
64 bits / XP / XP 64 bits. Le CD technique livré avec
ASRock Z68M/USB3 Motherboard
Français
59
1. Introduzione
Grazie per aver scelto una scheda madre ASRock Z68M/USB3, una scheda madre affi dabile prodotta secondo i severi criteri di qualità ASRock. Le prestazioni eccel- lenti e il design robusto si conformano all’impegno di ASRock nella ricerca della qualità e della resistenza. Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si possono trovare nel manuale per l’utente presente nel CD di supporto.
Le specifi che della scheda madre e il software del BIOS possono essere aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia modifi cato, la versione aggiornata sarà disponibile sul sito di ASRock senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate. ASRock website http://www.asrock.com Se si necessita dell’assistenza tecnica per questa scheda madre, visitare il nostro sito per informazioni specifi che sul modello che si sta usando. www.asrock.com/support/index.asp
1.1 Contenuto della confezione
Scheda madre ASRock Z68M/USB3 (Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm) Guida di installazione rapida ASRock Z68M/USB3 CD di supporto ASRock Z68M/USB3 Due cavi dati Serial ATA (SATA) (opzionali) Un I/O Shield
Italiano
60
ASRock vi ricorda...
Per ottenere migliori prestazioni in Windows® 7 / 7 64-bit / Vista 64-bit, si consiglia di impostare l'opzione BIOS in Storage Confi guration (Confi gurazione di archiviazione) sulla modalità AHCI. Per l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'utente) nel CD di supporto per dettagli.
TM
/ VistaTM
ASRock Z68M/USB3 Motherboard
1.2 Specifiche
Piattaforma - Micro ATX Form Factor: 9.6-in x 8.6-in, 24.4 cm x 21.8 cm
- Design condensatore compatto Processore - Supporta Intel pacchetto in LGA1155
- Struttura di fase con alimentazione 4 + 2
- Supporto della tecnologia Intel
- Supporta CPU unlocked serie K
- Supporto tecnologia Hyper Threading (vedi ATTENZIONE 1) Chipset - Intel
®
Z68
Memoria - Supporto tecnologia Dual Channel Memory (vedi ATTENZIONE 2)
- 2 x slot DDR3 DIMM
- Supporto DDR3 2133(OC)/1866(OC)/1600/1333/1066 non-ECC, momoria senza buffer
- Capacità massima della memoria di sistema: 16GB (vedi ATTENZIONE 3)
- Supporto di Intel Slot di - 1 x Alloggi PCI Express 2.0 x16 (blu a modalità x16) espansione - 2 x Alloggio PCI Express 2.0 x1
- 1 x Alloggi PCI VGA su scheda - Supporta Intel Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- Memoria massima condivisa 1759MB (vedi ATTENZIONE 4)
- Tre opzioni d’output VGA: D-Sub, DVI-D e HDMI (vedi ATTENZIONE 5)
- Supporta HDMI 1.4a con risoluzione massima fi no a 1920x1200 @ 60Hz
- Supporta DVI con risoluzione massima fi no a 1920x1200 @ 60Hz
- Supporta D-Sub con risoluzione massima fi no a 2048x1536 @ 75Hz
- Supporto delle funzioni Auto Lip Sync, xvYCC e HBR (High Bit Rate Audio) con HDMI (è necessario un monitor compatibile HDMI) (vedi ATTENZIONE 6)
- Supporto della funzione HDCP con le porte DVI e HDMI
- Supporto 1080p Blu-ray (BD) / HD-DVD riproduzione con le porte DVI e HDMI
ASRock Z68M/USB3 Motherboard
®
CoreTM i7 / i5 / i3 di seconda generazione in
®
Turbo Boost 2.0
®
XMP (Extreme Memory Profi le)
®
HD Graphics Built-in Visuals: Intel® Quick Sync
Italiano
61
Italiano
Audio - 7.1 CH HD Audio con protezioni contenuti (Realtek ALC892 Audio Codec)
- Supporto audio Blu-ray Premium
- Supporto THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supporta Wake-On-LAN
- Supporta il rilevamento cavo LAN
- Supporto di Energy Effi cient Ethernet 802.3az
- Supporta PXE Pannello I/O Panel posteriore I/O - 1 x porta PS/2 per tastiera
- 1 x Porta D-Sub
- 1 x Porta DVI-D
- 1 x Porta HDMI
- 1 x Porta ottica SPDIF Out
- 4 x porte USB 2.0 già integrate
- 2 x porte USB 3.0 già integrate
- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e LED velocità)
- Connettore HD Audio: cassa posteriore / cassa centrale / bassi / ingresso linea / cassa frontale / microfono (vedi ATTENZIONE 7) SATA 3 - 2 x Connettori SATA3 6,0Gb/s, supporto RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage e tecnologia Intel Smart Response) e delle funzioni NCQ, AHCI e “Hot Plug” USB 3.0 - 2 x porte USB 3.0 posteriori amministrate dal controller Etron EJ168A, supporto di USB 1.0/2.0/3.0 fi no a 5Gb/s Connettori - 4 x connettori SATA2 3.0Go/s, sopporta RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage e tecnologia Intel Smart Response) e delle funzioni NCQ, AHCI e “Hot Plug”
- 2 x connettori SATA3 6.0Go/s
- 1 x porta Floppy
- 1 x Collettore modulo infrarossi
- 1 x
Connettore modulo infrarosso consumer
- 1 x Collettore porta stampante
- 1 x collettore porta COM
- 1 x connettore HDMI_SPDIF
- 1 x LED di accensione
- Connettore CPU/Chassis/Alimentazione ventola
- 24-pin collettore alimentazione ATX
- 8-pin connettore ATX 12V
62
ASRock Z68M/USB3 Motherboard
- Connettore audio sul pannello frontale
- 3 x Collettore USB 2.0 (supporta 6 porte USB 2.0)
BIOS - 64Mb AMI BIOS
- AMI UEFI Legal BIOS con interfaccia di supporto
- Supporta “Plug and Play”
- Compatibile con ACPI 1.1 wake up events
- Supporta jumperfree
- Supporta SMBIOS 2.3.1
- Regolazione multi-voltaggio IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA
CD di - Driver, Utilità, Software AntiVirus (versione di prova), supporto CyberLink MediaEspresso 6.5 Trial, Suite software ASRock
(Suite CyberLink DVD OEM e Versione demo; Suite multimediale ASRock MAGIX - OEM) Caratteristica - ASRock Extreme Tuning Utility (AXTU) (vedi ATTENZIONE 8) speciale - ASRock Instant Boot
- ASRock Instant Flash (vedi ATTENZIONE 9)
- Caricatore ASRock APP Charger (vedi ATTENZIONE 10)
- ASrock SmartView (vedi ATTENZIONE 11)
- ASRock XFast USB (vedi ATTENZIONE 12)
- ASRock XFast LAN (vedi ATTENZIONE 13)
- Lucid Virtu (vedi ATTENZIONE 14)
- Booster ibrido:
- Stepless control per frequenza del processore (vedi ATTENZIONE 15)
- ASRock U-COP (vedi ATTENZIONE 16)
- Boot Failure Guard (B.F.G.)
- Opzione C.C.O. (Combo Cooler Option) (vedi ATTENZIONE 17)
- LED notturno Monitoraggio - Sensore per la temperatura del processore Hardware - Sensore temperatura scheda madre
- Indicatore di velocità per la ventola del CPU/Chassis/ Alimentazione
- Ventola CPU/Chassis silenziosa (permette la regolazione automatica della ventola dello chassis in base alla temperatura della CPU)
- Ventola CPU con controllo di varie velocità
- Voltaggio: +12V, +5V, +3.3V, Vcore Compatibi- - Microsoft
®
Windows® 7 / 7 64 bit / VistaTM / Vista
TM
64 bit / XP /
lità SO XP 64 bit Certifi cazioni - FCC, CE, WHQL
ASRock Z68M/USB3 Motherboard
Italiano
63
- Predisposto ErP/EuP (è necessaria l’alimentazione predisposta per il sistema ErP/EuP) (vedi ATTENZIONE 18)
* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com
AVVISO
Si prega di prendere atto che la procedura di overclocking implica dei rischi, come anche la regolazione delle impostazioni del BIOS, l’applicazione della tecnologia Untied Overclocking Technology, oppure l’uso di strumenti di overclocking forniti da terzi. L’overclocking può infl uenzare la stabilità del sistema, ed anche provocare danni ai componenti ed alle periferiche del sistema. La procedura è eseguita a pro prio rischio ed a proprie spese. Noi non possiamo essere ritenuti responsabili per possibili danni provocati dall’overclocking.
Italiano
ATTENZIONE!
1. Per il settaggio della “Tecnologia Hyper-Threading”, per favore controllare pagina 48 del Manuale dell’utente all’interno del CD di supporto.
2. Questa scheda madre supporta la tecnologia Dual Channel Memory. Prima di implementare la tecnologia Dual Channel Memory, assicurarsi di leggere la guida all’installazione dei moduli di memoria, a pagina 15, per seguire un’installazione appropriata.
3. A causa delle limitazioni del sistema operativo, le dimensioni effettive della memoria possono essere inferiori a 4GB per l’accantonamento riservato all’uso del sistema sotto Windows CPU 64-bit, non c’è tale limitazione.
4. La dimensione massima della memoria condivisa viene stabilita dal ven­ditore del chipset ed e‘ soggetta a modifi cazioni. Prego fare riferimento al sito internet Intel
5. Si può solo scegliere di usare due dei tre monitor. I monitor D-Sub, DVI­D e HDMI non possono essere abilitati contemporaneamente. Inoltre, usando l’adattatore DVI a HDMI la porta DVI-D può supportare le stesse funzioni della porta HDMI.
6. Le funzioni xvYCC e Deep Color sono supportate solo sotto Windows 7 64-bit / 7. La modalità Deep Color sarà abilitata solo se lo schermo supporta la funzione 12bpc in EDID. La funzione HBR è supportata sotto
®
Windows
7. Questa scheda madre supporta l’ingresso stereo e mono per il microfono. Questa scheda madre supporta le modalità 2 canali, 4 canali, 6 canali e 8 canali per l’uscita audio. Controllare la tavola a pagina 3 per eseguire il collegamento appropriato.
8.
