ASROCK FM2A85X Extreme 4 User Manual [fr]

Page 1
Copyright Notice:
No part of this installation guide may be reproduced, transcribed, transmitted, or trans­lated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered trademarks or copyrights of their respective companies, and are used only for identifi ca- tion or explanation and to the owners’ benefi t, without intent to infringe.
Disclaimer:
Specifi cations and information contained in this guide are furnished for informational use only and subject to change without notice, and should not be constructed as a commit­ment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or condi­tions of merchantability or fi tness for a particular purpose. In no event shall ASRock, its directors, offi cers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profi ts, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the pos­sibility of such damages arising from any defect or error in the guide or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
Published October 2012
Copyright©2012 ASRock INC. All rights reserved.
ASRock FM2A85X Extreme4 Motherboard

English

1
Page 2
Motherboard Layout
3
2
1
Keyboard/
Mouse
Ps2
USB3.0 T:US B1 B:USB2
PWR_FAN1
Top:
Top:
X
PCIE1
DX11
PCIE3
ErP/EuP Ready
HDMI_SPDIF1
1
ATX12V1
FastLAN
CHA_FAN3
CHA_FAN2
FM2A85X Extreme4
Dual Graphics
PCIE2
CMOS
BATTERY
PCI1
X
FastUSB
PCIE4
PCI2
RoHS
PCI3
USB3_4
COM1
1
1
1
CIR1
DVI1
VGA1
HDMI1
USB3.0 T:USB3 B:USB4
Clr
CMOS
eSATA1
USB2.0 T:USB1 B:USB2
USB3.0
Top:
T: US B5
RJ-45
B:USB6
CTR BASS
Center:
REAR SPK
Bottom:
Optical
SPDIF
Bottom:
MIC IN
LINE IN
Center:
FRONT
44
43
42
41
40
39
38
37
36
35
LAN
Super
I/O
AUDIO
CODEC
HD_AUDIO1
1
6
7
DDR3 2600+
FastRAM
X
DDR3_A1(64 bit, 240-pinmodule)
DDR3_A2(64 bit, 240-pinmodule)
8
DDR3_B1(64 bit, 240-pinmodule)
DDR3_B2(64 bit, 240-pinmodule)
USB3_7_8
9
ATXPWR1
10
5
4
CPU_FAN2
CPU_FAN1
SOCKET FM2
Front USB3.0
AMD A85X
(Hudson-D4)
CLRCMOS1
Chipset
1
64Mb BIOS
USB7_8
USB5_6
1
1
SATA3_2
SATA3_4
SATA3_7
Dr.
Debug
SATA3_5
SPEAKER1
PLED1
1
1
PWRBTN
CHA_FAN1
IR1
PLEDPWRBTN
1
1
HDLED RESET
11
12 13
SATA3_1
14
SATA3_3
15 16
SATA3_6
17 18
19
RSTBTN
20
21
PANEL1
English
33
34
32
29
3031
23
22
25262728
24
1 Power Fan Connector (PWR_FAN1) 22 Power Switch (PWRBTN) 2 ATX 12V Power Connector (ATX12V1) 23 Chassis Speaker Header (SPEAKER1) 3 CPU Heatsink Retention Module 24 Chassis Fan Connector (CHA_FAN1) 4 CPU Socket 25 Infrared Module Header (IR1) 5 CPU Fan Connector (CPU_FAN1) 26 Power LED Header (PLED1) 6 CPU Fan Connector (CPU_FAN2) 27 Clear CMOS Jumper (CLRCMOS1) 7 2 x 240-pin DDR3 DIMM Slots 28 USB 2.0 Header (USB7_8) (Dual Channel A: DDR3_A1, DDR3_B1) 29 USB 2.0 Header (USB5_6) 8 2 x 240-pin DDR3 DIMM Slots 30 USB 2.0 Header (USB3_4) (Dual Channel B: DDR3_A2, DDR3_B2) 31 Consumer Infrared Module Header (CIR1) 9 ATX Power Connector (ATXPWR1) 32 COM Port Header (COM1) 10 USB 3.0 Header (USB3_7_8) 33 HDMI_SPDIF Header (HDMI_SPDIF1) 11 Southbridge Controller 34 Front Panel Audio Header (HD_AUDIO1) 12 SATA3 Connector (SATA3_2) 35 PCI Slot (PCI3) 13 SATA3 Connector (SATA3_1) 36 PCI Slot (PCI2) 14 SATA3 Connector (SATA3_3) 37 SPI Flash Memory (64Mb) 15 SATA3 Connector (SATA3_4) 38 PCI Express 2.0 x16 Slot (PCIE4) 16 SATA3 Connector (SATA3_6) 39 PCI Slot (PCI1) 17 SATA3 Connector (SATA3_7) 40 PCI Express 2.0 x1 Slot (PCIE3) 18 Dr. Debug (LED) 41 PCI Express 2.0 x16 Slot (PCIE2) 19 SATA3 Connector (SATA3_5) 42 PCI Express 2.0 x1 Slot (PCIE1) 20 Reset Switch (RSTBTN) 43 Chassis Fan Connector (CHA_FAN2) 21 System Panel Header (PANEL1) 44 Chassis Fan Connector (CHA_FAN3)
2
ASRock FM2A85X Extreme4 Motherboard
Page 3
I/O Panel
5
4
9
6
10
7
11
8
12
ACT/LINK LED
SPEED LED
15
3
13
14
1
17
1 PS/2 Mouse/Keyboard Port (Green/Purple) *** 10 Front Speaker (Lime) 2 D-Sub Port (VGA1) 11 Microphone (Pink) 3 USB 3.0 Ports (USB34) 12 USB 3.0 Ports (USB56) * 4 USB 2.0 Ports (USB01) **** 13 eSATA3 Connector (eSATA1) ** 5 LAN RJ-45 Port 14 Clear CMOS Switch (CLRCBTN) 6 Central / Bass (Orange) 15 HDMI Port (HDMI1) 7 Rear Speaker (Black) 16 DVI-D Port (DVI1) 8 Optical SPDIF Out Port 17 USB 3.0 Ports (USB12) 9 Line In (Light Blue)
* It is recommended to install the USB Keyboard/Mouse cable to USB 2.0 ports (USB01) instead of USB 3.0 ports.
** There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.
Activity/Link LED SPEED LED
Status Description Status Description
2
16
LAN Port LED Indications
Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
LAN Port
If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”.
***
See the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker Central / Bass Line In or (No. 10) (No. 7) (No. 6) Side Speaker (No. 9)
2 V -- -- -­4 V V -- -­6 V V V -­8 V V V V
3
ASRock FM2A85X Extreme4 Motherboard
English
Page 4
To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. After restarting your computer, you will fi nd “Mixer” tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”.
Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Pri­mary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.
**** eSATA3 connector supports SATA Gen3 in cable 1M.
English
4
ASRock FM2A85X Extreme4 Motherboard
Page 5
1. Introduction
Thank you for purchasing ASRock FM2A85X Extreme4 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commit­ment to quality and endurance. This Quick Installation Guide contains introduction of the motherboard and step-by­step installation guide. More detailed information of the motherboard can be found in the user manual presented in the Support CD.
Because the motherboard specifi cations and the BIOS software might be updated, the content of this manual will be subject to change without no­tice. In case any modifi cations of this manual occur, the updated version will be available on ASRock website without further notice. You may fi nd the latest VGA cards and CPU support lists on ASRock website as well. ASRock website http://www.asrock.com If you require technical support related to this motherboard, please visit our website for specifi c information about the model you are using. www.asrock.com/support/index.asp
1.1 Package Contents
ASRock FM2A85X Extreme4 Motherboard (ATX Form Factor) ASRock FM2A85X Extreme4 Quick Installation Guide ASRock FM2A85X Extreme4 Support CD 4 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield
ASRock Reminds You...
To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista VistaTM 64-bit, it is recommended to set the BIOS option in Storage Con­ guration to AHCI mode. For the BIOS setup, please refer to the “User Manual” in our support CD for details.
TM
ASRock FM2A85X Extreme4 Motherboard
/
English
5
Page 6
English
1.2 Specifi cations
Platform - ATX Form Factor
- ASRock DuraCap (2.5 x longer life time) (100% Japan-made high-quality Conductive Polymer Capacitors) CPU - Support for Socket FM2 100W processors
- 4 + 2 Power Phase Design
- Supports AMD’s Cool ‘n’ QuietTM Technology
- UMI-Link GEN2
Chipset - AMD A85X (Hudson-D4) Memory - Dual Channel DDR3 Memory Technology
- 4 x DDR3 DIMM slots
- Support DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/ 1333/1066/800 non-ECC, un-buffered memory (see CAUTION 1) * 2600+ is only supported with two DIMMs
- Max. capacity of system memory: 64GB (see CAUTION 2)
- Supports Intel
- Supports AMD Memory Profi le (AMP) Expansion Slot - 2 x PCI Express 2.0 x16 slots (PCIE2 @ x16 mode; PCIE4 @ x4 mode)
- 2 x PCI Express 2.0 x1 slots
- 3 x PCI slots
- Supports AMD Quad CrossFireX Graphics Graphics - AMD Radeon HD 7000 graphics
- DirectX 11, Pixel Shader 5.0
- Max. shared memory 2GB
- Three VGA Output options: D-Sub, DVI-D and HDMI
- Supports HDMI 1.4a Technology with max. resolution up to 1920x1200 @ 60Hz
- Supports Dual-link DVI with max. resolution up to 2560x1600 @ 75Hz
- Supports D-Sub with max. resolution up to 1920x1600 @ 60Hz
- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI (Compliant HDMI monitor is required) (see CAUTION 3)
- Supports Blu-ray Stereoscopic 3D with HDMI 1.4a
- Supports AMD Steady Video processing capability for automatic jutter reduction on home/
®
Extreme Memory Profi le (XMP) 1.3 / 1.2
TM
, CrossFireXTM and Dual
TM
2.0: New video post
6
ASRock FM2A85X Extreme4 Motherboard
Page 7
online video
- Supports HDCP function with DVI and HDMI ports
- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with DVI and HDMI ports Audio - 7.1 CH HD Audio with Content Protection (Realtek ALC892 Audio Codec)
- Premium Blu-ray audio support
- Supports THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supports Wake-On-LAN
- Supports LAN Cable Detection
- Supports Energy Effi cient Ethernet 802.3az
- Supports PXE Rear Panel I/O I/O Panel
- 1 x PS/2 Mouse/Keyboard Port
- 1 x D-Sub Port
- 1 x DVI-D Port
- 1 x HDMI Port
- 1 x Optical SPDIF Out Port
- 2 x Ready-to-Use USB 2.0 Ports
- 1 x eSATA3 Connector
- 6 x Ready-to-Use USB 3.0 Ports
- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
- 1 x Clear CMOS Switch with LED
- HD Audio Jack: Rear Speaker/Central/Bass/Line in/Front Speaker/Microphone SATA 3 - 7 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 5 and RAID 10), NCQ, AHCI and “Hot Plug” functions USB 3.0 - 2 x Rear USB 3.0 ports by AMD A85X (Hudson-D4), support USB 1.1/2.0/3.0 up to 5Gb/s
- 4 x Rear USB 3.0 ports by Etron EJ188, support USB 1.1/2.0/3.0 up to 5Gb/s
- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports) by AMD A85X (Hudson-D4), supports USB 1.1/2.0/3.0 up to 5Gb/s Connector - 7 x SATA3 6.0Gb/s connectors
- 1 x IR header
- 1 x CIR header
- 1 x COM port header
ASRock FM2A85X Extreme4 Motherboard
English
7
Page 8
English
- 1 x HDMI_SPDIF header
- 1 x Power LED header
- 2 x CPU Fan connectors (1 x 4-pin, 1 x 3-pin)
- 3 x Chassis Fan connectors (1 x 4-pin, 2 x 3-pin)
- 1 x Power Fan connector (3-pin)
- 24 pin ATX power connector
- 8 pin 12V power connector
- Front panel audio connector
- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
- 1 x USB 3.0 header (supports 2 USB 3.0 ports)
- 1 x Dr. Debug (7-Segment Debug LED)
- 1 x Power Switch with LED
- 1 x Reset Switch with LED BIOS Feature - 64Mb AMI UEFI Legal BIOS with GUI support
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
- DRAM, APU PCIE VDDP, CPU and CPU NB/GFX Voltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser and Toolbar Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing
- CPU/Chassis/Power Fan Tachometer
- CPU Quiet Fan
- CPU/Chassis Fan Multi-Speed Control
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore OS - Microsoft Vista
TM
64-bit compliant
®
Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista
TM
/
Certi cations - FCC, CE, WHQL
- ErP/EuP Ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com
8
ASRock FM2A85X Extreme4 Motherboard
Page 9
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
CAUTION!
1. Whether 2600/2400/2133/1866/1600MHz memory speed is supported depends on the CPU you adopt. If you want to adopt DDR3 2600/2400/2133/1866/1600 memory module on this motherboard, please refer to the memory support list on our website for the compatible memory modules.
ASRock website http://www.asrock.com
2. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage un­der Windows bit CPU, there is no such limitation.
RAM to utilize the memory that Windows® cannot use.
3. xvYCC and Deep Color are only supported under Windows® 8 64-bit / 8 / 7 64-bit / 7. Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows
®
8 / 7 / VistaTM. For Windows® 64-bit OS with 64-
You can use ASRock XFast
®
8 64-bit / 8 / 7 64-bit / 7 / VistaTM 64-bit / VistaTM.
ASRock FM2A85X Extreme4 Motherboard
English
9
Page 10
1.3 Unique Features
ASRock Extreme Tuning Utility (AXTU)
ASRock Extreme Tuning Utility (AXTU) is an all-in-one tool to
ne-tune different system functions in a user-friendly interface, which includes Hardware Monitor, Fan Control, Overclocking, OC DNA, IES and XFast RAM. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a profi le and share it with your friends. Your friends then can load the OC profi le to their own system to get the same OC set- tings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of output phases to improve effi ciency when the CPU cores are idle without sacrifi cing computing per- formance. In
cannot be used under Windows® OS 32-bit CPU.
ASRock Instant Boot
ASRock Instant Boot allows you to turn on your PC in just a few
seconds, provides a much more effi cient way to save energy, time, money, and improves system running speed for your sys­tem. It leverages the S3 and S4 ACPI features which normally enable the Sleep/Standby and Hibernation modes in Windows to shorten boot up time. By calling S3 and S4 at specifi c timing during the shutdown and startup process, Instant Boot allows you to enter your Windows
XFast RAM, it fully utilizes the memory space that
®
desktop in a few seconds.
®
English
10
ASRock Instant Flash
ASRock Instant Flash is a BIOS fl ash utility embedded in Flash
ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating systems fi rst like MS- DOS or Windows
®
. With this utility, you can press the <F6> key during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS fi le to your USB fl ash drive, fl oppy disk or hard drive, then you can update your BIOS only in a few clicks without preparing an additional fl oppy diskette or other compli- cated fl ash utility. Please be noted that the USB fl ash drive or hard drive must use FAT32/16/12 fi le system.
ASRock FM2A85X Extreme4 Motherboard
Page 11
ASRock APP Charger
If you desire a faster, less restricted way of charging your
Apple devices, such as iPhone/iPad/iPod Touch, ASRock has prepared a wonderful solution for you - ASRock APP Charger. Simply install the APP Charger driver, it makes your iPhone charge much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continu­ous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the mar­velous charging experience.
ASRock XFast USB
ASRock XFast USB can boost USB storage device perfor-
mance. The performance may depend on the properties of the device.
ASRock XFast LAN
ASRock XFast LAN provides a faster internet access, which
includes the benefits listed below. LAN Application Prioritiza­tion: You can confi gure your application’s priority ideally and/or add new programs. Lower Latency in Game: After setting online game’s priority higher, it can lower the latency in games. Traffi c Shaping: You can watch Youtube HD videos and download si­multaneously. Real-Time Analysis of Your Data: With the status window, you can easily recognize which data streams you are transferring currently.
ASRock XFast RAM
ASRock XFast RAM is a new function that is included into AS­Rock Extreme Tuning Utility (AXTU). It fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU. ASRock XFast RAM shortens the loading time of previously visited websites, making web surfing faster than ever. And it also boosts the speed of Adobe Photoshop 5 times faster. An­other advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.
ASRock FM2A85X Extreme4 Motherboard
English
11
Page 12
ASRock Crashless BIOS
ASRock Crashless BIOS allows users to update their BIOS
without fear of failing. If power loss occurs during the BIOS up­date process, ASRock Crashless BIOS will automatically fi nish the BIOS update procedure after regaining power. Please note that BIOS fi les need to be placed in the root directory of your USB disk. Only USB2.0 ports support this feature.
ASRock OMG (Online Management Guard)
Administrators are able to establish an internet curfew or restrict
internet access at specifi ed times via OMG. You may schedule the starting and ending hours of internet access granted to other users. In order to prevent users from bypassing OMG, guest accounts without permission to modify the system time are re­quired.
ASRock Internet Flash
ASRock Internet Flash searches for available UEFI firmware
updates from our servers. In other words, the system can auto­detect the latest UEFI from our servers and fl ash them without entering Windows
®
OS. Please note that you must be running
on a DHCP confi gured computer in order to enable this function.
ASRock UEFI System Browser
ASRock UEFI system browser is a useful tool included in
graphical UEFI. It can detect the devices and configurations that users are currently using in their PC. With the UEFI system browser, you can easily examine the current system confi gura- tion in UEFI setup.
English
ASRock On/Off Play Technology
ASRock On/Off Play Technology allows users to enjoy the great
audio experience from the portable audio devices, such like MP3 player or mobile phone to your PC, even when the PC is turned off (or in ACPI S5 mode)! This motherboard also provides a free 3.5mm audio cable (optional) that ensures users the most convenient computing environment.
12
ASRock FM2A85X Extreme4 Motherboard
Page 13
ASRock Dehumidifi er Function
Users may prevent motherboard damages due to dampness by
enabling “Dehumidifi er Function”. When enabling Dehumidifi er Function, the computer will power on automatically to dehumidi­fy the system after entering S4/S5 state.
