ASRock FM2A85X User Manual [en, ru, de, es, fr, it]

Page 1

No part of this installation guide may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this guide are furnished for informational use

only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this guide. With respect to the contents of this guide, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or condi-

tions of merchantability or tness for a particular purpose. In no event shall ASRock, its directors, ofcers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of

data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/perchlorate”

ASRock Website: http://www.asrock.com

Published July 2013

ASRock FM2A85X Extreme4-M Motherboard

English

Page 2

Motherboard Layout

SO CK ET FM 2

FM2 A85 X Ex tre me4 -M

AMD

A85 X

(Hu dso n-D 4 )

Chi pse t

CMOS

BATTE RY

ATXP W R1

DDR3 _A1 (64 bit, 2 40-pi n modu le)

DDR3 _A2 (64 bit, 2 40-pi n modu le)

DDR3 _B1 (64 bit, 2 40-pi n modu le)

DDR3 _B2 (64 bit, 2 40-pi n modu le)

DDR3 26 00+

64Mb BIOS

Super

I/O

ATX12V1

PWR_FAN1

CPU_FAN1

CPU_FAN2

LAN

AUDIO CODEC

CLRCMOS1

Fron tU SB 3.0

SATA3_2

SATA3_5

SATA3_1

SATA3_4

HDLED RESE T

PLED PWRBTN

PANEL1

CHA_FAN1

SPEAKER1

IR1

PLED1

COM1

CIR1

USB5_6

USB7_8

USB9_10

HD_AUDIO 1

LPT1

PCIE 1

PCIE 3

PCI1

DX11

ErP/ EuP Ready

RoH S

USB3 .0 T:USB1 B:US B2

Ps2

Keyboa rd/

Mouse

HDMI 1

VGA 1

DVI_ CON1

USB 2.0 T:U SB1 B: USB2

eSATA

Top: RJ-45

USB 2.0 T:U SB3 B: USB4

Top:

CTR BASS

Center:

REAR SPK

Bottom:

Optical

SPDIF

Top:

LINE IN

Center:

FRONT

Bottom:

MIC IN

Dual Gr aphic s

Design edin Taip ei

13 14

16 17

1920

2930

Fast USB

USB3_3_4

PCIE 2

Fast RAM

Fast LAN

SATA3_3

CI1

SATA3_7

SATA3_8

English

1 Power Fan Connector (PWR_FAN1) 2

ATX 12V Power Connector (ATX12V1) 3 CPU Heatsink Retention Module 4 CPU Socket 5 CPU Fan Connector (CPU_FAN1) 6 CPU Fan Connector (CPU_FAN2) 7 2 x 240-pin DDR3 DIMM Slots (DDR3_A1, DDR3_B1) 8 2 x 240-pin DDR3 DIMM Slots (DDR3_A2, DDR3_B2) 9 ATX Power Connector (ATXPWR1) 10 USB 3.0 Header (USB3_3_4) 11 Southbridge Controller 12

Chassis Fan Connector (CHA_FAN1) 13 SPI Flash Memory (64Mb) 14 SATA3 Connector (SATA3_8) 15 SATA3 Connector (SATA3_7) 16 SATA3 Connector (SATA3_5) 17 SATA3 Connector (SATA3_4) 18 SATA3 Connector (SATA3_1)

ASRock FM2A85X Extreme4-M Motherboard

19 SATA3 Connector (SATA3_2) 20 SATA3 Connector (SATA3_3) 21

Chassis Speaker Header (SPEAKER1) 22 Power LED Header (PLED1) 23 System Panel Header (PANEL1) 24 USB 2.0 Header (USB5_6) 25 Clear CMOS Jumper (CLRCMOS1) 26 USB 2.0 Header (USB7_8) 27 Consumer Infrared Module Header (CIR1) 28 USB 2.0 Header (USB9_10) 29 Print Port Header (LPT1) 30 COM Port Header (COM1) 31 Infrared Module Header (IR1) 32 33 PCI Slot (PCI1)

Front Panel Audio Header (HD_AUDIO1)

34 PCI Express 2.0 x16 Slot (PCIE3) 35 Chassis Intrusion Header (CI1) 36 PCI Express 2.0 x1 Slot (PCIE2) 37 PCI Express 2.0 x16 Slot (PCIE1)

Page 3

I/O Panel

1 PS/2 Mouse/Keyboard Port (Green/Purple) 2 D-Sub Port (VGA) 3 USB 2.0 Ports (USB_1_2) 4 LAN RJ-45 Port * 5 Central / Bass (Orange) 6 Rear Speaker (Black) 7 Optical SPDIF Out Port

* There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

8 Line In (Light Blue) 9 Front Speaker (Lime) ** 10 Microphone (Pink) 11 USB 2.0 Ports (USB_3_4) 12 eSATA3 Connector *** 13 HDMI Port 14 DVI-D Port 15 USB 3.0 Ports (USB3_1_2)

LAN Port LED Indications

Activity/Link LED SPEED LED

Status Description Status Description Off No Link Off 10Mbps connection Blinking Data Activity Orange 100Mbps connection On 100Mbps connection Green 1Gbps connection

ASRock FM2A85X Extreme4-M Motherboard

ACT/LINK LED

LAN Port

SPEED LED

English

Page 4

** If you use a 2-channel speaker, please connect the speaker’s plug into “Front

Speaker Jack”. See the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output

Channels

2 V -- -- -4 V V -- -6 V V V -8 V V V V

To enable Multi-Streaming function, you need to connect a front panel audio cable

to the front panel audio header. After restarting your computer, you will nd “Mixer”

tool on your system. Please select “Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”.

Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio.

*** eSATA3 connector supports SATA Gen3 in cable 1M.

Front Speaker

(No. 9)

Rear Speaker

(No. 6)

Central / Bass

(No. 5)

Line In

(No. 8)

English

ASRock FM2A85X Extreme4-M Motherboard

Page 5

1. Introduction

Thank you for purchasing ASRock FM2A85X Extreme4-M motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance. In this manual, chapter 1 and 2 contains the introduction of the motherboard and step-by-step hardware installation guide. Chapter 3 and 4 con-

tains the conguration guide of BIOS setup and information of the Support

CD.

Because the motherboard specications and the BIOS software

might be updated, the content of this manual will be subject to

change without notice. In case any modications of this manual

occur, the updated version will be available on ASRock’s web-

site without further notice. You may nd the latest VGA cards

and CPU support list on ASRock’s website as well. ASRock website http://www.asrock.com

If you require technical support related to this motherboard,

please visit our website for specic information about the model

you are using. www.asrock.com/support/index.asp

1.1 Package Contents

ASRock FM2A85X Extreme4-M Motherboard (Micro ATX Form Factor) ASRock FM2A85X Extreme4-M Quick Installation Guide ASRock FM2A85X Extreme4-M Support CD 4 x Serial ATA (SATA) Data Cables (Optional) 1 x I/O Panel Shield

ASRock Reminds You...

To get better performance in Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

the BIOS option in Storage Conguration to AHCI mode.

For the BIOS setup, please refer to the “User Manual” in our support CD for details.

/ VistaTM 64-bit, it is recommended to set

ASRock FM2A85X Extreme4-M Motherboard

English

Page 6

English

1.2 Specications

Platform - Micro ATX Form Factor

- ASRock DuraCap (2.5 x longer life time) (100% Japan-made high-quality Conductive Polymer Capacitors) CPU - Support for Socket FM2 100W processors

- 4 + 2 Power Phase Design

- Supports AMD’s Cool ‘n’ QuietTM Technology

- UMI-Link GEN2

Chipset - AMD A85X (Hudson-D4) Memory - Dual Channel DDR3 Memory Technology

- 4 x DDR3 DIMM slots

- Support DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/ 1600/1333/1066/800 non-ECC, un-buffered memory (see CAUTION 1)

- Max. capacity of system memory: 64GB (see CAUTION 2)

- Supports Intel® Extreme Memory Prole (XMP) 1.3 /

1.2

- Supports AMD Memory Prole (AMP)

Expansion Slot - 2 x PCI Express 2.0 x16 slots (PCIE1 @ x16 mode; PCIE3 @ x4 mode)

- 1 x PCI Express 2.0 x1 slot

- 1 x PCI slot

- Supports AMD Quad CrossFireXTM, CrossFireXTM and Dual Graphics Graphics - AMD Radeon HD 7000 series graphics

- DirectX 11, Pixel Shader 5.0

- Max. shared memory 2GB

- Three VGA Output options: D-Sub, DVI-D and HDMI

- Supports HDMI 1.4a Technology with max. resolution up to 1920x1200 @ 60Hz

- Supports Dual-link DVI with max. resolution up to 2560x1600 @ 75Hz

- Supports D-Sub with max. resolution up to 1920x 1600 @ 60Hz

ASRock FM2A85X Extreme4-M Motherboard

Page 7

- Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate Audio) with HDMI (see CAUTION 3)

- Supports Blu-ray Stereoscopic 3D with HDMI 1.4a

- Supports AMD Steady VideoTM 2.0: New video post processing capability for automatic jutter reduction on home/online video

- Supports HDCP with DVI and HDMI ports

- Supports Full HD 1080p Blu-ray (BD) / HD-DVD playback with DVI and HDMI ports Audio - 7.1 CH HD Audio with Content Protection (Realtek ALC892 Audio Codec)

- Premium Blu-ray audio support LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supports Wake-On-LAN

- Supports LAN Cable Detection

- Supports Energy Efcient Ethernet 802.3az

- Supports PXE Rear Panel I/O I/O Panel

- 1 x PS/2 Mouse/Keyboard Port

- 1 x D-Sub Port

- 1 x DVI-D Port

- 1 x HDMI Port

- 1 x Optical SPDIF Out Port

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x eSATA3 Connector

- 2 x Ready-to-Use USB 3.0 Ports

- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

- HD Audio Jack: Rear Speaker/Central/Bass/Line in/ Front Speaker/Microphone SATA3 - 7 x SATA3 6.0 Gb/s connectors, support RAID (RAID 0, RAID 1, RAID 5 and RAID 10), NCQ, AHCI and Hot Plug

English

ASRock FM2A85X Extreme4-M Motherboard

Page 8

English

USB 3.0

to 5Gb/s

- 1 x Front USB 3.0 header (supports 2 USB 3.0 ports), supports USB 1.1/2.0/3.0 up to 5Gb/s Connector - 7 x SATA3 6.0Gb/s connectors

- 1 x IR header

- 1 x CIR header

- 1 x Print port header

- 1 x COM port header

- 1 x Power LED header

- 1 x Chassis Intrusion header

- 2 x CPU Fan connectors (1 x 4-pin, 1 x 3-pin)

- 1 x Chassis Fan connector (4-pin)

- 1 x Power Fan connector (3-pin)

- 24 pin ATX power connector

- 8 pin 12V power connector

- Front panel audio connector

- 3 x USB 2.0 headers (support 6 USB 2.0 ports)

- 1 x USB 3.0 header (supports 2 USB 3.0 ports) BIOS Feature - 64Mb AMI UEFI Legal BIOS with GUI support

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

- DRAM, APU PCIE VDDP, CPU and CPU NB/GFX Voltage Multi-adjustment Support CD - Drivers, Utilities, AntiVirus Software (Trial Version), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser and Toolbar Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer

- CPU/Chassis Quiet Fan

- CPU/Chassis Fan Multi-Speed Control

- CASE OPEN detection

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

- 2 x Rear USB 3.0 ports, support USB 1.1/2.0/3.0 up

ASRock FM2A85X Extreme4-M Motherboard

Page 9

OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM

/ VistaTM 64-bit compliant Certications - FCC, CE, WHQL

- ErP/EuP Ready (ErP/EuP ready power supply is required) * For detailed product information, please visit our website: http://www.asrock.com

WARNING

Please realize that there is a certain risk involved with

overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using thirdparty overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 10

CAUTION!

1. Whether 2600/2400/2133/1866/1600MHz memory speed is supported depends on the CPU you adopt. If you want to adopt DDR3 2600/2400/2133/1866/1600 memory module on this motherboard, please refer to the memory support list on our website for the compatible memory modules.

ASRock website http://www.asrock.com

2. Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 8 / 7 / VistaTM. For Windows® 64-bit OS with 64-bit CPU, there is no such limitation. You can use ASRock XFast RAM to utilize the memory that Windows® cannot use.

3. xvYCC and Deep Color are only supported under Windows® 8 64-bit / 8 / 7 64-bit / 7. Deep Color mode will be enabled only if the display supports 12bpc in EDID. HBR is supported under Windows® 8 64-bit / 8 / 7 64-bit / 7 / VistaTM 64-bit / VistaTM.

English

ASRock FM2A85X Extreme4-M Motherboard

Page 11

1.3 Unique Features

ASRock Extreme Tuning Utility (AXTU)

ASRock Extreme Tuning Utility (AXTU) is an all-in-

one tool to ne-tune different system functions in a userfriendly interface, which includes Hardware Monitor, Fan Control, Overclocking, OC DNA, IES and XFast RAM. In Hardware Monitor, it shows the major readings of your system. In Fan Control, it shows the fan speed and temperature for you to adjust. In Overclocking, you are allowed to overclock CPU frequency for optimal system performance. In OC DNA, you can save your OC settings as a profile and share it with your friends. Your

friends then can load the OC prole to their own system

to get the same OC settings. In IES (Intelligent Energy Saver), the voltage regulator can reduce the number of

output phases to improve efciency when the CPU cores

are idle without sacrificing computing performance. In XFast RAM, it fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU.

ASRock Instant Boot

ASRock Instant Boot allows you to turn on your PC in

just a few seconds, provides a much more efcient way

to save energy, time, money, and improves system running speed for your system. It leverages the S3 and S4 ACPI features which normally enable the Sleep/Standby and Hibernation modes in Windows® to shorten boot up

time. By calling S3 and S4 at specic timing during the

shutdown and startup process, Instant Boot allows you to enter your Windows® desktop in a few seconds.

ASRock Instant Flash

ASRock Instant Flash is a BIOS ash utility embedded

in Flash ROM. This convenient BIOS update tool allows you to update system BIOS without entering operating

systems rst like MS-DOS or Windows®. With this utility,

ASRock FM2A85X Extreme4-M Motherboard

English

Page 12

you can press the <F6> key during the POST or the

<F2> key to enter into the BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save

the new BIOS le to your USB ash drive, oppy disk or

hard drive, then you can update your BIOS only in a few

clicks without preparing an additional oppy diskette or other complicated ash utility. Please be noted that the USB ash drive or hard drive must use FAT32/16/12 le

system.

ASRock APP Charger

If you desire a faster, less restricted way of charging your

Apple devices, such as iPhone/iPad/iPod Touch, ASRock has prepared a wonderful solution for you - ASRock APP Charger. Simply install the APP Charger driver, it makes your iPhone charge much quickly from your computer and up to 40% faster than before. ASRock APP Charger allows you to quickly charge many Apple devices simultaneously and even supports continuous charging when your PC enters into Standby mode (S1), Suspend to RAM (S3), hibernation mode (S4) or power off (S5). With APP Charger driver installed, you can easily enjoy the marvelous charging experience.

English

ASRock XFast USB

ASRock XFast USB can boost USB storage device per-

formance. The performance may depend on the properties of the device.

ASRock XFast LAN

ASRock XFast LAN provides a faster internet access,

which includes the benets listed below. LAN Application Prioritization: You can congure your application’s prior-

ity ideally and/or add new programs. Lower Latency in Game: After setting online game’s priority higher, it can lower the latency in games. Traffic Shaping: You can watch Youtube HD videos and download simultaneously.

ASRock FM2A85X Extreme4-M Motherboard

Page 13

Real-Time Analysis of Your Data: With the status win-

dow, you can easily recognize which data streams you are transferring currently.

ASRock XFast RAM

ASRock XFast RAM is a new function that is included

into ASRock Extreme Tuning Utility (AXTU). It fully utilizes the memory space that cannot be used under Windows® OS 32-bit CPU. ASRock XFast RAM shortens the loading time of previously visited websites, making web

surng faster than ever. And it also boosts the speed of

Adobe Photoshop 5 times faster. Another advantage of ASRock XFast RAM is that it reduces the frequency of accessing your SSDs or HDDs in order to extend their lifespan.

ASRock Crashless BIOS

ASRock Crashless BIOS allows users to update their

BIOS without fear of failing. If power loss occurs during the BIOS update process, ASRock Crashless BIOS will automatically finish the BIOS update procedure after regaining power. Please note that BIOS files need to be placed in the root directory of your USB disk. Only USB2.0 ports support this feature.

ASRock OMG (Online Management Guard)

Administrators are able to establish an internet curfew or

restrict internet access at specied times via OMG. You

may schedule the starting and ending hours of internet access granted to other users. In order to prevent users from bypassing OMG, guest accounts without permission to modify the system time are required.

ASRock Internet Flash

ASRock Internet Flash searches for available UEFI rm-

ware updates from our servers. In other words, the system can auto-detect the latest UEFI from our servers

ASRock FM2A85X Extreme4-M Motherboard

English

Page 14

and ash them without entering Windows® OS. Please

note that you must be running on a DHCP configured computer in order to enable this function.

ASRock UEFI System Browser

ASRock UEFI system browser is a useful tool included in

graphical UEFI. It can detect the devices and congurations that users are currently using in their PC. With the UEFI system browser, you can easily examine the cur-

rent system conguration in UEFI setup.

ASRock On/Off Play Technology

ASRock On/Off Play Technology allows users to enjoy

the great audio experience from the portable audio devices, such like MP3 player or mobile phone to your PC, even when the PC is turned off (or in ACPI S5 mode)! This motherboard also provides a free 3.5mm audio cable (optional) that ensures users the most convenient computing environment.