L’utilità AXTU (ASRock Extreme Tuning Utility) è uno strumento tutto in uno per regolare varie funzioni del sistema in un’interfaccia facile da usare che include monitoraggio hardware, controllo ventola, overclocking, OC DNA ed IES. Hardware Monitor (Monitoraggio hardware) mostra le letture principali del sistema. Fan Control (Controllo ventola) mostra la velocità e la temperatura che possono essere regolate. Overclocking permette di eseguire l’overclocking della frequenza della CPU per
7 64-bit / 7 / VistaTM 64-bit / VistaTM.
®
7 / VistaTM / XP. Per Windows® OS con
®
per le ultime informazioni.
®
64
ASRock Z68M/USB3 Motherboard
ottenere le prestazioni ottimali del sistema. OC DNA permette di salvare
le impostazioni OC come un profi lo da condividere con gli amici! Gli amici
possono scaricare il profi lo OC sul loro sistema operativo per ottenere le stesse impostazioni OC Il regolatore di tensione di IES (Intelligent Energy
Saver) può ridurre il numero di fasi d’uscita per migliorare l’effi cienza
quando i core CPU sono inattivi senza sacrifi care le prestazioni di computazione. Vistare il nostro per informazioni sulle procedure operative dell’utilità AXTU (ASRock Extreme Tuning Utility).
Sito ASRock: http://www.asrock.com
9. ASRock Instant Flash è una utilità Flash BIOS integrata nella Flash ROM. Questo comodo strumento d’aggiornamento del BIOS permette di aggior­nare il sistema BIOS senza accedere a sistemi operativi come MS-DOS or Windows POST, oppure il tasto <F2> nel menu BIOS per accedere ad ASRock In­stant Flash. Avviare questo strumento e salvare il nuovo fi le BIOS nell’unità Flash USB, dischetto (disco fl oppy) o disco rigido; poi si può aggiornare il BIOS con pochi clic, senza preparare altri dischetti (dischi fl oppy) o altre complicate utilità Flash. Si prega di notare che l’unità Flash USB o il disco rigido devono usare il File System FAT32/16/12.
10. Se vuoi un modo rapido e indipendente per caricare i dispositivi Apple, come iPhone/iPod/iPad Touch, ASRock ha preparato una soluzione meravigliosa: ASRock APP Charger. Basta installare il driver APP Char­ger per caricare l’iPhone più rapidamente rispetto al computer, con una velocità maggiore del 40%. ASRock APP Charger permette di caricare simultaneamente molti dispositivi Apple in modo rapido e supporta anche il caricamento continuato quando il PC accede alla modalità di Standby (S1), Sospensione su RAM (S3), Ibernazione (S4) o Spegnimento (S5). Una volta installato il driver APP Charger si otterranno prodigi e comodità mai avuti prima.
Sito ASRock: http://www.asrock.com/Feature/AppCharger/index.asp
11.
SmartView, una nuova funzione di browser Internet, è la pagina iniziale intelligente di IE che unisce i siti web più visitati, la cronologia, gli amici di Facebook e il newsfeed in tempo reale in una visione migliorata per una esperienza Internet più personale. Le schede madri ASRock sono dotate in modo esclusivo dell’utility SmartView, che consente di mantenersi sempre in contatto con gli amici. Per utilizzare la funzione SmartView, as­sicurarsi che la versione del sistema operativo sia Windows / VistaTM / VistaTM 64 bit e che la versione del browser sia IE8. Sito web
ASRock: http://www.asrock.com/Feature/SmartView/index.asp
12. ASRock XFast USB può accelerare le prestazioni del dispositivo
d’archiviazione USB. Le prestazioni dipendono dalle proprietà del dispositivo.
13. ASRock XFast LAN offre un accesso a Internet più veloce, che compren­de i seguenti benefi ci. Priorità alle applicazioni LAN: è possibile confi gu- rare la priorità assegnata alle applicazioni in modo ideale e/o aggiungere nuovi programmi. Minore latenza nei giochi: dopo avere impostato la priorità dei giochi su un livello più alto, la latenza dei giochi può essere
®
. Con questa utilità, si può premere il tasto <F6> durante il
®
7 / 7 64 bit
Italiano
ASRock Z68M/USB3 Motherboard
65
minore. Confi gurazione del traffi co: è possibile seguire video HD su
Youtube e scaricare fi le contemporaneamente. Analisi in tempo reale dei dati: grazie alla fi nestra di stato, è possibile riconoscere con facilità quali dati si stanno trasferendo in streaming.
14. Grazie alla tecnologia Lucid Virtu, è possibile godere dei benefi ci della
prestazione 3D e del discreto GPU, nonché delle caratteristiche multime­diali avanzate delle grafi che 3D Intel
15. Anche se questa motherboard offre il controllo stepless, non si consiglia
di effettuare l’overclocking. Frequenze del bus del processore diverse da quelle raccomandate possono causare instabilità al sistema o danni al processore e alla scheda madre.
16. Se il processore si surriscalda, il sistema si chiude automaticamente. Pri-
ma di riavviare il sistema, assicurarsi che la ventolina CPU della scheda madre funzioni correttamente; scollegare e ricollegare il cavo d’alimen­tazione. Per migliorare la dissipazione del calore, ricordare di applicare l’apposita pasta siliconica tra il processore e il dissipatore quando si installa il sistema.
17. L’opzione C.C.O. (Combo Cooler Option) fornisce la fl essibilità di impie-
gare tre tipi diversi di dispersori di calore CPU, Socket LGA 775, LGA 1155 e LGA 1156. Notare che non possono essere usate tutte le ventole CPU 775 e 1156.
18. EuP, che sta per Energy Using Product (Prodotto che consuma energia) ,
era una normativa emanata dall’Unione Europea che defi niva il consumo energetico del sistema completo. In base all’EuP, l’alimentazione totale del sistema completo deve essere inferiore a 1,00 W quando è spento. Per soddisfare la norma EuP sono necessari un alimentatore e una scheda elettrica predisposti EuP. In base ai suggerimenti Intel l’alimenta­tore predisposto EuP deve soddisfare lo standard secondo cui l’effi cienza energetica in standby di 5 v è più alta del 50% con un consumo di corren­te di 100 mA. Per la scelta di un’alimentatore predisposto EuP consiglia­mo di verifi care ulteriori dettagli con il produttore.
®
.
Italiano
66
ASRock Z68M/USB3 Motherboard
1.3 Setup dei Jumpers
L’illustrazione mostra come sono settati i jump­er. Quando il ponticello è posizionato sui pin, il jumper è “CORTOCIRCUITATO”. Se sui pin non ci sono ponticelli, il jumper è “APERTO”. L’illustrazione mostra un jumper a 3 pin in cui il pin1 e il pin2 sono “CORTOCIRCUITATI” quan­do il ponticello è posizionato su questi pin.
Jumper Settaggio del Jumper
Resettare la CMOS
(CLRCMOS1) (vedi p.2 item 9)
Nota:
CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare i
parametri del sistema sulla confi gurazione iniziale, spegnere il computer e
Impostazione
predefi nita
scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi, poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. No­tare che password, data, ore, profi lo utente predefi nito, 1394 GUID e indirizzo MAC saranno cancellati solo se è rimossa la batteria della CMOS.
Azzeramen-
to CMOS
ASRock Z68M/USB3 Motherboard
Italiano
67
Italiano
1.4 Collettori e Connettori su Scheda
Connettore del Floppy disk
(33-pin FLOPPY1) (vedi p.2 Nr. 25)
Nota: Assicurarsi che il lato del cavo con la striscia rossa sia inserito nel lato Pin1 del connettore.
Connettori Serial ATAII Questi quattro connettori Serial
(SATA2_2: vedi p.2 Nr. 13)
(SATA2_3: vedi p.2 Nr. 12)
(SATA2_4: vedi p.2 Nr. 14)
(SATA2_5: vedi p.2 Nr. 15)
SATA per dispositivi di memoria interni. L’interfaccia SATAII attuale permette velocità di trasferimento dati fi no a
3.0 Gb/s.
Connettori Serial ATA3 Questi due connettori Serial
(SATA3_0: vedi p.2 Nr. 7)
(SATA3_1: vedi p.2 Nr. 8)
immagazzinamento interni. ATA3 (SATA3) supportano cavi SATA per dispositivi di memoria interni. L’interfaccia SATA3 attuale permette velocità di trasferimento dati fi no a
6.0 Gb/s.
Cavi dati Serial ATA (SATA) Una o altra estremità del cavo
(Opzionale)
collegata al disco rigido SATA / SATAII / SATA3 o al connettore di SATAII / SATA3 su questa cartolina base.
I collettori ed i connettori su scheda NON sono dei jumper. NON instal­lare cappucci per jumper su questi collettori e connettori. L’installazione di cappucci per jumper su questi collettori e connettori provocherà danni permanenti alla scheda madre!
Lato del Pin1 con la striscia rossa
ATAII (SATAII) supportano cavi
SATA2_3 SATA2_2
dati SATA per dispositivi di immagazzinamento interni. ATAII (SATAII) supportano cavi
SATA2_5 SATA2_4
ATA3 (SATA3) supportano cavi dati SATA per dispositivi di
SATA3_0
SATA3_1
di dati SATA può essere
68
ASRock Z68M/USB3 Motherboard
Collettore USB 2.0 Oltre alle quattro porte USB 2.0
(9-pin USB6_7)
(vedi p.2 Nr. 22)
predefi nite nel pannello I/O, la
scheda madre dispone di tre intestazioni USB 2.0. Ciascuna intestazione USB 2.0 supporta due porte USB 2.0.
(9-pin USB8_9) (vedi p.2 Nr. 20)
(9-pin USB10_11) (vedi p.2 Nr. 19)
Collettore modulo infrarossi Questo collettore supporta
(5-pin IR1)
moduli ad infrarossi optional
(vedi p.2 Nr. 6)
per la trasmissione e la
ricezione senza fi li.
1
1
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
IRTX
1
IRRX
P+9
P+8
P+11
P+10
+5VSB
GND
GND
GND
GND
GND
DUMMY
DUMMY
DUMMY
Connettore modulo infrarosso consumer Questo connettore può essere
(4-pin CIR1)
(vedi p.2 Nr. 23)
consumer, come ad esempio
utilizzato per collegare
dispositivi all'infrarosso
1
ATX+5VSB
IRRX
IRTX
GND
apparecchiature HI-FI, TV, ecc.
Collettore porta stampante Questa è un’interfaccia per il
(LPT1 25 pin)
(vedi p.2 No. 24)
cavo porta stampante che
consente di collegare, con comodità, dispositivi di stampa.
Connettore audio sul È un’interfaccia per il cavo del pannello frontale pannello audio. Che consente
(9-pin HD_AUDIO1)
(vedi p.2 Nr. 27)
dei dispositivi audio.