ASRock Easy RAID Installer
ASRock Easy RAID Installer can help you to copy the RAID
driver from a support CD to your USB storage device. After copying the RAID driver to your USB storage device, please change “SATA Mode” to “RAID”, then you can start installing the OS in RAID mode.
ASRock Interactive UEFI
ASRock Interactive UEFI is a blend of system configuration
tools, cool sound effects and stunning visuals. The unprec­edented UEFI provides a more attractive interface and brings a lot more amusing.
ASRock Fast Boot
With ASRock’s exclusive Fast Boot technology, it takes less
than 1.5 seconds to logon to Windows
®
8 from a cold boot. No more waiting! The speedy boot will completely change your user experience and behavior.
ASRock X-Boost
Brilliantly designed for combo overclocking, ASRock X-Boost
Technology is able to unleash the hidden power of your CPUs. Simply press “X” when turning on the PC, X-Boost will automati­cally overclock the relative components to get up to 15.77% performance boost! With the smart X-Boost, overclocking CPU can become a near one-button process.
ASRock Restart to UEFI
Windows
®
8 brings the ultimate boot up experience. The light­ning boot up speed makes it hard to access the UEFI setup. AS­Rock Restart to UEFI technology is designed for those requiring frequent UEFI access. It allows users to easily enter the UEFI automatically when turning on the PC next time. Just simply enable this function; the PC will be assured to access the UEFI directly in the very beginning.
ASRock FM2A85X Extreme4 Motherboard
English
13
Page 14
Lucid Virtu Universal MVP
VIRTU Universal MVP includes the base features of Virtu
Universal technology, which virtualizes integrated GPU and discrete GPU for best of breed functionality. It also features Vir­tual Vsync™ for no-compromise visual quality. With the added benefi ts of HyperFormance technology, VIRTU Universal MVP improves game performance by intelligently reducing redundant rendering tasks in the fl ow between the CPU, GPU and the dis- play.
English
14
ASRock FM2A85X Extreme4 Motherboard
Page 15
2. Installation
This is an ATX form factor motherboard. Before you install the motherboard, study the confi guration of your chassis to ensure that the motherboard fi ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Before you install or remove any component, ensure that the power is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static elec­tricity, NEVER place your motherboard directly on the carpet or the like. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti­static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the mother­board to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.
ASRock FM2A85X Extreme4 Motherboard
English
15
Page 16
2.1 CPU Installation
Step 1. Unlock the socket by lifting the lever up to a 90
o
angle. Step 2. Position the CPU directly above the socket such that the CPU corner with the golden triangle matches the socket corner with a small triangle. Step 3. Carefully insert the CPU into the socket until it fi ts in place.
The CPU fi ts only in one correct orientation. DO NOT force the CPU into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it fi rmly on the socket while you push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.
Lever 90° Up
CPU Golden Triangle
STEP 1: Lift Up The Socket Lever
STEP 2 / STEP 3: Match The CPU Golden Triangle To The Socket Corner Small Triangle
Socket Corner Small Triangle
STEP 4: Push Down And Lock The Socket Lever
2.2 Installation of CPU Fan and Heatsink
English
After you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dis­sipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU FAN connector (CPU_FAN1, see Page 2, No. 5 or CPU_FAN2, see Page 2, No. 6). For proper installation, please kindly refer to the instruc­tion manuals of the CPU fan and the heatsink.
16
ASRock FM2A85X Extreme4 Motherboard
Page 17
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel con­ guration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pair in the slots of the same color. In other words, you have to install identical DDR3 DIMM pair in Dual Channel A (DDR3_A1 and DDR3_B1; see p.2 No.7) or identical DDR3 DIMM pair in Dual Channel B (DDR3_A2 and DDR3_B2; see p.2 No.8), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDR3 DIMMs for dual channel confi guration, and please install identical DDR3 DIMMs in all four slots. You may refer to the Dual Channel Memory Confi gura- tion Table below.
Dual Channel Memory Confi gurations
DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2 (1) Populated - Populated ­(2) - Populated - Populated (3)* Populated Populated Populated Populated
For the confi guration (3), please install identical DDR3 DIMMs in all four
*
slots.
1. If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in the slots: DDR3_ A1 and DDR3_B1, or DDR3_A2 and DDR3_B2.
2. If only one memory module or three memory modules are installed in the DDR3 DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual Channel, for example, installing a pair of memory modules in DDR3_A1 and DDR3_A2, it is unable to activate the Dual Channel Memory Technology .
4. It is not allowed to install a DDR or DDR2 memory module into DDR3 slot; otherwise, this motherboard and DIMM may be dam­aged.
5. If you adopt DDR3 2600/2400/2133/1866/1600 memory modules on this motherboard, it is recommended to install them on DDR3_ A2 and DDR3_B2 slots.
English
ASRock FM2A85X Extreme4 Motherboard
17
Page 18
Installing a DIMM
Please make sure to disconnect power supply before adding or removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.
notch break
notch
break
The DIMM only fi ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
English
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.
18
ASRock FM2A85X Extreme4 Motherboard
Page 19
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 3 PCI slots and 4 PCI Express slots on this motherboard. PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI interface.
PCIE Slots:
PCIE1 / PCIE3 (PCIE x1 slot) is used for PCI Express cards with x1
lane width cards, such as Gigabit LAN card and SATA2 card.
PCIE2 (PCIE x16 slot) is used for PCI Express x16 lane width graphics
cards, or used to install PCI Express graphics cards to support CrossFi-
TM
reX
function.
PCIE4 (PCIE x16 slot) is used for PCI Express x4 lane width cards,
or used to install PCI Express graphics cards to support CrossFireX function.
1. In single VGA card mode, it is recommended to install a PCI Ex­press x16 graphics card on PCIE2 slot.
2. In CrossFireXTM mode, please install PCI Express x16 graphics cards on PCIE2 and PCIE4 slots.
3. Please connect a chassis fan to motherboard chassis fan connec­tor (CHA_FAN1, CHA_FAN2 or CHA_FAN3) when using multiple graphics cards for better thermal environment.
TM
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis). Step 3. Remove the bracket facing the slot that you intend to use. Keep the
screws for later use. Step 4. Align the card connector with the slot and press fi rmly until the card is
completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.
ASRock FM2A85X Extreme4 Motherboard
English
19
Page 20
2.5 CrossFireXTM and Quad CrossFireXTM Operation Guide
This motherboard supports CrossFireXTM and Quad CrossFireXTM feature. CrossFireXTM technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units (GPU) in a single PC. Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism, CrossFireX
TM
enables the highest possible level of performance and image quality in any 3D application. Please check AMD website for AMD CrossFireXTM driver updates.
1. If a customer incorrectly configures their system they will not see the performance benefi ts of CrossFireXTM. All three CrossFireXTM components, a CrossFireXTM Ready graphics card, a CrossFireXTM Ready motherboard and a CrossFireXTM Edition co-processor graphics card, must be installed correctly to benefi t from the CrossFireX
2. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both cards will operate as 12-pipe cards while in CrossFireXTM mode.
TM
multi-GPU platform.
2.5.1 Graphics Card Setup
Different CrossFireXTM cards may require different methods to enable CrossFi-
reXTM feature. For other CrossFireXTM cards that AMD has released or will release in the future, please refer to AMD graphics card manuals for detailed installation guide.
English
Step 1. Insert one Radeon graphics card into PCIE2 slot and the other Radeon
graphics card to PCIE4 slot. Make sure that the cards are properly seated on the slots.
20
ASRock FM2A85X Extreme4 Motherboard
Page 21
Step 2. Connect two Radeon graphics cards by installing CrossFire Bridge on
CrossFire Bridge Interconnects on the top of Radeon graphics cards. (CrossFire Bridge is provided with the graphics card you purchase, not bundled with this motherboard. Please refer to your graphics card vendor for details.)
CrossFire Bridge
or
Step 3. Connect the DVI monitor cable to the DVI connector on the Radeon graph-
ics card on PCIE2 slot. (You may use the DVI to D-Sub adapter to convert the DVI connector to D-Sub interface, and then connect the D-Sub monitor cable to the DVI to D-Sub adapter.)
ASRock FM2A85X Extreme4 Motherboard
English
21
Page 22
2.5.2 Driver Installation and Setup
Step 1. Power on your computer and boot into OS. Step 2. Remove the AMD driver if you have any VGA driver installed in your sys-
tem.
The Catalyst Uninstaller is an optional download. We recommend using this
utility to uninstall any previously installed Catalyst drivers prior to installation.
Please check AMD website for AMD driver updates.
Step 3. Install the required drivers to your system.
For Windows
®
8 / 7 / VistaTM OS:
Install the CATALYST Control Center. Please check AMD website for de-
tails. Step 4. Restart your computer. Step 5. Install the VGA card drivers to your system, and restart your computer. Then you will fi nd “ATI Catalyst Control Center” on your Windows
ATI Catalyst Control Center
®
taskbar.
Step 6. Double-click “ATI Catalyst Control Center”. Click “View”, select “CrossFi-
reXTM”, and then check the item “Enable CrossFireXTM”. Select “2 GPUs”
and click “Apply” (if you install two Radeon graphics cards).
English
22
ASRock FM2A85X Extreme4 Motherboard
Page 23
Although you have selected the option “Enable CrossFireTM”, the Cross-
TM
FireX
function may not work actually. Your computer will automatically reboot. After restarting your computer, please confi rm whether the option “Enable CrossFireTM” in “ATI Catalyst Control Center” is selected or not; if not, please select it again, and then you are able to enjoy the benefi t of CrossFireX
TM
feature.
Step 7. You can freely enjoy the benefi t of CrossFireXTM or Quad CrossFireXTM
feature.
* CrossFireXTM appearing here is a registered trademark of AMD Technologies Inc., and is used only for identifi cation or explanation and to the owners’ benefi t, without intent to infringe. * For further information of AMD CrossFireXTM technology, please check AMD website for updates and details.
ASRock FM2A85X Extreme4 Motherboard
English
23
Page 24
2.6 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.
Jumper Setting Description
Clear CMOS Jumper
(CLRCMOS1) (see p.2, No. 27)
Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug
the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just fi nish updating the BIOS, you must boot up the system fi rst, and then shut it down before you do the clear-CMOS ac- tion. Please be noted that the password, date, time, user default profi le, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed.
The Clear CMOS Switch has the same function as the Clear CMOS
jumper.
Clear CMOSDefault
English
24
ASRock FM2A85X Extreme4 Motherboard
Page 25
2.7 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard!
Serial ATA3 Connectors These seven Serial ATA3
(SATA3_1: see p.2, No. 13)
(SATA3_2: see p.2, No. 12)
(SATA3_3: see p.2, No. 14)
(SATA3_4: see p.2, No. 15)
(SATA3_5: see p.2, No. 19)
(SATA3_6: see p.2, No. 16)
(SATA3_7: see p.2, No. 17)
Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the
(Optional)
SATA3 hard disk or the SATA3
connector on this motherboard.
(SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to
6.0 Gb/s data transfer rate.
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
USB 2.0 Headers Besides two default USB 2.0
(9-pin USB3_4)
(see p.2 No. 30)
ports on the I/O panel, there
are three USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB
2.0 ports.
(9-pin USB5_6) (see p.2 No. 29)
(9-pin USB7_8) (see p.2 No. 28)
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-3
P-6
P+6
GND
DUMMY
GND
P+5
P-5
P-8
P+8
GND
DUMMY
GND
P+7
P-7
ASRock FM2A85X Extreme4 Motherboard
English
25
Page 26
USB 3.0 Header Besides six default USB 3.0
(19-pin USB3_7_8)
(see p.2, No. 10)
ports on the I/O panel, there is
one USB 3.0 header on this motherboard. This USB 3.0 header can support two USB 3.0 ports.
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
English
Infrared Module Header This header supports an
(5-pin IR1)
optional wireless transmitting
(see p.2 No. 25)
and receiving infrared module.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Consumer Infrared Module Header This header can be used to
(4-pin CIR1)
(see p.2 No. 31)
Front Panel Audio Header This is an interface for the front
(9-pin HD_AUDIO1)
(see p.2 No. 34)
control of audio devices.
connect the remote
controller receiver.
GND
PRESENCE#
panel audio cable that allows
convenient connection and
1. High Defi nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio header as below:
A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. To activate the front mic. For Windows Go to the “FrontMic” Tab in the Realtek Control panel. Adjust
“Recording Volume”.
MIC_RET
OUT_RET
1
®
8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
26
ASRock FM2A85X Extreme4 Motherboard
Page 27
System Panel Header This header accommodates
(9-pin PANEL1)
(see p.2 No. 21)
several system front panel
functions.
Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Switch):
Connect to the power switch on the chassis front panel. You may con­ gure the way to turn off your system using the power switch.
RESET (Reset Switch):
Connect to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to per­form a normal restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED keeps blinking when the sys-tem is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly.
Chassis Speaker Header Please connect the chassis
(4-pin SPEAKER 1)
(see p.2 No. 23)
Power LED Header Please connect the chassis
(3-pin PLED1)
(see p.2 No. 26)
speaker to this header.
power LED to this header to
indicate system power status.
1
PLED+
PLED+
PLED-
The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/S4 state or S5 state (power off).
ASRock FM2A85X Extreme4 Motherboard
English
27
Page 28
Chassis and Power Fan Connectors Please connect the fan cables
(4-pin CHA_FAN1)
(see p.2 No. 24)
to the fan connectors and
match the black wire to the
ground pin. CHA_FAN1/2/3 fan
(3-pin CHA_FAN2)
(see p.2 No. 43)
(3-pin CHA_FAN3) (see p.2 No. 44)
(3-pin PWR_FAN1) (see p.2 No. 1)
speed can be controlled through UEFI or AXTU.
English
CPU Fan Connectors Please connect the CPU fan
(4-pin CPU_FAN1)
(see p.2 No. 5)
cable to the connector and
match the black wire to the
ground pin.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
(3-pin CPU_FAN2)
(see p.2 No. 6)
ATX Power Connector Please connect an ATX power
(24-pin ATXPWR1)
(see p.2 No. 9)
Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply.
GND
+12V
12
CPU_FAN_SPEED
24
supply to this connector.
1
13
12
To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.
24
28
20-Pin ATX Power Supply Installation
ASRock FM2A85X Extreme4 Motherboard
1
13
Page 29
ATX 12V Power Connector Please connect an ATX 12V
(8-pin ATX12V1)
(see p.2 No. 2)
power supply to this connector.
4 8
1 5
Though this motherboard provides 8-pin ATX 12V power connector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use the 4-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 5.
4-Pin ATX 12V Power Supply Installation
4 8
1 5
Serial port Header This COM1 header supports a
(9-pin COM1)
(see p.2 No. 32)
serial port module.
HDMI_SPDIF Header HDMI_SPDIF header, providing
(2-pin HDMI_SPDIF1)
see p.2 No. 33)
(
SPDIF audio output to HDMI
VGA card, allows the system to connect HDMI Digital TV/ projector/LCD devices. Please connect the HDMI_SPDIF connector of HDMI VGA card to this header.
ASRock FM2A85X Extreme4 Motherboard
English
29
Page 30
2.8 Smart Switches
This motherboard has three smart switches: power switch, reset switch and clear CMOS switch, allowing users to quickly turn on/off or reset the system or clear the CMOS values.
Power Switch Power Switch is a smart switch,
(PWRBTN)
(see p.2 No. 22)
Reset Switch Reset Switch is a smart switch,
(RSTBTN)
(see p.2 No. 20)
Clear CMOS Switch Clear CMOS Switch is a smart
(CLRCBTN)
(see p.3 No. 14)
allowing users to quickly turn
on/off the system.
allowing users to quickly reset
the system.
switch, allowing users to quickly
clear the CMOS values
English
30
ASRock FM2A85X Extreme4 Motherboard
Page 31
2.9 Dr. Debug
Dr. Debug is used to provide code information, which makes troubleshooting even easier. Please see the diagrams below for reading the Dr. Debug codes.
Status Code Description
00 Please check if CPU is installed correctly and then clear CMOS.
0d Problem related to memory, VGA card and other devices. Please clear CMOS, re-install memory and VGA card, and remove other USB, PCI devices. 01 - 54 Problem related to memory. Please re-install CPU and memory then clear (except 0d), CMOS. 5A- 60 If the problem still exists, please install only one memory module or try using other memory modules. 55 Memory could not be detected. Please re-install memory and CPU. If the problem still exists, please install only one memory module or try using other memory modules. 61 - 91 Chipset initialization error. Please press reset or clear CMOS. 92 - 99 Problem related to PCI-E devices. Please re-install PCI-E devices or try installing them in other slots. If the problem still exists, please remove all PCI-E devices or try using another VGA card. A0 - A7 Problem related to IDE or SATA devices. Please re-install IDE and SATA devices. If the problem still exists, please clear CMOS and try removing all SATA devices. b0 Problem related to memory. Please re-install CPU and memory. If the problem still exists, please install only one memory module or try using other memory modules. * For X79 models, please try installing memory to DDR3_A1, B1, C1 and D1 slots. b4 Problem related to USB devices. Please try removing all USB devices. b7 Problem related to memory. Please re-install CPU and memory then clear CMOS. If the problem still exists, please install only one memory module or try using other memory modules. d6 VGA could not be recognized. Please clear CMOS and try re-installing the VGA card. If the problem still exists, please try installing the VGA card in other slots or using other VGA cards. d7 Keyboard and mouse could not be recognized. Please try re-installing keyboard and mouse. d8 Invalid Password. FF Please check if CPU is installed correctly and then clear CMOS.
English
ASRock FM2A85X Extreme4 Motherboard
31
Page 32
2.10 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical drive fi rst. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from up to bottom side to install those required drivers. Therefore, the drivers you install can work properly.
2.11 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / Vista
If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA3 HDDs with RAID functions, please refer to the document at the following path in the Support CD for detailed procedures:
..\ RAID Installation Guide
TM
64-bit With RAID Functions
2.12 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit Without RAID Functions
If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA3 HDDs without RAID functions, please follow below steps.
Using SATA3 HDDs without NCQ and Hot Plug functions (IDE mode)
English
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY Advanced screen Storage Confi guration. B. Set the “SATA Mode” option to [IDE].
STEP 2: Install Windows
your system.