ASRock Dehumidier Function

Users may prevent motherboard damages due to damp-

ness by enabling “Dehumidifier Function”. When en-

abling Dehumidier Function, the computer will power on

automatically to dehumidify the system after entering S4/ S5 state.

English

ASRock Easy RAID Installer

ASRock Easy RAID Installer can help you to copy the

RAID driver from a support CD to your USB storage device. After copying the RAID driver to your USB storage device, please change “SATA Mode” to “RAID”, then you can start installing the OS in RAID mode.

ASRock Interactive UEFI

ASRock Interactive UEFI is a blend of system congura-

tion tools, cool sound effects and stunning visuals. The

ASRock FM2A85X Extreme4-M Motherboard

Page 15

unprecedented UEFI provides a more attractive interface

and brings a lot more amusement.

ASRock Fast Boot

With ASRock’s exclusive Fast Boot technology, it takes

less than 1.5 seconds to logon to Windows® 8 from a cold boot. No more waiting! The speedy boot will completely change your user experience and behavior.

ASRock X-Boost

Brilliantly designed for combo overclocking, ASRock X-

Boost Technology is able to unleash the hidden power of your CPUs. Simply press “X” when turning on the PC, X-Boost will automatically overclock the relative components to get up to 15.77% performance boost! With the smart X-Boost, overclocking CPU can become a near one-button process.

ASRock Restart to UEFI

Windows® 8 brings the ultimate boot up experience.

The lightning boot up speed makes it hard to access the UEFI setup. ASRock Restart to UEFI technology is designed for those requiring frequent UEFI access. It allows users to easily enter the UEFI automatically when turning on the PC next time. Just simply enable this function; the PC will be assured to access the UEFI directly in the very beginning.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 16

2. Installation

This is a micro ATX form factor motherboard. Before you install the moth-

erboard, study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

1. Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so may cause physical injuries to you and damages to motherboard components.

2. In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.

5. When placing screws to secure the motherboard to the chassis, please do not over-tighten the screws! Doing so may damage the motherboard.

English

ASRock FM2A85X Extreme4-M Motherboard

Page 17

2.1 CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90 Step 2. Position the CPU directly above the socket so that the CPU corner with the golden triangle matches the small triangle on the socket’s corner.

Step 3. Carefully insert the CPU into the socket until it ts in place.

The CPU ts only in one correct orientation. DO NOT force

the CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it rmly on the socket while you

push down the socket lever to secure the CPU. The lever clicks on the side tab to indicate that it is locked.

Lever 90° Up

CPU Golden Triangle

Socket Corner Small Triangle

angle.

STEP 1: Lift Up The Socket Lever

STEP 2 / STEP 3: Match The CPU’s Golden Triangle To The Small Triangle on the Socket’s Corner

STEP 4: Push Down And Lock The Socket Lever

2.2 Installation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install a compatible heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other. Then connect the CPU fan to the CPU FAN connector (CPU_FAN1, see Page 2, No. 5 or CPU_FAN2, see Page 2, No. 6). For proper installation, please kindly refer to the instruction manual of the CPU fan and the heatsink.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 18

2.3 Installation of Memory Modules (DIMM)

This motherboard provides four 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Dual Channel Memory Technology. For dual channel conguration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM pairs. In other words, you have to install identical DDR3 DIMM pairs in Dual Channel A (DDR3_A1 and DDR3_B1, see p.2 No. 7) or identical DDR3 DIMM pairs in Dual Channel B (DDR3_A2 and DDR3_B2, see p.2 No. 8), so that Dual Channel Memory Technology can be activated. This motherboard also allows you to install four DDR3 DIMMs for dual channel

conguration, please install identical DDR3 DIMMs in all four slots. You may refer to the Dual Channel Memory Conguration Table below.

Dual Channel Memory Congurations

DDR3_A1

(Black Slot) (1) Populated - Populated (2) - Populated - Populated (3) Populated Populated Populated Populated

* For conguration (3), please install identical DDR3 DIMMs in all four slots.

DDR3_A2

(Black Slot)

DDR3_B1

(Black Slot)

DDR3_B2

(Black Slot)

English

1. If you want to install two memory modules, for optimal compatibility and reliability, it is recommended to install them in DDR3_A1 and DDR3_B1 or in DDR3_A2 and DDR3_B2.

2. If only one memory module or three memory modules are installed in the DDR3 DIMM slots on this motherboard, it is unable to activate the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual Channel, for example, installing a pair of memory modules in DDR3_A1 and DDR3_A2, it is unable to activate Dual Channel Memory Technology.

4. It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; otherwise, this motherboard and DIMM

ASRock FM2A85X Extreme4-M Motherboard

Page 19

may be damaged.

5. If you adopt DDR3 2600/2400/2133/1866/1600 memory modules on this motherboard, it is recommended to install them on DDR3_A2 and DDR3_B2 slots.

Installing a DIMM

Please make sure to disconnect the power supply before adding or removing DIMMs or system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward. Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

no t ch break

no t ch

break

The DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 20

English

2.4 Expansion Slots (PCI and PCI Express Slots)

There is 1 PCI slot and 3 PCI Express slots on this motherboard. PCI Slot: The PCI slot is used to install expansion cards that have 32-bit PCI interface.

PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express x16 lane width

graphics cards, or used to install PCI Express graphics cards to support CrossFireXTM function.

PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane

width. Such as Gigabit LAN card or SATA2 cards, etc.

PCIE3 (PCIE x16 slot) is used for PCI Express x4 lane width

cards, or used to install PCI Express graphics cards to support CrossFireXTM function.

1. In single VGA card mode, it is recommended to install a

PCI Express x16 graphics card on PCIE1 slot.

2. In CrossFireXTM mode, please install PCI Express x16

graphics cards on PCIE1 and PCIE3 slots.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the

power supply is switched off and the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already

installed in a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep

the screws for later use.

Step 4. Align the card connector with the slot and press rmly until the

card is completely seated on the slot. Step 5. Fasten the card to the chassis with screws. Step 6. Replace the system cover.

ASRock FM2A85X Extreme4-M Motherboard

Page 21

2.5 CrossFireXTM and Quad CrossFireXTM Operation Guide

This motherboard supports CrossFireXTM and Quad CrossFireXTM. CrossFireXTM technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units (GPU) in a single PC. Combining a range of different operating modes with intelligent software design and an innovative interconnect mechanism, CrossFireXTM enables the highest possible level of performance and image quality in any 3D application. Please check AMD website for AMD CrossFireXTM driver updates.

1. If a customer incorrectly congures their system they will not see

the performance benefits of CrossFireXTM. All three CrossFireXTM components, a CrossFireXTM Ready graphics card, a CrossFireXTM Ready motherboard and a CrossFireXTM Edition co-processor graphics card, must be installed correctly to benefit from the CrossFireXTM multi-GPU platform.

2. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both cards will operate as 12-pipe cards while in CrossFireXTM mode.

2.5.1 Graphics Card Setup

Different CrossFireXTM cards may require different methods to enable

CrossFireXTM feature. For other CrossFireXTM cards that AMD has released or will release in the future, please refer to AMD graphics card manuals for detailed installation guide.

Step 1. Insert one Radeon graphics card into PCIE1 slot and the other

Radeon graphics card to PCIE3 slot. Make sure that the cards are properly seated on the slots.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 22

English

Step 2. Connect two Radeon graphics cards by installing a CrossFire

Bridge on the top of the Radeon graphics cards. (The CrossFire Bridge is provided with the graphics card you purchase, not bundled with this motherboard. Please refer to your graphics card vendor for details.)

CrossFire Bridge

Step 3. Connect the DVI monitor cable to the DVI connector on the Rad-

eon graphics card on PCIE1 slot. (You may use the DVI to D-Sub adapter to convert the DVI connector to D-Sub interface, and then connect the D-Sub monitor cable to the DVI to D-Sub adapter.)

ASRock FM2A85X Extreme4-M Motherboard

Page 23

2.5.2 Driver Installation and Setup

Step 1. Power on your computer and boot into OS. Step 2. Remove the AMD driver if you have any VGA driver installed in

your system.

The Catalyst Uninstaller is an optional download. We recommend using

this utility to uninstall any previously installed Catalyst drivers prior to installation. Please check AMD’s website for AMD driver updates.

Step 3. Install the required drivers to your system.

For Windows® 8 / 7 / VistaTM OS:

Install the CATALYST Control Center. Please check AMD’s web-

site for details.

Step 4. Restart your computer. Step 5. Install the VGA card drivers to your system, and restart your com-

puter. Then you will nd “AMD Catalyst Control Center” on your

Windows® taskbar.

AMD Catalyst Control Center

Step 6. Double-click “AMD Catalyst Control Center”. Click “View”, select

“CrossFireXTM”, and then check the item “Enable CrossFireXTM”. Select “2 GPUs” and click “Apply” (if you install two Radeon graphics cards).

ASRock FM2A85X Extreme4-M Motherboard

English

Page 24

English

Although you have selected the option “Enable CrossFireTM”, the Cross-

FireXTM function may not work actually. Your computer will automatically

reboot. After restarting your computer, please conrm whether the option

“Enable CrossFireTM” in “AMD Catalyst Control Center” is selected or not;

if not, please select it again, and then you are able to enjoy the benet of

CrossFireX

feature.

Step 7. You can freely enjoy the benet of CrossFireXTM or Quad CrossFi-

reXTM feature.

* CrossFireXTM appearing here is a registered trademark of AMD Technologies Inc.,

and is used only for identication or explanation and to the owners’ benet,

without intent to infringe. * For further information of AMD CrossFireXTM technology, please check AMD’s website for updates and details.

ASRock FM2A85X Extreme4-M Motherboard

Page 25

2.6 Jumpers Setup

The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when jumper cap is placed on these 2 pins.

Clear CMOS Jumper

(CLRCMOS1) (see p.2, No. 25)

CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS.

If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the

clear-CMOS action. Please be noted that the password, date, time, user

default prole, 1394 GUID and MAC address will be cleared only if the

CMOS battery is removed.

Clear CMOSDefault

If you clear the CMOS, the case open may be detected. Please

adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 26

2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard!

Serial ATA3 Connectors

(SATA3_1: see p.2, No. 18) (SATA3_2: see p.2, No. 19) (SATA3_3:

SATA3_7 SATA3_5 SATA3_4 see p.2, No. 20) (SATA3_4: see p.2, No. 17) (SATA3_5:

SATA3_3 SATA3_2 SATA3_1 see p.2, No. 16) (SATA3_7: see p.2, No. 15) (SATA3_8: see p.2, No. 14)

Serial ATA (SATA) Data Cable

(Optional)

SATA3_8

These seven Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6.0 Gb/s data transfer rate.

Either end of the SATA data cable can be connected to SATA / SATA2 / SATA3 hard disks or the SATA2 / SATA3 connectors on this motherboard.

English

Print Port Header

(25-pin LPT1) (see p.2, No. 29)

AFD #

STB #

ERR OR#

PIN I T#

SPD 1

SPD 0

SLI N #

SPD 2

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

This is an interface for print port cables that allows convenient connection of printer

devices.

SLC T

ASRock FM2A85X Extreme4-M Motherboard

Page 27

USB 2.0 Headers and Ports

(9-pin USB5_6) (see p.2 No. 24)

(9-pin USB7_8) (see p.2 No. 26)

(9-pin USB9_10) (see p.2 No. 28)

USB _PWR

P-6

P-5

P-8

P-7

P-1 0

P-9

P+6

P+5

P+8

P+7

P+1 0

P+9

GND

DUM MY

Besides four default USB 2.0 ports on the I/O panel, there are three USB 2.0 headers on this motherboard. Each USB 2.0 header can support two USB 2.0 ports.

USB 3.0 Header

(19-pin USB3_3_4) (see p.2, No. 10)

Int A_P3 _SSR X-

Int A_P3 _SSR X+

Int A_P3 _SST X-

Int A_P3 _SST X+

Infrared Module Header

(5-pin IR1) (see p.2, No. 31)

Consumer Infrared Module Header

(4-pin CIR1) (see p.2, No. 27)

ASRock FM2A85X Extreme4-M Motherboard

Vbu s

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

Besides two default USB 3.0 ports on the I/O panel, there is one USB 3.0 header on this motherboard. Each USB

3.0 header can support two USB 3.0 ports.

This hea der supp orts an optional wireless transmitting and receiving infrared module.

Th is hea der can be us ed t o con n e c t t h e r e m o t e controller receiver.

English

Page 28

Front Panel Audio Header

(9-pin HD_AUDIO1) (see p.2, No. 32)

1. High Denition Audio supports Jack Sensing, but the panel

wire on the chassis must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel. E. To activate the front mic. For Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM

64-bit OS:

Go to the "FrontMic" Tab in the Realtek Control panel. Adjust “Recording Volume”.

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

This is an interface for the front panel audio cable that allows convenient connection and control of audio devices.

English

System Panel Header

(9-pin PANEL1) (see p.2, No. 23)

Connect the power switch, reset switch and system status indica-

tor on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

ASRock FM2A85X Extreme4-M Motherboard

This header accommodates several system front panel functions.

Page 29

PWRBTN (Power Switch): Connect to the power switch on the chassis front panel. You may

congure the way to turn off your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the

reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED): Connect to the power status indicator on the chassis front panel.

The LED is on when the system is operating. The LED keeps blinking when the sys-tem is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5).

HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel.

The LED is on when the hard drive is reading or writing data.

The front panel design may differ by chassis. A front panel mod-

ule mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

Chassis Speaker Header

(4-pin SPEAKER1) (see p.2, No. 21)

Power LED Header

(3-pin PLED1) (see p.2, No. 22)

ASRock FM2A85X Extreme4-M Motherboard

Please connect the chassis speaker to this header.

Please connect the chassis power LED to this header to indicate syste m power status. The LED is on when the system is operating. The LED keeps blinking in S1 state. The LED is off in S3/ S4 state or S5 state (power off).

English

Page 30

Chassis and Power Fan Connectors

(4-pin CHA_FAN1) (see p.2, No. 12)

(4-pin PWR_FAN1) (see p.2, No. 1)

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

Please connect the fan cables to the fan connectors and match the black wire to the ground pin.

CPU Fan Connectors

(4-pin CPU_FAN1) (see p.2, No. 5)

Though this motherboard provides a 4-Pin CPU fan (Quiet Fan)

connector, 3-Pin CPU fans can still work successfully even without the fan speed control function. If you plan to connect a 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

(3-pin CPU_FAN2) (see p.2, No. 6)

ATX Power Connector

(24-pin ATXPWR1) (see p.2, No. 9)

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

GND

+12 V

CPU _FAN_ SPEE D

12 124

Please connect the CPU fan cable to the connector and match the black wire to the ground pin.

Pin 1-3 Connected

3-Pin Fan Installation

Please connect an ATX power supply to this connector.

English

Though this motherboard provides a 24-pin ATX

power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use a 20pin ATX power supply, please plug your power supply along Pin 1 and Pin 13.

20-Pin ATX Power Supply Installation

ASRock FM2A85X Extreme4-M Motherboard

Page 31

ATX 12V Power Connector

(8-pin ATX12V1) (see p.2, No. 2)

Though this motherboard provides an 8-pin ATX 12V power con-

nector, it can still work if you adopt a traditional 4-pin ATX 12V power supply. To use a 4-pin ATX power supply, please plug your power supply along Pin 1 and Pin 5.

4 8

1 5

Please connect an ATX 12V power supply to this connector.

4 8

Serial port Header

(9-pin COM1) (see p.2, No. 30)

Chassis Intrusion Header

(2-pin CI1) (see p.2, No. 35)

4-Pin ATX 12V Power Supply Installation

This COM1 header supports a serial port module.

Sig n al

GND

This motherboard supports CA S E OP E N dete c t i o n which detects whether the chassis cover has been removed. This feature requires a chassis with chassis intrusion detection design.

1 5

ASRock FM2A85X Extreme4-M Motherboard

English

Page 32

2.8 Driver Installation Guide

To install the drivers to your system, please insert the support CD to your

optical drive rst. Then, the drivers compatible to your system can be auto-

detected and listed on the support CD driver page. Please follow the order from top to bottom to install those required drivers. Therefore, the drivers you install can work properly.

2.9 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / Vista

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA3 HDDs with RAID, please refer to the document at the following path in the Support CD for detailed procedures:

..\ RAID Installation Guide

64-bit With RAID

2.10 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / Vista

If you want to install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your SATA3 HDDs without RAID, please follow the steps below.

64-bit Without RAID

English

Using SATA3 HDDs without NCQ

STEP 1: Set Up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage

Conguration.

B. Set the option “SATA Mode” to [IDE].

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

ASRock FM2A85X Extreme4-M Motherboard

Page 33

Using SATA3 HDDs with NCQ

STEP 1: Set Up UEFI.

A. Enter UEFI SETUP UTILITY Advanced screen Storage

Conguration.

B. Set the option “SATA Mode” to [AHCI].

STEP 2: Install Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your system.

ASRock FM2A85X Extreme4-M Motherboard

English

Page 34

3. BIOS Information

The Flash Memory on the motherboard stores the BIOS Setup Utility. When you start up the computer, please press <F2> or <Del> during the Power-On-Self-Test (POST) to enter the BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> + <Delete>, or pressing the reset button on the system chassis. The BIOS Setup program is designed to be user-friendly. It is a menu-driven program, which allows you to scroll through its various sub-menus and to select among the predetermined choices. For detailed information about BIOS Setup, please refer

to the User Manual (PDF le) contained in the Support CD.