AFD#
ERROR#
PINIT#
SLIN#
1
SPD2
SPD1
SPD0
STB#
connessione facile e controllo
SPD3
1
SPD5
SPD4
GND
PRESENCE#
MIC2_R
MIC2_L
GND
SPD7
SPD6
MIC_RET
J_SENSE
OUT2_R
ACK#
BUSY
OUT_RET
OUT2_L
PE
SLCT
ASRock Z68M/USB3 Motherboard
Italiano
69
1. La caratteristica HDA (High Defi nition Audio) supporta il rilevamento dei connettori, però il pannello dei cavi sul telaio deve supportare la funzione HDA (High Defi nition Audio) per far sì che questa operi in modo corretto. Attenersi alle istruzioni del nostro manuale e del manuale del telaio per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio del pannello anteriore, come indicato di seguito:
A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L. C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97.
E. Per attivare il microfono frontale. Sistema operativo Windows® XP / XP 64-bit: Selezionare “Mixer”. Selezionare “Recorder” (Registratore). Poi, fare clic su “FrontMic” (Microfono frontale). Sistema operativo Windows Andare alla scheda “FrontMic” (Microfono frontale) del pannello di controllo Realtek. Regolare la voce “Recording Volume” (Volume registrazione).
®
7 / 7 64-bit / VistaTM / VistaTM 64-bit:
Collettore pannello di sistema Questo collettore accomoda
(9-pin PANEL1)
(vedi p.2 Nr. 18)
diverse funzioni di sistema
pannello frontale.
Italiano
Collegare l’interruttore d’alimentazione, l’interruttore di ripristino, l’indicatore di stato del sistema del pannello frontale del telaio a questo header in base all’assegnazione dei pin defi nita di seguito. Determinare i pin positivi e negativi prima di collegare i cavi.
PWRBTN (interruttore d’alimentazione):
Va collegato all’interruttore d’alimentazione del pannello frontale del telaio. Usando l’interruttore d’alimentazione si può confi gurare il modo in cui si spegne il sistema.
RESET (interruttore di ripristino):
Va collegato all’interruttore di ripristino del pannello frontale del telaio. Premere l’interruttore di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.
PLED (LED alimentazione del sistema):
Va collegato all’indicatore di stato d’alimentazione del pannello frontale del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua a lampeggiare quando il sistema è in stato di standby S1. Il LED è spento quando il sistema è in stato di sospensione /ibernazione S3/S4 oppure spento (S5).
70
ASRock Z68M/USB3 Motherboard
HDLED (LED attività disco rigido):
Va collegato al LED attività disco rigido del pannello frontale del telaio. Il LED è acceso quando disco rigido legge e scrive i dati.
Il design del pannello frontale può variare in base ai telai. Il modulo di un pannello frontale può consistere di: interruttore d’alimentazione, interruttore di ripristino, LED d’alimentazione, LED attività disco rigido, casse, eccetera. Quando si collega il modulo del pannello frontale a questo header, assicurarsi che l’assegnazione dei fi li e dei pin sia fatta corrispondere in modo appropriato.
Collettore casse telaio Collegare le casse del telaio a
(4-pin SPEAKER1)
(vedi p.2 Nr. 21)
questo collettore.
LED di accensione Collegare il LED di accensione
(3-pin PLED1)
(vedi p.2 Nr. 16)
chassi per indicare lo stato di
alimentazione del sistema. Il
1
PLED+
PLED+
PLED-
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
Collettori Chassis ed alimentazione ventola Collegare i cavi della ventola ai
(3-pin CHA_FAN1)
(vedi p.2 Nr. 17)
corrispondenti connettori
facendo combaciare il cavo
GND +12V CHA_FAN_SPEED
nero col pin di terra.
(3-pin PWR_FAN1)
(vedi p.2 Nr. 33)
PWR_FAN_SPEED
+12V
GND
Connettore ventolina CPU Collegare il cavo della ventolina
(4-pin CPU_FAN1)
(vedi p.2 Nr. 1)
CPU a questo connettore e far
combaciare il fi lo nero al pin
terra.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Sebbene la presente scheda madre disponga di un supporto per ventola CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in grado di funzionare anche senza la funzione di controllo della velocità della ventola. Se si intende collegare la ventola CPU a 3 piedini al connettore della ventola CPU su questa scheda madre, collegarla ai piedini 1-3.
Piedini 1-3 collegati
Installazione della ventola a 3 piedini
ASRock Z68M/USB3 Motherboard
Italiano
71
Connettore alimentazione ATX Collegare la sorgente
(24-pin ATXPWR1)
(vedi p.2 Nr. 5)
Con questa scheda madre, c’è in dotazione un
d’alimentazione ATX a questo
connettore.
12 124
13
12
connettore elettrico ATX a 24 pin, ma può funzionare lo stesso se si adotta un alimentatore ATX a 20 pin. Per usare l’alimentatore ATX a 20 pin, collegare l’alimentatore con il Pin 1 e il Pin 13.
24
Italiano
Installazione dell’alimentatore ATX a 20 pin
Connettore ATX 12 V Collegare un alimentatore ATX
(8-pin ATX12V1)
(vedi p.2 Nr. 2)
12 V a questo connettore.
8 5
4 1
1
13
Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX 12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura elettrica 4-pin ATX 12V, prego collegare la presa elettrica al Pin 1 e Pin 5.
Installazione elettrica 4-Pin ATX 12V
8 5
4 1
Collettore porta COM Questo collettore porta COM è
(9-pin COM1)
(vedi p.2 Nr. 26)
Header HDMI_SPDIF Header HDMI_SPDIF, con
(2-pin HDMI_SPDIF1)
(vedi p.2 Nr. 28)
utilizzato per supportare il
modulo porta COM.
uscita audio SPDIF su scheda
HDMI VGA, consente al
1
SPDIFOUT
GND
sistema di collegare dispositivi per TV digitale HDMI/proiettori/ LCD . Collegare il connettore HDMI_SPDIF della scheda VGA HDMI a questo header.
72
ASRock Z68M/USB3 Motherboard
2. Informazioni sul BIOS
La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF fi le) contenuto nel cd di supporto.
3. Software di supporto e informazioni su CD
Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 7 / 7 64-bit / VistaTM / Vista scheda madre contiene i driver e utilità necessari a potenziare le caratteristiche della scheda. Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata nel computer, apparirà automaticamente il Menù principale. Se il Menù principale non appare automaticamente, posizionarsi sul fi le “ASSETUP.EXE” nel CESTINO del CD di supporto e cliccare due volte per visualizzare i menù.
TM
64-bit / XP / XP 64-bit. Il CD di supporto a corredo della
ASRock Z68M/USB3 Motherboard
Italiano
73
1. Introducción
Gracias por su compra de ASRock Z68M/USB3 placa madre, una placa de confi an- za producida bajo el control de calidad estricto y persistente. La placa madre provee realización excelente con un diseño robusto conforme al compromiso de calidad y resistencia de ASRock. Esta Guía rápida de instalación contiene una introducción a la placa base y una guía de instalación paso a paso. Puede encontrar una información más detallada sobre la placa base en el manual de usuario incluido en el CD de soporte.
Porque las especifi caciones de la placa madre y el software de BIOS podrían ser actualizados, el contenido de este manual puede ser cambiado sin aviso. En caso de cualquier modifi cación de este manual, la versión actualizada estará disponible en el website de ASRock sin previo aviso. También encontrará las listas de las últimas tarjetas VGA y CPU soportadas en la página web de ASRock. Website de ASRock http://www.asrock.com Si necesita asistencia técnica en relación con esta placa base, visite nuestra página web con el número de modelo específi co de su placa. www.asrock.com/support/index.asp
1.1 Contenido de la caja
Placa base ASRock Z68M/USB3 (Factor forma Micro ATX: 24,4 cm x 21,8 cm, 9,6” x 8,6”) Guía de instalación rápida de ASRock Z68M/USB3 CD de soporte de ASRock Z68M/USB3 Dos cables de datos Serial ATA (SATA) (Opcional) Una protección I/O
Español
74
ASRock le recuerda...
Para mejorar el rendimiento en Windows® 7 / 7 64 bits / Vista 64 bits, es recomendable establecer la opción del BIOS de la confi gura- ción de almacenamiento en el modo AHCI. Para obtener detalles sobre la confi guración del BIOS, consulte el “Manual del usuario” que se en- cuentra en nuestro CD de soporte.