Using SATA3 HDDs with NCQ and Hot Plug functions (AHCI mode)
STEP 1: Set up UEFI.
A. Enter UEFI SETUP UTILITY Advanced screen Storage Confi guration. B. Set the “SATA Mode” option to [AHCI].
STEP 2: Install Windows
your system.
®
8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on
®
8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on
32
ASRock FM2A85X Extreme4 Motherboard
Page 33
3. BIOS Information
The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the prede­termined choices. For the detailed information about BIOS Setup, please refer to the User Manual (PDF fi le) contained in the Support CD.
4. Software Support CD information
®
This motherboard supports various Microsoft 8 64-bit / 7 / 7 64-bit / VistaTM / Vista motherboard contains necessary drivers and useful utilities that will enhance moth­erboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double-click on the fi le “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
TM
Windows® operating systems: 8 /
64-bit. The Support CD that came with the
ASRock FM2A85X Extreme4 Motherboard
English
33
Page 34
1. Einführung
Wir danken Ihnen für den Kauf des ASRock FM2A85X Extreme4 Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes De­sign, gemäß der Verpfl ichtung von ASRock zu Qualität und Halbarkeit. Diese Sch- nellinstallationsanleitung führt in das Motherboard und die schrittweise Installation ein. Details über das Motherboard fi nden Sie in der Bedienungsanleitung auf der Support-CD.
Da sich Motherboard-Spezifi kationen und BIOS-Software verändern können, kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein. Die neuesten Grafi kkarten und unterstützten CPUs sind auch auf der ASRock-Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezifi sche Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite: www.asrock.com/support/index.asp
1.1 Kartoninhalt
ASRock FM2A85X Extreme4 Motherboard (ATX-Formfaktor) ASRock FM2A85X Extreme4 Schnellinstallationsanleitung ASRock FM2A85X Extreme4 Support-CD Vier Serial ATA (SATA) -Datenkabel (optional) Ein I/O Shield
Deutsch
34
ASRock erinnert...
Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / Vista / VistaTM 64 Bit empfehlen wir, die Speicherkonfi guration im BIOS auf den AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen fi nden Sie in der Bedienungsanleitung auf der mitgelieferten CD.
TM
ASRock FM2A85X Extreme4 Motherboard
Page 35
1.2 Spezifi kationen
Plattform - ATX-Formfaktor
- Alle Feste Kondensatordesign (100 % hochwertige japanische Fertigung leitfähiger Polymerkondensatoren) CPU - Unterstützt Sockel-FM2-100-W-Prozessoren
- 4 + 2-Stromphasendesign
- Unterstützt Cool ‘n’ Quiet
- UMI-Link-GEN2
Chipsatz - AMD A85X (Hudson-D4) Speicher - Unterstützung von Dual-Kanal-Speichertechnologie
- 4 x Steckplätze für DDR3
- Unterstützt DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/ 1600/1333/1066/800 non-ECC, ungepufferter Speicher
- Max. Kapazität des Systemspeichers: 64GB
- Unterstützt Intel
®
- Unterstützt AMD Memory Profi le (AMP) Erweiterungs- - 2 x PCI-Express-2.0-x16-Steckplätze steckplätze (PCIE2: x16-Modus; PCIE4: x4-Modus)
- 2 x PCI Express 2.0 x1-Steckplätze
- 3 x PCI -Steckplätze
- Unterstützt AMD Quad CrossFireX duale Grafi kkarten Onboard-VGA - AMD Radeon HD 7000-Grafi k
- DirectX 11, Pixel Shader 5.0
- Maximal gemeinsam genutzter Speicher 2GB
- Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie HDMI
- Unterstützt HDMI 1.4a mit einer maximalen Aufl ösung von 1920 x 1200 bei 60 Hz
- Unterstützt Dual-link DVI mit einer maximalen Aufl ösung von 2560 x 1600 bei 75 Hz
- Unterstützt D-Sub mit einer maximalen Aufl ösung von 1920 x 1600 bei 60 Hz
- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und HBR (High Bit Rate-Audio) mit HDMI (kompatibler HDMI- Bildschirm erforderlich)
- Unterstützt stereoskopisches 3D per Blu-ray mit HDMI 1.4a
- Unterstützt AMD Steady Video Videonachbearbeitung für automatische Reduzierung von Bildschwankungen bei Heim-/Online-Videos
- Unterstützt HDCP-Funktion mit DVI- und HDMI-Ports
TM
-Technologie von AMD
Extreme Memory Profi le (XMP)1.3/1.2
TM
, CrossFireXTM und
TM
2.0: Neuartige Funktion der
Deutsch
ASRock FM2A85X Extreme4 Motherboard
35
Page 36
Deutsch
36
- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit DVI- und HDMI-Ports Audio - 7.1 CH HD Audio mit dem Inhalt Schutz (Realtek ALC892 Audio Codec)
- Premium Blu-ray-Audio-Unterstützung
- Unterstützt THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Unterstützt Wake-On-LAN
- Unterstützt LAN-Kabelerkennung
- Unterstützt energieeffi zientes Ethernet 802.3az
- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Maus/Tastaturanschluss Rückseite - 1 x D-Sub port
- 1 x DVI-D port
- 1 x HDMI port
- 1 x optischer SPDIF-Ausgang
- 2 x Standard-USB 2.0-Anschlüsse
- 1 x eSATA3-Anschluss
- 6 x Standard-USB 3.0-Anschlüsse
- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)
- 1 x CMOS löschen-Schalter
- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass / Audioeingang / Lautsprecher vorne / Mikrofon SATA3 - 7 x SATA 3-Anschluss mit 6,0 Gb/s, unterstützt RAID­ (RAID 0, RAID 1, RAID 5 und RAID 10), NCQ-, AHCI- und „Hot Plugging“-Funktionen USB3.0 - 2 x USB 3.0-Ports an der Rückseite durch AMD A85X (Hudson-D4), unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s
- 4 x USB 3.0-Ports an der Rückseite durch Etron EJ188, unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s
- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der Vorderseite durch AMD A85X (Hudson-D4), unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s Anschlüsse - 7 x SATA3 6,0 GB/s-Anschlüsse
- 1 x Infrarot-Modul-Header
- 1 x
Consumer Infrarot-Modul-Header
- 1 x COM-Anschluss-Header
- 1 x HDMI_SPDIF-Anschluss
- 1 x Betriebs-LED-Header
ASRock FM2A85X Extreme4 Motherboard
Page 37
- 2 x CPUlüfter-Anschluss (1 x 4-pin, 1 x 3-pin)
- 3 x Gehäuselüfter-Anschluss (1 x 4-pin, 2 x 3-pin)
- 1 x Stromlüfter-Anschluss (3-pin)
- 24-pin ATX-Netz-Header
- 8-pin anschluss für 12V-ATX-Netzteil
- Anschluss für Audio auf der Gehäusevorderseite
- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher USB 2.0-Anschlüsse)
- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher USB 3.0-Anschlüsse)
- 1 x Dr. Debug (Debug-LED mit 7 Segmenten)
- 1 x Netzschalter mit LED
- 1 x Rücksetzschalter (Reset) mit LED BIOS - 64Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung
- Unterstützung für “Plug and Play”
- ACPI 1.1-Weckfunktionen
- JumperFree-Modus
- SMBIOS 2.3.1
- DRAM, APU PCIE VDDP, CPU und CPU NB/GFX Stromspannung Multianpassung Support-CD - Treiber, Dienstprogramme, Antivirussoftware (Probeversion), CyberLink MediaEspresso 6.5-Testversion, Google Chrome Browser und Toolbar Hardware Monitor - CPU-Temperatursensor
- Motherboardtemperaturerkennung
- Drehzahlmessung für CPU/Gehäuse/Stromlüfter
- Geräuscharmer CPUlüfter
- Mehrstufi ge Geschwindigkeitsteuerung für CPU-/ Gehäuselüfter
- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore
®
Betriebssysteme - Unterstützt Microsoft Vista
TM
/ Vista
Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /
TM
64-Bit
Zerti zierungen - FCC, CE, WHQL
- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)
* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com
Deutsch
ASRock FM2A85X Extreme4 Motherboard
37
Page 38
1.3 Einstellung der Jumper
Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Ge­brückt” sind, bzw. es befi ndet sich eine Jumper-Kappe auf diesen beiden Pins.
Jumper Einstellun Beschreibung
CMOS löschen
(CLRCMOS1, 3-Pin jumper) (siehe S.2, No. 27)
Hinweis:
CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte aus und trennen das Netzkabel von der Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Uhrzeit, benutzerdefi niertes Profi l, 1394 GUID und MAC-Adresse
nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.
Default­Einstellung
CMOS löschen
Deutsch
38
Der CMOS löschen-Schalter hat dieselbe Funktion wie der CMOS löschen-Jumper.
ASRock FM2A85X Extreme4 Motherboard
Page 39
1.4 Anschlüsse
Anschlussleisten sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf die Pins der Anschlussleisten. Wenn Sie die Jumperkappen auf die Anschlüsse setzen, wird das Motherboard permanent beschädigt!
Anschluss Beschreibung
Seriell-ATA3-Anschlüsse Diese sieben Serial ATA3-
(SATA3_1: siehe S.2 - No. 13)
(SATA3_2: siehe S.2 - No. 12)
(SATA3_3: siehe S.2 - No. 14)
(SATA3_4: siehe S.2 - No. 15)
(SATA3_5: siehe S.2 - No. 19)
(SATA3_6: siehe S.2 - No. 16)
(SATA3_7: siehe S.2 - No. 17)
6,0 Gb/s.
Serial ATA- (SATA-) SJedes Ende des SATA Datenkabel Datenkabels kann an die
(Option)
SATA3 Festplatte oder das SATA3 Verbindungsstück auf dieser Hauptplatine angeschlossen werden.
(SATA3-)Verbínder unterstützten SATA-Datenkabel für interne
Massenspeichergeräte. Die aktuelle SATA3- Schnittstelle ermöglicht eine
Datenübertragungsrate bis
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
USB 2.0-Header Zusätzlich zu den zwei
(9-pol. USB3_4)
(siehe S.2 - No. 30)
üblichen USB 2.0-Ports an den
I/O-Anschlüssen befi nden sich drei USB 2.0- Anschlussleisten am
(9-pol. USB5_6)
(siehe S.2 - No. 29)
Motherboard. Pro USB 2.0-
Anschlussleiste werden zwei
USB 2.0-Ports unterstützt.
(9-pol. USB7_8) (siehe S.2 - No. 28)
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-3
P-6
P+6
GND
DUMMY
GND
P+5
P-5
P-8
P+8
GND
DUMMY
GND
P+7
P-7
ASRock FM2A85X Extreme4 Motherboard
Deutsch
39
Page 40
USB 3.0-Header Neben sechs Standard-USB
(19-pol. USB3_7_8)
(siehe S.2 - No. 10)
Header an diesem Motherboard. Dieser USB 3.0­ Header kann zwei USB 3.0­ Ports unterstützen.
3.0-Ports am E/A-Panel befi ndet sich ein USB 3.0-
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
Deutsch
40
Infrarot-Modul-Header Dieser Header unterstützt ein
(5-pin IR1)
optionales, drahtloses Sende-
(siehe S.2 - No. 25)
und Empfangs-Infrarotmodul.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Consumer Infrared-Modul-Header Dieser Header kann zum
(4-pin CIR1)
(siehe S.2 - No. 31)
Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorder
(9-Pin HD_AUDIO1)
(siehe S.2 - No. 34)
Anschlussmöglichkeit und Kontrolle über Audio-Geräte.
1. High Defi nition Audio unterstützt Jack Sensing (automatische Erkennung falsch angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.
2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an. B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an.
Bei den Betriebssystemen Windows 64 Bit: Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)- Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke) an.
Anschließen Remote-
Empfänger.
GND
PRESENCE#
MIC_RET
OUT_RET
seite Ihres Gehäuses,
ermöglicht Ihnen eine bequeme
D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese
Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.
E. So aktivieren Sie das Mikrofon an der Vorderseite.
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
®
8 / 8 64 Bit / 7 / 7 64 Bit / VistaTM / VistaTM
ASRock FM2A85X Extreme4 Motherboard
Page 41
System Panel-Header Dieser Header unterstützt
(9-pin PANEL1)
(siehe S.2 - No. 21)
Schließen Sie die Ein-/Austaste, die Reset-Taste und die Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die positiven und negativen Pins, bevor Sie die Kabel anschließen.
PWRBTN (Ein-/Ausschalter):
RESET (Reset-Taste):
PLED (Systembetriebs-LED):
HDLED (Festplattenaktivitäts-LED):
mehrere Funktion der
Systemvorderseite.
Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu ses. Sie können konfi gurieren, wie das System mit Hilfe des Ein-/Ausschalters ausgeschaltet werden können soll.
Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses. Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes neu starten.
Zum Anschließen der Betriebsstatusanzeige an der Frontblende des Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt, wenn sich das System im Ruhezustand S1 befi ndet. Die LED schaltet sich aus, wenn sich das System in den Modi S3/S4 befi ndet oder ausgeschaltet ist (S5).
Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.
Das Design der Frontblende kann je nach Gehäuse variiere. Ein Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED, Lautsprechern, etc. Stellen Sie beim Anschließen des Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die Kabel- und Pinbelegung korrekt übereinstimmen.
ASRock FM2A85X Extreme4 Motherboard
Deutsch
41
Page 42
Gehäuselautsprecher-Header Schließen Sie den
(4-pin SPEAKER1)
(siehe S.2 - No. 23)
Gehäuselautsprecher an
diesen Header an.
Betriebs-LED-Header Bitte schließen Sie die
(3-pin PLED1)
(siehe S.2 - No. 26)
Betriebs-LED des Gehäuses
zur Anzeige des
1
PLED+
PLED+
PLED-
Systembetriebsstatus an diesem Header an. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt im S1-Zustand. Im S3-/S4- oder S5-Zustand (ausgeschaltet) leuchtet die LED nicht.
Gehäuse- und Stromlüfteranschlüsse Verbinden Sie die Lüfterkabel
(4-pin CHA_FAN1)
(siehe S.2, No. 24)
mit den Lüfteranschlüssen,
wobei der schwarze Draht an
den Schutzleiterstift
(3-pin CHA_FAN2)
(siehe S.2 - No. 43)
(3-pin CHA_FAN3)
(siehe S.2 - No. 44)
(3-pin PWR_FAN1)
(siehe S.2 - No. 1)
angeschlossenwird.
Deutsch
42
CPU-Lüfteranschluss Verbinden Sie das CPU -
(4-pin CPU_FAN1)
(siehe S.2 - No. 5)
Lüfterkabel mit diesem
Anschluss und passen Sie den schwarzen Draht dem Erdungsstift an.
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss (Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses Motherboards anschließen möchten, verbinden Sie ihn bitte mit den Pins 1 – 3.
Pins 1–3 anschließen
Lüfter mit dreipoligem Anschluss installieren
ASRock FM2A85X Extreme4 Motherboard
Page 43
(3-pin CPU_FAN2)
(siehe S.2 - No. 6)
GND
+12V
CPU_FAN_SPEED
ATX-Netz-Header Verbinden Sie die ATX-
(24-pin ATXPWR1)
(siehe S.2 - No. 9)
Obwohl dieses Motherboard einen 24-pol. ATX-
Stromversorgung mit diesem
Header.
12 124
13
12
24
Stromanschluss bietet, kann es auch mit einem modifi zierten traditionellen 20-pol. ATX-Netzteil verwendet werden. Um ein 20-pol. ATX-Netzteil zu verwenden, stecken Sie den Stecker mit Pin 1 und Pin 13 ein.
ATX 12V Anschluss Bitte schließen Sie an diesen
(8-pin ATX12V1)
(siehe S.2 - No. 2)
Anschluss die ATX 12V
Stromversorgung an.
Installation eines 20-pol. ATX-Netzteils
4 8
1 5
1
13
Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur Verfügung stellt, kann sie noch arbeiten, wenn Sie einen traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die 4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.
4 8
Installation der 4-Pin ATX 12V Energieversorgung
1 5
COM-Anschluss-Header Dieser COM-Anschluss-
(9-pin COM1)
(siehe S.2 - No. 32)
Header wird verwendet, um
ein COM-Anschlussmodul zu
unterstützen.
Deutsch
ASRock FM2A85X Extreme4 Motherboard
43
Page 44
HDMI_SPDIF-Anschluss Der HDMI_SPDIF-Anschluss
(2-pin HDMI_SPDIF1)
(siehe S.2 - No. 33)
stellt einen SPDIF-
Audioausgang für eine HDMI­ VGA-Karte zur Verfügung und ermöglicht den Anschluss von HDMI-Digitalgeräten wie Fernsehgeräten, Projektoren, LCD-Geräten an das System. Bitte verbinden Sie den HDMI_SPDIF-Anschluss der HDMI-VGA-Karte mit diesem Anschluss.
1.5 Schnellschalter
Dieses Motherboard besitzt drei Schnellschalter: Netzschalter, Rücksetzschalter (Reset) und CMOS löschen-Schalter, mit denen Benutzer das System schnell ein-/ ausschalten oder zurücksetzen oder die CMOS-Werte löschen können.
Netzschalter Der Netzschalter ist ein
(PWRBTN)
(siehe S.2 - No. 22)
ein-/ausschalten können.
Schnellschalter, mit dem
Benutzer das System schnell
Deutsch
44
Rücksetzschalter (Reset) Der Rücksetzschalter (Reset)
(RSTBTN)
ist ein Schnellschalter, mit dem
(siehe S.2 - No. 20)
Benutzer das System schnell zurücksetzen können.
CMOS löschen-Schalter Der CMOS löschen-Schalter ist
(CLRCBTN)
(siehe S.3 - No. 14)
ein Schnellschalter, mit dem
Benutzer die CMOS-Werte schnell löschen können.
ASRock FM2A85X Extreme4 Motherboard
Page 45
2. BIOS-Information
Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie <F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelan­gen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch durchführen, indem Sie das System kurz ab- und danach wieder anschalten. Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrol­len und die vorab festgelegten Optionen auswählen können. Für detaillierte Infor­mationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der Support CD.