4. Software Support CD information

English

This motherboard supports various Microsoft® Windows® operating systems: 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / Vista that came with the motherboard contains necessary drivers and useful utilities that will enhance motherboard features. To begin using the Support CD, insert the CD into your CD-ROM drive. It will display the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main Menu

does not appear automatically, locate and double-click the le “ASRSETUP.

EXE” in the Support CD to display the menu.

64-bit. The Support CD

ASRock FM2A85X Extreme4-M Motherboard

Page 35

1. Einführung

Wir danken Ihnen für den Kauf des ASRock FM2A85X Extreme4-M Motherboard, ein zuverlässiges Produkt, welches unter den ständigen, strengen Qualitätskontrollen von ASRock gefertigt wurde. Es bietet Ihnen exzellente Leistung und robustes Design, gemäß der Verpflichtung von ASRock zu Qualität und Halbarkeit. Diese Schnellinstallationsanleitung führt in das Motherboard und die schrittweise Instal-

lation ein. Details über das Motherboard nden Sie in der Bedienungsanleitung auf

der Support-CD.

Da sich Motherboard-Spezikationen und BIOS-Software verändern können,

kann der Inhalt dieses Handbuches ebenfalls jederzeit geändert werden. Für den Fall, dass sich Änderungen an diesem Handbuch ergeben, wird eine neue Version auf der ASRock-Website, ohne weitere Ankündigung, verfügbar sein.

Die neuesten Grakkarten und unterstützten CPUs sind auch auf der ASRock-

Website aufgelistet. ASRock-Website: http://www.asrock.com Wenn Sie technische Unterstützung zu Ihrem Motherboard oder spezische

Informationen zu Ihrem Modell benötigen, besuchen Sie bitte unsere Webseite:

www.asrock.com/support/index.asp

1.1 Kartoninhalt

ASRock FM2A85X Extreme4-M Motherboard (Micro ATX-Formfaktor) ASRock FM2A85X Extreme4-M Schnellinstallationsanleitung ASRock FM2A85X Extreme4-M Support-CD Vier Serial ATA (SATA) -Datenkabel (optional) Ein I/O Shield

ASRock erinnert...

Zur besseren Leistung unter Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / Vista / VistaTM 64 Bit empfehlen wir, die Speicherkonguration im BIOS auf den

AHCI-Modus einzustellen. Hinweise zu den BIOS-Einstellungen nden

Sie in der Bedienungsanleitung auf der mitgelieferten CD.

ASRock FM2A85X Extreme4-M Motherboard

Deutsch

Page 36

Deutsch

1.2 Spezikationen

Plattform - Micro ATX-Formfaktor

- Alle Feste Kondensatordesign (100% in Japan gefertigte, erstklassige leitfähige Polymer-Kondensatoren) CPU - Unterstützt Sockel-FM2-100-W-Prozessoren

- 4 + 2-Stromphasendesign

- Unterstützt Cool ‘n’ QuietTM-Technologie von AMD

- UMI-Link-GEN2

Chipsatz - AMD A85X (Hudson-D4) Speicher - Unterstützung von Dual-Kanal-Speichertechnologie

- 4 x Steckplätze für DDR3

- Unterstützt DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/ 1600/1333/1066/800 non-ECC, ungepufferter Speicher

- Max. Kapazität des Systemspeichers: 64GB

- Unterstützt Intel® Extreme Memory Prole (XMP)1.3/1.2

- Unterstützt AMD Memory Prole (AMP)

Erweiterungs- - 2 x PCI-Express-2.0-x16-Steckplätze (PCIE1: x16-Modus; steckplätze PCIE3: x4-Modus)

- 1 x PCI-Express-2.0-x1-Steckplätze

- 1 x PCI -Steckplätze

- Unterstützt AMD Quad CrossFireXTM, CrossFireXTM und

duale Grakkarten Onboard-VGA - AMD Radeon HD 7000-Grak

- DirectX 11, Pixel Shader 5.0

- Maximal gemeinsam genutzter Speicher 2GB

- Drei VGA-Ausgangsoptionen: D-Sub, DVI-D sowie HDMI

- Unterstützt HDMI 1.4a mit einer maximalen Auösung von

1920 x 1200 bei 60 Hz

- Unterstützt Dual-link DVI mit einer maximalen Auösung von

2560 x 1600 bei 75 Hz

- Unterstützt D-Sub mit einer maximalen Auösung von 1920

x 1600 bei 60 Hz

- Unterstützt Auto Lip Sync, Deep Color (12bpc), xvYCC und HBR (High Bit Rate-Audio) mit HDMI

- Unterstützt stereoskopisches 3D per Blu-ray mit HDMI 1.4a

- Unterstützt AMD Steady VideoTM 2.0: Neuartige Funktion der Videonachbearbeitung für automatische Reduzierung von Bildschwankungen bei Heim-/Online-Videos

- Unterstützt HDCP mit DVI- und HDMI-Ports

- Unterstutzt 1080p Blu-ray (BD) / HD-DVD-Wiedergabe mit

ASRock FM2A85X Extreme4-M Motherboard

Page 37

DVI- und HDMI-Ports Audio - 7.1 CH HD Audio mit dem Inhalt Schutz (Realtek ALC892 Audio Codec)

- Premium Blu-ray-Audio-Unterstützung LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Unterstützt Wake-On-LAN

- Unterstützt LAN-Kabelerkennung

- Unterstützt energieefzientes Ethernet 802.3az

- Unterstützt PXE E/A-Anschlüsse I/O Panel an der - 1 x PS/2-Maus/Tastaturanschluss Rückseite - 1 x D-Sub port

- 1 x DVI-D port

- 1 x HDMI port

- 1 x Optischer SPDIF-Ausgang

- 4 x Standard-USB 2.0-Anschlüsse

- 1 x eSATA3-Anschluss

- 2 x Standard-USB 3.0-Anschlüsse

- 1 x RJ-45 LAN Port mit LED (ACT/LINK LED und SPEED LED)

- HD Audiobuchse: Lautsprecher hinten / Mitte/Bass / Audioeingang / Lautsprecher vorne / Mikrofon SATA3 - 7 x SATA 3-Anschluss mit 6,0 Gb/s, unterstützt RAID- (RAID 0, RAID 1, RAID 5 und RAID 10), NCQ-, AHCI- und Hot Plug USB3.0 - 2 x USB 3.0-Ports an der Rückseite, unterstützt USB

1.1/2.0/3.0 mit bis zu 5 Gb/s

- 1 x USB 3.0-Header (unterstützt zwei USB 3.0-Ports) an der Vorderseite, unterstützt USB 1.1/2.0/3.0 mit bis zu 5 Gb/s Anschlüsse - 7 x SATA3 6,0 GB/s-Anschlüsse

- 1 x Infrarot-Modul-Header

- 1 x Consumer Infrarot-Modul-Header

- 1 x Druckerport-Anschlussleiste

- 1 x COM-Anschluss-Header

- 1 x Betriebs-LED-Header

- 1 x Verteiler für Gehäuse Eindringversuche

- 2 x CPUlüfter-Anschluss (1 x 4-pin, 1 x 3-pin)

- 1 x Gehäuselüfter-Anschluss (4-pin)

- 1 x Stromlüfter-Anschluss (3-pin)

Deutsch

ASRock FM2A85X Extreme4-M Motherboard

Page 38

- 24-pin ATX-Netz-Header

- 8-pin anschluss für 12V-ATX-Netzteil

- Anschluss für Audio auf der Gehäusevorderseite

- 3 x USB 2.0-Anschlüsse (Unterstützung 6 zusätzlicher USB 2.0-Anschlüsse)

- 1 x USB 3.0-Anschlüsse (Unterstützung 2 zusätzlicher USB 3.0-Anschlüsse) BIOS - 64Mb AMIs Legal BIOS UEFI mit GUI-Unterstützung

- Unterstützung für “Plug and Play”

- ACPI 1.1-Weckfunktionen

- JumperFree-Modus

- SMBIOS 2.3.1

- DRAM, APU PCIE VDDP, CPU und CPU NB/GFX Stromspannung Multianpassung Support-CD - Treiber, Dienstprogramme, Antivirussoftware (Probeversion), Cyber Link MediaEspresso 6.5-Testversion, Google Chrome Browser und Toolbar Hardware Monitor - CPU-Temperatursensor

- Motherboardtemperaturerkennung

- Drehzahlmessung für CPU/Gehäuse/Stromlüfter

- Geräuscharmer CPU-/Gehäuselüfter

- Mehrstuge Geschwindigkeitsteuerung für CPU-/

Gehäuselüfter

- GEHÄUSE OFFEN-Erkennung

- Spannungsüberwachung: +12V, +5V, +3.3V, Vcore

Betriebssysteme - Unterstützt Microsoft VistaTM / Vista

64-Bit

Windows® 8 / 8 64-Bit / 7 / 7 64-Bit /

Zertizierungen - FCC, CE, WHQL

- Gemäß Ökodesign-Richtlinie (ErP/EuP) (Stromversorgung gemäß Ökodesign-Richtlinie (ErP/EuP) erforderlich)

* Für die ausführliche Produktinformation, besuchen Sie bitte unsere Website: http://www.asrock.com

Deutsch

ASRock FM2A85X Extreme4-M Motherboard

Page 39

1.3 Einstellung der Jumper

Die Abbildung verdeutlicht, wie Jumper gesetzt werden. Werden Pins durch Jumperkappen verdeckt, ist der Jumper “Gebrückt”. Werden keine Pins durch Jumperkappen verdeckt, ist der Jumper “Offen”. Die Abbildung zeigt einen 3-Pin Jumper dessen Pin1 und Pin2 “Ge-

brückt” sind, bzw. es bendet sich eine

Jumper-Kappe auf diesen beiden Pins.

Jumper Einstellun Beschreibung

CMOS löschen

(CLRCMOS1, 3-Pin jumper) (siehe S.2, No. 25)

Hinweis:

CLRCMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Zurücksetzen der Systemparameter auf die Standardeinrichtung

schalten Sie den Computer bitte aus und trennen das Netzkabel von der Stromversorgung. Warten Sie 15 Sekunden, schließen Sie dann Pin2 und Pin3 am CLRCMOS1 über einen Jumper fünf Sekunden lang kurz. Sie sollten das CMOS allerdings nicht direkt nach der BIOS-Aktualisierung

löschen. Wenn Sie das CMOS nach Abschluss der BIOS-Aktualisierung löschen müssen, fahren Sie zuerst das System hoch. Fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Uhrzeit, benutzerdeniertes Prol, 1394 GUID und MAC-Adresse nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.

DefaultEinstellung

CMOS

löschen

Durch Löschen des CMOS kann erkannt werden, wenn das Gehäuseoffen

ist. Bitte stellen Sie zum Löschen der Aufzeichnung des vorherigenGehäu-

seindringungsstatus die BIOS-Option “Status leeren” ein.

ASRock FM2A85X Extreme4-M Motherboard

Deutsch

Page 40

1.4 Anschlüsse

Integrierte Header und Anschlüsse sind KEINE Jumper. Setzen Sie KEINE Jumperkappen auf diese Header und Anschlüsse. Wenn Sie Jumperkappen auf Header und Anschlüsse setzen, wird das Motherboard unreparierbar beschädigt!

Seriell-ATA3-Anschlüsse Diese sieben Serial ATA3-

(SATA3_1: siehe S.2 - No. 18)

(SATA3_2: siehe S.2 - No. 19)

(SATA3_3: siehe S.2 - No. 20)

(SATA3_4: siehe S.2 - No. 17)

(SATA3_5: siehe S.2 - No. 16)

(SATA3_7: siehe S.2 - No. 15)

(SATA3_8: siehe S.2 - No. 14)

(SATA3-)Verbínder unterstützten SATA-Datenkabel für interne

SATA3_7 SATA3_5 SATA3_4

Massenspeichergeräte. Die aktuelle SATA3- Schnittstelle

ermöglicht eine

Datenübertragungsrate bis 6,0

SATA3_3 SATA3_2 SATA3_1

Gb/s.

Serial ATA- (SATA-) SJedes Ende des SATA Datenkabel Datenkabels kann an die

(Option)

SATA3 Festplatte oder das SATA3 Verbindungsstück auf dieser Hauptplatine angeschlossen werden.

SATA3_8

Deutsch

Druckerport-Anschlussleiste Dies ist eine Schnittstelle zum

AFD #

STB #

ERR OR#

PIN I T#

SPD 1

SPD 0

SLI N #

SPD 2

SPD 3

SPD 4

SPD 5

GND

SPD 6

SPD 7

ACK #

BUS Y

SLC T

(25-pol. LPT1)

(siehe S.2 - No. 29)

Anschluss eines Druckerport-

Kabels, mit dem Sie passende

Drucker auf einfache Weise

anschließen können.

ASRock FM2A85X Extreme4-M Motherboard

Page 41

USB 2.0-Header Zusätzlich zu den vier üblichen

(9-pol. USB5_6)

(siehe S.2 - No. 24)

USB 2.0-Ports an den I/O-

Anschlüssen benden sich drei

USB 2.0-Anschlussleisten am Motherboard. Pro USB 2.0 Anschlussleiste werden zwei

(9-pol. USB7_8)

(siehe S.2 - No. 26)

(9-pol. USB9_10)

(siehe S.2 - No. 28)

USB 2.0-Ports unterstützt.

USB _PWR

P-6

P+6

GND

DUM MY

GND

P+5

P-5

P-8

P+8

GND

DUM MY

GND

P+7

P-7

P-1 0

P+1 0

GND

DUM MY

GND

P+9

P-9

USB 3.0-Header Neben zwei Standard-USB

(19-pol. USB3_3_4)

(siehe S.2 - No. 10)

3.0-Ports am E/A-Panel

bendet sich ein USB 3.0-

Header an diesem Motherboard. Dieser USB 3.0 Header kann zwei USB 3.0 Ports unterstützen.

Vbu s

Int A_P3 _SSR X-

Int A_P3 _SSR X+

GND

Int A_P3 _SST X-

Int A_P3 _SST X+

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

Infrarot-Modul-Header Dieser Header unterstützt ein

(5-pin IR1)

optionales, drahtloses Sende-

(siehe S.2 - No. 31)

und Empfangs-Infrarotmodul.

Consumer Infrared-Modul-Header Dieser Header kann zum

(4-pin CIR1)

(siehe S.2 - No. 27)

Anschließen Remote-

Empfänger.

ASRock FM2A85X Extreme4-M Motherboard

Deutsch

Page 42

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

Anschluss für Audio auf Dieses Interface zu einem der Gehäusevorderseite Audio-Panel auf der Vorder

(9-Pin HD_AUDIO1)

(siehe S.2 - No. 32)

seite Ihres Gehäuses,

ermöglicht Ihnen eine bequeme

Anschlussmöglichkeit und

Kontrolle über Audio-Geräte.

1. High Denition Audio unterstützt Jack Sensing (automatische Erkennung falsch

angeschlossener Geräte), wobei jedoch die Bildschirmverdrahtung am Gehäuse HDA unterstützen muss, um richtig zu funktionieren. Beachten Sie bei der Installation im System die Anweisungen in unserem Handbuch und im Gehäusehandbuch.

2. Wenn Sie die AC’97-Audioleiste verwenden, installieren Sie diese wie nachstehend beschrieben an der Front-Audioanschlussleiste: A. Schließen Sie Mic_IN (MIC) an MIC2_L an. B. Schließen Sie Audio_R (RIN) an OUT2_R und Audio_L (LIN) an OUT2_L an. C. Schließen Sie Ground (GND) an Ground (GND) an. D. MIC_RET und OUT_RET sind nur für den HD-Audioanschluss gedacht. Diese Anschlüsse müssen nicht an die AC’97-Audioleiste angeschlossen werden.

E. So aktivieren Sie das Mikrofon an der Vorderseite.

Bei den Betriebssystemen Windows® 8 / 8 64 Bit / 7 / 7 64 Bit / VistaTM / VistaTM 64 Bit:

Wählen Sie im Realtek-Bedienfeld die „FrontMic“ (Vorderes Mikrofon)- Registerkarte. Passen Sie die „Recording Volume“ (Aufnahmelautstärke) an.

Deutsch

System Panel-Header Dieser Header unterstützt

(9-pin PANEL1)

(siehe S.2 - No. 23)

Schließen Sie die Ein-/Austaste, die Reset-Taste und die Systemstatusanzeige am Gehäuse an diesen Header an; befolgen Sie dabei die nachstehenden Hinweise zur Pinbelegung. Beachten Sie die positiven und negativen Pins, bevor Sie die Kabel anschließen.

PWRBTN (Ein-/Ausschalter):

mehrere Funktion der

Systemvorderseite.

Zum Anschließen des Ein-/Ausschalters an der Frontblende des Gehäu

ses. Sie können kongurieren, wie das System mit Hilfe des Ein-/Ausschalters ausgeschaltet werden können soll.

ASRock FM2A85X Extreme4-M Motherboard

Page 43

RESET (Reset-Taste):

Zum Anschließen der Reset-Taste an der Frontblende des Gehäuses.

Mit der Reset-Taste können Sie den Computer im Falle eines Absturzes

neu starten.

PLED (Systembetriebs-LED):

Zum Anschließen der Betriebsstatusanzeige an der Frontblende des Gehäuses. Die LED leuchtet, wenn das System in Betrieb ist. Die LED

blinkt, wenn sich das System im Ruhezustand S1 bendet. Die LED schaltet sich aus, wenn sich das System in den Modi S3/S4 bendet

oder ausgeschaltet ist (S5).

HDLED (Festplattenaktivitäts-LED):

Zum Anschließen der Festplattenaktivitäts-LED an der Frontblende des Gehäuses. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt.