TM
/ VistaTM
ASRock Z68M/USB3 Motherboard
1.2 Especificación
Plataforma - Factor forma Micro ATX: 24,4 cm x 21,8 cm, 9,6” x 8,6”
- Todo diseño de Capacitor Sólido Procesador - Admite los procesadores Intel generación en el paquete LGA1155
- Diseño de fases de potencia 4 + 2
- Admite la tecnología Intel
- Admite procesador desbloqueado de la serie K
- Admite tecnología Hyper Threading (ver ATENCIÓN 1) Chipset - Intel
®
Z68
Memoria - Soporte de Tecnología de Memoria de Doble Canal (ver ATENCIÓN 2)
- 2 x DDR3 DIMM slots
- Apoya DDR3 2133(OC)/1866(OC)/1600/1333/1066 non-ECC, memoria de un-buffered
- Máxima capacidad de la memoria del sistema: 16GB (vea ATENCIÓN 3)
- Compatible con Intel
®
Ranuras de - 1 x ranura PCI Express 2.0 x16 (azul @ modo x16) Expansión - 2 x ranuras PCI Express 2.0 x1
- 1 x ranura PCI VGA OnBoard - Admite Intel
®
HD Graphics Built-in Visuals: Intel® Quick Sync Video, Intel® InTruTM 3D, Intel® Clear Video HD Technology, Intel® HD Graphics 2000/3000 e Intel® Advanced Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- 1759MB de Memoria máxima compartida (vea ATENCIÓN 4)
- Tres opciones de salida VGA: D-Sub, DVI-D y HDMI (ver ATENCIÓN 5)
- Admite HDMI 1.4a con una resolución máxima de 1920x1200 a 60 Hz
- Admite DVI con una resolución máxima de 1920x1200 a 60 Hz
- Admite D-Sub con una resolución máxima de 2048x1536 a 75 Hz
- Admite Sincronización automática entre audio y vídeo, xvYCC y HBR (audio de alta tasa de bits) con HDMI (se necesita un monitor compatible con HDMI) (ver ATENCIÓN 6)
- Admite la función HDCP con puertos DVI y HDMI
®
CoreTM i7 / i5 / i3 de segunda
®
Turbo Boost 2.0 Technology
Extreme Memory Profi le (XMP)
Español
ASRock Z68M/USB3 Motherboard
75
Español
- Apoya la reproducción de Blu-rayo de 1080p (BD) / HD-DVD con puertos DVI y HDMI Audio - 7.1 CH HD Audio con Protección de Contenido (Realtek ALC892 Audio Codec)
- Compatible con audio Blu-ray de alta calidad
TM
- Compatible con THX TruStudio LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Soporta Wake-On-LAN
- Admite detección de conexión de cable LAN
- Compatible con Ethernet 802.3az de bajo consumo energético
- Compatible con PXE Entrada/Salida I/O Panel de Panel - 1 x puerto de teclado PS/2 Trasero - 1 x Puerto D-Sub
- 1 x Puerto DVI-D
- 1 x puerto HDMI
- 1 x puerto de salida óptica SPDIF
- 4 x puertos USB 2.0 predeterminados
- 2 x puertos USB 3.0 predeterminados
- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/ENLACE y LED de VELOCIDAD)
- Conexión de audio: Altavoz lateral / Altavoz trasero / Central/Bajos / Entrada de línea / Altavoz frontal / Micrófono (ver ATENCIÓN 7) SATA 3 - 2 x conectores SATA3 de 6,0 Gb/s con funciones RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage y tecnología Intel Smart Response), NCQ, AHCI y de “Hot Plug” (conexión en caliente) USB 3.0 - 2 x puertos USB 3.0 traseros de Etron EJ168A, compatible con USB 1.0/2.0/3.0 de hasta 5 GB/s Conectores - 4 x conexiones SATA2, admiten una velocidad de transferencia de datos de hasta 3,0Gb/s, soporta RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage y tecnología Intel Smart Response), NCQ, AHCI y “Conexión en caliente”
- 2 x conexiones SATA3, admiten una velocidad de transferencia de datos de hasta 6,0Gb/s
- 1 x puerto Floppy
- 1 x Cabezal de Módulo Infrarrojos
76
ASRock Z68M/USB3 Motherboard
- 1 x Base de conexiones del módulo de infrarrojos para el
consumidor
- 1 x cabecera de puerto de impresora
- 1x En-tête de port COM
- 1 x cabecera HDMI_SPDIF
- 1 x cabecera de indicador LED de encendido
- Conector de ventilador de CPU / chasis / alimentación
- 24-pin cabezal de alimentación ATX
- 8-pin conector de ATX 12V power
- Conector de audio de panel frontal
- 3 x Cabezal USB 2.0 (admite 6 puertos USB 2.0 adicionales) BIOS - 64Mb AMI BIOS
- BIOS legal UEFI AMI compatible con GUI
- Soporta “Plug and Play”
- ACPI 1.1 compliance wake up events
- Soporta “jumper free”
- Soporta SMBIOS 2.3.1
- Múltiple ajuste de IGPU, DRAM, PCH, CPU PLL, VTT, VCCSA Voltage CD de soport - Controladores, utilidades, software de antivirus (versión de prueba), Prueba de CyberLink MediaEspresso 6.5, conjunto de aplicaciones ASRock (CyberLink DVD Suite - OEM y versión de prueba; Conjunto multimedia ASRock MAGIX
- OEM)
Característica - ASRock Extreme Tuning Utility (AXTU) (vea ATENCIÓN 8) Única - ASRock Instant Boot
- ASRock Instant Flash (vea ATENCIÓN 9)
- ASRock APP Charger (vea ATENCIÓN 10)
- ASRock SmartView (vea ATENCIÓN 11)
- ASRock XFast USB (vea ATENCIÓN 12)
- ASRock XFast LAN (vea ATENCIÓN 13)
- Lucid Virtu (vea ATENCIÓN 14)
- Amplifi cador Híbrido:
- Stepless control de frecuencia de CPU (vea ATENCIÓN 15)
- ASRock U-COP (vea ATENCIÓN 16)
- Protección de Falla de Inicio (B.F.G..)
- Opción de refrigeración combinada (C.C.O.) (vea ATENCIÓN 17)
- Indicador LED nocturno Monitor - Sensibilidad a la temperatura del procesador Hardware - Sensibilidad a la temperatura de la placa madre
ASRock Z68M/USB3 Motherboard
Español
77
- Taquímetros de los ventiladores del procesador y del CPU / chasis / alimentación
- Ventilador silencioso del procesador y el chasis (ajuste automático de la velocidad del ventilador del chasis en función de la temperatura del procesador)
- Control de ajuste de la velocidad del ventilador de la CPU
- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore
®
OS - En conformidad con Microsoft
Windows® 7 / 7 64 bits /
VistaTM / VistaTM 64 bits / XP / XP 64 bits Certi caciones - FCC, CE, WHQL
- Cumple con la directiva ErP/EuP (se requiere una fuente de alimentación que cumpla con la directiva ErP/EuP) (vea ATENCIÓN 18)
* Para más información sobre los productos, por favor visite nuestro sitio web: http://www.asrock.com
ADVERTENCIA
Tenga en cuenta que hay un cierto riesgo implícito en las operaciones de aumento de la velocidad del reloj, incluido el ajuste del BIOS, aplicando la tecnología de aumento de velocidad liberada o utilizando las herramientas de aumento de velocidad de otros fabricantes. El aumento de la velocidad puede afectar a la estabilidad del sistema e, incluso, dañar los componentes y dispositivos del sistema. Esta operación se debe realizar bajo su propia responsabilidad y Ud. debe asumir los costos. No asumimos ninguna responsabilidad por los posibles daños causados por el aumento de la velocidad del reloj.
Español
78
ATENCIÓN !
1. Por favor consulte página 48 del Manual del Usuario en el soporte CD sobre la confi guración de Hyper-Threading Technology.
2. Esta placa base soporta Tecnología de Memoria de Doble Canal. Antes de implementar la Tecnología de Memoria de Doble Canal, asegúrese de leer la guía de instalación de módulos de memoria en la página 15 para su correcta instalación.
3. Debido a las limitaciones del sistema, el tamaño real de la memoria debe ser inferior a 4GB para que el sistema pueda funcionar bajo Windows 7 / VistaTM / XP. Para equipos con Windows® OS con CPU de 64-bit, no existe dicha limitación.
4. El tamaño de la memoria compartido máximo es defi nido por el vendedor del chipset y está conforme al cambio. Por favor compruebe el Web site
®
de Intel
para la información más última.
5. Puede elegir entre dos de los tres monitores solamente. Los monitores D-Sub, DVI-D y HDMI no se pueden habilitar al mismo tiempo. Además, con el adaptador DVI a HDMI, el puerto DVI-D puede admitir las mismas funciones que el puerto HDMI.
ASRock Z68M/USB3 Motherboard
®
6. Las funciones xvYCC y Deep Color solamente se admiten con el sistema operativo Windows® 7 de 64 bits/ 7. El modo Deep Color solamente se habilitará si la pantalla admite 12 bpc en EDID. HBR se admite en Win­dows® 7 64 bits / 7 / VistaTM 64 bits / VistaTM.
7. Para la entrada de micrófono, esta placa madre ofrece soporte para modos estéreo y mono. Para salida de audio, este placa madre ofrece soporte para modos de 2 canales, 4 canales, 6 canales y 8 canales. Consulte la tabla en la página 3 para una conexión correcta.
8. ASRock Extreme Tuning Utility (AXTU) es una herramienta todo en uno que permite realizar ajustes precisos en diferentes funciones del sistema mediante una interfaz sencilla, que incluye supervisión de hardware, control de ventiladores, función de aumento de la velocidad del reloj, DNA OC y IES. La función de supervisión de hardware, muestra las principales lecturas del sistema. La función de control de los ventiladores, muestra la velocidad y la temperatura de los ventiladores y
permite ajustarlas. La función de aumento de la velocidad del
reloj, permite aumentar la frecuencia de la CPU para conseguir un rendimiento óptimo del sistema. La función DNA OC permite guardar la confi guración OC como un perfi l y compartirla con sus amigos. Después, sus amistados pueden cargar el perfi l OC en sus propios sistemas para obtener la misma confi guración OC. En el protector de energía inteligente (IES, Intelligent Energy Saver), el regulador de voltaje puede reducir el número de fases de salida para mejorar la efi ciencia cuando los núcleos de la CPU están inactivos sin que el rendimiento de cálculo disminuya. Visite nuestro sitio Web para obtener los procedimientos de funcionamiento de ASRock Extreme Tuning Utility (AXTU).
Sitio Web de ASRock: http://www.asrock.com
9. ASRock Instant Flash es una utilidad de programación del BIOS que se encuentra almacenada en la memoria Flash ROM. Esta sencilla her­ramienta de actualización de BIOS le permitirá actualizar el BIOS del sistema sin necesidad de acceder a ningún sistema operativo, como MS­DOS o Windows durante la fase POST o pulsar <F2> para acceder al menú de confi gu- ración del BIOS y a la utilidad ASRock Instant Flash. Ejecute esta herra­mienta y guarde el archivo correspondiente al sistema BIOS nuevo
en su unidad fl ash USB, unidad de disco fl exible o disco duro para poder
actualizar el BIOS con sólo pulsar un par de botones, sin necesidad de preparar un disco fl exible adicional ni utilizar complicadas utilidades de programación. Recuerde que la unidad fl ash USB o disco duro utilizado debe disponer del sistema de archivos FAT32/16/12.
10. Si desea una forma más rápida y menos limitada de cargar sus disposi­tivos de Apple; como por ejemplo iPhone, iPod o iPad Touch, ASRock ha creado una fantástica solución para usted: ASRock APP Charger. Simplemente mediante la instalación del controlador de APP Charger, podrá cargar su iPhone de forma mucho más rápida que antes, hasta un
40%, desde su equipo. ASRock APP Charger le permite cargar de forma rápida muchos dispositivos de Apple simultáneamente e incluso podrá
®
. Gracias a esta utilidad, sólo necesitará pulsar <F6>
Español
ASRock Z68M/USB3 Motherboard
79
Español
continuar la carga cuando su PC entre en modo de espera (S1), suspen-
dido en RAM (S3), modo de hibernación (S4) o se apague (S5). Una vez instalado el controlador de APP Charger, podrá disfrutar fácilmente de una fantástica carga sin precedentes.