3. Software Support CD information
Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebs­systemen: 8 / 8 64-Bit / 7 / 7 64-Bit / Vista beigefügte Support-CD enthält hilfreiche Software, Treiber und Hilfsprogramme, mit denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben. Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen. Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menüges­teuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und die Programme werden dann automatisch installiert.
TM
/ VistaTM 64-Bit. Die Ihrem Motherboard
ASRock FM2A85X Extreme4 Motherboard
Deutsch
45
Page 46
1. Introduction
Merci pour votre achat d’une carte mère ASRock FM2A85X Extreme4, une carte mère très fiable produite selon les critères de qualité rigoureux de ASRock. Elle offre des performances excellentes et une conception robuste conformément à l’engagement d’ASRock sur la qualité et la fi abilité au long terme. Ce Guide d’installation rapide présente la carte mère et constitue un guide d’installation pas à pas. Des informations plus détaillées concernant la carte mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD d’assistance.
Les spécifi cations de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notifi cation. Au cas où n’importe qu’elle modifi cation intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis. Vous trouverez les listes de prise en charge des cartes VGA et CPU également sur le site Web ASRock. Site web ASRock, http://www.asrock.com Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez. www.asrock.com/support/index.asp
1.1 Contenu du paquet
Carte mère ASRock FM2A85X Extreme4 (Facteur de forme ATX) Guide d’installation rapide ASRock FM2A85X Extreme4 CD de soutien ASRock FM2A85X Extreme4 Quatre câbles de données de série ATA (SATA) (en option) Un I/O Panel Shield
Français
46
ASRock vous rappelle...
Pour bénéfi cier des meilleures performances sous Windows® 8 / 8 64 bits / 7 / 7 64 bits / Vista l'option BIOS dans Confi guration de stockage en mode AHCI. Pour plus de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur votre CD de support.
TM
/ VistaTM 64 bits, il est recommandé de paramétrer
ASRock FM2A85X Extreme4 Motherboard
Page 47
1.2 Spécifi cations
Format - Facteur de forme ATX
- Accessoires de Carte mère (condensateurs polymère conducteur de qualité supérieure 100% fabriqués au Japon) CPU - Support des unités centrales Socket FM2 100W
- Conception 4 + 2 Power Phase
- Supporte la technologie Cool ‘n’ Quiet
- UMI-Link GEN2
Chipsets - AMD A85X (Hudson-D4) Mémoire - Compatible avec la Technologie de Mémoire à Canal
Double
- 4 x slots DIMM DDR3
- Supporter DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/ 1600/1333/1066/800 non-ECC, sans amortissement mémoire
- Capacité maxi de mémoire système: 64GB
- Prend en charge le profi l de mémoire extrême Intel
1.3/1.2
- Prend en charge le profi l de mémoire AMD (AMP) Slot d’extension - 2 x fentes PCI Express 2.0 x16 (PCIE2 à mode x16; PCIE4 à mode x4)
- 2 x slots PCI Express 2.0 x1
- 3 x slots PCI
- Support de AMD Quad CrossFireX Graphics VGA sur carte - Graphiques à l’AMD Radeon HD 7000
- DirectX 11, nuanceur de pixels 5.0
- mémoire partagée max 2GB
- Trois options de sortie VGA: D-Sub, DVI-D et HDMI
- Prend en charge le HDMI 1.4a avec une résolution maximale jusqu’à 1920x1200 @ 60Hz
- Prend en charge le Dual-link DVI avec une résolution maximale jusqu’à 2560x1600 @ 75Hz
- Prend en charge le D-Sub avec une résolution maximale jusqu’à 1920x1600 @ 60Hz
- Prend en charge Lip Sync, Deep Color (12bpc), xvYCC et HBR (High Bit Rate Audio: Audio à haut débit binaire) avec HDMI (Moniteur compatible HDMI requis)
- Prend en charge la 3D stéréoscopique Blu-ray avec HDMI 1.4a
TM
d’AMD
®
(XMP)
TM
, CrossFireXTM et Dual
Français
ASRock FM2A85X Extreme4 Motherboard
47
Page 48
Français
48
- Supporte AMD Steady VideoTM 2.0: Nouvelle fonctionnalité de traitement post-vidéo pour réduction automatique des tremblements dans les clips vidéo en ligne/maison
- Prise en charge de la fonction HDCP avec ports DVI et HDMI
- Supporter 1080p Blu-ray(BD)/ lecteur de HD-DVD avec ports DVI et HDMI Audio - 7,1 CH HD Audio avec protection de contenu (Realtek ALC892 Audio Codec)
- Prise en charge de l’audio Premium Blu-ray
- Prend en charge THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supporte du Wake-On-LAN
- Prise en charge de la détection de câble LAN
- Prend en charge la norme Energy Effi cient Ethernet (Ethernet à effi cacité énergétique) 802.3az
- Supporte PXE
Panneau arrière I/O Panel
- 1 x port souris/clavier PS/2
- 1 x port D-Sub
- 1 x port DVI-D
- 1 x port HDMI
- 1 x Port de sortie optique SPDIF
- 2 x ports USB 2.0 par défaut
- 1 x Connecteur eSATA3
- 6 x ports USB 3.0 par défaut
- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et LED VITESSE)
- 1 x interrupteur d’effacement du CMOS
- Prise HD Audio: Haut-parleur arrière / Central /Basses / Entrée Ligne / Haut-parleur frontal / Microphone SATA 3 - 7 x connecteurs 6,0 Gb/s SATA3, prise en charge des fonctions RAID (RAID 0, RAID 1, RAID 5 et RAID 10), NCQ, AHCI et « Connexion à chaud » USB 3.0 - 2 x ports USB3.0 à l’arrière par AMD A85X (Hudson-D4), prennent en charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s
- 4 x ports USB3.0 à l’arrière par Etron EJ188, prennent en charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s
- 1 x barrette USB3.0 en façade (prend en charge 2 ports USB 3.0) par AMD A85X (Hudson-D4), prend en charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s
ASRock FM2A85X Extreme4 Motherboard
Page 49
Connecteurs - 7 x connecteurs SATA3, prennent en charge un taux de
transfert de données pouvant aller jusqu’à 6.0Go/s
- 1 x En-tête du module infrarouge
- 1 x
Barrette pour module à infrarouges grand public
- 1 x En-tête de port COM
- 1 x Connecteur HDMI_SPDIF
- 1 x LED di accensione
- 2 x Connecteur pour ventilateur de CPU (1 x br. 4, 1 x br. 3)
- 3 x Connecteur pour ventilateur de Châssis (1 x br. 4, 2 x br. 3)
- 1 x Connecteur pour ventilateur de pouvoir (br. 3)
- br. 24 connecteur d’alimentation ATX
- br. 8 connecteur d’alimentation 12V ATX
- Connecteur audio panneau avant
- 3 x En-tête USB 2.0 (prendre en charge 6 ports USB 2.0 supplémentaires)
- 1 x En-tête USB 3.0 (prendre en charge 2 ports USB 3.0 supplémentaires)
- 1 x Dr. Debug (LED de débogage à 7 segments)
- 1 x interrupteur d’alimentation avec LED
- 1 x interrupteur de réinitialisation avec LED BIOS - 64Mb AMI UEFI Legal BIOS avec support GUI
- Support du “Plug and Play”
- Compatible pour événements de réveil ACPI 1.1
- Gestion jumperless
- Support SMBIOS 2.3.1
- DRAM, APU PCIE VDDP, CPU et CPU NB/GFX Tension Multi-ajustement CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (Version d’essai), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser et Toolbar Surveillance - Détection de la température de l’UC système - Mesure de température de la carte mère
- Tachéomètre ventilateur CPU/Châssis/Ventilateur
- Ventilateur silencieux pour unité centrale
- Commande de ventilateur CPU/boîtier à plusieurs vitesses
- Monitoring de la tension: +12V, +5V, +3.3V, Vcore OS - Microsoft
®
Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista
TM
/
VistaTM 64-bit Certi cations - FCC, CE, WHQL
- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)
Français
ASRock FM2A85X Extreme4 Motherboard
49
Page 50
* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web: http://www.asrock.com
1.3 Réglage des cavaliers
L’illustration explique le réglage des cava­liers. Quand un capuchon est placé sur les broches, le cavalier est « FERME ». Si au­cun capuchon ne relie les broches,le cava­lier est « OUVERT ». L’illustration montre un cavalier à 3 broches dont les broches 1 et 2 sont « FERMEES » quand le capuchon est placé sur ces 2 broches.
Le cavalier Description
Effacer la CMOS
(CLRCMOS1) (voir p.2 fi g. 27)
Remarque :
Paramètres par défaut
CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer et réinitialiser les paramètres du système à la confi guration originale, veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de la prise de courant. Après 15 secondes, utilisez un couvercle de jumper pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant secondes. Veuillez cependant ne pas effacer le CMOS immédiatement a
près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS après avoir mis à jour le BIOS, vous devez allumer en premier le système, puis l’éteindre avant de continuer avec l’opération d’effacement du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le profi l par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés seulement si la batterie du CMOS est enlevée.
Effacer la CMOS
5
Français
50
Le commutateur Effacer CMOS présente la même fonction que le cavalier Effacer CMOS.
ASRock FM2A85X Extreme4 Motherboard
Page 51
1.4 En-têtes et Connecteurs sur Carte
Connecteurs Série ATA3 Ces sept connecteurs Série
(SATA3_1: voir p.2 No. 13)
(SATA3_2: voir p.2 No. 12)
(SATA3_3 voir p.2 No. 14)
(SATA3_4 voir p.2 No. 15)
(SATA3_5 voir p.2 No. 19)
(SATA3_6 voir p.2 No. 16)
(SATA3_7 voir p.2 No. 17)
Câble de données Toute cote du cable de data Série ATA (SATA) SATA peut etre connecte au
(en option)
connecteur SATA3 sur la carte mere.
Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers. NE PAS placer les capuchons de cavalier sur ces en-têtes et con­necteurs. Le fait de placer les capuchons de cavalier sur les en­têtes et connecteurs causera à la carte mère des dommages irré­versibles!
ATA3 (SATA3) prennent en
charge les câbles SATA pour les périphériques de stockage internes. L’interface SATA3 actuelle permet des taux transferts de données pouvant aller jusqu’à 6,0 Gb/s.
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
disque dur SATA3 ou au
En-tête USB 2.0 A côté des deux ports USB
(USB3_4 br.9)
(voir p.2 No. 30)
2.0 par défaut sur le panneau E/S, il y a trois embases USB
2.0 sur cette carte mère. Chaque embase USB 2.0 peut
(USB5_6 br.9)
(voir p.2 No. 29)
(USB7_8 br.9) (voir p.2 No. 28)
prendre en charge 2 ports USB
2.0.
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-3
P-6
P+6
GND
DUMMY
GND
P+5
P-5
P-8
P+8
GND
DUMMY
GND
P+7
P-7
ASRock FM2A85X Extreme4 Motherboard
Français
51
Page 52
En-tête USB 3.0 En plus des six ports USB
(USB3_7_8 br. 19)
(voir p.2 No. 10)
sur la carte mère. Cette barrette USB 3.0 peut prendre en charge deux ports USB 3.0.
3.0 par défaut sur le panneau
E/S, il y a une barrette USB 3.0
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
Français
En-tête du module infrarouge Cet en-tête supporte un module
(IR1 br.5)
infrarouge optionnel de
(voir p.2 No. 25)
transfert et de réception sans
fi l.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Barrette pour module à infrarouges grand public Cette barrette peut être utilisée
(CIR1 br.4)
(voir p.2 No. 31)
Connecteur audio panneau C’est une interface pour
(HD_AUDIO1 br. 9)
(voir p.2 No. 34)
le contrôle commodes de périphériques audio.
1. L’audio à haute défi nition (HDA) prend en charge la détection de fi che, mais le fi l de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de châssis afi n installer votre système.
2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio du panneau avant conformément à la procédure ci-dessous : A. Connectez Mic_IN (MIC) à MIC2_L. B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L. C. Connectez Ground (GND) à Ground (GND). D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous n’avez pas besoin de les connecter pour le panneau audio AC’97. E. Pour activer le micro avant. Pour les systèmes d’exploitation Windows VistaTM 64 bits : Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).
pour connecter des récepteur
GND
PRESENCE#
un câble avant audio en façade
MIC_RET
OUT_RET
qui permet le branchement et
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
®
8 / 8 64 bits / 7 / 7 64 bits / VistaTM /
52
ASRock FM2A85X Extreme4 Motherboard
Page 53
En-tête du panneau système Cet en-tête permet d’utiliser
(PANEL1 br.9)
(voir p.2 No. 21)
Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et l’indicateur d’état du système du châssis sur cette barrette en respectant l’affectation des broches décrite ci-dessous. Faites attention aux broches positives et négatives avant de connecter les câbles.
PWRBTN (Interrupteur d’alimentation):
RESET (Interrupteur de réinitialisation):
PLED (DEL alimentation système):
HDLED (DEL activité du disque dur):
plusieurs fonctions du
panneau système frontal.
Connectez ici le connecteur d’alimentation sur le panneau avant du châssis. Vous pouvez confi gurer la façon de mettre votre système hors tension avec l’interrupteur d’alimentation.
Connectez ici le connecteur de réinitialisation sur le panneau avant du châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.
Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le système est en marche. Le voyant DEL clignote lorsque le système est en mode veille S1. Le voyant DEL est éteint lorsque le système est en mode veille S3/ S4 ou lorsqu’il est éteint (S5).
Connectez ici le voyant DEL d’activité du disque dur sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en train de lire ou d’écrire des données.
Le design du panneau avant peut varier en fonction du châssis. Un module de panneau avant consiste principalement en : interrupteur d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation, voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous connectez le panneau avant de votre châssis sur cette barrette, vérifi ez bien à faire correspondre les fi ls et les broches.
ASRock FM2A85X Extreme4 Motherboard
Français
53
Page 54
En-tête du haut-parleur Veuillez connecter le de châssis haut-parleur de châssis sur
(SPEAKER1 br. 4)
(voir p.2 No. 23)
cet en-tête.
LED di accensione Collegare il LED di accensione
(3-pin PLED1)
(vedi p.2 Nr. 26)
chassi per indicare lo stato di
alimentazione del sistema. Il
1
PLED+
PLED+
PLED-
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
Connecteur pour châssis et ventilateur
(CHA_FAN1 br. 4)
(voir p.2 No. 24)
Branchez les câbles du ventilateur aux connecteurs pour ventilateur et faites correspondre le fi l noir à la broche de terre.
(CHA_FAN2 br. 3) (voir p.2 No. 43)
(CHA_FAN3 br. 3) (voir p.2 No. 44)
(PWR_FAN1 br. 3)
(voir p.2 No. 1)
Connecteur du ventilateur Veuillez connecter le câble de de l’UC ventilateur d’UC sur ce
(CPU_FAN1 br. 4)
(voir p.2 No. 5)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
connecteur et brancher le fi l
noir sur la broche de terre.
GND
1 2 3 4
Français
54
Bien que cette carte mère offre un support de (Ventilateur silencieux ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut bien fonctionner même sans la fonction de commande de vitesse du ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3 broches au connecteur du ventilateur de CPU sur cette carte mère, veuillez le connecter aux broches 1-3.
Installation de ventilateur à 3 broches
Broches 1-3 connectées
ASRock FM2A85X Extreme4 Motherboard
Page 55
(CPU_FAN2 br. 3)
(voir p.2 No. 6)
GND
+12V
CPU_FAN_SPEED
En-tête d’alimentation ATX Veuillez connecter l’unité
(ATXPWR1 br. 24)
(voir p.2 No. 9)
Bien que cette carte mère fournisse un connecteur de courant ATX 24 broches, elle peut encore fonctionner
d’alimentation ATX sur cet en-
tête.
12 124
13
12
24
si vous adopter une alimentation traditionnelle ATX 20 broches. Pour utiliser une alimentation ATX 20 broches, branchez à l’alimentation électrique ainsi qu’aux broches 1 et 13.
20-Installation de l’alimentation électrique ATX
Connecteur ATX 12V Veuillez connecter une unité
(ATX12V1 br.8)
(voir p.2 No. 2)
d’alimentation électrique ATX 12V sur ce connecteur.
4 8
1 5
1
13
Bien que cette carte mère possède 8 broches connecteur d’alimentation ATX 12V, il peut toujours travailler si vous adoptez une approche traditionnelle à 4 broches ATX 12V alimentation. Pour utiliser l’alimentation des 4 broches ATX, branchez votre alimentation avec la broche 1 et la broche 5.
4-Installation d’alimentation à 4 broches ATX 12V
4 8
1 5
En-tête de port COM Cette en-tête de port COM est
(COM1 br.9)
(voir p.2 No. 32)
utilisée pour prendre en charge
un module de port COM.
ASRock FM2A85X Extreme4 Motherboard
Français
55
Page 56
Connecteur HDMI_SPDIF Connecteur HDMI_SPDIF,
(HDMI_SPDIF1 2-pin)
(voir p.2 No. 33)
fournissant une sortie audio
SPDIF vers la carte VGA HDMI, et permettant au système de se connecter au un téléviseur numérique HDMI /un projecteur / un périphérique LCD. Veuillez brancher le connecteur HDMI_SPDIF de la carte VGA HDMI sur ce connecteur.
Français
56
ASRock FM2A85X Extreme4 Motherboard
Page 57
1.5 Interrupteur rapides
Cette carte mère dispose de trois interrupteurs rapides : un interrupteur d’alimenta­tion, un interrupteur de réinitialisation et un interrupteur d’effacement de CMOS, per­mettant aux utilisateurs de rapidement allumer/éteindre ou réinitialiser le système, ainsi que d’effacer les valeurs du CMOS.
Interrupteur d’alimentation
(PWRBTN) (voir p.2 No. 22)
Interrupteur de réinitialisation
(RSTBTN) (voir p.2 No. 20)
Interrupteur d’effacement de CMOS
(CLRCBTN) (voir p.3 No. 14)
L’interrupteur d’alimentation est un interrupteur rapide, qui permet à l’utilisateur d’allumer/éteindre rapidement le système.
L’interrupteur de réinitialisation est un interrupteur rapide, qui permet à l’utilisateur de réinitialiser rapidement le système.