Das Design der Frontblende kann je nach Gehäuse variiere. Ein Frontblendenmodul besteht hauptsächlich aus einer Ein-/Austaste, einer Reset-Taste, einer Betriebs-LED, einer Festplattenaktivitäts-LED, Lautsprechern, etc. Stellen Sie beim Anschließen des Frontblendenmoduls Ihres Gehäuses an diesem Header sicher, dass die Kabel- und Pinbelegung korrekt übereinstimmen.

Gehäuselautsprecher-Header Schließen Sie den

(4-pin SPEAKER1)

(siehe S.2 - No. 21)

Gehäuselautsprecher an

diesen Header an.

Betriebs-LED-Header Bitte schließen Sie die Betriebs-

(3-pin PLED1)

(siehe S.2 - No. 22)

LED des Gehäuses zur Anzeige

des Systembetriebsstatus an diesem Header an. Die LED leuchtet, wenn das System in Betrieb ist. Die LED blinkt im S1-Zustand. Im S3/S4- oder S5-Zustand (ausgeschaltet) leuchtet die LED nicht.

ASRock FM2A85X Extreme4-M Motherboard

Deutsch

Page 44

Gehäuse- und Stromlüfteranschlüsse Verbinden Sie die Lüfterkabel

(4-pin CHA_FAN1)

(siehe S.2, No. 12)

mit den Lüfteranschlüssen,

wobei der schwarze Draht an

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

den Schutzleiterstift

(3-pin PWR_FAN1)

(siehe S.2 - No. 1)

angeschlossenwird.

Deutsch

CPU-Lüfteranschluss Verbinden Sie das CPU -

(4-pin CPU_FAN1)

(siehe S.2 - No. 5)

Lüfterkabel mit diesem

Anschluss und passen Sie den

schwarzen Draht dem

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Erdungsstift an.

Obwohl dieses Motherboard einen vierpoligen CPU-Lüfteranschluss

(Quiet Fan) bietet, können auch CPU-Lüfter mit dreipoligem Anschluss

angeschlossen werden; auch ohne Geschwindigkeitsregulierung. Wenn Sie einen dreipoligen CPU-Lüfter an den CPU-Lüferanschluss dieses

Motherboards anschließen möchten, verbinden Sie ihn bitte mit den

Pins 1 – 3.

Lüfter mit dreipoligem Anschluss installieren

(3-pin CPU_FAN2) (sieche S.2 - No. 6)

ATX-Netz-Header Verbinden Sie die ATX-

(24-pin ATXPWR1)

(siehe S.2 - No. 9)

Stromversorgung mit diesem

Header.

GND

+12 V

12 124

CPU _FAN_ SPEE D

Pins 1–3 anschließen

ASRock FM2A85X Extreme4-M Motherboard

Page 45

Obwohl dieses Motherboard einen 24-pol. ATX Stromanschluss bietet, kann es auch mit einem

modizierten traditionellen 20-pol. ATX-Netzteil

verwendet werden. Um ein 20-pol. ATX-Netzteil zu verwenden, stecken Sie den Stecker mit Pin 1 und Pin 13 ein.

Installation eines 20-pol. ATX-Netzteils

ATX 12V Anschluss Bitte schließen Sie an diesen

(8-pin ATX12V1)

(siehe S.2 - No. 2)

Anschluss die ATX 12V

Stromversorgung an.

4 8

1 5

Obwohl diese Hauptplatine 8-Pin ATX 12V Stromanschluss zur Verfügung

stellt, kann sie noch arbeiten, wenn Sie einen traditionellen 4-Pin ATX 12V Energieversorgung adoptieren. Um die 4-Pin ATX Energieversorgung zu verwenden, stecken Sie bitte Ihre Energieversorgung zusammen mit dem Pin 1 und Pin 5 ein.

Installation der 4-Pin ATX 12V Energieversorgung

4 8

1 5

COM-Anschluss-Header Dieser COM-Anschluss- Header

(9-pin COM1)

(siehe S.2 - No. 30)

wird verwendet, um ein

COM-Anschlussmodul zu

unterstützen.

Verteiler für Gehäuseeindringversuche Dieses Motherboard unterstützt

(2-pin CI1)

eine Gehäuse-Offen-

(siehe S.2 - No. 35)

Erkennnungsfunktion, die feststellt, ob die

Sig n al

GND

Gehäuseabdeckung entfernt wurde. Diese Funktion erfordert ein Gehäuse, das mit einem Design zur Erkennung von Gehäuseeindringversuchen ausgestattet ist.

Deutsch

ASRock FM2A85X Extreme4-M Motherboard

Page 46

2. BIOS-Information

Das Flash Memory dieses Motherboards speichert das Setup-Utility. Drücken Sie <F2> oder <Del> während des POST (Power-On-Self-Test) um ins Setup zu gelangen, ansonsten werden die Testroutinen weiter abgearbeitet. Wenn Sie ins Setup gelangen wollen, nachdem der POST durchgeführt wurde, müssen Sie das System über die Tastenkombination <Ctrl> + <Alt> + <Delete> oder den Reset-Knopf auf

der Gehäusevorderseite, neu starten. Natürlich können Sie einen Neustart auch

durchführen, indem Sie das System kurz ab- und danach wieder anschalten. Das Setup-Programm ist für eine bequeme Bedienung entwickelt worden. Es ist ein menügesteuertes Programm, in dem Sie durch unterschiedliche Untermenüs scrollen und die vorab festgelegten Optionen auswählen können. Für detaillierte Informationen zum BIOS-Setup, siehe bitte das Benutzerhandbuch (PDF Datei) auf der Support CD.

3. Software Support CD information

Dieses Motherboard unterstützt eine Reiche von Microsoft® Windows® Betriebssystemen: 8 / 8 64-Bit / 7 / 7 64-Bit / VistaTM / VistaTM 64-Bit. Die Ihrem Motherboard beigefügte Support-CD enthält hilfreiche Software, Treiber und Hilfsprogramme, mit

denen Sie die Funktionen Ihres Motherboards verbessern können Legen Sie die

Support-CD zunächst in Ihr CD-ROM-Laufwerk ein. Der Willkommensbildschirm mit den Installationsmenüs der CD wird automatisch aufgerufen, wenn Sie die “Autorun”-Funktion Ihres Systems aktiviert haben. Erscheint der Wilkommensbildschirm nicht, so “doppelklicken” Sie bitte auf das File ASSETUP.EXE im BIN-Verzeichnis der Support-CD, um die Menüs aufzurufen.

Das Setup-Programm soll es Ihnen so leicht wie möglich machen. Es ist menügesteuert, d.h. Sie können in den verschiedenen Untermenüs Ihre Auswahl treffen und

die Programme werden dann automatisch installiert.

Deutsch

ASRock FM2A85X Extreme4-M Motherboard

Page 47

1. Introduction

Merci pour votre achat d’une carte mère ASRock FM2A85X Extreme4-M, une

carte mère très able produite selon les critères de qualité rigoureux de ASRock. Elle offre des performances excellentes et une conception robuste conformément à l’engagement d’ASRock sur la qualité et la abilité au long terme. Ce Guide d’installation rapide présente la carte mère et constitue un guide d’installation pas à pas. Des informations plus détaillées concernant la carte mère pourront être trouvées dans le manuel l’utilisateur qui se trouve sur le CD

d’assistance.

Les spécications de la carte mère et le BIOS ayant pu être mis à jour, le contenu de ce manuel est sujet à des changements sans notication. Au cas où n’importe qu’elle modication intervenait sur ce manuel, la version mise à jour serait disponible sur le site web ASRock sans nouvel avis.

Vous trouverez les listes de prise en charge des cartes VGA et CPU

également sur le site Web ASRock.

Site web ASRock, http://www.asrock.com Si vous avez besoin de support technique en relation avec cette carte mère, veuillez consulter notre site Web pour de plus amples informations particulières au modèle que vous utilisez. www.asrock.com/support/index.asp

1.1 Contenu du paquet

Carte mère ASRock FM2A85X Extreme4-M (Facteur de forme Micro ATX) Guide d’installation rapide ASRock FM2A85X Extreme4-M CD de soutien ASRock FM2A85X Extreme4-M

Quatre câbles de données de série ATA (SATA) (en option)

Un I/O Panel Shield

ASRock vous rappelle...

Pour bénécier des meilleures performances sous Windows® 8 / 8 64 bits

/ 7 / 7 64 bits / Vista

l'option BIOS dans Conguration de stockage en mode AHCI. Pour plus de détails sur l'installation BIOS, référez-vous au "Mode d'emploi" sur

votre CD de support.

/ VistaTM 64 bits, il est recommandé de paramétrer

ASRock FM2A85X Extreme4-M Motherboard

Français

Page 48

Français

1.2 Spécications

Format - Facteur de forme Micro ATX

- Accessoires de Carte mère (condensateurs 100% polymère

conducteur de haute qualité fabriqué au Japon) CPU - Support des unités centrales Socket FM2 100W

- Conception 4 + 2 Power Phase

- Supporte la technologie Cool ‘n’ QuietTM d’AMD

- UMI-Link GEN2

Chipsets - AMD A85X (Hudson-D4) Mémoire - Compatible avec la Technologie de Mémoire à Canal

Double

- 4 x slots DIMM DDR3

- Supporter DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/ 1600/1333/1066/800 non-ECC, sans amortissement

mémoire

- Capacité maxi de mémoire système: 64GB

- Prend en charge le prol de mémoire extrême Intel® (XMP)

1.3/1.2

- Prend en charge le prol de mémoire AMD (AMP) Slot d’extension - 2 x slots PCI Express 2.0 x16 (PCIE1 à mode x16; PCIE3 à mode x4)

- 1 x slot PCI Express 2.0 x1

- 1 x slot PCI

- Support de AMD Quad CrossFireXTM, CrossFireXTM et Dual Graphics

VGA sur carte - Graphiques à l’AMD Radeon HD 7000

- DirectX 11, nuanceur de pixels 5.0

- mémoire partagée max 2GB

- Trois options de sortie VGA: D-Sub, DVI-D et HDMI

- Prend en charge le HDMI 1.4a avec une résolution maximale jusqu’à 1920x1200 @ 60Hz

- Prend en charge le Dual-link DVI avec une résolution maximale jusqu’à 2560x1600 @ 75Hz

- Prend en charge le D-Sub avec une résolution maximale jusqu’à 1920x1600 @ 60Hz

- Prend en charge Lip Sync, Deep Color (12bpc), xvYCC et

HBR (High Bit Rate Audio: Audio à haut débit binaire) avec

HDMI

- Prend en charge la 3D stéréoscopique Blu-ray avec HDMI

1.4a

ASRock FM2A85X Extreme4-M Motherboard

Page 49

- Supporte AMD Steady VideoTM 2.0: Nouvelle fonctionnalité

de traitement post-vidéo pour réduction automatique des tremblements dans les clips vidéo en ligne/maison

- Prise en charge de la HDCP avec ports DVI et HDMI

- Supporter 1080p Blu-ray(BD)/ lecteur de HD-DVD avec ports DVI et HDMI Audio - 7,1 CH HD Audio avec protection de contenu (Realtek ALC892 Audio Codec)

- Prise en charge de l’audio Premium Blu-ray LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supporte du Wake-On-LAN

- Prise en charge de la détection de câble LAN

- Prend en charge la norme Energy Efcient Ethernet 802.3az

- Supporte PXE

Panneau arrière I/O Panel

- 1 x port souris/clavier PS/2

- 1 x port D-Sub

- 1 x port DVI-D

- 1 x port HDMI

- 1 x Port de sortie optique SPDIF

- 4 x ports USB 2.0 par défaut

- 1 x Connecteur eSATA3

- 2 x ports USB 3.0 par défaut

- 1 x port LAN RJ-45 avec LED (ACT/LED CLIGNOTANTE et LED VITESSE)

- Prise HD Audio: Haut-parleur arrière / Central /Basses /

Entrée Ligne / Haut-parleur frontal / Microphone

SATA3 - 7 x connecteurs 6,0 Gb/s SATA3, prise en charge des RAID (RAID 0, RAID 1, RAID 5 et RAID 10), NCQ, AHCI et Hot Plug

USB 3.0 - 2 x ports USB3.0 à l’arrière, prennent en charge USB

1.1/2.0/3.0 jusqu’à 5 Gb/s

- 1 x barrette USB3.0 en façade (prend en charge 2 ports

USB 3.0), prend en charge USB 1.1/2.0/3.0 jusqu’à 5 Gb/s

Connecteurs - 7 x connecteurs SATA3, prennent en charge un taux de

transfert de données pouvant aller jusqu’à 6.0Go/s

- 1 x En-tête du module infrarouge

- 1 x Barrette pour module à infrarouges grand public

- 1 x embase de port d’impression

Français

ASRock FM2A85X Extreme4-M Motherboard

Page 50

Français

- 1 x En-tête de port COM

- 1 x LED di accensione

- 1 x Embase d’intrusion châssis

- 2 x Connecteurs pour ventilateur de CPU (1 x br. 4, 1 x br. 3)

- 1 x Connecteur pour ventilateur de Châssis (br. 4)

- 1 x Connecteur pour ventilateur de pouvoir (br. 3)

- br. 24 connecteur d’alimentation ATX

- br. 8 connecteur d’alimentation 12V ATX

- Connecteur audio panneau avant

- 3 x En-tête USB 2.0 (prendre en charge 6 ports USB 2.0

supplémentaires)

- 1 x En-tête USB 3.0 (prendre en charge 2 ports USB 3.0

supplémentaires)

BIOS - 64Mb AMI UEFI Legal BIOS avec support GUI

- Support du “Plug and Play”

- Compatible pour événements de réveil ACPI 1.1

- Gestion jumperless

- Support SMBIOS 2.3.1

- DRAM, APU PCIE VDDP, CPU et CPU NB/GFX Tension Multi-ajustement CD d’assistance - Pilotes, utilitaires, logiciel anti-virus (Version d’essai), CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser et Toolbar

Surveillance - Détection de la température de l’UC

système - Mesure de température de la carte mère

- Tachéomètre ventilateur CPU/Châssis/Ventilateur

- Ventilateur silencieux pour unité centrale/châssis

- Commande de ventilateur CPU/boîtier à plusieurs vitesses

- Détection d’OUVERTURE DE BOÎTIER

- Monitoring de la tension: +12V, +5V, +3.3V, Vcore OS - Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista

/ VistaTM 64-bit Certications - FCC, CE, WHQL

- Prêt pour ErP/EuP (alimentation Prêt pour ErP/EuP requise)

* Pour de plus amples informations sur les produits, s’il vous plaît visitez notre site web: http://www.asrock.com

ASRock FM2A85X Extreme4-M Motherboard

Page 51

1.3 Réglage des cavaliers

L’illustration explique le réglage des cavaliers. Quand un capuchon est placé sur les

broches, le cavalier est « FERME ». Si aucun capuchon ne relie les broches,le cavalier est « OUVERT ». L’illustration montre un

cavalier à 3 broches dont les broches 1 et 2

sont « FERMEES » quand le capuchon est

placé sur ces 2 broches.

Le cavalier Description

Effacer la CMOS

(CLRCMOS1)

(voir p.2 g. 25)

Remarque :

CLRCMOS1 vous permet d’effacer les données du CMOS. Pour effacer

Paramètres

par défaut

et réinitialiser les paramètres du système à la conguration originale, veuillez éteindre l’ordinateur et débrancher le cordon d’alimentation de

la prise de courant. Après 15 secondes, utilisez un couvercle de jumper pour court-circuiter les broches pin2 et pin3 de CLRCMOS1 pendant

secondes. Veuillez cependant ne pas effacer le CMOS immédiatement

près avoir mis à jour le BIOS. Si vous avez besoin d’effacer le CMOS

après avoir mis à jour le BIOS, vous devez allumer en premier le

système, puis l’éteindre avant de continuer avec l’opération d’effacement du CMOS. Veuillez noter que le mot de passe, la date, l’heure, le prol par défaut de l’utilisateur, 1394 GUID et l’adresse MAC seront effacés seulement si la batterie du CMOS est enlevée.

Effacer la CMOS

Si vous effacez la CMOS, il se peut qu’une ouverture du boîtier soitdé-

tectée. Veuillez ajuster l’option du BIOS “Clear Status” (Effacerl’état) pour effacer la mention d’état d’intrusion dans le châssis.

ASRock FM2A85X Extreme4-M Motherboard

Français

Page 52

1.4 En-têtes et Connecteurs sur Carte

Les en-têtes et connecteurs sur carte NE SONT PAS des cavaliers. NE PAS placer les capuchons de cavalier sur ces en-têtes et connecteurs. Le fait de placer les capuchons de cavalier sur les en-têtes

et connecteurs causera à la carte mère des dommages irréversibles!

Connecteurs Série ATA3 Ces sept connecteurs Série

(SATA3_1: voir p.2 No. 18)

(SATA3_2: voir p.2 No. 19)

(SATA3_3: voir p.2 No. 20)

(SATA3_4: voir p.2 No. 17)

(SATA3_5: voir p.2 No. 16)

(SATA3_7: voir p.2 No. 15)

(SATA3_8: voir p.2 No. 14)

ATA3 (SATA3) prennent en charge les câbles SATA pour

les périphériques de stockage

SATA3_7 SATA3_5 SATA3_4

internes. L’interface SATA3 actuelle permet des taux

transferts de données pouvant

aller jusqu’à 6,0 Gb/s.

SATA3_3 SATA3_2 SATA3_1

Câble de données Toute cote du cable de data Série ATA (SATA) SATA peut etre connecte au

(en option)

disque dur SATA3 ou au connecteur SATA3 sur la carte mere.