Sitio web de ASRock: http://www.asrock.com/Feature/AppCharger/index.
asp
SmartView, una nueva función el explorador de Internet, es la página de
11.
inicio inteligente para IE que combina los sitios Web más visitados, su historial, sus amigos de Facebook y su fuente de noticias en una vista mejorada para disfrutar de una experiencia en Internet más personal. Las placas base ASRock están exclusivamente equipadas con la utilidad SmartView que le ayuda a seguir en contacto con sus amigos sobre la marcha. Para utilizar la función SmartView asegúrese de que la versión de su sistema operativo es Windows bits y que la versión de su explorador es IE8. Sitio Web de ASRock:
http://www.asrock.com/Feature/SmartView/index.asp
12. ASRock XFast USB puede aumentar el rendimiento de los dispositivos de almacenamiento USB. El rendimiento depende de las propiedades del dispositivo.
13. ASRock XFast LAN proporciona un acceso a Internet más rápido, que incluye las ventajas que se indican a continuación. Priorización de aplicaciones LAN: Puede confi gurar la prioridad de las aplicaciones de forma ideal y/o agregar nuevos programas. Menor latencia en los juegos: Después de aumentar la prioridad de los juegos en línea, se puede reducir la latencia en los mismos. Gestionar el tráfi co: Puede ver vídeo en alta defi nición de Youtube y descargar archivos simultáneamente. Análisis de sus datos en tiempo real: Con la ventana de estado, puede reconocer fácilmente qué transmisiones en secuencias se están trans­ riendo actualmente.
14. Con la tecnología Lucid Virtu, puede disfrutar de las ventajas del ren­dimiento 3D de la GPU discreta y de las funciones avanzadas multime­dia de la tarjeta gráfi ca HD de Inte
15. Aunque esta placa base ofrece un control complete, no es recomendable forzar la velocidad. Las frecuencias de bus de la CPU distintas a las re­comendadas pueden causar inestabilidad en el sistema o dañar la CPU.
16. Cuando la temperatura de CPU está sobre-elevada, el sistema va a apagarse automaticamente. Antes de reanudar el sistema, compruebe si el ventilador de la CPU de la placa base funciona apropiadamente y desconecte el cable de alimentación, a continuación, vuelva a conec­tarlo. Para mejorar la disipación de calor, acuérdese de aplicar thermal grease entre el procesador y el disipador de calor cuando usted instala el sistema de PC.
17. La opción de refrigeración combinada (C.C.O.) representa una opción
exible que puede adaptarse a tres tipos de disipador de CPU diferentes, correspondientes a los zócalos LGA 775, LGA 1155 y LGA 1156. Recu­erde que no es posible el uso de todos los ventiladores para CPU 775 y
1156.
®
7 / 7 64 bits / VistaTM / VistaTM 64
.
80
ASRock Z68M/USB3 Motherboard
18. EuP, siglas de Energy Using Product (Producto que Utiliza Energía), es una disposición regulada por la Unión Europea para establecer el consumo total de energía de un sistema. Según la disposición EuP, la alimentación de CA total para el sistema completo ha de ser inferior a 1,00W en modo apagado. Para cumplir con el estándar EuP, se re­quieren una placa base y una fuente de alimentación que cumplan con la directiva EuP. Según las directrices de Intel, una fuente de alimentación que cumpla con la directiva EuP debe satisfacer el estándar, es decir, la efi ciencia de energía de 5v en modo de espera debería ser mayor del 50% con un consumo de corriente de 100mA. Para seleccionar una fuente de alimentación que cumpla la directiva EuP, le recomendamos que consulte con el fabricante de la fuente de alimentación para obtener más detalles.
1.3 Setup de Jumpers
La ilustración muestra como los jumpers son confi gurados. Cuando haya un jumper- cap sobre los pins, se dice gue el jumper está “Short”. No habiendo jumper cap sobre los pins, el jumper está “Open”. La ilus­tración muesta un jumper de 3 pins cuyo pin 1 y pin 2 están “Short”.
Jumper Setting
Limpiar CMOS
(CLRCMOS1, jumper de 3 pins) (ver p.2, No. 9)
Nota:
Valor predetermi­nado
Restablecimiento de
la CMOS
CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los parámetros del sistema y restablecer la confi guración predeterminada de los mismos, apague el equipo y desenchufe el cable de alimentación de la toma de corriente eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perfi l predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se borrará si la batería CMOS se quita.
para
Español
ASRock Z68M/USB3 Motherboard
81
1.4 Cabezales y Conectores en Placas
Los conectores y cabezales en placa NO son puentes. NO coloque las cubiertas de los puentes sobre estos cabezales y conectores. El colocar cubiertas de puentes sobre los conectores y cabezales provo­cará un daño permanente en la placa base.
Conector de disquetera
(33-pin FLOPPY1) (vea p.2, N. 25)
Atención: Asegúrese que la banda roja del cable queda situado en el mismo lado que el contacto 1 de la conexión.
Conexiones de serie ATAII Estas cuatro conexiones de
(SATA2_2: vea p.2, N. 13)
(SATA2_3: vea p.2, N. 12)
(SATA2_4: vea p.2, N. 14)
(SATA2_5: vea p.2, N. 15)
permite una velocidad de transferencia de 3.0 Gb/s.
Conexiones de serie ATA3 Estas dos conexiones de
(SATA3_0: vea p.2, N. 7)
(SATA3_1: vea p.2, N. 8)
de almacenamiento internos. La interfaz SATAII / SATA3 actual permite una velocidad de transferencia de 6.0 Gb/s.
la banda roja debe quedar en el mismo lado que el contacto 1
SATA2_3 SATA2_2
serie ATAII (SATAII) admiten cables SATA para dispositivos de almacenamiento internos. La interfaz SATAII actual
serie ATA3 (SATA3) admiten
cables SATA para dispositivos
SATA2_5 SATA2_4
SATA3_0
SATA3_1
Español
82
Cable de datos de Cualquier extremo del cable de serie ATA (SATA) los datos de SATA puede ser
(Opcional)
conectado con el disco duro de SATA / SATAII / SATA3 o el conectador de SATAII / SATA3 en esta placa base.
ASRock Z68M/USB3 Motherboard
Cabezal USB 2.0 Además de cuatro puertos
(9-pin USB6_7)
(vea p.2, N. 22)
USB 2.0 predeterminados en el
panel de E/S, hay tres bases de conexiones USB 2.0 en esta placa base. Cada una de estas bases de conexiones
(9-pin USB8_9)
(vea p.2, N. 20)
(9-pin USB10_11) (vea p.2, N. 19)
admite dos puertos USB 2.0.
1
1
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
P+9
P+8
P+11
P+10
GND
GND
GND
GND
DUMMY
DUMMY
Cabezal de Módulo Infrarrojos Este cabezal soporta un
(5-pin IR1)
módulo infrarrojos de
(vea p.2, N. 6)
transmisión y recepción
wireless opcional.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Base de conexiones del módulo de Esta base de conexiones se infrarrojos para el consumidor puede utilizar para conectar
(4-pin CIR1)
(vea p.2, N. 23)
dispositivos infrarrojos del
consumidor opcionales, como
1
ATX+5VSB
IRRX
IRTX
GND
por ejemplo equipos HI-FI, descodifi cadores de TV, etc.
Cabecera de puerto de impresora Esta es una interfaz de puerto
(LPT1 de 25 terminales)
(vea p.2, N. 24)
permite conectar cómodamente dispositivos de impresión.
Conector de audio de Este es una interface para panel frontal cable de audio de panel frontal
(9-pin HD_AUDIO1)
(vea p.2, N. 27)
conveniente de apparatos de
Audio.
AFD#
para cable de impresora que
ERROR#
PINIT#
SLIN#
1
SPD2
SPD1
SPD0
STB#
SPD3
SPD4
SPD6
SPD5
GND
PRESENCE#
GND
SPD7
MIC_RET
ACK#
BUSY
OUT_RET
PE
SLCT
que permite conexión y control
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
ASRock Z68M/USB3 Motherboard
Español
83
1. El Audio de Alta Defi nición soporta la detección de conector, pero el cable de panel en el chasis debe soportar HDA para operar correctamente. Por favor, siga las instrucciones en nuestro manual y en el manual de chasis para instalar su sistema.
2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido del panel frontal de la siguiente manera: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L. C. Conecte Ground (GND) a Ground (GND).
D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No
necesitará conectarlos al panel de sonido AC’97. E. Activación del micrófono frontal. En sistemas operativos Windows Seleccione “Mixer” (Mezclador). Seleccione “Recorder” (Grabadora). A continuación, haga clic en “FrontMic” (Micrófono frontal). En sistemas operativos Windows Acceda a la fi cha “FrontMic” (Micrófono frontal) del panel de control Realtek. Ajuste la posición del control deslizante “Recording Volume” (Volumen de grabación).
®
XP / XP 64-bit:
®
7 / 7 64-bit / VistaTM / VistaTM 64-bit:
Cabezal de panel de sistema Este cabezar acomoda varias
(9-pin PANEL1)
(vea p.2, N. 18)
Conecte el interruptor de alimentación, el interruptor de restablecimiento y el indicador de estado del sistema situados en el chasis con esta cabecera en función de las siguientes asignaciones de contacto. Preste atención a los contactos positivos y negativos antes de conectar los cables.
dunciones de panel frontal de
sistema.
Español
84
PWRBTN (interruptor de alimentación):
Conecte el interruptor de encendido situado en el panel frontal del
chasis. Puede confi gurar la forma de apagar su sistema mediante el
interruptor de alimentación. RESTABLECER (interruptor de restablecimiento):
Conecte el interruptor de restablecimiento situado en el panel frontal del
chasis. Pulse el interruptor de restablecimiento para restablecer el
equipo si se bloquea y no se reinicia con normalidad. PLED (LED de alimentación del sistema):
Conecte el indicador de estado de alimentación situado en el panel
frontal del chasis. El LED se enciende cuando el sistema esté en
funcionamiento. El LED parpadea cuando el sistema se encuentre en
estado de suspensión S1. El LED se apaga cuando el sistema se
encuentre en estado de suspensión S3/S4 o se apaga (S5).
ASRock Z68M/USB3 Motherboard
HDLED (LED de actividad del disco duro):
Conecte el LED de actividad de disco duro situado en el panel frontal del chasis. El LED se enciende cuando el disco duro esté leyendo o escribiendo datos.
Es posible que el diseño del panel frontal varíe en función del chasis. Un módulo del panel frontal consiste principalmente de interruptor de alimentación, interruptor de restablecimiento, LED de alimentación, LED de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel frontal del chasis a esta cabecera, asegúrese de que las asignaciones de cables y las asignaciones de contactos coincidan correctamente.