L’interrupteur d’effacement de CMOS est un interrupteur rapide qui permet à l’utilisateur d’effacer rapidement les valeurs du CMOS.
ASRock FM2A85X Extreme4 Motherboard
Français
57
Page 58
2. Informations sur le BIOS
La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-On­Self-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier du système. Vous pouvez également redémarrer en éteignant le système et en le rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un programme piloté par menu, qui vous permet de faire défi ler par ses divers sous- menus et de choisir parmi les choix prédéterminés. Pour des informations détaillées sur le BIOS, veuillez consulter le Guide de l’utilisateur (fi chier PDF) dans le CD technique.
3. Informations sur le CD de support
Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®: 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / Vista carte mère contient les pilotes et les utilitaires nécessaires pour améliorer les fonc­tions de la carte mère. Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu principal s’affi che automatiquement si “AUTORUN” est activé dans votre ordinateur. Si le Menu principal n’apparaît pas automatiquement, locali­sez dans le CD technique le fi chier “ASSETUP.EXE” dans le dossier BIN et double- cliquez dessus pour affi cher les menus.
TM
64 bits. Le CD technique livré avec cette
Français
58
ASRock FM2A85X Extreme4 Motherboard
Page 59
1. Introduzione
Grazie per aver scelto una scheda madre ASRock FM2A85X Extreme4, una sche­da madre affi dabile prodotta secondo i severi criteri di qualità ASRock. Le prestazi- oni eccellenti e il design robusto si conformano all’impegno di ASRock nella ricerca della qualità e della resistenza. Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si possono trovare nel manuale per l’utente presente nel CD di supporto.
Le specifi che della scheda madre e il software del BIOS possono essere aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia modifi cato, la versione aggiornata sarà disponibile sul sito di ASRock senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate. ASRock website http://www.asrock.com Se si necessita dell’assistenza tecnica per questa scheda madre, visitare il nostro sito per informazioni specifi che sul modello che si sta usando. www.asrock.com/support/index.asp
1.1 Contenuto della confezione
Scheda madre ASRock FM2A85X Extreme4 (ATX Form Factor) Guida di installazione rapida ASRock FM2A85X Extreme4 CD di supporto ASRock FM2A85X Extreme4 Quattro cavi dati Serial ATA (SATA) (opzionali) Un I/O Shield
ASRock vi ricorda...
Per ottenere migliori prestazioni in Windows® 8 / 8 64-bit / 7 / 7 64-bit /
TM
Vista
/ VistaTM 64-bit, si consiglia di impostare l'opzione BIOS in Storage Confi guration (Confi gurazione di archiviazione) sulla modalità AHCI. Per l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'uten­te) nel CD di supporto per dettagli.
ASRock FM2A85X Extreme4 Motherboard
Italiano
59
Page 60
Italiano
1.2 Specifi che
Piattaforma - ATX Form Factor
- Design condensatore compatto (condensatori a polimeri conduttivi di altissima qualità 100% made in Japan) Processore - Supporto per processori socket FM2 100W
- Struttura di fase con alimentazione 4 + 2
- Supporto tecnologia AMD Cool ‘n’ Quiet
- UMI-Link GEN2 Chipset - AMD A85X (Hudson-D4) Memoria - Supporto tecnologia Dual Channel Memory
- 4 x slot DDR3 DIMM
- Supporto DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/ 1333/1066/800 non-ECC, momoria senza buffer
- Capacità massima della memoria di sistema: 64GB
- Supporto di Intel
®
XMP (Extreme Memory Profi le)1.3/1.2
- Supporto di AMD AMP (AMD Memory Profi le) Slot di - 2 x alloggiamenti PCI Express 2.0 x16 espansione (PCIE2: modalità x16; PCIE4: modalità x4)
- 2 x slot PCI Express 2.0 x1
- 3 x slot PCI
- Supporta AMD Quad CrossFireX Graphics VGA su scheda - Grafi ca AMD Radeon HD 7000
- DirectX 11, Pixel Shader 5.0
- Memoria massima condivisa 2GB
- Tre opzioni d’output VGA: D-Sub, DVI-D e HDMI
- Supporta HDMI 1.4a con risoluzione massima fi no a 1920x1200 @ 60Hz
- Supporta Dual-link DVI con risoluzione massima fi no a 2560x1600 @ 75Hz
- Supporta D-Sub con risoluzione massima fi no a 1920x1600 @ 60Hz
- Supporto delle funzioni Auto Lip Sync, Deep Color (12bpc), xvYCC e HBR (High Bit Rate Audio) con HDMI (è necessario un monitor compatibile HDMI)
- Supporta Blu-ray Stereoscopico in 3D con HDMI 1.4a
- Supporta AMD Steady Video
TM
2.0: Nuova capacità di post-elab orazione video per la riduzione automatica delle vibrazioni nei video a casa/on-line
- Supporto della funzione HDCP con le porte DVI e HDMI
TM
TM
, CrossFireXTM e Dual
60
ASRock FM2A85X Extreme4 Motherboard
Page 61
- Supporto 1080p Blu-ray (BD) / HD-DVD riproduzione con le porte DVI e HDMI Audio - 7.1 CH HD Audio con protezioni contenuti (Realtek ALC892 Audio Codec)
- Supporto audio Blu-ray Premium
- Supporto THX TruStudio
TM
LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Supporta Wake-On-LAN
- Supporta il rilevamento cavo LAN
- Supporto di Energy Effi cient Ethernet 802.3az
- Supporta PXE Pannello I/O Panel posteriore - 1 x porta PS/2 per mouse/tastiera I/O - 1 x Porta D-Sub
- 1 x Porta DVI-D
- 1 x Porta HDMI
- 1 x Porta ottica SPDIF Out
- 2 x porte USB 2.0 già integrate
- 1 x Connettore eSATA3
- 6 x porte USB 3.0 già integrate
- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e LED velocità)
- 1 x interruttore di pulizia CMOS
- Connettore HD Audio: cassa posteriore / cassa centrale / bassi / ingresso linea / cassa frontale / microfono SATA3 - 7 x connettori SATA3 6,0 Gb/s, supporto di RAID (RAID 0, RAID 1, RAID 5 e RAID 10) e delle funzioni NCQ, AHCI e “Hot Plug” USB 3.0 - 2 x porte USB 3.0 posteriori amministrate dal controller AMD A85X (Hudson-D4), supporto di USB 1.1/2.0/3.0 fi no a 5Gb/s
- 4 x porte USB 3.0 posteriori amministrate dal controller Etron EJ188, supporto di USB 1.1/2.0/3.0 fi no a 5Gb/s
- 1 x header USB 3.0 frontale (supporta 2 porte USB 3.0) amministrato dal controller AMD A85X (Hudson-D4), supporto di USB 1.1/2.0/3.0 fi no a 5Gb/s Connettori - 7 x connettori SATA3 6.0Go/s
- 1 x Collettore modulo infrarossi
- 1 x
Connettore modulo infrarosso consumer
- 1 x collettore porta COM
Italiano
ASRock FM2A85X Extreme4 Motherboard
61
Page 62
Italiano
- 1 x Header HDMI_SPDIF
- 1 x LED di accensione
- 2 x Connettore CPU ventola (1 x 4-pin, 1 x 3-pin)
- 3 x Connettore Chassis ventola (1 x 4-pin, 2 x 3-pin)
- 1 x Connettore Alimentazione ventola (3-pin)
- 24-pin collettore alimentazione ATX
- 8-pin connettore ATX 12V
- Connettore audio sul pannello frontale
- 3 x Collettore USB 2.0 (supporta 6 porte USB 2.0)
- 1 x Collettore USB 3.0 (supporta 2 porte USB 3.0)
- 1 x Dr. Debug (LED debug con 7 segmenti)
- 1 x interruttore di alimentazione con LED
- 1 x interruttore di reset con LED BIOS - 64Mb AMI UEFI Legal BIOS con interfaccia di supporto
- Supporta “Plug and Play”
- Compatibile con ACPI 1.1 wake up events
- Supporta jumperfree
- Supporta SMBIOS 2.3.1
- Regolazione multi-voltaggio DRAM, APU PCIE VDDP, CPU e CPU NB/GFX CD di - Driver, utilità, software antivirus (Versione dimostrativa), supporto CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser e Toolbar Monitoraggio - Sensore per la temperatura del processore Hardware - Sensore temperatura scheda madre
- Indicatore di velocita per la ventola del CPU/Chassis/ Alimentazione
- Ventola CPU silenziosa
- Ventola CPU/chassis con controllo di varie velocità
- Voltaggio: +12V, +5V, +3.3V, Vcore Compatibi- - Microsoft
lità SO
64 bit
®
Windows® 8 / 8 64 bit / 7 / 7 64 bit / VistaTM / Vista
Certi cazioni - FCC, CE, WHQL
- Predisposto ErP/EuP (è necessaria l’alimentazione predis posta per il sistema ErP/EuP)
* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com
TM
62
ASRock FM2A85X Extreme4 Motherboard
Page 63
1.3 Setup dei Jumpers
L’illustrazione mostra come sono settati i jump­er. Quando il ponticello è posizionato sui pin, il jumper è “CORTOCIRCUITATO”. Se sui pin non ci sono ponticelli, il jumper è “APERTO”. L’illustrazione mostra un jumper a 3 pin in cui il pin1 e il pin2 sono “CORTOCIRCUITATI” quan­do il ponticello è posizionato su questi pin.
Jumper Settaggio del Jumper
Resettare la CMOS
(CLRCMOS1) (vedi p.2 item 27)
Nota:
CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare i
parametri del sistema sulla confi gurazione iniziale, spegnere il computer e
Impostazione
predefi nita
scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi, poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. No­tare che password, data, ore, profi lo utente predefi nito, 1394 GUID e indirizzo MAC saranno cancellati solo se è rimossa la batteria della CMOS.
Azzeramen-
to CMOS
L’interruttore Clear CMOS (Cancella CMOS) ha la stessa funzione del jumper Clear CMOS.
ASRock FM2A85X Extreme4 Motherboard
Italiano
63
Page 64
1.4 Collettori e Connettori su Scheda
Connettori Serial ATA3 Questi sette connettori Serial
(SATA3_1: vedi p.2 Nr. 13)
(SATA3_2: vedi p.2 Nr. 12)
(SATA3_3: vedi p.2 Nr. 14)
(SATA3_4: vedi p.2 Nr. 15)
(SATA3_5: vedi p.2 Nr. 19)
(SATA3_6: vedi p.2 Nr. 16)
(SATA3_7: vedi p.2 Nr. 17)
trasferimento dati fi no a
6.0 Gb/s.
Cavi dati Serial ATA (SATA) Una o altra estremità del cavo
(Opzionale)
collegata al disco rigido SATA3 o al connettore di SATA3 su questa cartolina base.
I collettori ed i connettori su scheda NON sono dei jumper. NON instal­lare cappucci per jumper su questi collettori e connettori. L’installazione di cappucci per jumper su questi collettori e connettori provocherà danni permanenti alla scheda madre!
ATA3 (SATA3) supportano cavi
dati SATA per dispositivi di immagazzinamento interni. ATA3 (SATA3) supportano cavi SATA per dispositivi di memoria interni. L’interfaccia SATA3 attuale permette velocità di
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
di dati SATA può essere
Italiano
Collettore USB 2.0 Oltre alle due porte USB 2.0
(9-pin USB3_4)
(vedi p.2 Nr. 30)
predefi nite nel pannello I/O, la
scheda madre dispone di tre intestazioni USB 2.0. Ciascuna intestazione USB 2.0 supporta due porte USB 2.0.
(9-pin USB5_6) (vedi p.2 Nr. 29)
(9-pin USB7_8) (vedi p.2 Nr. 28)
USB_PWR
1
P-3
USB_PWR
USB_PWR
1
P-5
USB_PWR
USB_PWR
1
P-7
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-6
P+6
GND
DUMMY
GND
P+5
P-8
P+8
GND
DUMMY
GND
P+7
64
ASRock FM2A85X Extreme4 Motherboard
Page 65
Collettore USB 3.0 Oltre alle sei porte USB 3.0
(19-pin USB3_7_8)
(vedi p.2 Nr. 10)
standard del pannello I/O,
questa scheda madre è dotata di un header USB 3.0 che supporta due porte USB 3.0.
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
Collettore modulo infrarossi Questo collettore supporta
(5-pin IR1)
moduli ad infrarossi optional
(vedi p.2 Nr. 25)
per la trasmissione e la ricezione senza fi li.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Connettore modulo infrarosso consumer Questo connettore può essere
(4-pin CIR1)
(vedi p.2 Nr. 31)
Connettore audio sul È un’interfaccia per il cavo del pannello frontale pannello audio. Che consente
(9-pin HD_AUDIO1)
(vedi p.2 Nr. 34)
1. La caratteristica HDA (High Defi nition Audio) supporta il rilevamento dei connettori, però il pannello dei cavi sul telaio deve supportare la funzione HDA (High Defi nition Audio) per far sì che questa operi in modo corretto. Attenersi alle istruzioni del nostro manuale e del manuale del telaio per installare il sistema.
2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio del pannello anteriore, come indicato di seguito:
Sistema operativo Windows 64-bit: Andare alla scheda “FrontMic” (Microfono frontale) del pannello di controllo Realtek. Regolare la voce “Recording Volume” (Volume registrazione).
utilizzato per collegare
ricevitore remoto.
GND
PRESENCE#
MIC_RET
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT_RET
OUT2_L
®
8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM
connessione facile e controllo
dei dispositivi audio.
A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L. C. Collegare Ground (GND) a Ground (GND).
D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97.
E. Per attivare il microfono frontale.
1
ASRock FM2A85X Extreme4 Motherboard
Italiano
65
Page 66
Collettore pannello di sistema Questo collettore accomoda
(9-pin PANEL1)
(vedi p.2 Nr. 21)
Collegare l’interruttore d’alimentazione, l’interruttore di ripristino, l’indicatore di stato del sistema del pannello frontale del telaio a questo header in base all’assegnazione dei pin defi nita di seguito. Determinare i pin positivi e negativi prima di collegare i cavi.
PWRBTN (interruttore d’alimentazione):
RESET (interruttore di ripristino):
PLED (LED alimentazione del sistema):
HDLED (LED attività disco rigido):
diverse funzioni di sistema
pannello frontale.
Va collegato all’interruttore d’alimentazione del pannello frontale del telaio. Usando l’interruttore d’alimentazione si può confi gurare il modo in cui si spegne il sistema.
Va collegato all’interruttore di ripristino del pannello frontale del telaio. Premere l’interruttore di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.
Va collegato all’indicatore di stato d’alimentazione del pannello frontale del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua a lampeggiare quando il sistema è in stato di standby S1. Il LED è spento quando il sistema è in stato di sospensione /ibernazione S3/S4 oppure spento (S5).
Va collegato al LED attività disco rigido del pannello frontale del telaio. Il LED è acceso quando disco rigido legge e scrive i dati.
Italiano
Il design del pannello frontale può variare in base ai telai. Il modulo di un pannello frontale può consistere di: interruttore d’alimentazione, interruttore di ripristino, LED d’alimentazione, LED attività disco rigido, casse, eccetera. Quando si collega il modulo del pannello frontale a questo header, assicurarsi che l’assegnazione dei fi li e dei pin sia fatta corrispondere in modo appropriato.
Collettore casse telaio Collegare le casse del telaio a
(4-pin SPEAKER1)
(vedi p.2 Nr. 23)
questo collettore.
66
ASRock FM2A85X Extreme4 Motherboard
Page 67
LED di accensione Collegare il LED di accensione
(3-pin PLED1)
(vedi p.2 Nr. 26)
chassi per indicare lo stato di
alimentazione del sistema. Il
1
PLED+
PLED+
PLED-
LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).
Collettori Chassis ed alimentazione ventola Collegare i cavi della ventola ai
(4-pin CHA_FAN1)
(vedi p.2 Nr. 24)
corrispondenti connettori
facendo combaciare il cavo nero col pin di terra.
(3-pin CHA_FAN2)
(vedi p.2 Nr. 43)
(3-pin CHA_FAN3)
(vedi p.2 Nr. 44)
(3-pin PWR_FAN1)
(vedi p.2 Nr. 1)
Connettore ventolina CPU Collegare il cavo della ventolina
(4-pin CPU_FAN1)
(vedi p.2 Nr. 5)
terra.
FAN_SPEED_CONTROL
CPU a questo connettore e far
combaciare il fi lo nero al pin
CPU_FAN_SPEED
+12V
GND
1 2 3 4
Sebbene la presente scheda madre disponga di un supporto per ventola CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in grado di funzionare anche senza la funzione di controllo della velocità della ventola. Se si intende collegare la ventola CPU a 3 piedini al connettore della ventola CPU su questa scheda madre, collegarla ai piedini 1-3.
Piedini 1-3 collegati
Installazione della ventola a 3 piedini
(3-pin CPU_FAN2)
(vedi p.2 Nr. 6)
GND
+12V
CPU_FAN_SPEED
Italiano
ASRock FM2A85X Extreme4 Motherboard
67
Page 68
Connettore alimentazione ATX Collegare la sorgente
(24-pin ATXPWR1)
(vedi p.2 Nr. 9)
d’alimentazione ATX a questo
connettore.
12 124
13
Con questa scheda madre, c’è in dotazione un
12
24
connettore elettrico ATX a 24 pin, ma può funzionare lo stesso se si adotta un alimentatore ATX a 20 pin. Per usare l’alimentatore ATX a 20 pin, collegare l’alimentatore con il Pin 1 e il Pin 13.
Installazione dell’alimentatore ATX a 20 pin
Connettore ATX 12 V Collegare un alimentatore ATX
(8-pin ATX12V1)
(vedi p.2 Nr. 2)
12 V a questo connettore.
4 8
1 5
1
13
Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX 12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura elettrica 4-pin ATX 12V, prego collegare la presa elettrica
4 8
al Pin 1 e Pin 5.
Installazione elettrica 4-Pin ATX 12V
1 5
Collettore porta COM Questo collettore porta COM è
(9-pin COM1)
(vedi p.2 Nr. 32)
utilizzato per supportare il
modulo porta COM.