SATA3_8

Français

Embase de port d’impression AIl s’agit d’une interface pour le

(LPT1 25 broches)

(voir p.2 No. 29)

pratique de périphériques

d’impression.

En-tête USB 2.0 A côté des quatre ports USB 2.0

(USB5_6 br. 9)

(voir p.2 No. 24)

par défaut sur le panneau E/S,

sur cette carte mère. Chaque embase USB 2.0 peut prendre

AFD #

câble du port d’impression, qui

permet le raccordement

il y a trois embases USB 2.0

STB #

ERR OR#

PIN I T#

SPD 1

SPD 0

SLI N #

SPD 3

SPD 2

USB _PWR

SPD 4

P-6

P-5

SPD 5

P+6

P+5

SPD 6

GND

SPD 7

DUM MY

ACK #

BUS Y

SLC T

en charge 2 ports USB 2.0.

ASRock FM2A85X Extreme4-M Motherboard

Page 53

(USB7_8 br. 9) (voir p.2 No. 26)

(USB9_10 br. 9) (voir p.2 No. 28)

USB _PWR

P-8

P-7

P-1 0

P-9

P+8

P+7

P+1 0

P+9

GND

DUM MY

En-tête USB 3.0 En plus des deux ports USB

(USB3_3_4 br. 19)

(voir p.2 No. 10)

3.0 par défaut sur le panneau

E/S, il y a une barrette USB 3.0 sur la carte mère. Cette barrette USB 3.0 peut prendre en charge deux ports USB 3.0.

Vbu s

Int A_P3 _SSR X-

Int A_P3 _SSR X+

GND

Int A_P3 _SST X-

Int A_P3 _SST X+

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

En-tête du module infrarouge Cet en-tête supporte un module

(IR1 br. 5)

infrarouge optionnel de transfert

(voir p.2 No. 31)

et de réception sans l.

Barrette pour module à infrarouges grand public Cette barrette peut être utilisée

(CIR1 br.4)

(voir p.2 No. 27)

Connecteur audio panneau C’est une interface pour un

(HD_AUDIO1 br. 9)

(voir p.2 No. 32)

contrôle commodes de

périphériques audio.

pour connecter des récepteur.

GND

PRE SENC E#

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

câble avant audio en façade qui

permet le branchement et le

Français

ASRock FM2A85X Extreme4-M Motherboard

Page 54

1. L’audio à haute dénition (HDA) prend en charge la détection de che, mais le l

de panneau sur le châssis doit prendre en charge le HDA pour fonctionner correctement. Veuillez suivre les instructions dans notre manuel et le manuel de

châssis an installer votre système.

2. Si vous utilisez le panneau audio AC’97, installez-le sur l’adaptateur audio

du panneau avant conformément à la procédure ci-dessous: A. Connectez Mic_IN (MIC) à MIC2_L. B. Connectez Audio_R (RIN) à OUT2_R et Audio_L (LIN) à OUT2_L. C. Connectez Ground (GND) à Ground (GND). D. MIC_RET et OUT_RET sont réservés au panneau audio HD. Vous

n’avez pas besoin de les connecter pour le panneau audio AC’97. E. Pour activer le micro avant.

Pour les systèmes d’exploitation Windows® 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / VistaTM 64 bits :

Allez sur l’onglet “FrontMic” (Micro avant) sur le Panneau de contrôle Realtek. Ajustez “Recording Volume” (Volume d’enregistrement).

En-tête du panneau système Cet en-tête permet d’utiliser

(PANEL1 br. 9)

(voir p.2 No. 23)

plusieurs fonctions du panneau

système frontal.

Français

Connectez l’interrupteur d’alimentation, l’interrupteur de réinitialisation et l’indicateur d’état du système du châssis sur cette barrette en respectant l’affectation des broches décrite ci-dessous. Faites attention aux broches positives et négatives avant de connecter les câbles.

PWRBTN (Interrupteur d’alimentation):

Connectez ici le connecteur d’alimentation sur le panneau avant du

châssis. Vous pouvez congurer la façon de mettre votre système hors

tension avec l’interrupteur d’alimentation.

RESET (Interrupteur de réinitialisation):

Connectez ici le connecteur de réinitialisation sur le panneau avant du châssis. Appuyez sur l’interrupteur de réinitialisation pour redémarrer l’ordinateur s’il se bloque ou s’il n’arrive pas à redémarrer normalement.

ASRock FM2A85X Extreme4-M Motherboard

Page 55

PLED (DEL alimentation système):

Connectez ici l’indicateur d’état de l’alimentation sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le système est en marche.

Le voyant DEL clignote lorsque le système est en mode veille S1. Le

voyant DEL est éteint lorsque le système est en mode veille S3/S4 ou lorsqu’il est éteint (S5).

HDLED (DEL activité du disque dur):

Connectez ici le voyant DEL d’activité du disque dur sur le panneau avant du châssis. Ce voyant DEL est allumé lorsque le disque dur est en train de lire ou d’écrire des données.

Le design du panneau avant peut varier en fonction du châssis. Un module de panneau avant consiste principalement en : interrupteur

d’alimentation, interrupteur de réinitialisation, voyant DEL d’alimentation, voyant DEL d’activité du disque dur, haut-parleur, etc. Lorsque vous connectez le panneau avant de votre châssis sur cette barrette, vériez bien à faire correspondre les ls et les broches.

En-tête du haut-parleur Veuillez connecter le de châssis haut-parleur de châssis sur cet

(SPEAKER1 br. 4)

(voir p.2 No. 21)

en-tête.

LED di accensione Collegare il LED di accensione

(PLED1 br. 3)

(voir p.2 Nr. 22)

chassi per indicare lo stato di

alimentazione del sistema. Il LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).

Connecteur pour châssis et ventilateur Branchez les câbles du

(CHA_FAN1 br. 4)

(voir p.2 No. 12)

ventilateur aux connecteurs

pour ventilateur et faites

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

correspondre le l noir à la

(PWR_FAN1 br. 3)

(voir p.2 No. 1)

broche de terre.

ASRock FM2A85X Extreme4-M Motherboard

Français

Page 56

Connecteur du ventilateur Veuillez connecter le câble de de l’UC ventilateur d’UC sur ce

(CPU_FAN1 br. 4)

(voir p.2 No. 5)

connecteur et brancher le l

noir sur la broche de terre.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Bien que cette carte mère offre un support de (Ventilateur silencieux

ventilateur de CPU à 4 broches , le ventilateur de CPU à 3 broches peut

bien fonctionner même sans la fonction de commande de vitesse du

ventilateur. Si vous prévoyez de connecter le ventilateur de CPU à 3

broches au connecteur du ventilateur de CPU sur cette carte mère, veuillez le connecter aux broches 1-3.

Installation de ventilateur à 3 broches

Broches 1-3 connectées

Français

(CPU_FAN2 br. 3) (voir p.2 No. 6)

En-tête d’alimentation ATX Veuillez connecter l’unité

(ATXPWR1 br. 24)

(voir p.2 No. 9)

Bien que cette carte mère fournisse un connecteur de

d’alimentation ATX sur cet

entête.

GND

+12 V

12 124

CPU _FAN_ SPEE D

courant ATX 24 broches, elle peut encore fonctionner si vous adopter une alimentation traditionnelle ATX 20 broches. Pour utiliser une alimentation ATX 20 broches,

branchez à l’alimentation électrique ainsi qu’aux

broches 1 et 13.

20-Installation de l’alimentation électrique ATX

Connecteur ATX 12V Veuillez connecter une unité

(ATX12V1 br.8)

(voir p.2 No. 2)

d’alimentation électrique ATX

12V sur ce connecteur.

4 8

1 5

ASRock FM2A85X Extreme4-M Motherboard

Page 57

Bien que cette carte mère possède 8 broches connecteur d’alimentation ATX 12V, il peut toujours travailler si vous adoptez une approche

traditionnelle à 4 broches ATX 12V alimentation.

Pour utiliser l’alimentation des 4 broches ATX, branchez votre alimentation avec la broche 1 et la broche 5.

4-Installation d’alimentation à 4 broches ATX 12V

4 8

1 5

En-tête de port COM Cette en-tête de port COM est

(COM1 br.9)

(voir p.2 No. 30)

utilisée pour prendre en charge

un module de port COM.

Embase d’intrusion châssis Cette carte-mère prend

(CI1 br.2)

en charge la détection

(voir p.2 No. 35)

d’OUVERTURE DE BOÎTIER,

Sig n al

GND

quidétecte tout retrait du

capot duchâssis. Cette fonction-

nécessite un châssis qui a été-

conçu pour la

détectiond’intrusion dans le

châssis.

Français

ASRock FM2A85X Extreme4-M Motherboard

Page 58

2. Informations sur le BIOS

La puce Flash Memory sur la carte mère stocke le Setup du BIOS. Lorsque vous démarrez l’ordinateur, veuillez presser <F2> ou <Del> pendant le POST (Power-OnSelf-Test) pour entrer dans le BIOS; sinon, le POST continue ses tests de routine. Si

vous désirez entrer dans le BIOS après le POST, veuillez redémarrer le système en

pressant <Ctl> + <Alt> + <Suppr>, ou en pressant le bouton de reset sur le boîtier

du système. Vous pouvez également redémarrer en éteignant le système et en le

rallumant. L’utilitaire d’installation du BIOS est conçu pour être convivial. C’est un

programme piloté par menu, qui vous permet de faire déler par ses divers sousmenus et de choisir parmi les choix prédéterminés. Pour des informations détaillées sur le BIOS, veuillez consulter le Guide de l’utilisateur (chier PDF) dans le CD

technique.

3. Informations sur le CD de support

Cette carte mère supporte divers systèmes d’exploitation Microsoft® Windows®: 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / Vista

carte mère contient les pilotes et les utilitaires nécessaires pour améliorer les fonctions de la carte mère. Pour utiliser le CD technique, insérez-le dans le lecteur de CD-ROM. Le Menu principal s’afche automatiquement si “AUTORUN” est activé

dans votre ordinateur. Si le Menu principal n’apparaît pas automatiquement, locali-

sez dans le CD technique le chier “ASSETUP.EXE” dans le dossier BIN et doublecliquez dessus pour afcher les menus.

64 bits. Le CD technique livré avec cette

Français

ASRock FM2A85X Extreme4-M Motherboard

Page 59

1. Introduzione

Grazie per aver scelto una scheda madre ASRock FM2A85X Extreme4-M, una

scheda madre affidabile prodotta secondo i severi criteri di qualità ASRock. Le

prestazioni eccellenti e il design robusto si conformano all’impegno di ASRock nella

ricerca della qualità e della resistenza.

Questa Guida Rapida all’Installazione contiene l’introduzione alla motherboard e la guida passo-passo all’installazione. Informazioni più dettagliate sulla motherboard si possono trovare nel manuale per l’utente presente nel CD di supporto.

Le speciche della scheda madre e il software del BIOS possono essere

aggiornati, pertanto il contenuto di questo manuale può subire variazioni senza preavviso. Nel caso in cui questo manuale sia

modicato, la versione aggiornata sarà disponibile sul sito di ASRock

senza altro avviso. Sul sito ASRock si possono anche trovare le più recenti schede VGA e gli elenchi di CPU supportate. ASRock website http://www.asrock.com Se si necessita dell’assistenza tecnica per questa scheda madre, visitare

il nostro sito per informazioni speciche sul modello che si sta usando.

www.asrock.com/support/index.asp

1.1 Contenuto della confezione

Scheda madre ASRock FM2A85X Extreme4-M (Micro ATX Form Factor) Guida di installazione rapida ASRock FM2A85X Extreme4-M CD di supporto ASRock FM2A85X Extreme4-M Quattro cavi dati Serial ATA (SATA) (opzionali) Un I/O Shield

ASRock vi ricorda...

Per ottenere migliori prestazioni in Windows® 8 / 8 64-bit / 7 / 7 64-bit /

Vista

/ VistaTM 64-bit, si consiglia di impostare l'opzione BIOS in Storage

Conguration (Congurazione di archiviazione) sulla modalità AHCI. Per

l'impostazione BIOS, fare riferimento a “User Manual” (Manuale dell'utente) nel CD di supporto per dettagli.

ASRock FM2A85X Extreme4-M Motherboard

Italiano

Page 60

Italiano

1.2 Speciche

Piattaforma - Micro ATX Form Factor

- Design condensatore compatto (condensatori a conduttore in

polimero di alta qualità realizzati al 100% in Giappone)

Processore - Supporto per processori socket FM2 100W

- Struttura di fase con alimentazione 4 + 2

- Supporto tecnologia AMD Cool ‘n’ Quiet

- UMI-Link GEN2 Chipset - AMD A85X (Hudson-D4) Memoria - Supporto tecnologia Dual Channel Memory

- 4 x slot DDR3 DIMM

- Supporto DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/ 1333/1066/800 non-ECC, momoria senza buffer

- Capacità massima della memoria di sistema: 64GB

- Supporto di Intel® XMP (Extreme Memory Prole)1.3/1.2

- Supporto di AMD AMP (AMD Memory Prole)

Slot di - 2 x Alloggio PCI Express 2.0 x16 (PCIE1: modalità x16; espansione PCIE3: modalità x4)

- 1 x Alloggio PCI Express 2.0 x1

- 1 x Alloggio PCI

- Supporta AMD Quad CrossFireXTM, CrossFireXTM e Dual Graphics VGA su scheda - Graca AMD Radeon HD 7000

- DirectX 11, Pixel Shader 5.0

- Memoria massima condivisa 2GB

- Tre opzioni d’output VGA: D-Sub, DVI-D e HDMI

- Supporta HDMI 1.4a con risoluzione massima no a

1920x1200 @ 60Hz

- Supporta Dual-link DVI con risoluzione massima no a

2560x1600 @ 75Hz

- Supporta D-Sub con risoluzione massima no a 1920x1600 @

60Hz

- Supporto delle Auto Lip Sync, Deep Color (12bpc), xvYCC e HBR (High Bit Rate Audio) con HDMI

- Supporta Blu-ray Stereoscopico in 3D con HDMI 1.4a

- Supporta AMD Steady VideoTM 2.0: Nuova capacità di post-elab orazione video per la riduzione automatica delle vibrazioni nei video a casa/on-line

- Supporto della HDCP con le porte DVI e HDMI

- Supporto 1080p Blu-ray (BD) / HD-DVD riproduzione con le

ASRock FM2A85X Extreme4-M Motherboard

Page 61

porte DVI e HDMI Audio - 7.1 CH HD Audio con protezioni contenuti (Realtek ALC892 Audio Codec)

- Supporto audio Blu-ray Premium LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Supporta Wake-On-LAN

- Supporta il rilevamento cavo LAN

- Supporto di Energy Efcient Ethernet 802.3az

- Supporta PXE Pannello I/O Panel posteriore I/O - 1 x porta PS/2 per mouse/tastiera

- 1 x Porta D-Sub

- 1 x Porta DVI-D

- 1 x Porta HDMI

- 1 x Porta ottica SPDIF Out

- 4 x porte USB 2.0 già integrate

- 1 x Connettore eSATA3

- 2 x porte USB 3.0 già integrate

- 1 x porte LAN RJ-45 con LED (LED azione/collegamento e

LED velocità)

- Connettore HD Audio: cassa posteriore / cassa centrale / bassi / ingresso linea / cassa frontale / microfono SATA3 - 7 x connettori SATA3 6,0 Gb/s, supporto di RAID (RAID 0, RAID 1, RAID 5 e RAID 10) e delle NCQ, AHCI e Hot Plug USB 3.0 - 2 x porte USB 3.0 posteriori amministrate dal controller,

supporta di USB 1.1/2.0/3.0 no a 5Gb/s

- 1 x header USB 3.0 frontale (supporta 2 porte USB 3.0)

amministrato dal controller, supporto di USB 1.1/2.0/3.0 no a

5Gb/s Connettori - 7 x connettori SATA3 6.0Go/s

- 1 x Collettore modulo infrarossi

- 1 x Connettore modulo infrarosso consumer

- 1 x Collettore porta stampante

- 1 x collettore porta COM

- 1 x LED di accensione

- 1 x header di intrusione dello chassis

- 2 x connettore CPU ventola (1 x 4-pin, 1 x 3-pin)

- 1 x connettore Chassis ventola (4-pin)

- 1 x connettore Alimentazione ventola (3-pin)

Italiano

ASRock FM2A85X Extreme4-M Motherboard

Page 62

- 24-pin collettore alimentazione ATX

- 8-pin connettore ATX 12V

- Connettore audio sul pannello frontale

- 3 x Collettore USB 2.0 (supporta 6 porte USB 2.0)

- 1 x Collettore USB 3.0 (supporta 2 porte USB 3.0) BIOS - 64Mb AMI UEFI Legal BIOS con interfaccia di supporto

- Supporta “Plug and Play”

- Compatibile con ACPI 1.1 wake up events

- Supporta jumperfree

- Supporta SMBIOS 2.3.1

- Regolazione multi-voltaggio DRAM, APU PCIE VDDP, CPU e CPU NB/GFX CD di - Driver, utilità, software antivirus (Versione dimostrativa), supporto CyberLink MediaEspresso 6.5 Trial, Google Chrome Browser e Toolbar Monitoraggio - Sensore per la temperatura del processore Hardware - Sensore temperatura scheda madre

- Indicatore di velocita per la ventola del CPU/Chassis/ Alimentazione

- Ventola CPU/Chassis silenziosa

- Ventola CPU/chassis con controllo di varie velocità

- Rilevamento CASE APERTO

- Voltaggio: +12V, +5V, +3.3V, Vcore Compatibilità - Microsoft® Windows® 8 / 8 64 bit / 7 / 7 64 bit / VistaTM / Vista

64 bit

Certicazioni - FCC, CE, WHQL

- Predisposto ErP/EuP (è necessaria l’alimentazione predis posta per il sistema ErP/EuP)

* Per ulteriori informazioni, prego visitare il nostro sito internet: http://www.asrock.com

Italiano

ASRock FM2A85X Extreme4-M Motherboard

Page 63

1.3 Setup dei Jumpers

L’illustrazione mostra come sono settati i jumper. Quando il ponticello è posizionato sui pin, il jumper è “CORTOCIRCUITATO”. Se sui pin non ci sono ponticelli, il jumper è “APERTO”. L’illustrazione mostra un jumper a 3 pin in cui il pin1 e il pin2 sono “CORTOCIRCUITATI” quando il ponticello è posizionato su questi pin.