Cabezal del altavoz del chasis Conecte el altavoz del chasis a
(4-pin SPEAKER1)
(vea p.2, N. 21)
su cabezal.
Cabecera de indicador LED de encendido Conecte el indicador LED de
(3-pin PLED1)
(vea p.2, N. 16)
estado de encendido del
encendido del chasis a esta
cabecera para conocer el
1
PLED+
PLED+
PLED-
sistema. El indicador LED se encenderá si el sistema se encuentra en funcionamiento. El indicador LED parpadeará en el estado S1. El indicador LED se apagará en los estados S3/S4 o S5 (apagado).
Conectores de ventilador de chasis y alimentación
(3-pin CHA_FAN1)
(vea p.2, N. 17)
(3-pin PWR_FAN1)
(vea p.2, N. 33)
Conector del ventilador Conecte el cable del ventilador de la CPU de la CPU a este conector y
(4-pin CPU_FAN1)
(vea p.2, N. 1)
haga coincidir el cable negro
con el conector de tierra.
GND +12V CHA_FAN_SPEED
PWR_FAN_SPEED
+12V
GND
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Por favor, conecte los cables del ventilador a los conectores de ventilador, haciendo coincidir el cable negro con la patilla de masa.
ASRock Z68M/USB3 Motherboard
Español
85
Aunque esta placa base proporciona compatibilidad para un ventilador (silencioso) de procesador de 4 contactos, el ventilador de procesador de 3 contactos seguirá funcionando correctamente incluso sin la función de control de velocidad del ventilador. Si pretende enchufar el ventilador de procesador de 3 contactos en el conector del ventilador de procesador de esta placa base, conéctelo al contacto 1-3.
Contacto 1-3 conectado
Instalación del ventilador de 3 contactos
Español
Cabezal de alimentación ATX Conecte la fuente de
(24-pin ATXPWR1)
(vea p.2, N. 5)
A pesar de que esta placa base incluye in conector de alimentación ATX de 24 pins, ésta puede funcionar
alimentación ATX a su cabezal.
12 124
13
12
24
incluso si utiliza una fuente de alimentación ATX de 20 pins tradicional. Para usar una fuente de alimentación ATX de 20 pins, por favor, conecte su fuente de alimentación usando los Pins 1 y 13.
Instalación de una Fuente de Alimentación ATX de 20 Pins
1
13
Conector de ATX 12V power Tenga en cuenta que es
(8-pin ATX12V1)
(vea p.2, N. 2)
corriente con el enchufe ATX
necesario conectar este
conector a una toma de
8 5
4 1
12V, de modo que proporcione sufi ciente electricidad. De lo contrario no se podrá encender.
Aunque esta placa base proporciona un conector de energía de 8-pin ATX 12V, puede todavía trabajar si usted adopta un fuente tradicional de energía de 4-pin ATX 12V. Para usar el fuente de energía de 4-pin ATX 12V, por favor conecte su fuente de energía junto con Pin 1 y Pin 5.
8 5
86
Instalación de Fuente de Energía de 4-Pin ATX 12V
ASRock Z68M/USB3 Motherboard
4 1
Cabezal del puerto COM Este cabezal del puerto COM
(9-pin COM1)
(vea p.2, N. 26)
se utiliza para admitir un
módulo de puerto COM.
Cabecera HDMI_SPDIF Cabecera HDMI_SPDIF. Ofrece
(HDMI_SPDIF1 de 2 pin)
(vea p.2, N. 28)
VGA HDMI, permite al sistema
una salida SPDIF la tarjeta
1
GND
SPDIFOUT
conectarse a dispositivos de TV Digital HDMI / proyectores / Dispositivos LCD. Conecte el conector HDMI_SPDIF de la tarjeta VGA HDMI a esta cabecera.
ASRock Z68M/USB3 Motherboard
Español
87
2. BIOS Información
El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up (POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> + <Borrar>, o apretando el botón Reset en el panel del ordenador. Para información detallada sobre como confi gurar la BIOS, por favor refi érase al Manual del Usuario (archivo PDF) contenido en el CD.
3. Información de Software Support CD
Esta placa-base soporta diversos tipos de sistema operativo Windows®: 7 / 7 64 bits / VistaTM / Vista la placa-base trae todos los drivers y programas utilitarios para instalar y confi gurar la placa-base. Para iniciar la instalación, ponga el CD en el lector de CD y se des­plegará el Menú Principal automáticamente si «AUTORUN» está habilitado en su computadora. Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el ar­chivo “ASSETUP.EXE” para iniciar la instalación.
TM
64 bits / XP / XP 64 bits. El CD de instalación que acompaña
Español
88
ASRock Z68M/USB3 Motherboard
1. Введение
Благодарим вас за покупку материнской платы ASRock Z68M/USB3 надежной материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock жесткими требованиями к качеству. Она обеспечивает превосходную производительность и отличается отличной конструкцией, которые отражают приверженность ASRock качеству и долговечности. Данное руководство по быстрой установке включает вводную информацию о материнской плате и пошаговые инструкции по ее установке. можно найти в руководстве пользователя на компакт-диске поддержки.
Спецификации материнской платы и программное обеспечение BIOS иногда изменяются, поэтому содержание этого руководства может обновляться без уведомления. В случае любых модификаций руководства его новая версия будет размещена на веб-сайте ASRock без специального уведомления. Кроме того, самые свежие списки поддерживаемых модулей памяти и процессоров можно найти на сайте ASRock. Адрес веб-сайта ASRock http://www.asrock.com При необходимости технической поддержки по вопросам данной материнской платы посетите наш веб-сайт для получения информации об используемой модели. www.asrock.com/support/index.asp
1.1 Комплектность
Материнская плата ASRock Z68M/USB3 (форм-фактор Micro ATX: 9,6 x 8,6 дюйма / 24,4 x 21,8 см)
Руководство по быстрой установке ASRock Z68M/USB3 Компакт-диск поддержки ASRock Z68M/USB3
2 x кабель данных Serial ATA (SATA) (дополнительно) 1 x I/O Щит Группы ввода / вывода
Более подробные сведения о плате
ASRock напоминает...
Для обеспечения максимальной производительности ОС Windows 7 / 7 64-bit / Vista
параметра Storage Configuration (Конфигурация запоминающего устройства) режим AHCI. Подробные сведения о настройке BIOS см. в руководстве пользователя на прилагаемом компакт-диске.
TM
/ VistaTM 64-bit рекомендуется в BIOS выбрать для
ASRock Z68M/USB3 Motherboard
®
Русский
89
Русский
1.2 Спецификации
Платформа - форм-фактор Micro ATX: 9,6 x 8,6 дюйма / 24,4 x 21,8 см
- Весь Твердый Конденсаторный проект Процессор - Поддержка процессоров Intel исполнении LGA1155
- Технология 4 + 2 Power Phase Design
- Поддержка технологии Intel
- Поддержка разблокированного ЦП серии K
- Поддержка технологии Hyper-Threading (см. ОСТОРОЖНО, пункт 1) Набор микросхем - Intel
®
Z68
Память - Поддержка технологии Dual Channel DDR3 Memory Technology (см. ОСТОРОЖНО, пункт 2)
- 2 x гнезда DDR3 DIMM
- Поддержите DDR3 2133(OC)/1866(OC)/1600/1333/1066 не- ECC, безбуферная память
- Максимальный объем системной памяти: 16 ГБ (см. ОСТОРОЖНО, пункт 3)
- поддержка профиля Intel
Гнезда - 1 x PCI Express 2.0 x16 (Синий в режиме x16) расширения - 2 x PCI Express 2.0 x1
- 1 x гнезда PCI Графика - Поддержка функций встроенных видеоадаптеров Intel Quick Sync Video, Intel Intel® HD Graphics 2000/3000, Intel® Advanced Vector Extensions (AVX)
- Pixel Shader 4.1, DirectX 10.1
- Макс. объем разделяемой памяти 1759Мб (см. ОСТОРОЖНО, пункт 4)
- Три VGA-выхода: D-Sub, DVI-D и HDMI (см. ОСТОРОЖНО, пункт 5)
- Поддержка HDMI 1.4a с максимальным разрешением до 1920х1200 @ 60 Гц
- Поддержка DVI с максимальным разрешением до 1920х1200 @ 60 Гц
- Поддержка D-Sub с максимальным разрешением до 2048х1536 @ 75 Гц
- Поддержка Auto Lip Sync, xvYCC и HBR (High Bit Rate Audio) через HDMI (необходим монитор с разъемом HDMI) (см. ОСТОРОЖНО, пункт
- Поддержка функции HDCP через разъемы DVI и HDMI
- Подержат Blu-луч 1080p (КОММУТАЦИОННАЯ ДОСКА) / воспроизведение HD-DVD через разъемы DVI и HDMI Аудиосистема - 7.1 CH HD Аудио HD с Довольной Защитой (Кодер-декодер Аудио Realtek ALC892)
- Поддержка Premium Blu-ray audio
- Поддержка технологии THX TruStudio ЛВС - PCIE x 1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
90
ASRock Z68M/USB3 Motherboard
®
CoreTM i7 / i5 / i3 2-го поколения в
®
Turbo Boost 2.0
®
Extreme Memory Profi le (XMP)
®
®
InTruTM 3D, технологии Intel® Clear Video HD,
6)
TM
HD: Intel®
- поддержка Wake-On-LAN
- Поддержка определения кабеля ЛВС
- Поддержка энергосберегающего интерфейса Ethernet 802.3az
- Поддержка PXE Разъемы ввода- I/O Panel вывода на задней - 1 x порт клавиатуры PS/2 панели - 1 x D-Sub порт
- 1 x DVI-D порт
- 1 x HDMI порт
- 1 x порт Optical SPDIF Out
- 4 x порта USB 2.0 на задней панели в стандартной конфигурации
- 2 x порта USB 3.0 на задней панели в стандартной конфигурации
- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор ACT/LINK и индикатор SPEED)
- Соединитель звуковой подсистемы / субвуфер / линейный вход / передняя колонка / микрофон (см. ПРЕДУПРЕЖДЕНИЕ 17) SATA 3 - 2 x порта SATA3 со скоростью передачи данных 6,0 Гбит/с, с аппаратной поддержкой функций RAID (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage и технологии Intel Smart Response), NCQ, AHCI и «горячего подключения» USB 3.0 - 2 x задних порта USB 3.0 на контроллере Etron EJ168A с поддержкой интерфейсов USB 1.0/2.0/3.0 и скорости передачи данных до 5 Гбит/с Колодки и - 4 x разъема SATA2 3,0 плате (RAID 0, RAID 1, RAID 10, RAID 5, Intel Rapid Storage и технологии Intel Smart Response), NCQ, AHCI и «горячего подключения»