Italiano
Header HDMI_SPDIF Header HDMI_SPDIF, con
(2-pin HDMI_SPDIF1)
(vedi p.2 Nr. 33)
uscita audio SPDIF su scheda
HDMI VGA, consente al sistema di collegare dispositivi per TV digitale HDMI/proiettori/ LCD . Collegare il connettore HDMI_SPDIF della scheda VGA HDMI a questo header.
68
ASRock FM2A85X Extreme4 Motherboard
Page 69
1.5 Interruttori rapidi
Questa scheda madre ha tre interruttori rapidi: Interruttore di alimentazione, interrut­tore di reset e interruttore pulizia CMOS, che consentono agli utenti di accendere / spegnere rapidamente o cancellare i valori CMOS.
Interruttore
(PWRBTN) (vedi p.2 Nr. 22)
Interruttore di reset
(RSTBTN) (vedi p.2 Nr. 20)
Interruttore pulizia CMOS
(CLRCBTN) (vedi p.3 Nr. 14)
L’interruttore di alimentazione è un interruttore rapido che consente agli utenti di accendere/spegnere rapidamente il sistema.
L’interruttore di reset è un interruttore rapido che consente agli utenti di resettare rapidamente il sistema.
L’interruttore di pulizia CMOS è un interruttore rapido che consente agli utenti di cancellare velocemente i valori CMOS.
ASRock FM2A85X Extreme4 Motherboard
Italiano
69
Page 70
2. Informazioni sul BIOS
La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF fi le) contenuto nel cd di supporto.
3. Software di supporto e informazioni su
CD
Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 8 / 8 64­bit / 7 / 7 64-bit / VistaTM / Vista madre contiene i driver e utilità necessari a potenziare le caratteristiche della scheda. Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN” è attivata nel computer, apparirà automaticamente il Menù principale. Se il Menù principale non appare automaticamente, posizionarsi sul fi le “ASSETUP.EXE” nel CESTINO del CD di supporto e cliccare due volte per visualizzare i menù.
TM
64-bit. Il CD di supporto a corredo della scheda
Italiano
70
ASRock FM2A85X Extreme4 Motherboard
Page 71
1. Introducción
Gracias por su compra de ASRock FM2A85X Extreme4 placa madre, una placa de confi anza producida bajo el control de calidad estricto y persistente. La placa madre provee realización excelente con un diseño robusto conforme al compromiso de calidad y resistencia de ASRock. Esta Guía rápida de instalación contiene una introducción a la placa base y una guía de instalación paso a paso. Puede encontrar una información más detallada sobre la placa base en el manual de usuario incluido en el CD de soporte.
Porque las especifi caciones de la placa madre y el software de BIOS podrían ser actualizados, el contenido de este manual puede ser cambiado sin aviso. En caso de cualquier modifi cación de este manual, la versión actualizada estará disponible en el website de ASRock sin previo aviso. También encontrará las listas de las últimas tarjetas VGA y CPU soportadas en la página web de ASRock. Website de ASRock http://www.asrock.com Si necesita asistencia técnica en relación con esta placa base, visite nuestra página web con el número de modelo específi co de su placa. www.asrock.com/support/index.asp
1.1 Contenido de la caja
Placa base ASRock FM2A85X Extreme4 (Factor forma ATX) Guía de instalación rápida de ASRock FM2A85X Extreme4 CD de soporte de ASRock FM2A85X Extreme4 Cuatro cables de datos Serial ATA (SATA) (Opcional) Una protección I/O
ASRock le recuerda...
Para mejorar el rendimiento en Windows® 8 / 8 64 bits / 7 / 7 64 bits / Vis-
TM
ta
/ VistaTM 64 bits, es recomendable establecer la opción del BIOS de la confi guración de almacenamiento en el modo AHCI. Para obtener de- talles sobre la confi guración del BIOS, consulte el “Manual del usuario” que se encuentra en nuestro CD de soporte.
ASRock FM2A85X Extreme4 Motherboard
Español
71
Page 72
Español
1.2 Especifi cación
Plataforma - Factor forma ATX
- Todo diseño de Capacitor Sólido (condensadores de polímero conductor de alta calidad de fabricación 100% japonesa) Procesador - Admite procesadores de 100 W para zócalo FM2
- Diseño de fases de potencia 4 + 2
- Con soporte para tecnología Cool ‘n’ Quiet
- UMI-Link GEN2
Chipset - AMD A85X (Hudson-D4) Memoria - Soporte de Tecnología de Memoria de Doble Canal
- 4 x DDR3 DIMM slots
- Apoya DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/ 1333/1066/800 non-ECC, memoria de un-buffered
- Máxima capacidad de la memoria del sistema: 64GB
- Compatible con Intel
®
Extreme Memory Profi le (XMP)1.3/1.2
- Compatible con AMD Memory Profi le (AMP) Ranuras de - 2 x ranuras PCI Express 2.0 x16 Expansión (PCIE2: modo x16; PCIE4: modo x4)
- 2 x ranuras PCI Express 2.0 x1
- 3 x ranuras PCI
- Admite CrossFireX
TM
cuádruple de AMD, CrossFireXTM y
tarjeta gráfi ca dual VGA OnBoard - Tarjeta gráfi ca AMD Radeon HD 7000
- DirectX 11, Pixel Shader 5.0
- 2GB de Memoria máxima compartida
- Tres opciones de salida VGA: D-Sub, DVI-D y HDMI
- Admite HDMI 1.4a con una resolución máxima de 1920x1200 a 60 Hz
- Admite Dual-link DVI con una resolución máxima de 2560x1600 a 75 Hz
- Admite D-Sub con una resolución máxima de 1920x1600 a 60 Hz
- Admite Sincronización automática entre audio y vídeo, Deep Color (12 bpc), xvYCC y HBR (audio de alta tasa de bits) con HDMI (se necesita un monitor compatible con HDMI)
- Admite la función 3D estereoscópica Blu-ray con HDMI 1.4a
- Admite AMD Steady Video
TM
2.0: Nueva capacidad de pospro cesamiento de vídeo para reducción automática de oscila ciones en vídeo doméstico y en línea
TM
de AMD
72
ASRock FM2A85X Extreme4 Motherboard
Page 73
- Admite la función HDCP con puertos DVI y HDMI
- Apoya la reproducción de Blu-rayo de 1080p (BD) / HD-DVD con puertos DVI y HDMI Audio - 7.1 CH HD Audio con Protección de Contenido (Realtek ALC892 Audio Codec)
- Compatible con audio Blu-ray de alta calidad
TM
- Compatible con THX TruStudio LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Soporta Wake-On-LAN
- Admite detección de conexión de cable LAN
- Compatible con Ethernet 802.3az de bajo consumo energético
- Compatible con PXE Entrada/Salida I/O Panel de Panel - 1 x puerto de ratón/teclado PS/2 Trasero - 1 x Puerto D-Sub
- 1 x Puerto DVI-D
- 1 x puerto HDMI
- 1 x puerto de salida óptica SPDIF
- 2 x puertos USB 2.0 predeterminados
- 1 x Conector eSATA3
- 6 x puertos USB 3.0 predeterminados
- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/ ENLACE y LED de VELOCIDAD)
- 1 x conmutador de borrado de memoria CMOS
- Conexión de audio: Altavoz trasero / Central/Bajos / Entrada de línea / Altavoz frontal / Micrófono SATA 3 - 7 x conectores SATA3 de 6,0 Gb/s compatibles con funciones RAID (RAID 0, RAID 1, RAID 5 y RAID 10), NCQ, AHCI y de “conexión en caliente” USB 3.0 - 2 x puertos USB 3.0 traseros de AMD A85X (Hudson-D4), compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s
- 4 x puertos USB 3.0 traseros de Etron EJ188 compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s
- 1 x cabecera USB 3.0 delantera (compatible con 2 puertos USB 3.0) de AMD A85X (Hudson-D4), compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s Conectores - 7 x conexiones SATA3, admiten una velocidad de transferencia de datos de hasta 6,0Gb/s
- 1 x Cabezal de Módulo Infrarrojos
Español
ASRock FM2A85X Extreme4 Motherboard
73
Page 74
Español
- 1 x Base de conexiones del módulo de infrarrojos para el
consumidor
- 1 x En-tête de port COM
- 1 x cabecera HDMI_SPDIF
- 1 x cabecera de indicador LED de encendido
- 2 x Conector de ventilador de CPU (1 x 4-pin, 1 x 3-pin)
- 3 x Conector de ventilador de chasis (1 x 4-pin, 2 x 3-pin)
- 1 x Conector de ventilador de alimentacion (3-pin)
- 24-pin cabezal de alimentación ATX
- 8-pin conector de ATX 12V power
- Conector de audio de panel frontal
- 3 x Cabezal USB 2.0 (admite 6 puertos USB 2.0 adicionales)
- 1 x Cabezal USB 3.0 (admite 2 puertos USB 3.0 adicionales)
- 1 x Dr. Debug (indicador LED de avería de 7 segmentos)
- 1 x conmutador de encendido con indicador LED
- 1 x conmutador de reinicio con indicador LED BIOS - 64Mb AMI BIOS legal UEFI AMI compatible con GUI
- Soporta “Plug and Play”
- ACPI 1.1 compliance wake up events
- Soporta “jumper free setup”
- Soporta SMBIOS 2.3.1
- Múltiple ajuste deDRAM, APU PCIE VDDP, CPU y CPU NB/GFX Voltage CD de soport - Controladores, Utilerías, Software de Anti Virus (Versión de prueba), Prueba de CyberLink MediaEspresso 6.5, Google Chrome Browser y Toolbar Monitor Hardware - Sensibilidad a la temperatura del procesador
- Sensibilidad a la temperatura de la placa madre
- Taquimetros de los ventiladores del procesador y del CPU / chasis / alimentacion
- Ventilador silencioso del procesador
- Control de ajuste de la velocidad del ventilador de la CPU y el chasis
- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore OS - En conformidad con Microsoft
®
Windows® 8 / 8 64 bits / 7 /
7 64 bits / VistaTM / VistaTM 64 bits Certi caciones - FCC, CE, WHQL
- Cumple con la directiva ErP/EuP (se requiere una fuente de alimentación que cumpla con la directiva ErP/EuP)
74
ASRock FM2A85X Extreme4 Motherboard
Page 75
* Para más información sobre los productos, por favor visite nuestro sitio web: http://www.asrock.com
1.3 Setup de Jumpers
La ilustración muestra como los jumpers son confi gurados. Cuando haya un jumper- cap sobre los pins, se dice gue el jumper está “Short”. No habiendo jumper cap sobre los pins, el jumper está “Open”. La ilus­tración muesta un jumper de 3 pins cuyo pin 1 y pin 2 están “Short”.
Jumper Setting
Limpiar CMOS
(CLRCMOS1, jumper de 3 pins) (ver p.2, No. 27)
Nota:
Valor predetermi­nado
Restablecimiento de
la CMOS
CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los parámetros del sistema y restablecer la confi guración predeterminada de los mismos, apague el equipo y desenchufe el cable de alimentación de la toma de corriente eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perfi l predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se borrará si la batería CMOS se quita.
para
El conmutador Borrar CMOS tiene la misma función que el puente Borrar CMOS.
ASRock FM2A85X Extreme4 Motherboard
Español
75
Page 76
1.4 Cabezales y Conectores en Placas
Los conectores y cabezales en placa NO son puentes. NO coloque las cubiertas de los puentes sobre estos cabezales y conectores. El colocar cubiertas de puentes sobre los conectores y cabezales provo­cará un daño permanente en la placa base.
Conexiones de serie ATA3 Estas siete conexiones de
(SATA3_1: vea p.2, N. 13)
(SATA3_2: vea p.2, N. 12)
(SATA3_3: vea p.2, N. 14)
(SATA3_4: vea p.2, N. 15)
(SATA3_5: vea p.2, N. 19)
(SATA3_6: vea p.2, N. 16)
(SATA3_7: vea p.2, N. 17)
Cable de datos de Cualquier extremo del cable de serie ATA (SATA) los datos de SATA puede ser
(Opcional)
conectado con el disco duro de SATA3 o el conectador de SATA3 en esta placa base.
serie ATA3 (SATA3) admiten cables SATA para dispositivos de almacenamiento internos. La interfaz SATA3 actual permite una velocidad de transferencia de 6.0 Gb/s.
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
Español
76
Cabezal USB 2.0 Además de dos puertos
(9-pin USB3_4)
(vea p.2, N. 30)
USB 2.0 predeterminados en el
panel de E/S, hay tres bases de conexiones USB 2.0 en esta placa base. Cada una de estas bases de conexiones
(9-pin USB5_6)
(vea p.2, N. 29)
(9-pin USB7_8) (vea p.2, N. 28)
admite dos puertos USB 2.0.
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-3
P-6
P+6
GND
DUMMY
GND
P+5
P-5
P-8
P+8
GND
DUMMY
GND
P+7
P-7
ASRock FM2A85X Extreme4 Motherboard
Page 77
Cabezal USB 3.0 Además de seis puertos 3.0
(19-pin USB3_7_8)
(vea p.2, N. 10)
cabecera USB 3.0 en esta placa base. Esta cabecera USB
3.0 admiten dos puertos USB
3.0.
predeterminados situados en el
panel E/S, encontrará una
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
Cabezal de Módulo Infrarrojos Este cabezal soporta un
(5-pin IR1)
módulo infrarrojos de
(vea p.2, N. 25)
transmisión y recepción
wireless opcional.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Base de conexiones del módulo de Esta base de conexiones se infrarrojos para el consumidor puede utilizar para conectar
(4-pin CIR1)
(vea p.2, N. 31)
Conector de audio de Este es una interface para panel frontal cable de audio de panel frontal
(9-pin HD_AUDIO1)
(vea p.2, N. 34)
Audio.
1. El Audio de Alta Defi nición soporta la detección de conector, pero el cable de panel en el chasis debe soportar HDA para operar correctamente. Por favor, siga las instrucciones en nuestro manual y en el manual de chasis para instalar su sistema.
2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido del panel frontal de la siguiente manera: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L. C. Conecte Ground (GND) a Ground (GND).
E. Activación del micrófono frontal. En sistemas operativos Windows Vista Acceda a la fi cha “FrontMic” (Micrófono frontal) del panel de control Realtek. Ajuste la posición del control deslizante “Recording Volume” (Volumen de grabación).
receptor remoto.
GND
PRESENCE#
MIC_RET
OUT_RET
que permite conexión y control
TM
64-bit:
1
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT2_L
®
8 / 8 64-bit / 7 / 7 64-bit / VistaTM /
conveniente de apparatos de
D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No necesitará conectarlos al panel de sonido AC’97.
ASRock FM2A85X Extreme4 Motherboard
Español
77
Page 78
Cabezal de panel de sistema Este cabezar acomoda varias
(9-pin PANEL1)
(vea p.2, N. 21)
Conecte el interruptor de alimentación, el interruptor de restablecimiento y el indicador de estado del sistema situados en el chasis con esta cabecera en función de las siguientes asignaciones de contacto. Preste atención a los contactos positivos y negativos antes de conectar los cables.
PWRBTN (interruptor de alimentación):
RESTABLECER (interruptor de restablecimiento):
PLED (LED de alimentación del sistema):
HDLED (LED de actividad del disco duro):
dunciones de panel frontal de
sistema.
Conecte el interruptor de encendido situado en el panel frontal del chasis. Puede confi gurar la forma de apagar su sistema mediante el interruptor de alimentación.
Conecte el interruptor de restablecimiento situado en el panel frontal del chasis. Pulse el interruptor de restablecimiento para restablecer el equipo si se bloquea y no se reinicia con normalidad.
Conecte el indicador de estado de alimentación situado en el panel frontal del chasis. El LED se enciende cuando el sistema esté en funcionamiento. El LED parpadea cuando el sistema se encuentre en estado de suspensión S1. El LED se apaga cuando el sistema se encuentre en estado de suspensión S3/S4 o se apaga (S5).
Conecte el LED de actividad de disco duro situado en el panel frontal del chasis. El LED se enciende cuando el disco duro esté leyendo o escribiendo datos.
Español
78
Es posible que el diseño del panel frontal varíe en función del chasis. Un módulo del panel frontal consiste principalmente de interruptor de alimentación, interruptor de restablecimiento, LED de alimentación, LED de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel frontal del chasis a esta cabecera, asegúrese de que las asignaciones de cables y las asignaciones de contactos coincidan correctamente.
ASRock FM2A85X Extreme4 Motherboard
Page 79
Cabezal del altavoz del chasis Conecte el altavoz del chasis a
(4-pin SPEAKER1)
(vea p.2, N. 23)
su cabezal.
Cabecera de indicador LED de encendido Conecte el indicador LED de
(3-pin PLED1)
(vea p.2, N. 26)
estado de encendido del
encendido del chasis a esta
cabecera para conocer el
1
PLED+
PLED+
PLED-
sistema. El indicador LED se encenderá si el sistema se encuentra en funcionamiento. El indicador LED parpadeará en el estado S1. El indicador LED se apagará en los estados S3/S4 o S5 (apagado).
Conectores de ventilador de chasis y alimentación
(4-pin CHA_FAN1)
(vea p.2, N. 24)
Por favor, conecte los cables del ventilador a los conectores de ventilador, haciendo coincidir el cable negro con la patilla de masa.
(3-pin CHA_FAN2)
(vea p.2, N. 43)
(3-pin CHA_FAN3)
(vea p.2, N. 44)
(3-pin PWR_FAN1)
(vea p.2, N. 1)
Conector del ventilador Conecte el cable del ventilador de la CPU de la CPU a este conector y
(4-pin CPU_FAN1)
(vea p.2, N. 5)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
+12V
haga coincidir el cable negro
con el conector de tierra.
GND
1 2 3 4
Español
ASRock FM2A85X Extreme4 Motherboard
79
Page 80
Aunque esta placa base proporciona compatibilidad para un ventilador (silencioso) de procesador de 4 contactos, el ventilador de procesador de 3 contactos seguirá funcionando correctamente incluso sin la función de control de velocidad del ventilador. Si pretende enchufar el ventilador de procesador de 3 contactos en el conector del ventilador de procesador de esta placa base, conéctelo al contacto 1-3.