Jumper Settaggio del Jumper

Resettare la CMOS

(CLRCMOS1) (vedi p.2 item 25)

Nota:

CLRCMOS1 permette si azzerare i dati nella CMOS. Per cancellare e ripristinare i

parametri del sistema sulla congurazione iniziale, spegnere il computer e

Impostazione

predenita

scollegare il cavo d’alimentazione dalla presa di corrente. Attendere 15 secondi, poi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su CLRCMOS1 per 5 secondi. Tuttavia, si consiglia di non cancellare la CMOS subito dopo avere aggiornato il BIOS. Se si deve azzerare la CMOS quando si è completato l’aggiornamento del BIOS, è necessario per prima cosa avviare il sistema e poi spegnerlo prima di eseguire l’azzeramento della CMOS. Notare

che password, data, ore, prolo utente predenito, 1394 GUID e indirizzo MAC

saranno cancellati solo se è rimossa la batteria della CMOS.

Azzeramen-

to CMOS

Se si cancella la CMOS, potrebbe essere rilevata l’apertura del case.Rego-

lare l’opzione del BIOS “Clear Status” (Cancella stato) per cancellarela registrazione del precedente stato d’intrusione chassis.

ASRock FM2A85X Extreme4-M Motherboard

Italiano

Page 64

1.4 Collettori e Connettori su Scheda

I collettori ed i connettori su scheda NON sono dei jumper. NON installare cappucci per jumper su questi collettori e connettori. L’installazione

di cappucci per jumper su questi collettori e connettori provocherà

danni permanenti alla scheda madre!

Connettori Serial ATA3 Questi sette connettori Serial

(SATA3_1: vedi p.2 Nr. 18)

(SATA3_2: vedi p.2 Nr. 19)

(SATA3_3: vedi p.2 Nr. 20)

(SATA3_4: vedi p.2 Nr. 17)

(SATA3_5: vedi p.2 Nr. 16)

(SATA3_7: vedi p.2 Nr. 15)

(SATA3_8: vedi p.2 Nr. 14)

ATA3 (SATA3) supportano cavi dati SATA per dispositivi di immagazzinamento interni.

SATA3_7 SATA3_5 SATA3_4

L’interfaccia SATA3 attuale

permette velocità di trasferimento dati no a 6.0

SATA3_3 SATA3_2 SATA3_1

Gb/s.

SATA3_8

Cavi dati Serial ATA (SATA) Una o altra estremità del cavo

(Opzionale)

di dati SATA può essere collegata al disco rigido SATA3 o al connettore di SATA3 su questa cartolina base.

Collettore porta stampante Questa è un’interfaccia per il

(LPT1 25 pin)

(vedi p.2 No. 29)

cavo porta stampante che

consente di collegare, con

comodità, dispositivi di stampa.

AFD #

STB #

ERR OR#

PIN I T#

SPD 1

SPD 0

SLI N #

SPD 2

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

SLC T

Italiano

Collettore USB 2.0 Oltre alle quattro porte USB 2.0

(9-pin USB5_6)

(vedi p.2 Nr. 24)

predenite nel pannello I/O, la

scheda madre dispone di tre intestazioni USB 2.0. Ciascuna intestazione USB 2.0 supporta

USB _PWR

P-6

P+6

GND

DUM MY

GND

P+5

P-5

due porte USB 2.0.

ASRock FM2A85X Extreme4-M Motherboard

Page 65

(9-pin USB7_8) (vedi p.2 Nr. 26)

(9-pin USB9_10) (vedi p.2 Nr. 28)

USB _PWR

P-8

P-7

P-1 0

P-9

P+8

P+7

P+1 0

P+9

GND

DUM MY

Collettore USB 3.0 Oltre alle due porte USB 3.0

(19-pin USB3_3_4)

(vedi p.2 Nr. 10)

standard del pannello I/O,

questa scheda madre è dotata di un header USB 3.0 che supporta due porte USB 3.0.

Vbu s

Int A_P3 _SSR X-

Int A_P3 _SSR X+

GND

Int A_P3 _SST X-

Int A_P3 _SST X+

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

Collettore modulo infrarossi Questo collettore supporta

(5-pin IR1)

moduli ad infrarossi optional per

(vedi p.2 Nr. 31)

la trasmissione e la ricezione

senza li.

Connettore modulo infrarosso consumer Questo connettore può essere

(4-pin CIR1)

(vedi p.2 Nr. 27)

Connettore audio sul È un’interfaccia per il cavo del pannello frontale pannello audio. Che consente

(9-pin HD_AUDIO1)

(vedi p.2 Nr. 32)

utilizzato per collegare

ricevitore remoto.

GND

PRE SENC E#

MIC _RET

OUT _RET

connessione facile e controllo

dei dispositivi audio.

MIC 2_R

MIC 2_L

J_S ENSE

OUT 2_R

OUT 2_L

Italiano

ASRock FM2A85X Extreme4-M Motherboard

Page 66

1. La caratteristica HDA (High Denition Audio) supporta il rilevamento dei

connettori, però il pannello dei cavi sul telaio deve supportare la funzione HDA

(High Denition Audio) per far sì che questa operi in modo corretto. Attenersi alle

istruzioni del nostro manuale e del manuale del telaio per installare il sistema.

2. Se si utilizza un pannello audio AC’97, installarlo nell’intestazione audio del pannello anteriore, come indicato di seguito:

A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) ad OUT2_L. C. Collegare Ground (GND) a Ground (GND).

D. MIC_RET e OUT_RET sono solo per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97.

E. Per attivare il microfono frontale.

Sistema operativo Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit:

Andare alla scheda “FrontMic” (Microfono frontale) del pannello di controllo Realtek. Regolare la voce “Recording Volume” (Volume registrazione).

Collettore pannello di sistema Questo collettore accomoda

(9-pin PANEL1)

(vedi p.2 Nr. 23)

diverse funzioni di sistema

pannello frontale.

Italiano

Collegare l’interruttore d’alimentazione, l’interruttore di ripristino, l’indicatore di stato del sistema del pannello frontale del telaio a questo

header in base all’assegnazione dei pin denita di seguito. Determinare i

pin positivi e negativi prima di collegare i cavi.

PWRBTN (interruttore d’alimentazione):

Va collegato all’interruttore d’alimentazione del pannello frontale del

telaio. Usando l’interruttore d’alimentazione si può congurare il modo in

cui si spegne il sistema.

RESET (interruttore di ripristino):

Va collegato all’interruttore di ripristino del pannello frontale del telaio. Premere l’interruttore di ripristino per riavviare il sistema se il computer si blocca e non riesce ad eseguire un normale riavvio.

ASRock FM2A85X Extreme4-M Motherboard

Page 67

PLED (LED alimentazione del sistema):

Va collegato all’indicatore di stato d’alimentazione del pannello frontale del telaio. Il LED è acceso quando il sistema è operativo. Il LED continua a lampeggiare quando il sistema è in stato di standby S1. Il LED è spento quando il sistema è in stato di sospensione /ibernazione S3/S4 oppure spento (S5).

HDLED (LED attività disco rigido):

Va collegato al LED attività disco rigido del pannello frontale del telaio. Il

LED è acceso quando disco rigido legge e scrive i dati.

Il design del pannello frontale può variare in base ai telai. Il modulo di un pannello frontale può consistere di: interruttore d’alimentazione,

interruttore di ripristino, LED d’alimentazione, LED attività disco rigido,

casse, eccetera. Quando si collega il modulo del pannello frontale a

questo header, assicurarsi che l’assegnazione dei li e dei pin sia fatta

corrispondere in modo appropriato.

Collettore casse telaio Collegare le casse del telaio a

(4-pin SPEAKER1)

(vedi p.2 Nr. 21)

questo collettore.

LED di accensione Collegare il LED di accensione

(3-pin PLED1)

(vedi p.2 Nr. 22)

chassi per indicare lo stato di

alimentazione del sistema. Il LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare in stato S1. Il LED è spento in stato S3/S4 o S5 (spegnimento).

Collettori Chassis ed alimentazione ventola Collegare i cavi della ventola ai

(4-pin CHA_FAN1)

(vedi p.2 Nr. 12)

corrispondenti connettori

facendo combaciare il cavo

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

nero col pin di terra.

(3-pin PWR_FAN1) (vedi p.2 Nr. 1

ASRock FM2A85X Extreme4-M Motherboard

Italiano

Page 68

Connettore ventolina CPU Collegare il cavo della ventolina

(4-pin CPU_FAN1)

(vedi p.2 Nr. 5)

CPU a questo connettore e far

combaciare il lo nero al pin

terra.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Sebbene la presente scheda madre disponga di un supporto per ventola CPU a 4 piedini (ventola silenziosa), la ventola CPU a 3 piedini è in grado di funzionare

anche senza la funzione di controllo della velocità della ventola. Se si intende

collegare la ventola CPU a 3 piedini al connettore della ventola CPU su questa scheda madre, collegarla ai piedini 1-3.

Piedini 1-3 collegati

Installazione della ventola a 3 piedini

Italiano

(3-pin CPU_FAN2) (vedi p.2 Nr. 6)

Connettore alimentazione ATX Collegare la sorgente

(24-pin ATXPWR1)

(vedi p.2 Nr. 9)

Con questa scheda madre, c’è in dotazione un

d’alimentazione ATX a questo

connettore.

GND

+12 V

CPU _FAN_ SPEE D

12 124

connettore elettrico ATX a 24 pin, ma può funzionare lo stesso se si adotta un alimentatore ATX a 20 pin. Per usare l’alimentatore ATX a 20 pin, collegare l’alimentatore con il Pin 1 e il Pin 13.

Installazione dell’alimentatore ATX a 20 pin

Connettore ATX 12 V Collegare un alimentatore ATX

(8-pin ATX12V1)

(vedi p.2 Nr. 2)

12 V a questo connettore.

4 8

1 5

ASRock FM2A85X Extreme4-M Motherboard

Page 69

Sebbene questa schedamadre fornisca un connettore elettrico 8-pin ATX 12V, l‘unita‘ puo‘ ancora essere funzionante se viene utilizzata una fornitura elettrica tradizionale a 4-pin ATX 12V. Per usare tale fornitura elettrica 4-pin ATX 12V, prego collegare la presa elettrica al Pin 1 e Pin 5.

4 8

Installazione elettrica 4-Pin ATX 12V

1 5

Collettore porta COM Questo collettore porta COM è

(9-pin COM1)

(vedi p.2 Nr. 30)

utilizzato per supportare il

modulo porta COM.

Header di intrusione dello chassis Questa scheda madre supporta

(2-pin CI1)

la funzione di rilevamento del

(vedi p.2 Nr. 35)

CASE APERTOche rileva che

Sig n al

GND

il coperchio dellochassis è stato rimosso.Questa funzione richiede unochassis con struttura dirilevamento di intrusione dellochassis.

ASRock FM2A85X Extreme4-M Motherboard

Italiano

Page 70

2. Informazioni sul BIOS

La Flash Memory sulla scheda madre contiene le Setup Utility. Quando si avvia il computer, premi <F2> o <Del> durante il Power-On-Self-Test (POST) della Setup utility del BIOS; altrimenti, POST continua con i suoi test di routine. Per entrare il BIOS Setup dopo il POST, riavvia il sistema premendo <Ctl> + <Alt> + <Delete>, o premi il tasto di reset sullo chassis del sistema. Per informazioni più dettagliate circa

il Setup del BIOS, fare riferimento al Manuale dell’Utente (PDF le) contenuto nel cd

di supporto.

3. Software di supporto e informazioni su

Questa scheda madre supporta vari sistemi operativi Microsoft® Windows®: 8 / 8 64bit / 7 / 7 64-bit / VistaTM / Vista

madre contiene i driver e utilità necessari a potenziare le caratteristiche della

scheda. Inserire il CD di supporto nel lettore CD-ROM. Se la funzione “AUTORUN”

è attivata nel computer, apparirà automaticamente il Menù principale. Se il Menù principale non appare automaticamente, posizionarsi sul le “ASSETUP.EXE” nel

CESTINO del CD di supporto e cliccare due volte per visualizzare i menù.

64-bit. Il CD di supporto a corredo della scheda

Italiano

ASRock FM2A85X Extreme4-M Motherboard

Page 71

1. Introducción

Gracias por su compra de ASRock FM2A85X Extreme4-M placa madre, una placa

de conanza producida bajo el control de calidad estricto y persistente. La placa

madre provee realización excelente con un diseño robusto conforme al compromiso de calidad y resistencia de ASRock. Esta Guía rápida de instalación contiene una introducción a la placa base y una guía de instalación paso a paso. Puede encontrar una información más detallada sobre la placa base en el manual de usuario incluido en el CD de soporte.

Porque las especicaciones de la placa madre y el software de BIOS

podrían ser actualizados, el contenido de este manual puede ser cambiado

sin aviso. En caso de cualquier modicación de este manual, la versión

actualizada estará disponible en el website de ASRock sin previo aviso.

También encontrará las listas de las últimas tarjetas VGA y CPU soportadas

en la página web de ASRock. Website de ASRock http://www.asrock.com Si necesita asistencia técnica en relación con esta placa base, visite nuestra

página web con el número de modelo especíco de su placa.

www.asrock.com/support/index.asp

1.1 Contenido de la caja

Placa base ASRock FM2A85X Extreme4-M (Factor forma Micro ATX) Guía de instalación rápida de ASRock FM2A85X Extreme4-M CD de soporte de ASRock FM2A85X Extreme4-M Cuatro cables de datos Serial ATA (SATA) (Opcional) Una protección I/O

ASRock le recuerda...

Para mejorar el rendimiento en Windows® 8 / 8 64 bits / 7 / 7 64 bits / Vis-

/ VistaTM 64 bits, es recomendable establecer la opción del BIOS de

la conguración de almacenamiento en el modo AHCI. Para obtener detalles sobre la conguración del BIOS, consulte el “Manual del usuario”

que se encuentra en nuestro CD de soporte.

ASRock FM2A85X Extreme4-M Motherboard

Español

Page 72

Español

1.2 Especicación

Plataforma - Factor forma Micro ATX

- Todo diseño de Capacitor Sólido (condensadores de polímero conductor de alta calidad 100% fabricados en Japón) Procesador - Admite procesadores de 100 W para zócalo FM2

- Diseño de fases de potencia 4 + 2

- Con soporte para tecnología Cool ‘n’ QuietTM de AMD

- UMI-Link GEN2

Chipset - AMD A85X (Hudson-D4) Memoria - Soporte de Tecnología de Memoria de Doble Canal

- 4 x DDR3 DIMM slots

- Apoya DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/ 1333/1066/800 non-ECC, memoria de un-buffered

- Máxima capacidad de la memoria del sistema: 64GB

- Compatible con Intel® Extreme Memory Prole (XMP)1.3/1.2

- Compatible con AMD Memory Prole (AMP)

Ranuras de - 2 x ranuras PCI Express 2.0 x16 (PCIE1: modo x16; PCIE2: Expansión modo x4)

- 1 x ranura PCI Express 2.0 x1

- 1 x ranura PCI

- Admite CrossFireXTM cuádruple de AMD, CrossFireXTM y

tarjeta gráca dual

VGA OnBoard - Tarjeta gráca AMD Radeon HD 7000

- DirectX 11, Pixel Shader 5.0

- 2GB de Memoria máxima compartida

- Tres opciones de salida VGA: D-Sub, DVI-D y HDMI

- Admite HDMI 1.4a con una resolución máxima de 1920x1200 a 60 Hz

- Admite Dual-link DVI con una resolución máxima de 2560x1600 a 75 Hz

- Admite D-Sub con una resolución máxima de 1920x1600 a 60 Hz

- Admite Sincronización automática entre audio y vídeo, Deep Color (12 bpc), xvYCC y HBR (audio de alta tasa de bits) con HDMI

- Admite la 3D estereoscópica Blu-ray con HDMI 1.4a

- Admite AMD Steady VideoTM 2.0: Nueva capacidad de pospro cesamiento de vídeo para reducción automática de

oscila ciones en vídeo doméstico y en línea

ASRock FM2A85X Extreme4-M Motherboard

Page 73

- Admite la HDCP con puertos DVI y HDMI

- Apoya la reproducción de Blu-rayo de 1080p (BD) / HD-DVD con puertos DVI y HDMI Audio - 7.1 CH HD Audio con Protección de Contenido (Realtek ALC892 Audio Codec)

- Compatible con audio Blu-ray de alta calidad LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Soporta Wake-On-LAN

- Admite detección de conexión de cable LAN

- Compatible con Ethernet 802.3az de bajo consumo

energético

- Compatible con PXE Entrada/Salida I/O Panel de Panel - 1 x puerto de ratón/teclado PS/2 Trasero - 1 x Puerto D-Sub