- 2 x разъема SATA3 6,0 Гбит/с
- 1 x Порт гибкого диска
- 1 x Разъем порта печати
- 1 x
- 1 x Разъем порта печати
- 1 x Колодка COM
- 1 x Колодка HDMI_SPDIF
- 1 x разъем Power LED
- соединитель: CPU/Chassis/Power FAN
- 24-контактный Колодка питания ATX
- 8-контактный Разъем ATX 12 В
- Аудиоразъем передней панели
- 3 x Колодка USB 2.0 (одна колодка для поддержки 6 дополнительных портов USB 2.0 BIOS - 64Mb AMI BIOS
- AMI UEFI Legal BIOS с поддержкой графического интерфейса поль зователя
- поддержка “Plug and Play”
- ACPI 1.1, включение по событиям
- поддержка режима настройки без перемычек
- поддержка SMBIOS 2.3.1
Датчик пользовательского инфракрасного модуля
Гбит/с, поддержка функций RAID
: тыльная колонка / центральная
ASRock Z68M/USB3 Motherboard
Русский
91
Русский
- центральный IGPU, DRAM, Мультирегулирование Напряжения PCH, CPU PLL, VTT, VCCSA Компакт- - Драйверы, служебные программы, антивирусное программное диск обеспечение (пробная версия), Пробная версия программы поддержки CyberLink MediaEspresso 6.5, пакет программ ASRock (CyberLink DVD Suite – OEM-версия и пробная версия; ASRock MAGIX Multimedia Suite - поставщик) Уникальная - Средство ASRock Extreme Tuning Utility (AXTU) Особенность (см. ОСТОРОЖНО, пункт 8)
- ASRock Instant Boot
- ASRock Instant Flash (см. ОСТОРОЖНО, пункт 9)
- ASRock APP Charger (см. ОСТОРОЖНО, пункт 10)
- ASRock SmartView (см. ОСТОРОЖНО, пункт 11)
- ASRock XFast USB (см. ОСТОРОЖНО, пункт
- ASRock XFast LAN (см. ОСТОРОЖНО, пункт 13)
- Lucid Virtu (см. ОСТОРОЖНО, пункт 14)
- Hybrid Booster:
- плавная настройка частоты процессора (см. ОСТОРОЖНО, пункт 15)
- ASRock U-COP (см. ОСТОРОЖНО, пункт 16)
- Защита от сбоев загрузки Boot Failure Guard (B.F.G)
- Combo Cooler Option (C.C.O.) (см. ОСТОРОЖНО, пункт 17)
- Ночное LED-освещение Контроль - Датчики температуры процессора оборудо- - Датчики температуры корпуса вания - Тахометры вентиляторов CPU/Chassis/Power FAN
- Бесшумный вентилятор ЦП/системного блока (возможность матической настройки скорости вентилятора системного блока в соответствии с температурой центрального процессора)
- Мультиконтроль скорости вентилятора ЦП
- Контроль= напряжения: +12V, +5V, +3.3V, Vcore Операцион - Совместимость с Microsoft Поддержка 64-разрядной версии VistaTM / XP / XP 64-bit ные - FCC, CE, WHQL системы - Совместимость с ErP/EuP Ready (требуется блок питания Сертификаты совместимый с ErP/EuP) (см. ОСТОРОЖНО, пункт 18) * Для детальной информации продукта, пожалуйста посетите наш вебсайт: http://www.asrock.com
ВНИМАНИЕ
Следует понимать, что с оверклокингом связан определенный риск во всех случаях, включая изменение установок BIOS, применение технологии Untied Overclocking или использование инструментов оверклокинга сторонних производителей. Оверклокинг может повлиять на стабильность работы системы и даже вызвать повреждение входящих в нее компонентов и устройств. Приступая к оверклокингу, вы полностью берете на себя связанные с ним риски и расходы. Мы не будем нести ответственность за любые возможные повреждения в результате оверклокинга.
®
Windows® 7 / 7 64-bit / Vista
12)
TM
все
92
ASRock Z68M/USB3 Motherboard
авто
/
ОСТОРОЖНО!
1. Информацию об установке параметров гиперпоточной технологии (Hyper- Threading Technology) вы найдете на стр. 48 Руководства пользователя на компакт-диске поддержки.
2. Данная материнская плата поддерживает технологию двухканальной
памяти Dual Channel Memory Technology. Перед ее использованием не забудьте прочитать инструкции по правильной установке модулей памяти в руководстве по установке (стр. 15).
3. В силу ограничения операционной системы фактическая емкость памяти может использования системой Windows® 7 / VistaTM / XP. Таких ограничений нет для Windows® OS с 64-bit центральным процессором.
4. Максимальная совместная емкость памяти определена продавцем микропроцессорного набора и может измениться. Входите в Intel® веб­сайт за последние информации, пожалуйста.
5. Вы можете использовать только два разъема из трех для вывода изображения одновременно. Задействовать сразу три подключения ­D-Sub, DVI-D и HDMI - невозможно. При помощи адаптера DVI-to-HDMI порт DVI-D будет поддерживать те же функции, что и HDMI.
6. Функции xvYCC и Deep Color поддерживаются только в Windows бит / 7. Функция Deep Color будет включена только в том случае, если монитор поддерживает функцию EDID (12-битные цветовые каналы). Функция HBR поддерживается только в Windows бит / VistaTM.
7. Поддерживается работа микрофонного входа в режимах моно и стерео. Поддерживаются 2-, 4-, 6- и 8-канальный режимы вывода звука. Соответствующие схемы подключения описаны на стр. 3.
8.
Служебная программа ASRock Extreme Tuning Utility (AXTU) – это универсальное средство тонкой настройки различных функций системы с удобным и понятным интерфейсом, включающая разделы Hardware
Monitor (Наблюдение за оборудованием), Fan Control (Управление
вентилятором), Overclocking («Разгон» процессора), OC DNA (Параметры
«разгона») and IES (Автоматическое энергосбережение). В разделе Hardware Monitor (Наблюдение за оборудованием) отображаются
основные характеристики аппаратных средств системы. В разделе Fan
Control (Управление вентилятором) отображается скорость вентилятора и температура, («Разгон» процессора) можно увеличить рабочую частоту ЦПУ, чтобы добиться оптимальной производительности системы. В разделе OC DNA (Параметры «разгона») можно сохранить настройки «разгона»
процессора в виде профиля, который потом можно предложить для
использования своим друзьям. Друзья смогут загрузить профиль «разгона» на свои компьютеры и получить аналогичный результат
разделе IES (Автоматическое энергосбережение) можно настроить регулятор напряжения так, что он будет уменьшать количество
работающих линий питания, чтобы поднять КПД системы без ущерба для
ее производительности во время простоя ядер ЦПУ. Чтобы узнать, как
быть меньше 4Гб для обеспечения резервного места для
®
7 64-
®
7 64-бит / 7 / VistaTM 64-
которые можно регулировать. В разделе Overclocking
. В
ASRock Z68M/USB3 Motherboard
Русский
93
Русский
работать с программой ASRock Extreme Tuning Utility (AXTU), посетите
наш сайт в Интернете. Адрес сайта ASRock: http://www.asrock.com
9. ASRock Instant Flash – программа для прошивки BIOS, встроенная в
Flash ROM. Данное средство для обновления BIOS умеет работать
без входа в операционные системы, вроде MS-DOS или Windows Чтобы запустить программу достаточно нажать <F6> во время самотестирования системы (POST) или войти в BIOS при помощи кнопки <F2> и выбрать пункт ASRock Instant Flash через меню. Запустите программу и сохраните новый BIOS на USB-флэшку, дискету или жесткий диск. После этого вы сможете оперативно обновить BIOS, без необходимости подготовки дополнительной дискеты, без установки программы прошивки. Имейте в виду, что USB­должны использовать файловую систему FAT32/16/12.
10. Если вы хотите быстрее и без ограничений заряжать свои устройства
Apple, например iPhone, iPod и iPad Touch, компания ASRock
приготовила отличное решение для вас – ASRock APP Charger. Просто установив драйвер APP Charger, вы сможете заряжать iPhone от компьютера намного быстрее, ускорение составит до 40%. ASRock APP Charger позволяет быстро заряжать несколько устройств Apple одновременно и даже поддерживает непрерывную зарядку,
компьютер переходит в режим ожидания (S1), режим ожидания с
сохранением данных в ОЗУ (S3), режим гибернации (S4) или режим выключения (S5). Установив драйвер APP Charger, вы испытаете небывалое удобство зарядки.
Веб-сайт ASRock: http://www.asrock.com/Feature/AppCharger/index.asp
11.
SmartView — это интеллектуальная стартовая страница для браузера IE, на которой отображаются наиболее посещаемые веб-сайты, история
посещений, друзья в Facebook и обновляемые потоки новостей. Эта новая функция обеспечивает более удобное использование возможностей Интернета. Системные платы ASRock эксклюзивно снабжаются программой SmartView, помогающей поддерживать связь с друзьями. Программа SmartView работает в ОС Windows
VistaTM / VistaTM 64 bit и браузере IE8. Веб-сайт ASRock: http://www.asrock.
com/Feature/SmartView/index.asp
12. Функция ASRock XFast USB увеличивает скорость работы устройств
USB. Рост скорости зависит от устройства.
13. ASRock XFast LAN обеспечивает более быстрый доступ к сети Интернет,
который даст описанные далее преимущества. Установка приоритетов приложений ЛВС: можно задать оптимальный приоритет для своего приложения и/или добавить новые программы. Более низкая латентность в игре: после установки более высокого онлайн, может снизиться латентность в игре. Формирование трафика: можно одновременно просматривать видео высокого разрешения на Youtube и загружать файлы. Анализ данных в реальном времени: в окне состояния можно легко определить, какие потоки данных передаются в данный момент времени.
флэшка или винчестер
приоритета игре в режиме
®
.