Contacto 1-3 conectado
Instalación del ventilador de 3 contactos
Español
(3-pin CPU_FAN2)
(vea p.2, N. 6)
Cabezal de alimentación ATX Conecte la fuente de
(24-pin ATXPWR1)
(vea p.2, N. 9)
A pesar de que esta placa base incluye in conector de alimentación ATX de 24 pins, ésta puede funcionar
GND
+12V
CPU_FAN_SPEED
12 124
alimentación ATX a su cabezal.
13
12
24
incluso si utiliza una fuente de alimentación ATX de 20 pins tradicional. Para usar una fuente de alimentación ATX de 20 pins, por favor, conecte su fuente de alimentación usando los Pins 1 y 13.
Instalación de una Fuente de Alimentación ATX de 20 Pins
1
13
Conector de ATX 12V power Tenga en cuenta que es
(8-pin ATX12V1)
(vea p.2, N. 2)
corriente con el enchufe ATX
necesario conectar este
conector a una toma de
4 8
1 5
12V, de modo que proporcione sufi ciente electricidad. De lo contrario no se podrá encender.
Aunque esta placa base proporciona un conector de energía de 8-pin ATX 12V, puede todavía trabajar si usted adopta un fuente tradicional de energía de 4-pin ATX 12V. Para usar el fuente de energía de 4-pin ATX 12V, por favor conecte su fuente de energía junto con Pin 1 y Pin 5.
4 8
80
Instalación de Fuente de Energía de 4-Pin ATX 12V
ASRock FM2A85X Extreme4 Motherboard
1 5
Page 81
Cabezal del puerto COM Este cabezal del puerto COM
(9-pin COM1)
(vea p.2, N. 32)
se utiliza para admitir un
módulo de puerto COM.
Cabecera HDMI_SPDIF Cabecera HDMI_SPDIF. Ofrece
(HDMI_SPDIF1 de 2 pin)
(vea p.2, N. 33)
una salida SPDIF la tarjeta
VGA HDMI, permite al sistema conectarse a dispositivos de TV Digital HDMI / proyectores / Dispositivos LCD. Conecte el conector HDMI_SPDIF de la tarjeta VGA HDMI a esta cabecera.
ASRock FM2A85X Extreme4 Motherboard
Español
81
Page 82
1.5 Conmutadores rápidos
Esta placa base dispone de tres conmutadores rápidos: conmutador de encen­dido, conmutador de reinicio y conmutador de borrado de memoria CMOS. Dichos conmutadores permiten al usuario encender / apagar o reiniciar el sistema, o bien borrar el contenido de la memoria CMOS.
Conmutador de encendido
(PWRBTN) (vea p.2, N. 22)
Conmutador de reinicio
(RSTBTN) (vea p.2, N. 20)
Conmutador de borrado de memoria CMOS
(CLRCBTN) (vea p.3, N. 14)
El conmutador de reinicio es un conmutador rápido que permite al usuario reiniciar rápidamente el sistema.
El conmutador de borrado de memoria CMOS es un conmutador rápido que permite al usuario borrar rápidamente el contenido de la memoria CMOS.
El conmutador de encendido es un conmutador rápido que permite al usuario encender / apagar rápidamente el sistema.
Español
82
ASRock FM2A85X Extreme4 Motherboard
Page 83
2. BIOS Información
El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up (POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> + <Borrar>, o apretando el botón Reset en el panel del ordenador. Para información detallada sobre como confi gurar la BIOS, por favor refi érase al Manual del Usuario (archivo PDF) contenido en el CD.
3. Información de Software Support CD
Esta placa-base soporta diversos tipos de sistema operativo Windows®: 8 / 8 64 bits / 7 / 7 64 bits / Vista base trae todos los drivers y programas utilitarios para instalar y confi gurar la placa- base. Para iniciar la instalación, ponga el CD en el lector de CD y se desplegará el Menú Principal automáticamente si «AUTORUN» está habilitado en su computado­ra. Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el archivo “ASSETUP.EXE” para iniciar la instalación.
TM
/ Vista
TM
64 bits. El CD de instalación que acompaña la placa-
ASRock FM2A85X Extreme4 Motherboard
Español
83
Page 84
1. Введение
Благодарим вас за покупку материнской платы ASRock FM2A85X Extreme4 надежной материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock жесткими требованиями к качеству. Она обеспечивает превосходную производительность и отличается отличной конструкцией, которые отражают приверженность ASRock качеству и долговечности. Данное руководство по быстрой установке включает вводную информацию о материнской плате и пошаговые инструкции по ее установке. можно найти в руководстве пользователя на компакт-диске поддержки.
Спецификации материнской платы и программное обеспечение BIOS иногда изменяются, поэтому содержание этого руководства может обновляться без уведомления. В случае любых модификаций руководства его новая версия будет размещена на веб-сайте ASRock без специального уведомления. Кроме того, самые свежие списки поддерживаемых модулей памяти и процессоров можно найти на сайте ASRock. Адрес веб-сайта ASRock http://www.asrock.com При необходимости технической поддержки по вопросам данной материнской платы посетите наш веб-сайт для получения информации об используемой модели. www.asrock.com/support/index.asp
1.1 Комплектность
Материнская плата ASRock FM2A85X Extreme4 (форм-фактор ATX) Руководство по быстрой установке ASRock FM2A85X Extreme4 Компакт-диск поддержки ASRock FM2A85X Extreme4
4 x кабель данных Serial ATA (SATA) (дополнительно) 1 x I/O Щит Группы ввода / вывода
Более подробные сведения о плате
Русский
84
ASRock напоминает...
Для обеспечения максимальной производительности ОС Windows 8 / 8 64-bit / 7 / 7 64-bit / Vista BIOS выбрать для параметра Storage Confi guration (Конфигурация
запоминающего устройства) режим AHCI. Подробные сведения о настройке BIOS см. в руководстве пользователя на прилагаемом компакт-диске.
TM
/ VistaTM 64-bit рекомендуется в
ASRock FM2A85X Extreme4 Motherboard
®
Page 85
1.2 Спецификации
Платформа - форм-фактор ATX
- Весь Твердый Конденсаторный проект (100% японские высококачественные конденсаторы на основе проводящих полимеров) Процессор - Поддерживаются процессоры для гнезда Socket FM2 с потребляемой мощностью до 100 Вт
- Технология 4 + 2 Power Phase Design
- Поддержка технологии AMD Cool ‘n’ Quiet
- UMI-Link GEN2 Набор микросхем - AMD A85X (Hudson-D4) Память - Поддержка технологии Dual Channel DDR3 Memory Technology (см. ОСТОРОЖНО, пункт 1)
- 4 x гнезда DDR3 DIMM
- Поддержите DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/1333/ 1066/800 не- ECC, безбуферная память
- Mакс. 64 Гб
- поддержка профиля Intel
®
Extreme Memory Profi le (XMP)1.3/1.2
- поддержка профиля AMD Memory Profi le (AMP)
Гнезда - 2 x гнезда PCI Express 2.0 x16 расширения (PCIE2: режим x16; PCIE4: режим x4)
- 2 x гнезда PCI Express 2.0 x1
- 3 x гнезда PCI
- Поддерживаются режимы AMD Quad CrossFireX двойные видеокарты Графика - Видеоадаптер AMD Radeon HD 7000
- Поддержка DirectX 11, Pixel Shader 5.0
- Макс. объем разделяемой памяти 2GB
- Три VGA-выхода: D-Sub, DVI-D и HDMI
- Поддержка HDMI 1.4a с максимальным разрешением до 1920х1200 @ 60 Гц
- Поддержка Dual-link DVI с максимальным разрешением до 2560х1600 @ 75 Гц
- Поддержка D-Sub с максимальным разрешением до 1920х1600 @ 60 Гц
- Поддержка Auto Lip Sync, Deep Color (12 бит на цветовой канал), xvYCC и HBR (High Bit Rate Audio) через HDMI (необходим монитор с разъемом
HDMI)
- Поддержка стандарта Blu-ray Stereoscopic 3D со спецификацией HDMI 1.4a
- Поддержка технологии AMD Steady Video постобработки видеоизображения для автоматического устранения дрожания при просмотре домашних и онлайновых видеозаписей
- Поддержка функции HDCP через разъемы DVI и HDMI
- Подержат Blu-луч 1080p (КОММУТАЦИОННАЯ ДОСКА) / воспроизведение HD-DVD через разъемы DVI и HDMI
TM
TM
, CrossFireXTM и
TM
2.0: новая функция
Русский
ASRock FM2A85X Extreme4 Motherboard
85
Page 86
Русский
Аудиосистема - 7.1 CH HD Аудио HD с Довольной Защитой (Кодер-декодер Аудио Realtek ALC892)
- Поддержка Premium Blu-ray audio
- Поддержка технологии THX TruStudio ЛВС - PCIE x 1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- поддержка Wake-On-LAN
- Поддержка определения кабеля ЛВС
- Поддержка энергосберегающего интерфейса Ethernet 802.3az
- Поддержка PXE Разъемы ввода- I/O Panel вывода на задней - 1 x порт мыши/клавиатуры PS/2 панели - 1 x D-Sub порт
- 1 x DVI-D порт
- 1 x HDMI порт
- 1 x порт Optical SPDIF Out
- 2 x порта USB 2.0 на задней панели в стандартной конфигурации
- 1 x eSATA3 порт
- 6 x порта USB 3.0 на задней панели в стандартной конфигурации
- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор ACT/LINK и
- 1 x кнопка Clear CMOS
- Соединитель звуковой подсистемы: тыльная колонка / центральная / субвуфер / линейный вход / передняя колонка / микрофон SATA 3 - 7 x разъема SATA3 6,0 Гбит/с, поддержка функций RAID (RAID 0, RAID 1, RAID 5 и RAID 10), NCQ, AHCI и «горячего подключения» USB 3.0 - 2 x задних порта USB 3.0 на контроллере AMD A85X (Hudson-D4) с поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с
- 4 x задних порта USB 3.0 на контроллере Etron EJ188 с поддержкой интерфейсов USB 1.1/2.0/3.0 и данных до 5 Гбит/с
- 1 x передний разъем USB 3.0 (поддерживает 2 порта USB 3.0) на контроллере AMD A85X (Hudson-D4) с поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с
Колодки и - 7 x разъема SATA3 6,0 Гбит/с плате - 1 x Колодка инфракрасного модуля
- 1 x
- 1 x Колодка COM
- 1 x Колодка HDMI_SPDIF
- 1 x разъем Power LED
- 2 x соединитель CPU FAN (1 x 4-контактный, 1 x 3-контактный)
- 3 x соединитель Chassis FAN (1 x 4-контактный, 2 x 3-контактный)
- 1 x соединитель Power FAN (3-контактный)
- 24-контактный Колодка питания ATX
индикатор SPEED)
Датчик пользовательского инфракрасного модуля
TM
скорости передачи
86
ASRock FM2A85X Extreme4 Motherboard
Page 87
- 8-контактный Разъем ATX 12 В
- Аудиоразъем передней панели
- 3 x Колодка USB 2.0 (одна колодка для поддержки 6 дополнительных портов USB 2.0
- 1 x Колодка USB 3.0 (одна колодка для поддержки 2 дополнительных портов USB 3.0)
- 1 x Dr. Debug (7-сегментный ЖК-дисплей)
- 1 x кнопка Power Switch со светодиодом
- 1 x кнопка Reset Switch со светодиодом BIOS - 64Mb AMI UEFI Legal BIOS с поддержкой rpaфичеckoro интеpфeйca поль зователя
- поддержка “Plug and Play”
- ACPI 1.1, включение по событиям
- поддержка режима настройки
- поддержка SMBIOS 2.3.1
- Регулировка напряжений DRAM, APU PCIE VDDP, CPU и CPU NB/GFX Компактдиск - Драйверы, Утилиты, Антивирус (пробная версия), Пробная версия поддержки программы CyberLink MediaEspresso 6.5, Google Chrome Browser и Toolbar Контроль - Датчики температуры процессора оборудо- - Датчики температуры корпуса вания - Тахометры вентиляторов CPU/Chassis/Power FAN
- Бесшумный вентилятор ЦП блока
- Мультиконтроль скорости вентилятора ЦП/Шасси
- Контроль напряжения: +12V, +5V, +3.3V, Vcore Операцион - Совместимость с Microsoft Vista ные системы - FCC, CE, WHQL Сертификаты - Совместимость с ErP/EuP Ready (требуется блок питания совместимый с ErP/EuP) * Для детальной информации продукта, пожалуйста посетите наш вебсайт: http://www.asrock.com
TM
/ Поддержка 64-разрядной версии VistaTM
без перемычек
®
Windows® 8 / 8 64-bit / 7 / 7 64-bit /
ASRock FM2A85X Extreme4 Motherboard
Русский
87
Page 88
1.3 Установка перемычек
Конфигурация перемычек иллюстрируется на рисунке. Когда перемычка надета на контакты, они называются “замкнутыми” (short). Если на контактах перемычки нет, то они называются “разомкнутыми” (open). На иллюстрации показана 3-контактная перемычка, у которой контакты 1 и 2 замкнуты.
Перемычка Установка Описание
Очистка CMOS
(CLRCMOS1, 3-контактная перемычка) (см. стр. 2, п. 27)
Стандартные Очистка CMOS
Русский
Примечание.
Контактная колодка CLRCMOS1 позволяет очистить данные CMOS. Для очистки данных и восстановления заводских системных параметров сначала выключите компьютер и отсоедините сетевую вилку кабеля питания от электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5 секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не производите очистку CMOS непосредственно после обновления BIOS. Если необходимо очистить CMOS сразу же после перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а затем завершить ее работу. Примите во внимание, что пароль, дата, время, профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес будут очищены только тогда, когда будет извлечена из своего гнезда батарейка
CMOS.
Переключатель Clear CMOS работает так же, как перемычка Clear CMOS.
окончания обновления BIOS, то,
88
ASRock FM2A85X Extreme4 Motherboard
Page 89
1.4 Колодки и разъемы на плате
Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки на эти колодки и разъемы – это приведет к необратимому повреждению материнской платы!
Разъемы Serial ATA3 семь соединителя Serial ATA3
(SATA3_1, см. стр. 2, п. 13) (SATA3_2, см. стр. 2, п. 12) (SATA3_3, см. стр. 2, п. 14) (SATA3_4, см. стр. 2, п. 15) (SATA3_5, см. стр. 2, п. 19) (SATA3_6, см. стр. 2, п. 16) (SATA3_7, см. стр. 2, п. 17)
данных до \ 6,0 Гбит/с.
Информационный Информационный кабель кабель Serial ATA (SATA) интерфейса SATA3 не является
(дополнительно)
направленным. Любой из его соединителей может быть подключен либо к жесткому диску интерфейса SATA3 либо к материнской плате.
предназначаются для подключения внутренних устройств хранения с
использованием нтерфейсных кабелей SATA3. В настоящее время интерфейс SATA
допускает скорость передачи
SATA3_7 SATA3_4 SATA3_2
SATA3_5
SATA3_6 SATA3_3 SATA3_1
Колодка USB 2.0 Помимо два стандартных
(9-контактный USB3_4) (см. стр. 2, п. 30)
портов USB 2.0 на панели ввода-
вывода, на данной материнской плате предусмотрено три разъема USB 2.0. Каждый разъем USB 2.0 поддерживает два порта USB 2.0.
(9-контактный USB5_6) (см. стр. 2, п. 29)
(9-контактный USB7_8) (см. стр. 2, п. 28)
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
USB_PWR
1
USB_PWR
P-4
P+4
GND
DUMMY
GND
P+3
P-3
P-6
P+6
GND
DUMMY
GND
P+5
P-5
P-8
P+8
GND
DUMMY
GND
P+7
P-7
ASRock FM2A85X Extreme4 Motherboard
Русский
89
Page 90
Колодка USB 3.0 Помимо шесть стандартных
(19-контактный USB3_7_8) (см. стр. 2, п. 10)
плате предусмотрен один разъем USB 3.0. Этот разъем USB 3.0 поддерживает два порта USB 3.0.
портов USB 3.0 на панели ввода-
Vbus
IntA_P7_SSRX-
IntA_P7_SSRX+
GND
IntA_P7_SSTX-
IntA_P7_SSTX+
GND
IntA_P7_D-
IntA_P7_D+
VbusVbus
IntA_P8_SSRX-
IntA_P8_SSRX+
GND
IntA_P8_SSTX-
IntA_P8_SSTX+
GND
IntA_P8_D-
IntA_P8_D+
DUMMY
вывода, на данной материнской
Русский
Колодка инфракрасного модуля Данная колодка позволяет
(5-контактный IR1) (см. стр. 2, п. 25)
подключить дополнительный
модуль беспроводного инфракрасного приемопередатчика.
IRTX
+5VSB
DUMMY
1
GND
IRRX
Датчик пользовательского инфракрасного модуля Датчик можно использовать для
(4-контактный CIR1) (см. стр. 2, п. 31)
Аудиоразъем передней Этот интерфейс предназначен панели для присоединения
(9-контактный HD_AUDIO1) (см. cтр. 2, п. 34)
подключение аудиоустройств и управление ими.
подключения дистанционный
приемник.
GND
PRESENCE#
MIC_RET
MIC2_R
MIC2_L
J_SENSE
OUT2_R
OUT_RET
OUT2_L
аудиокабеля передней панели,
обеспечивающего удобное
1
1. Система High Defi nition Audio поддерживает функцию автоматического обнаружения разъемов (Jack Sensing), однако для ее правильной pаботы кабель панели в корпусе должен поддерживать HDA. При сборке системы следуйте инструкциям, приведенным в нашем руководстве и руководстве пользователя для корпуса.
2. Если вы используете аудиопанель AC’97, подключите ее к колодке аудиоинтерфейса передней панели следующим образом: A. Подключите
выводы Mic_IN (MIC) к контактам MIC2_L. B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а выводы Audio_L (LIN) к контактам OUT2_L. C. Подключите выводы Ground (GND) к контактам Ground (GND).
D. Контакты MIC_RET и OUT_RET предназначены только для аудиопанели HD. При использовании аудиопанели AC’97
подключать их не нужно.