- 1 x Puerto DVI-D

- 1 x puerto HDMI

- 1 x puerto de salida óptica SPDIF

- 4 x puertos USB 2.0 predeterminados

- 1 x Conector eSATA3

- 2 x puertos USB 3.0 predeterminados

- 1 x Puerto LAN RJ-45 con LED (LED de ACCIÓN/ENLACE y LED de VELOCIDAD)

- Conexión de audio: Altavoz trasero / Central/Bajos / Entrada de línea / Altavoz frontal / Micrófono SATA3 - 7 x conectores SATA3 de 6,0 Gb/s compatibles con RAID (RAID 0, RAID 1, RAID 5 y RAID 10), NCQ, AHCI y de Hot Plug USB 3.0 - 2 x puertos USB 3.0 traseros, compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s

- 1 x cabecera USB 3.0 delantera (compatible con 2 puertos USB 3.0), compatible con USB 1.1/2.0/3.0 de hasta 5 GB/s Conectores - 7 x conexiones SATA3, admiten una velocidad de transferencia de datos de hasta 6,0Gb/s

- 1 x Cabezal de Módulo Infrarrojos

- 1 x Base de conexiones del módulo de infrarrojos para el consumidor

- 1 x cabecera de puerto de impresora

- 1 x En-tête de port COM

Español

ASRock FM2A85X Extreme4-M Motherboard

Page 74

Español

- 1 x Conector de detección de intrusión en el chasis

- 2 x Conector de ventilador de CPU (1 x 4-pin, 1 x 3-pin)

- 1 x Conector de ventilador de chasis (4-pin)

- 1 x Conector de ventilador de alimentacion (3-pin)

- Conector de ventilador de CPU / chasis / alimentacion

- 24-pin cabezal de alimentación ATX

- 8-pin conector de ATX 12V power

- Conector de audio de panel frontal

- 3 x Cabezal USB 2.0 (admite 6 puertos USB 2.0 adicionales)

- 1 x Cabezal USB 3.0 (admite 2 puertos USB 3.0 adicionales) BIOS - 64Mb AMI BIOS legal UEFI AMI compatible con GUI

- Soporta “Plug and Play”

- ACPI 1.1 compliance wake up events

- Soporta “jumper free setup”

- Soporta SMBIOS 2.3.1

- Múltiple ajuste deDRAM, APU PCIE VDDP, CPU y CPU NB/GFX Voltage CD de soport - Controladores, Utilerías, Software de Anti Virus (Versión de prueba), Prueba de CyberLink MediaEspresso 6.5, Google Chrome Browser y Toolbar Monitor - Sensibilidad a la temperatura del procesador Hardware - Sensibilidad a la temperatura de la placa madre

- Taquimetros de los ventiladores del procesador y del CPU / chasis / alimentacion

- Ventilador silencioso del procesador y el chasis

- Control de ajuste de la velocidad del ventilador de la CPU y el chasis

- Control de APERTURA DE CARCASA

- Monitor de Voltaje: +12V, +5V, +3.3V, Vcore OS - En conformidad con Microsoft® Windows® 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / VistaTM 64 bits Certicaciones - FCC, CE, WHQL

- Cumple con la directiva ErP/EuP (se requiere una fuente de alimentación que cumpla con la directiva ErP/EuP)

* Para más información sobre los productos, por favor visite nuestro sitio web: http://www.asrock.com

ASRock FM2A85X Extreme4-M Motherboard

Page 75

1.3 Setup de Jumpers

La ilustración muestra como los jumpers

son congurados. Cuando haya un jumper-

cap sobre los pins, se dice gue el jumper está “Short”. No habiendo jumper cap sobre los pins, el jumper está “Open”. La ilustración muesta un jumper de 3 pins cuyo pin 1 y pin 2 están “Short”.

Jumper Setting

Limpiar CMOS

(CLRCMOS1, jumper de 3 pins) (ver p.2, No. 25)

Nota:

CLRCMOS1 permite borrar los datos de la memoria CMOS. Para borrar los parámetros del sistema y restablecer la conguración predeterminada de los mismos, apague el equipo y desenchufe el cable de alimentación de la toma de corriente

eléctrica. Deje que transcurran 15 segundos y, después, utilice un puente

cortocircuitar los contactos 2 y 3 de CLRCMOS1 durante 5 segundos. No borre

la memoria CMOS justamente después de actualizar el BIOS. Si necesita borrar la memoria CMOS justamente después de actualizar el BIOS, debe iniciar primero

el sistema y, a continuación, cerrarlo antes de llevar a cabo el borrado de dicha memoria. Tenga en cuenta que la contraseña, la fecha, la hora, el perl predeterminado del usuario, el GUID 1394 y la dirección MAC solamente se borrará si la batería CMOS se quita.

Valor predeterminado

Restablecimiento de

la CMOS

para

Si borra la memoria CMOS, se puede detectar un caso de abertura.Ajuste

la opción del BIOS “Clear Status” (Borrar estado) para borrar elregistro del estado de intrusión anterior del chasis.

ASRock FM2A85X Extreme4-M Motherboard

Español

Page 76

1.4 Cabezales y Conectores en Placas

Los conectores y cabezales en placa NO son puentes. NO coloque las cubiertas de los puentes sobre estos cabezales y conectores. El colocar cubiertas de puentes sobre los conectores y cabezales provocará un daño permanente en la placa base.

Conexiones de serie ATA3 Estas siete conexiones de

(SATA3_1: vea p.2, N. 18)

(SATA3_2: vea p.2, N. 19)

(SATA3_3: vea p.2, N. 20)

(SATA3_4: vea p.2, N. 17)

(SATA3_5: vea p.2, N. 16)

(SATA3_7: vea p.2, N. 15)

(SATA3_8: vea p.2, N. 14)

serie ATA3 (SATA3) admiten cables SATA para dispositivos de almacenamiento internos. La

SATA3_7 SATA3_5 SATA3_4

interfaz SATA3 actual permite una velocidad de transferencia de 6.0 Gb/s.

SATA3_3 SATA3_2 SATA3_1

Cable de datos de Cualquier extremo del cable de serie ATA (SATA) los datos de SATA puede ser

(Opcional)

conectado con el disco duro de SATA3 o el conectador de SATA3 en esta placa base.

SATA3_8

Español

Cabecera de puerto de impresora Esta es una interfaz de puerto

(LPT1 de 25 terminales)

(vea p.2, N. 29)

permite conectar cómodamente

dispositivos de impresión.

Cabezal USB 2.0 Además de cuatro puertos USB

(9-pin USB5_6)

(vea p.2, N. 24)

2.0 predeterminados en el panel de E/S, hay tres bases de

conexiones USB 2.0 en esta placa base. Cada una de estas

AFD #

para cable de impresora que

ERR OR#

PIN I T#

SLI N #

SPD 2

SPD 1

SPD 0

STB #

SPD 3

USB _PWR

SPD 4

GND

SPD 7

SPD 6

ACK #

SPD 5

BUS Y

SLC T

P-6

P+6

GND

DUM MY

GND

P+5

P-5

bases de conexiones admite dos puertos USB 2.0.

ASRock FM2A85X Extreme4-M Motherboard

Page 77

(9-pin USB7_8) (vea p.2, N. 26)

(9-pin USB9_10) (vea p.2, N. 28)

USB _PWR

P-8

P-7

P-1 0

P-9

P+8

P+7

P+1 0

P+9

GND

DUM MY

Cabezal USB 3.0 Además de dos puertos 3.0

(19-pin USB3_3_4)

(vea p.2, N. 10)

predeterminados situados en el

panel E/S, encontrará una cabecera USB 3.0 en esta placa base. Esta cabecera USB

3.0 admiten dos puertos USB

3.0.

Vbu s

Int A_P3 _SSR X-

Int A_P3 _SSR X+

GND

Int A_P3 _SST X-

Int A_P3 _SST X+

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

Cabezal de Módulo Infrarrojos Este cabezal soporta un módulo

(5-pin IR1)

infrarrojos de transmisión y

(vea p.2, N. 31)

recepción wireless opcional.

Base de conexiones del módulo de Esta base de conexiones se infrarrojos para el consumidor puede utilizar para conectar

(4-pin CIR1)

(vea p.2, N. 27)

Conector de audio de Este es una interface para panel frontal cable de audio de panel frontal

(9-pin HD_AUDIO1)

(vea p.2, N. 32)

Audio.

receptor remoto.

GND

PRE SENC E#

MIC _RET

OUT _RET

que permite conexión y control

conveniente de apparatos de

MIC 2_L

OUT 2_R

MIC 2_R

OUT 2_L

J_S ENSE

Español

ASRock FM2A85X Extreme4-M Motherboard

Page 78

1. El Audio de Alta Denición soporta la detección de conector, pero el

cable de panel en el chasis debe soportar HDA para operar correctamente. Por favor, siga las instrucciones en nuestro manual y en el manual de chasis para instalar su sistema.

2. Si utiliza el panel de sonido AC’97, instálelo en la cabecera de sonido del panel frontal de la siguiente manera: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) en OUT2_L. C. Conecte Ground (GND) a Ground (GND).

D. MIC_RET y OUT_RET son sólo para el panel de sonido HD. No necesitará conectarlos al panel de sonido AC’97.

E. Activación del micrófono frontal.

En sistemas operativos Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit:

Acceda a la cha “FrontMic” (Micrófono frontal) del panel de control Realtek. Ajuste la posición del control deslizante “Recording Volume” (Volumen de grabación).

Cabezal de panel de sistema Este cabezar acomoda varias

(9-pin PANEL1)

(vea p.2, N. 23)

dunciones de panel frontal de

sistema.

Español

Conecte el interruptor de alimentación, el interruptor de restablecimiento y el indicador de estado del sistema situados en el chasis con esta cabecera en función de las siguientes asignaciones de contacto. Preste atención a los contactos positivos y negativos antes de conectar los cables.

PWRBTN (interruptor de alimentación):

Conecte el interruptor de encendido situado en el panel frontal del

chasis. Puede congurar la forma de apagar su sistema mediante el

interruptor de alimentación.

RESTABLECER (interruptor de restablecimiento):

Conecte el interruptor de restablecimiento situado en el panel frontal del chasis. Pulse el interruptor de restablecimiento para restablecer el equipo si se bloquea y no se reinicia con normalidad.

ASRock FM2A85X Extreme4-M Motherboard

Page 79

PLED (LED de alimentación del sistema):

Conecte el indicador de estado de alimentación situado en el panel

frontal del chasis. El LED se enciende cuando el sistema esté en

funcionamiento. El LED parpadea cuando el sistema se encuentre en estado de suspensión S1. El LED se apaga cuando el sistema se encuentre en estado de suspensión S3/S4 o se apaga (S5).

HDLED (LED de actividad del disco duro):

Conecte el LED de actividad de disco duro situado en el panel frontal

del chasis. El LED se enciende cuando el disco duro esté leyendo o

escribiendo datos.

Es posible que el diseño del panel frontal varíe en función del chasis. Un módulo del panel frontal consiste principalmente de interruptor de alimentación, interruptor de restablecimiento, LED de alimentación, LED de actividad del disco duro, altavoz, etc. Al conectar el módulo del panel

frontal del chasis a esta cabecera, asegúrese de que las asignaciones

de cables y las asignaciones de contactos coincidan correctamente.

Cabezal del altavoz del chasis Conecte el altavoz del chasis a

(4-pin SPEAKER1)

(vea p.2, N. 21)

su cabezal.

Cabecera de indicador Conecte el indicador LED de LED de encendido encendido del chasis a esta

(3-pin PLED1)

(vea p.2, N. 22)

cabecera para conocer el

estado de encendido del sistema. El indicador LED se encenderá si el sistema se encuentra en funcionamiento. El indicador LED parpadeará en el estado S1. El indicador LED se apagará en los estados S3/S4 o S5 (apagado).

ASRock FM2A85X Extreme4-M Motherboard

Español

Page 80

Conectores de ventilador de Por favor, conecte los cables chasis / alimentación del ventilador a los conectores

(4-pin CHA_FAN1)

(vea p.2, N. 12)

(3-pin PWR_FAN1) (vea p.2, N. 1)

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

de ventilador, haciendo coincidir el cable negro con la patilla de masa.

Español

Conector del ventilador Conecte el cable del ventilador de la CPU de la CPU a este conector y

(4-pin CPU_FAN1)

(vea p.2, N. 5)

haga coincidir el cable negro

con el conector de tierra.

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Aunque esta placa base proporciona compatibilidad para un ventilador (silencioso) de procesador de 4 contactos, el ventilador de procesador de 3 contactos seguirá funcionando correctamente incluso sin la función de control de velocidad de ventilador. Si pretende enchufar el ventilador de procesador de 3 contactos en el

conector del ventilador de procesador de esta placa base, conéctelo al contacto

1-3.

Contacto 1-3 conectado

Instalación del ventilador de 3 contactos

(3-pin CPU_FAN2) (vea p.2, N. 6)

Cabezal de alimentación ATX Conecte la fuente de

(24-pin ATXPWR1)

(vea p.2, N. 9)

A pesar de que esta placa base incluye in conector

de alimentación ATX de 24 pins, ésta puede funcionar

alimentación ATX a su cabezal.

GND

+12 V

CPU _FAN_ SPEE D

12 124

incluso si utiliza una fuente de alimentación ATX de 20 pins tradicional. Para usar una fuente de alimentación ATX de 20 pins, por favor, conecte su fuente de alimentación usando los Pins 1 y 13.

Instalación de una Fuente de Alimentación ATX de 20 Pins

ASRock FM2A85X Extreme4-M Motherboard

Page 81

Cabezal de alimentación ATX 12V Conecte la fuente de

(4-pin ATX12V1)

(vea p.2, N. 2)

4 8

1 5

alimentación ATX 12V a su cabezal.

Aunque esta placa base proporciona un conector de energía de 8-pin ATX 12V, puede todavía trabajar si usted adopta un fuente tradicional de energía de 4-pin ATX 12V. Para usar el fuente de energía de 4-pin ATX 12V, por favor conecte su fuente de energía junto con Pin 1 y Pin 5.

4 8

Instalación de Fuente de Energía de 4-Pin ATX 12V

1 5

Cabezal del puerto COM Este cabezal del puerto COM

(9-pin COM1)

(vea p.2, N. 30)

se utiliza para admitir un

módulo de puerto COM.

Conector de detección de Esta placa base admite la intrusión en el chasis función de control de

(2-pin CI1)

APERTURA DE CARCASA,

(vea p.2, N. 35)

quepermite detectar si se

Sig n al

GND

haretirado la cubierta del chasis.Dicha función requiere unchasis con diseño

especícopara la detección de

intrusiónen el chasis.

ASRock FM2A85X Extreme4-M Motherboard

Español

Page 82

2. BIOS Información

El Flash Memory de la placa madre deposita SETUP Utility. Durante el Power-Up (POST) apriete <F2> o <Del> para entrar en la BIOS. Sí usted no oprime ninguna

tecla, el POST continúa con sus rutinas de prueba. Si usted desea entrar en la BIOS después del POST, por favor reinicie el sistema apretando <Ctl> + <Alt> +

<Borrar>, o apretando el botón Reset en el panel del ordenador. Para información

detallada sobre como congurar la BIOS, por favor reérase al Manual del Usuario

(archivo PDF) contenido en el CD.

3. Información de Software Support CD

Esta placa-base soporta diversos tipos de sistema operativo Windows®: 8 / 8 64 bits / 7 / 7 64 bits / VistaTM / Vista

base trae todos los drivers y programas utilitarios para instalar y congurar la placa-

base. Para iniciar la instalación, ponga el CD en el lector de CD y se desplegará el

Menú Principal automáticamente si «AUTORUN» está habilitado en su computadora. Si el Menú Principal no aparece automáticamente, localice y doble-pulse en el

archivo “ASSETUP.EXE” para iniciar la instalación.

64 bits. El CD de instalación que acompaña la placa-

Español

ASRock FM2A85X Extreme4-M Motherboard

Page 83

1. Введение

Благодарим вас за покупку материнской платы ASRock FM2A85X Extreme4-M надежной материнской платы, изготовленной в соответствии с постоянно предъявляемыми ASRock жесткими требованиями к качеству. Она обеспечивает превосходную производительность и отличается отличной конструкцией, которые отражают приверженность ASRock качеству и долговечности. Данное руководство по быстрой установке включает вводную информацию о материнской плате и пошаговые инструкции по ее установке. Более подробные сведения о плате можно найти в руководстве пользователя на компакт-диске поддержки.

Спецификации материнской платы и программное обеспечение BIOS иногда изменяются, поэтому содержание этого руководства может обновляться без уведомления. В случае любых модификаций руководства его новая версия будет размещена на веб-сайте ASRock без специального уведомления. Кроме того, самые свежие списки поддерживаемых модулей памяти и процессоров можно найти на сайте ASRock. Адрес веб-сайта ASRock http://www.asrock.com При необходимости технической поддержки по вопросам данной материнской платы посетите наш веб-сайт для получения информации об используемой модели.

www.asrock.com/support/index.asp

1.1 Комплектность

Материнская плата ASRock FM2A85X Extreme4-M (форм-фактор Micro ATX) Руководство по быстрой установке ASRock FM2A85X Extreme4-M Компакт-диск поддержки ASRock FM2A85X Extreme4-M 4 x кабель данных Serial ATA (SATA) (дополнительно) 1 x I/O Щит Группы ввода / вывода

ASRock напоминает...

Для обеспечения максимальной производительности ОС Windows

8 / 8 64-bit / 7 / 7 64-bit / Vista

BIOS выбрать для параметра Storage Conguration (Конфигурация запоминающего устройства) режим AHCI. Подробные сведения о настройке BIOS см. в руководстве пользователя на прилагаемом компакт-диске.