когда
®
7 / 7 64 bit /
94
ASRock Z68M/USB3 Motherboard
14. Благодаря технологии Lucid Virtu вы можете одновременно наслаждаться преимуществами 3D-производительности дискретного графического процессора и широкими мультимедийными возможностями HD­видеоадаптера Intel
15. Хотя данная материнская плата поддерживает плавную настройку частоты, устанавливать повышенную частоту не рекомендуется. Использование значений частоты шины процессора отличающихся от рекомендованных, может привести к нестабильной работе системы или повреждению процессора и материнской платы.
16. При обнаружении перегрева процессора работа системы автоматически завершается. Прежде чем возобновить работу системы, убедитесь в нормальной и отсоедините шнур питания, а затем снова подключите его. Чтобы улучшить отвод тепла, не забудьте при сборке компьютера нанести термопасту между процессором и радиатором.
17. Combo Cooler Option (C.C.O.) предоставляет возможность устанавливать разные типы процессорных кулеров на материнскую плату – под Socket LGA775, LGA1155 или LGA1156. Внимание, не все кулеры под LGA775 или LGA1156 можно использовать
18. EuP расшифровывается как Energy Using Product. Стандарт был разработан Европейским Союзом для определения энергопотребления готовых систем. По требованию EuP система в выключенном состоянии должна потреблять менее 1 Вт энергии. Для соответствия стандарту EuP нужны соответствующие материнская плата и блок питания. Компания Intel предложила, что совместимый с EuP блок питания должен обеспечивать 50% эффективность линии питания 5V при потреблении 100 мА (в блоков питания, чтобы выбрать модель с поддержкой EuP.
режиме ожидания). Сверьтесь с информацией производителей
®
.
работе вентилятора процессора на материнской плате
.
ASRock Z68M/USB3 Motherboard
Русский
95
1.3 Установка перемычек
Конфигурация перемычек иллюстрируется на рисунке. Когда перемычка надета на контакты, они называются “замкнутыми” (short). Если на контактах перемычки нет, то они называются “разомкнутыми” (open). На иллюстрации показана 3-контактная перемычка, у которой контакты 1 и 2 замкнуты.
Перемычка Установка Описание
Очистка CMOS
(CLRCMOS1, 3-контактная перемычка) (см. стр. 2, п. 9)
Стандартные Очистка CMOS
Русский
Примечание.
Контактная колодка CLRCMOS1 позволяет очистить данные CMOS. Для очистки данных и восстановления заводских системных параметров сначала выключите компьютер и отсоедините сетевую вилку кабеля питания от электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5 секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не производите очистку CMOS непосредственно после обновления BIOS. Если необходимо очистить CMOS сразу же после перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а затем завершить ее работу. Примите во внимание, что пароль, дата, время, профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес будут очищены только тогда, когда будет извлечена из своего гнезда батарейка
CMOS.
окончания обновления BIOS, то,
96
ASRock Z68M/USB3 Motherboard
1.4 Колодки и разъемы на плате
Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки на эти колодки и разъемы – это приведет к необратимому повреждению материнской платы!
Разъем дисковода гибких дисков
(33-контактный FLOPPY1)
(см. стр. 2, п. 25)
Примечание. Убедитесь, что сторона кабеля с красной полосой соответствует контакту 1 на разъеме.
Разъемы Serial ATAII четыре соединителя Serial ATAII
(SATA2_2, см. стр. 2, п. 13) (SATA2_3, см. стр. 2, п. 12) (SATA2_4, см. стр. 2, п. 14) (SATA2_5, см. стр. 2, п. 15)
кабелей SATAII. В настоящее
предназначаются для
SATA2_3 SATA2_2
подключения внутренних устройств хранения с
использованием интерфейсных
SATA2_5 SATA2_4
время интерфейс SATA допускает скорость передачи данных до \ 3,0 Гбит/с.
Разъемы Serial ATA3 Два соединителя Serial ATA3
(SATA3_0, см. стр. 2, п. 7) (SATA3_1, см. стр. 2, п. 8)
устройств хранения с
использованием нтерфейсных
кабелей SATA3. В настоящее
время интерфейс SATA
предназначаются для подключения внутренних
SATA3_0
SATA3_1
допускает скорость передачи данных до \ 6,0 Гбит/с.
la banda roja debe quedar en el mismo lado que el contacto 1
Информационный Информационный кабель кабель Serial ATA (SATA) интерфейса SATA / SATAII / SATA3
(дополнительно)
не является направленным. Любой из его соединителей может быть подключен либо к жесткому диску интерфейса SATAII / SATA3 либо к материнской плате.
ASRock Z68M/USB3 Motherboard
Русский
97
Колодка USB 2.0 Помимо четыре стандартных
(9-контактный USB6_7) (см. стр. 2, п. 22)
портов USB 2.0 на панели ввода-
вывода, на данной материнской плате предусмотрено три разъема USB 2.0. Каждый разъем USB 2.0 поддерживает два порта USB 2.0.
1
1
USB_PWR
P-9
P-8
USB_PWR
USB_PW R
P-11
P-10
USB_PW R
1
P+9
P+8
P+11
P+10
IRTX
IRRX
GND
GND
GND
GND
+5VSB
GND
DUMMY
DUMMY
DUMMY
(9-контактный USB8_9) (см. стр. 2, п. 20)
(9-контактный USB10_11) (см. стр. 2, п. 19)
Колодка инфракрасного модуля Данная колодка позволяет
(5-контактный IR1) (см. стр. 2, п. 6)
подключить дополнительный
модуль беспроводного инфракрасного приемопередатчика.
Датчик пользовательского инфракрасного модуля Датчик можно использовать для
(4-контактный CIR1) (см. стр. 2, п. 23)
устройств, например, устройств
подключения дополнительных
пользовательских инфракрасных
1
ATX+5VSB
IRRX
IRTX
GND
HI-FI, телевизоров и т.д.
Русский
Разъем порта печати Это интерфейс кабеля порта
(25-выводов LPT1) (см. cтр. 2, п.24)
подключение принтеров.
Аудиоразъем передней Этот интерфейс предназначен панели для присоединения
(9-контактный HD_AUDIO1) (см. cтр. 2, п.27)
обеспечивающего удобное подключение аудиоустройств и управление ими.
AFD#
печати, обеспечивающий удобное
ERROR#
PINIT#
SLIN#
1
SPD2
SPD1
SPD0
STB#
аудиокабеля передней панели,
SPD3
1
SPD4
SPD6
SPD5
GND
PRESENCE#
MIC2_R
MIC2_L
GND
SPD7
MIC_RET
J_SENSE
OUT2_R
ACK#
BUSY
OUT_RET
OUT2_L
PE
SLCT
98
ASRock Z68M/USB3 Motherboard
1. Система High Defi nition Audio поддерживает функцию автоматического обнаружения разъемов (Jack Sensing), однако для ее правильной pаботы кабель панели в корпусе должен поддерживать HDA. При сборке системы следуйте инструкциям, приведенным в нашем руководстве и руководстве пользователя для корпуса.
2. Если вы используете аудиопанель AC’97, подключите ее к колодке аудиоинтерфейса передней панели следующим образом: A. Подключите B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а выводы Audio_L (LIN) к контактам OUT2_L. C. Подключите выводы Ground (GND) к контактам Ground (GND).
D. Контакты MIC_RET и OUT_RET предназначены только для аудиопанели HD. При использовании аудиопанели AC’97
подключать их не нужно.
E. Процедура активации микрофона приведена ниже. Для ОС Windows Выберите «Mixer» (Микшер). Выберите «Recorder» (Устройство записи). Затем щелкните «FrontMic» (Передний микрофон). Для ОС Windows® 7 / 7 64-бита, VistaTM / VistaTM 64-бита: Перейдите к вкладке «FrontMic» (Передний микрофон) в панели управления Realtek. Отрегулируйте уровень «Recording Volume» (Громкость записи).
Колодка системной панели Данная колодка обеспечивает
(9-контактный PANEL1) (см. стр. 2, п. 18)
работу нескольких функций
передней панели системы.
выводы Mic_IN (MIC) к контактам MIC2_L.
®
XP / XP 64-бита:
Подключите к этому разъему кнопку питания, кнопку сброса и индикатор состояния системы на корпусе в соответствии с указанным ниже назначением контактов. При подключении кабелей необходимо соблюдать полярность положительных и отрицательных контактов.
PWRBTN (кнопка питания):
Подключите к этим контактам кнопку питания на передней панели корпуса. Способ выключения системы с можно настроить.
RESET (кнопка сброса):
Подключите к этим контактам кнопку сброса на передней панели корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если компьютер «завис» и нормальную перезагрузку выполнить не удается.
помощью кнопки питания
ASRock Z68M/USB3 Motherboard
Русский
99
PLED (индикатор питания системы):
Подключите к этим контактам индикатор состояния питания на передней панели корпуса. Этот индикатор светится, когда система работает. Индикатор мигает, когда система находится в режиме ожидания S1. Этот индикатор не светится, когда система находится в режиме ожидания S3 или S4, либо выключена (S5).
HDLED (индикатор активности жесткого диска):
Подключите к
этим контактам индикатор активности жесткого диска на передней панели корпуса. Этот индикатор светится, когда осуществляется считывание или запись данных на жестком диске.
Конструкция передней панели может различаться в зависимости от корпуса. Модуль передней панели в основном состоит из кнопки питания, кнопки сброса, индикатора питания, индикатора активности жесткого
диска, динамика и т.п. При подключении к этому разъему модуля передней панели корпуса удостоверьтесь, что провода подключаются к соответствующим контактам.
Колодка динамика корпуса Подключите к этой колодке
(4-контактный SPEAKER1) (см. стр. 2, п. 21)
кабель от динамика на корпусе
компьютера.
разъем Power LED Подключите индикатор Power LED
(3-контактный PLED1) (см. стр. 2, п. 16)
светодиод продолжит мигать в
к этому разъему для отображения
статуса питания системы. Этот
1
PLED+
PLED+
PLED-
режиме S1. Светодиод будет выключен в режимах S3/S4 или S5 (система выключена).
Chassis и Power Fan-соединители
(3-контактный CHA_FAN1) (см. стр. 2, п. 17)
(3-контактный PWR_FAN1) (см. стр. 2, п. 33)
PWR_FAN_SPEED
GND +12V CHA_FAN_SPEED
+12V
GND
Подключите кабели вентилятора к соединителям и присоедините черный шнур к штырю заземления.
Русский
Разъем вентилятора Подключите к этому разъему процессора кабель вентилятора процессора
(4-контактный CPU_FAN1) (см. стр. 2, п. 1)
соответствовал контакту земли.
так, чтобы черный провод
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
100
ASRock Z68M/USB3 Motherboard
Loading...