E. Процедура активации микрофона приведена ниже.
90
ASRock FM2A85X Extreme4 Motherboard
Page 91
Для ОС Windows® 8 / 8 64-бита / 7 / 7 64-бита, VistaTM / VistaTM 64-бита: Перейдите к вкладке «FrontMic» (Передний микрофон) в панели управления Realtek. Отрегулируйте уровень «Recording Volume» (Громкость записи).
Колодка системной панели Данная колодка обеспечивает
(9-контактный PANEL1) (см. стр. 2, п. 21)
Подключите к этому разъему кнопку питания, кнопку сброса и индикатор состояния системы на корпусе в соответствии с указанным ниже назначением контактов. При подключении кабелей необходимо соблюдать полярность положительных и отрицательных контактов.
PWRBTN (кнопка питания):
Подключите к этим контактам кнопку питания на передней панели корпуса. Способ выключения системы можно настроить.
RESET (кнопка сброса):
Подключите к этим контактам кнопку сброса на передней панели корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если компьютер «завис» и нормальную перезагрузку выполнить не удается.
PLED (индикатор питания системы):
Подключите к этим контактам индикатор состояния питания на передней панели работает. Индикатор мигает, когда система находится в режиме ожидания S1. Этот индикатор не светится, когда система находится в режиме ожидания S3 или S4, либо выключена (S5).
HDLED (индикатор активности жесткого диска):
Подключите к этим контактам индикатор активности жесткого диска на передней панели корпуса. Этот индикатор светится, осуществляется считывание или запись данных на жестком диске.
работу нескольких функций
передней панели системы.
с помощью кнопки питания
корпуса. Этот индикатор светится, когда система
когда
Конструкция передней панели может различаться в зависимости от корпуса. Модуль передней панели в основном состоит из кнопки питания, кнопки сброса, индикатора питания, индикатора активности жесткого диска, динамика и т.п. При подключении к этому разъему модуля передней панели корпуса подключаются к соответствующим контактам.
удостоверьтесь, что провода
ASRock FM2A85X Extreme4 Motherboard
Русский
91
Page 92
Колодка динамика корпуса Подключите к этой колодке
(4-контактный SPEAKER1) (см. стр. 2, п. 23)
кабель от динамика на корпусе
компьютера.
разъем Power LED Подключите индикатор Power LED
(3-контактный PLED1) (см. стр. 2, п. 26)
светодиод продолжит мигать в
к этому разъему для отображения
статуса питания системы. Этот
1
PLED+
PLED+
PLED-
режиме S1. Светодиод будет выключен в режимах S3/S4 или S5 (система выключена).
Русский
Chassis и Power Fan-соединители
(4-контактный CHA_FAN1) (см. стр. 2, п. 24)
Подключите кабели вентилятора к соединителям и присоедините черный шнур к штырю заземления.
(3-контактный CHA_FAN2) (см. стр. 2, п. 43)
(3-контактный CHA_FAN3) (см. стр. 2, п. 44)
(3-контактный PWR_FAN1) (см. стр. 2, п. 1)
Разъем вентилятора Подключите к этому разъему процессора кабель вентилятора процессора
(4-контактный CPU_FAN1) (см. стр. 2, п. 5)
FAN_SPEED_CONTROL
CPU_FAN_SPEED
так, чтобы черный провод
GND
+12V
соответствовал контакту земли.
1 2 3 4
Данная материнская плата поддерживает вентиляторы процессора с 4-контактным разъемом (функция тихого режима вентилятора), однако вентиляторы с 3-контактным разъемом также будут успешно работать, хотя функция управления скоростью вращения вентилятора окажется недоступной. Если вы хотите подключить вентилятор процессора с 3-контактным разъемом к разъему вентилятора процессора на данной материнской плате,
для этого
следует использовать контакты 1-3.
Контакты 1-3 подключены
Установка вентилятора с 3-контактным разъемом
92
ASRock FM2A85X Extreme4 Motherboard
Page 93
(3-контактный CPU_FAN2) (см. стр. 2, п. 6)
GND
+12V
CPU_FAN_SPEED
Колодка питания ATX Подключите к этой колодке
(24-контактный ATXPWR1) (см. стр. 2, п. 9)
кабель питания ATX.
Несмотря на то, что эта материнская плата предусматр- ивает 24-штыревой разъем питания ATX, работа будет
12 124
13
12
продолжаться, даже если адаптируется традиционный 20-штыревой разъем питания ATX. Для использования 20-штыревого разъема питания ATX вставьте источник питания вместе со штекером 1 и штекером 13.
Установка 20-штыревого разъема питания ATX
1
Колодка питания 12V-ATX Обратите внимание, что к этому
(8-контактный ATX12V1) (см. стр. 2, п. 2)
разъему необходимо
подключить вилку блока питания
ATX 12 В, чтобы обеспечить
4 8
1 5
достаточную мощность электропитания. В противном случае включение системы будет невозможно.
Хотя эта объединительная плата обеспечивает ATX с 8 булавками 12V
соединитель власти, это может все еще работать, если Вы принимаете традиционный ATX с 4-Pin 12V электропитание. Чтобы использовать электропитание ATX с 4-Pin, пожалуйста включите ваше электропитание наряду с Булавкой 1 и Прикрепите 5.
4 8
24
13
ATX С 4-Pin 12V Установка Электропитания
1 5
Колодка COM-порта Данная колодка COM-порта
(9-контактный COM1) (см. стр. 2, п. 32)
позволяет подключить модуль
порта COM.
ASRock FM2A85X Extreme4 Motherboard
Русский
93
Page 94
Колодка HDMI_SPDIF Колодка HDMI_SPDIF
(2-контактный HDMI_SPDIF1) (см. стр. 2, п. 33)
HDMI, что позволяет подключать к системе цифровые телевизоры, проекторы или жидкокристаллические панели HDMI. Соедините эту колодку с разъемом HDMI_SPDIF на VGA­ карте HDMI.
аудиосигнала на VGA-карту
обеспечивает подачу выходного
1.5 Быстрое переключение
На этой материнской плате есть три кнопки для ускорения работы: кнопка питания, кнопка перезагрузки и кнопка для очистки CMOS, которые позволяют пользователям быстро включить/выключить или перезагрузить компьютер, сбросить установки CMOS, соответственно.
Русский
Power Switch
(PWRBTN) (см. стр. 2, п. 22)
Reset Switch
(RSTBTN) (см. стр. 2, п. 20)
Clear CMOS Switch
(CLRCBTN) (см. стр. 3, п. 14)
Кнопка Power Switch позволяет быстро включить или выключить систему.
Кнопка Reset Switch позволяет быстро перезагрузить систему.
Кнопка Clear CMOS Switch позволяет быстро сбросить установки CMOS.
94
ASRock FM2A85X Extreme4 Motherboard
Page 95
2. Информация о BIOS
Утилита настройки BIOS (BIOS Setup) хранится во флэш-памяти на материнской плате. Чтобы войти в программу настройки BIOS Setup, при запуске компьютера нажмите <F2> или <Del> во время самопроверки при включении питания (Power-On-Self-Test – POST). Если этого не сделать, то процедуры тестирования POST будут продолжаться обычным образом. Если вы захотите вызвать BIOS Setup уже после POST, перезапустите систему с помощью клавиш <Ctrl> + <Alt> + <Delete> или нажатия кнопки сброса системы. Подробную информацию о программе BIOS Setup вы найдете в Руководстве пользователя (в формате PDF) на компакт-диске поддержки.
на корпусе
3. Информация о компакт-диске поддержки с программным обеспечением
Данная материнская плата поддерживает различные операционные системы Microsoft® Windows®: 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit. Поставляемый вместе с ней
компакт-диск поддержки содержит необходимые драйверы и полезные утилиты, которые расширяют возможности материнской платы. Чтобы начать работу с компакт-диском поддержки, вставьте его в дисковод CD-ROM. Если в вашем компьютере включена функция автозапуска (AUTORUN), то на экране автоматически появится главное меню компакт-диска (Main Menu). Если этого не произошло, найдите дважды щелкните на нем, чтобы открыть меню.
в папке BIN на компакт-диске поддержки файл ASSETUP.EXE и
ASRock FM2A85X Extreme4 Motherboard
Русский
95
Page 96
1. Introdução
Gratos por comprar nossa placa–mãe FM2A85X Extreme4 um produto confi ável feito com ASRock um estrito controle de qualidade consistente. Com um excelente desempenho, essa placa é dotada de um projeto robusto que atende a ASRock de compromisso com a qualidade e durabilidade. Este Guia de Instalação Rápida apresenta a placa-mãe e o guia de instalação pas­so a passo. Mais informações detalhadas sobre a placa-mãe podem ser encontra­das no manual do usuário do CD de suporte.
Português
ser atualizados, o conteúdo deste manual pode ser cambiado sem aviso. Em caso de qualquer modifi cação deste manual, a versão atualizada estará disponível no website de ASRock sem prévio aviso. Pode também encontrar as listas das mais recentes placas VGA e das CPUs suportadas no site da web da ASRock. Website de ASRock http://www.asrock.com Se precisar de apoio técnico em relação a este placa-mãe, por favor visite o nosso sítio da internet para informação específi ca acerca do modelo que está a utilizar. www.asrock.com/support/index.asp
Porque as especifi cações da placa mãe e o software de BIOS poderiam
1.1 Este pacote contém
Placa-mãe ASRock FM2A85X Extreme4 (Formato ATX) Guia de instalação rápida da ASRock FM2A85X Extreme4 CD de suporte da placa ASRock FM2A85X Extreme4 Quatro cabo de dados ATA Serial (SATA) (Opcional) Uma proteção I/O
A ASRock recorda-lhe...
Para obter melhor desempenho em Windows® 8 / 8 64-bit / 7 / 7 64-bit /
TM
Vista
/ VistaTM 64-bit, recomendamos que defi na a opção Confi guração de Armazenamento na BIOS para o modo AHCI. Para mais detalhes acerca da confi guração da BIOS consulte o “Manual de utilizador” no nosso CD de suporte.
96
ASRock FM2A85X Extreme4 Motherboard
Page 97
1.2 Especifi cações
Plataforma - Formato ATX
- Design de condensadores banhados a ouro de alta qualidade (Condensadores de polímeros condutores de alta qualidade 100% fabricados no Japão) CPU
- Alimentação de 4 + 2 fases
- Suporta a tecnologia Cool ‘n’ Quiet da AMD
- UMI-Link GEN2 Chipsets - AMD A85X (Hudson-D4) Memória
- Suporte à tecnologia de memória de duplo canal
- 4 x slots de DDR3 DIMM
- Suporta memória DDR3 2600+(OC)/2400(OC)/2133(OC)/1866
/1600/1333/1066/800, não ECC, sem tampão
- Capacidade máxima de memória do sistema: 64GB
- Suporta Extreme Memory Profi le (XMP)1.3/1.2 da Intel
- Suporta Perfi l de Memória AMD (AMP)
Slots de - 2 x slots de PCI Express 2.0 x16
Expansão (PCIE2: modo x16; PCIE4: modo x4)
- 2 x slots de PCI Express 2.0 x1
- 3 x slots de PCI
AMD
VGA integrado - Placa gráfi ca AMD Radeon HD Série 7000
- DirectX 11, Pixel Shader 5.0
- Memória partilhada máxima 2GB
- Suporta HDMI 1.4a Tecnologia com resolução máxima até 1920x1200 @ 60Hz
- Suporta Dual-link DVI com resolução máxima até 2560x1600 @ 75Hz
- Suporta D-Sub com resolução máxima até 1920x1600 @ 60Hz
- Suporta as funções Auto Lip Sync (Sincronização automática do som), Deep Color (Profundidade da cor) (12bpc), xvYCC e HBR (áudio de taxa de bits elevada) com HDMI (é necessário um monitor compatível com a norma HDMI)
- Suporta 3D Estereoscópico Blu-ray com HDMI 1.4a
- Suporta AMD Steady Video pós-processamento de vídeo para redução automática de
- Suporte para processadores com Socket FM2 de 100W
®
- Suporta Quad CrossFireXTM, CrossFireXTM e Dual Graphics da
- Três opções de saída VGA: D-Sub, DVI-D e HDMI
TM
2.0: Nova capacidade de
Português
ASRock FM2A85X Extreme4 Motherboard
97
Page 98
Português
98
vibrações em vídeo local/online
- Suporta função HDCP com portas DVI e HDMI
- Suporta a norma Blu-ray de alta defi nição 1080p (BD) / e a
reprodução de DVDs de alta defi nição com portas DVI e
HDMI
Áudio - Áudio HD de 7.1 canais com protecção de conteúdo
(Realtek ALC892 Audio Codec)
- Suporte áudio Blu-ray superior
- Suporta TruStudioTM da THX LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111E
- Suporta Wake-On-LAN
- Suporta Detecção de cabo LAN
- Suporta Ethernet com Efi ciência Energética 802.3az
- Suporta PXE Entrada/Saída I/O Panel pelo painel - 1 x porta para teclado/mouse PS/2
- 1 x porta D-Sub
- 1 x porta DVI-D
- 1 x porta HDMI
- 1 x Porta de saída SPDIF óptica
- 2 x portas USB 2.0 padrão
- 6 x portas USB 3.0 padrão
- 1 x porta LAN RJ-45 com LED (LED ACT/LIG e LED VELOCIDADE)
- Ficha de áudio HD: Altifalante traseiro/Central/Baixos/Entrada
de linha/Altifalante frontal/Microfone
SATA3 - 7 x conectores SATA3 a 6,0 Gb/s, com suporte para RAID (RAID 0, RAID 1, RAID 5 e RAID 10), NCQ, AHCI e funções Hot Plug USB3.0 - 2 x Portas USB 3.0 traseiras através de A85X (Hudson-D4) da AMD, com suporte para USB 1.1/2.0/3.0 até 5Gb/s
- 4 x Portas USB 3.0 traseiras através de EJ188 da Etron, com
suporte para USB 1.1/2.0/3.0 até 5Gb/s
- 1 x Conector USB 3.0 frontal (suporta 2 portas USB 3.0)
através de A85X (Hudson-D4) da AMD, com suporte para USB
1.1/2.0/3.0 até 5Gb/s
Conectores
dados de até 6,0 Gb/s
- 1 x Conector do módulo de infravermelho
- 1 x Conector eSATA3
- 1 x Interruptor para limpar o CMOS com LED
- 7 x conectores SATA3, suporte a taxa de transferência de
ASRock FM2A85X Extreme4 Motherboard
Page 99
- 1 x Conector CIR
- 1 x conector de porta COM
- 1 x Conector HDMI_SPDIF
- 1 x Conector para LED de alimentação
- 2 x Conector do ventilador da CPU (1 x 4 pinos, 1 x 3 pinos)
- 3 x Conector do ventilador da chassis (1 x 4 pinos, 2 x 3 pinos)
- 1 x Conector do ventilador da energia (3 pinos)
- Conector de força do ATX de 24 pinos
- Conector ATX 12 V de 8 pinos
- Conector Áudio do painel frontal
- 3 x cabezal USB 2.0 (suporta 6 portas USB 2.0)
- 1 x cabezal USB 3.0 (suporta 2 portas USB 3.0)
- 1 x Dr. Debug com LED
- 1 x Interruptor de alimentação LED
- 1 x Interruptor de reposição LED
BIOS - 64Mb BIOS UEFI ofi cial da AMI com suporte para GUI
- Suporta dispositivos “Plug and Play”
- ACPI 1.1 atendendo a eventos de “wake up”
- Suporta dispositivos sem jumper
- Suporte para SMBIOS 2.3.1
- DRAM, APU PCIE VDDP, CPU e CPU NB/GFX Voltage Multi-adjustment CD de suporte - Controladores, utilitários, software antivírus (Experimentacao Versao), CyberLink MediaEspresso 6.5 versão de demonstração, Navegador Google Chrome e Barra de Ferramentas Monitor do HW - Sensores de temperature do procesador
- Medição de temperatura da placa-mãe
- Tacômetros de ventilador do Processador/chassis/energia
- Ventoinha silenciosa para a CPU
- CPU/Chassis Fan Controle Multi-Velocidade
- Monitoramento de voltagem : +12 V, +5 V, +3.3 V, Vcore Sistema - Microsoft Operacional
/ Vista
®
Windows® 8 / 8 de 64 bits / 7 / 7 de 64 bits / Vista
TM
de 64 bits
Certi cações - FCC, CE, WHQL
- “ErP/EuP Ready” (é necessária alimentação eléctrica “ErP/ EuP Ready”)
* Para informações mais detalhadas por favor visite o nosso sítio Web: http://www.asrock.com
TM
Português
ASRock FM2A85X Extreme4 Motherboard
99
Page 100
1.3 Confi guração dos Jumpers
A ilustração mostra como os jumpers são confi gurados. Quando há uma capa de jumpers sobre os pinos, diz–se que o jump­er está “curto”. Não havendo capa sobre os pinos, o jumper está “aberto”. A ilustração mostra um jumper de 3 pinos em que os pinos 1 e 2 están “curtos” quando a capa de jumper estiver colocada sobre esses 2 pinos.
Jumper Confi guração
Restaurar CMOS
(CLRCMOS1, jumper de 3 pinos) (veja a folha 2, No. 27)
Nota: CLRCMOS1 permite você limpar os dados em CMOS. Os dados em CMOS
incluem informações da confi guração do sistema como: por exemplo a senha do sistema, data, tempo, e os parámetros da confi guração do sistema. Para limpar e reconfi gurar os parámetros do sistema a confi guração inicial da fá- brica, por favor desligue o cabo de força, ponha em curto–circuito os pin 2 e pin 3 de CLRCMOS1 por mais de 5 segundos para limpar o CMOS usando um jumper. Por favor lembrese de remover o jumper depois de limpar o COMS. Se precisar limpar o CMOS ao concluir a atualização do BIOS, de­verá reiniciar o sistema primeiro e, em seguida, desligá-lo antes de executar a ação de limpeza o CMO
hora, perfil predefinido de utilizador, 1394 GUID e endereço MAC apenas serão limpos se a bateria do CMOS for retirada.
Confi guração-padrão Limpar o CMOS
S. Tenha em atenção que a palavra-passe, data,
Português
100
O Interruptor para limpar o CMOS tem a mesma função do Jumper para limpar o CMOS.
ASRock FM2A85X Extreme4 Motherboard
Loading...