/ VistaTM 64-bit рекомендуется в

ASRock FM2A85X Extreme4-M Motherboard

Русский

Page 84

Русский

1.2 Спецификации

Платформа - форм-фактор Micro ATX

- Весь Твердый Конденсаторный проект (высококачественные конденсаторы с проводящим полимером; на 100% сделано в Японии) Процессор - Поддерживаются процессоры для гнезда Socket FM2 с потребляемой мощностью до 100 Вт

- Технология 4 + 2 Power Phase Design

- Поддержка технологии AMD Cool ‘n’ Quiet

- UMI-Link GEN2 Набор микросхем - AMD A85X (Hudson-D4) Память - Поддержка технологии Dual Channel DDR3 Memory Technology

- 4 x гнезда DDR3 DIMM

- Поддержите DDR3 2600+(OC)/2400(OC)/2133(OC)/1866/1600/1333/ 1066/800 не- ECC, безбуферная память

- Mакс. 64 Гб

- поддержка профиля Intel® Extreme Memory Prole (XMP)1.3/1.2

- поддержка профиля AMD Memory Prole (AMP)

Гнезда - 2 x гнезда PCI Express 2.0 x16 (PCIE1: режим x16; PCIE3: режим x4) расширения - 1 x гнезда PCI Express 2.0 x1

- 1 x гнезда PCI

- Поддерживаются режимы AMD Quad CrossFireXTM, CrossFireXTM и двойные видеокарты Графика - Видеоадаптер AMD Radeon HD 7000

- Поддержка DirectX 11, Pixel Shader 5.0

- Макс. объем разделяемой памяти 2GB

- Три VGA-выхода: D-Sub, DVI-D и HDMI

- Поддержка HDMI 1.4a с максимальным разрешением до 1920х1200 @ 60 Гц

- Поддержка Dual-link DVI с максимальным разрешением до 2560х1600 @ 75 Гц

- Поддержка D-Sub с максимальным разрешением до 1920х1600 @ 60 Гц

- Поддержка Auto Lip Sync, Deep Color (12 бит на цветовой канал), xvYCC и HBR (High Bit Rate Audio) через HDMI

- Поддержка стандарта Blu-ray Stereoscopic 3D со спецификацией

HDMI 1.4a

- Поддержка технологии AMD Steady VideoTM 2.0: новая функция постобработки видеоизображения для автоматического устранения дрожания при просмотре домашних и онлайновых видеозаписей

- Поддержка HDCP через разъемы DVI и HDMI

- Подержат Blu-луч 1080p (КОММУТАЦИОННАЯ ДОСКА) / воспроизведение HD-DVD через разъемы DVI и HDMI Аудиосистема - 7.1 CH HD Аудио HD с Довольной Защитой (Кодер-декодер Аудио Realtek ALC892)

- Поддержка Premium Blu-ray audio

ASRock FM2A85X Extreme4-M Motherboard

Page 85

ЛВС - PCIE x 1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- поддержка Wake-On-LAN

- Поддержка определения кабеля ЛВС

- Поддержка энергосберегающего интерфейса Ethernet 802.3az

- Поддержка PXE

Разъемы ввода- I/O Panel вывода на задней - 1 x порт мыши/клавиатуры PS/2 панели - 1 x D-Sub порт

- 1 x DVI-D порт

- 1 x HDMI порт

- 1 x порт Optical SPDIF Out

- 4 x порта USB 2.0 на задней панели в стандартной конфигурации

- 1 x eSATA3 порт

- 2 x порта USB 3.0 на задней панели в стандартной конфигурации

- Разъем 1 x RJ-45 LAN с светодиодным индикатором (индикатор ACT/LINK и индикатор SPEED)

- Соединитель звуковой подсистемы: тыльная колонка / центральная / субвуфер / линейный вход / передняя колонка / микрофон SATA3 - 7 x разъема SATA3 6,0 Гбит/с, поддержка RAID (RAID 0, RAID 1, RAID 5 и RAID 10), NCQ, AHCI и горячего подключения USB 3.0 - 2 x задних порта USB 3.0 на контроллере с поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с

- 1 x передний разъем USB 3.0 (поддерживает 2 порта USB 3.0) с поддержкой интерфейсов USB 1.1/2.0/3.0 и скорости передачи данных до 5 Гбит/с

Колодки и - 7 x разъема SATA3 6,0 Гбит/с плате - 1 x Колодка инфракрасного модуля

- 1 x Датчик пользовательского инфракрасного модуля

- 1 x Разъем порта печати

- 1 x Колодка COM

- 1 x разъем Power LED

- 1 x разъем датчика открытой крышки

- 2 x соединитель CPU FAN (1 x 4-контактный, 1 x 3-контактный)

- 1 x соединитель Chassis FAN (4-контактный)

- 1 x соединитель Power FAN (3-контактный)

- 24-контактный Колодка питания ATX

- 8-контактный Разъем ATX 12 В

- Аудиоразъем передней панели

- 3 x Колодка USB 2.0 (одна колодка для поддержки 6 дополнительных портов USB 2.0

- 1 x Колодка USB 3.0 (одна колодка для поддержки 2 дополнительных портов USB 3.0) BIOS - 64Mb AMI UEFI Legal BIOS с поддержкой rpaфичеckoro интеpфeйca поль зователя

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 86

- поддержка “Plug and Play”

- ACPI 1.1, включение по событиям

- поддержка режима настройки без перемычек

- поддержка SMBIOS 2.3.1

- Регулировка напряжений DRAM, APU PCIE VDDP, CPU и CPU

NB/GFX Компакт диск - Драйверы, Утилиты, Антивирус (пробная версия), Пробная версия поддержки программы CyberLink MediaEspresso 6.5, Google Chrome Browser и Toolbar Контроль - Датчики температуры процессора оборудования - Датчики температуры корпуса

- Тахометры вентиляторов CPU/Chassis/Power FAN

- Бесшумный вентилятор ЦП/системного блока

- Мультиконтроль скорости вентилятора ЦП/Шасси

- Определение открытой крышки

- Контроль напряжения: +12V, +5V, +3.3V, Vcore

Операцион - Совместимость с Microsoft® Windows® 8 / 8 64-bit / 7 / 7 64-bit / Vista ные системы - FCC, CE, WHQL Сертификаты - Совместимость с ErP/EuP Ready (требуется блок питания

совместимый с ErP/EuP) * Для детальной информации продукта, пожалуйста посетите наш вебсайт:

http://www.asrock.com

/ Поддержка 64-разрядной версии VistaTM

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 87

1.3 Установка перемычек

Конфигурация перемычек иллюстрируется на рисунке. Когда перемычка надета на контакты, они называются “замкнутыми” (short). Если на контактах перемычки нет, то они называются “разомкнутыми” (open). На иллюстрации показана 3-контактная перемычка, у которой контакты 1 и 2 замкнуты.

Перемычка Установка Описание

Очистка CMOS

(CLRCMOS1,

3-контактная перемычка) (см. стр. 2, п. 25)

Стандартные Очистка CMOS

Примечание.

Очистка CMOS может вызвать срабатывание датчика открытой

Контактная колодк а CLRCMOS1 позволяет очистить данн ые CMOS . Для очистки данных и восстановления заводских системных параметров сначала вы кл ючите компьютер и отсоедините сетевую вилку кабел я пи та ни я от электророзетки. Выждите не менее 15 секунд и колпачковой перемычкой на 5 секунд перемкните штырьки 2 и 3 контактной колодки CLRCMOS1. Однако не производите очистку CMOS непосредственно после обновления BIOS. Если необходимо очистить CMOS сразу же после окончания обновления BIOS, то, перед очисткой CMOS, необходимо сначала выполнить загрузку системы, а затем завершить ее работу. Примите во внимание, что пароль, дата, время, профиль пользователя по умолчанию, идентификатор 1394 GUID и MAC-адрес будут очищены только тогда, когда будет извлечена из своего гнезда батарейка

CMOS.

крышки. Измените опцию «Clear Status» в BIOS, чтобы очистить записи о предыдущих срабатываниях датчика.

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 88

1.4 Колодки и разъемы на плате

Имеющиеся на плате колодки и разъемы НЕ ЯВЛЯЮТСЯ контактами для перемычек. НЕ УСТАНАВЛИВАЙТЕ перемычки на эти колодки и разъемы – это приведет к необратимому повреждению материнской платы!

Разъемы Serial ATA3 семь соединителя Serial ATA3

(SATA3_1, см. стр. 2, п. 18) (SATA3_2, см. стр. 2, п. 19) (SATA3_3, см. стр. 2, п. 20) (SATA3_4, см. стр. 2, п. 17) (SATA3_5, см. стр. 2, п. 16) (SATA3_7, см. стр. 2, п. 15) (SATA3_8, см. стр. 2, п. 14)

Гбит/с.

предназначаются для подключения внутренних устройств хранения с

SATA3_7 SATA3_5 SATA3_4

использованием интерфейсных кабелей SATA3. В настоящее время интерфейс SATA допускает скорость передачи данных до \ 6,0

SATA3_3 SATA3_2 SATA3_1

SATA3_8

Информационный Информационный кабель кабель Serial ATA (SATA) интерфейса SATA3 не является

(дополнительно)

направленным. Любой из его соединителей может быть подключен либо к жесткому диску интерфейса SATA3 либо к материнской плате.

Разъем порта печати Это интерфейс кабеля порта

(25-выводов LPT1) (см. cтр. 2, п. 29)

подключение принтеров.

AFD #

ERR OR#

PIN I T#

печати, обеспечивающий удобное

SLI N #

SPD 2

SPD 1

SPD 0

STB #

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

SLC T

Русский

Колодка USB 2.0 Помимо четыре стандартных

(9-контактный USB5_6) (см. стр. 2, п. 24)

портов USB 2.0 на панели ввода-

вывода,на данной материнской плате предусмотрено три разъема USB 2.0. Каждый разъем USB 2.0 поддерживает два порта USB 2.0.

USB _PWR

P-6

P+6

GND

DUM MY

GND

P+5

P-5

ASRock FM2A85X Extreme4-M Motherboard

Page 89

(9-контактный USB7_8) (см. стр. 2, п. 26)

(9-контактный USB9_10) (см. стр. 2, п. 28)

USB _PWR

P-8

P-7

P-1 0

P-9

P+8

P+7

P+1 0

P+9

GND

DUM MY

Колодка USB 3.0 Помимо два стандартных портов

(19-контактный USB3_3_4) (см. стр. 2, п. 10)

USB 3.0 на панели ввода- вывода,

на данной материнской плате

предусмотрен один разъем USB

3.0. Этот разъем USB 3.0 поддерживает два порта USB 3.0.

Vbu s

Int A_P3 _SSR X-

Int A_P3 _SSR X+

GND

Int A_P3 _SST X-

Int A_P3 _SST X+

GND

Int A_P3 _D-

Int A_P3 _D+

Vbu sVbu s

Int A_P4 _SSR X-

Int A_P4 _SSR X+

GND

Int A_P4 _SST X-

Int A_P4 _SST X+

GND

Int A_P4 _D-

Int A_P4 _D+

DUM MY

Колодка инфракрасного модуля Данная колодка позволяет

(5-контактный IR1) (см. стр. 2, п. 31)

подключить дополнительный

модуль беспроводного инфракрасного приемопередатчика.

Датчик пользовательского инфракрасного модуля Датчик можно использовать для

(4-контактный CIR1) (см. стр. 2, п. 27)

Аудиоразъем передней Этот интерфейс предназначен панели для присоединения аудиокабеля

(9-контактный HD_AUDIO1) (см. cтр. 2, п. 32)

подключение аудиоустройств и управление ими.

подключения дистанционный

приемник.

GND

PRE SENC E#

MIC _RET

MIC 2_R

MIC 2_L

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

передней панели,

обеспечивающего удобное

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 90

1. Система High Denition Audio поддерживает функцию автоматического обнаружения разъемов (Jack Sensing), однако для ее правильной pаботы кабель панели в корпусе должен поддерживать HDA. При сборке системы следуйте инструкциям, приведенным в нашем руководстве и руководстве пользователя для корпуса.

2. Если вы используете аудиопанель AC’97, подключите ее к колодке аудиоинтерфейса передней панели следующим образом: A. Подключите выводы Mic_IN (MIC) к контактам MIC2_L. B. Подключите выводы Audio_R (RIN) к контактам OUT2_R, а выводы Audio_L (LIN) к контактам OUT2_L. C. Подключите выводы Ground (GND) к контактам Ground (GND). D. Контакты MIC_RET и OUT_RET предназначены только для аудиопанели HD. При использовании аудиопанели AC’97 подключать их не нужно.

E. Процедура активации микрофона приведена ниже.

Для ОС Windows® 8 / 8 64-бита / 7 / 7 64-бита / VistaTM / VistaTM 64-бита:

Перейдите к вкладке «FrontMic» (Передний микрофон) в панели управления Realtek. Отрегулируйте уровень «Recording Volume» (Громкость записи).

Колодка системной панели Данная колодка обеспечивает

(9-контактный PANEL1) (см. стр. 2, п. 23)

работу нескольких функций

передней панели системы.

Русский

Подключите к этому разъему кнопку питания, кнопку сброса и индикатор состояния системы на корпусе в соответствии с указанным ниже назначением контактов. При подключении кабелей необходимо соблюдать полярность положительных и отрицательных контактов.

PWRBTN (кнопка питания):

Подключите к этим контактам кнопку питания на передней панели корпуса. Способ выключения системы с помощью кнопки питания можно настроить.

ASRock FM2A85X Extreme4-M Motherboard

Page 91

RESET (кнопка сброса):

Подключите к этим контактам кнопку сброса на передней панели корпуса. Нажмите кнопку сброса для перезагрузки компьютера, если компьютер «завис» и нормальную перезагрузку выполнить не удается.

PLED (индикатор питания системы):

Подключите к этим контактам индикатор состояния питания на передней панели корпуса. Этот индикатор светится, когда система работает. Индикатор мигает, когда система находится в режиме ожидания S1. Этот индикатор не светится, когда система находится в режиме ожидания S3/S4, либо выключена (S5).

HDLED (индикатор активности жесткого диска):

Подключите к этим контактам индикатор активности жесткого диска на передней панели корпуса. Этот индикатор светится, когда осуществляется считывание или запись данных на жестком диске.

Конструкция передней панели может различаться в зависимости от корпуса. Модуль передней панели в основном состоит из кнопки питания, кнопки сброса, индикатора питания, индикатора активности жесткого диска, динамика и т.п. При подключении к этому разъему модуля передней панели корпуса удостоверьтесь, что провода подключаются к соответствующим контактам.

Колодка динамика корпуса Подключите к этой колодке

(4-контактный SPEAKER1) (см. стр. 2, п. 21)

кабель от динамика на корпусе

компьютера.

разъем Power LED Подключите индикатор Power LED

(3-контактный PLED1) (см. стр. 2, п. 22)

светодиод продолжит мигать в режиме S1. Светодиод будет выключен в режимах S3/S4 или S5 (система выключена).

к этому разъему для отображения

статуса питания системы. Этот

ASRock FM2A85X Extreme4-M Motherboard

Русский

Page 92

Chassis и Power Fan-соединители Подключите кабели вентилятора к

(4-контактный CHA_FAN1) (см. стр. 2, п. 12)

(3-контактный PWR_FAN1) (см. стр. 2, п. 1)

соединителям и присоедините

CHA _FAN _SPE ED

+12 V

FAN _SPE ED_C ONTR OL

GND

черный шнур к штырю заземления.

Разъем вентилятора Подключите к этому разъему процессора кабель вентилятора процессора

(4-контактный CPU_FAN1) (см. стр. 2, п. 5)

соответствовал контакту земли.

так, чтобы черный провод

FAN_ SPEE D_CO NTRO L

CPU _FAN_ SPEE D

+12 V

GND

1 2 3 4

Данная материнская плата поддерживает вентиляторы процессора с 4-контактным разъемом (функция тихого режима вентилятора), однако вентиляторы с 3-контактным разъемом также будут успешно работать, хотя функция управления скоростью вращения вентилятора окажется недоступной. Если вы хотите подключить вентилятор процессора с 3-контактным разъемом к разъему вентилятора процессора на данной материнской плате, для этого следует использовать контакты 1-3.

Контакты 1-3 подключены

Установка вентилятора с 3-контактным разъемом

(3-контактный CPU_FAN2) (см. стр. 2, п. 6)

Колодка питания ATX Подключите к этой колодке

(24-контактный ATXPWR1) (см. стр. 2, п. 9)

кабель питания ATX.

GND

+12 V

12 124

CPU _FAN_ SPEE D

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 93

Несмотря на то, что эта материнская плата предусматр ивает 24-штыревой разъем питания ATX, работа будет продолжаться, даже если адаптируется традиционный 20-штыревой разъем питания ATX. Для использования 20-штыревого разъема питания ATX вставьте источник питания вместе со штекером 1 и штекером 13.

Установка 20-штыревого разъема питания ATX

Колодка питания 12V-ATX Подключите к этой колодке

(8-контактный ATX12V1) (см. стр. 2, п. 2)

4 8

1 5

кабель питания ATX 12V.

Хотя эта объединительная плата обеспечивает ATX с 8 булавкам и 12V соединитель власти, это может все еще работать, если Вы принимаете традиционный ATX с 4- Pi n 12V эл ек тр опитание. Чтобы испол ьзовать электропитание ATX с 4-Pin, пожалуйста включите ваше электропитание наряду с Булавкой 1 и Прикрепите 5.

4 8

ATX С 4-Pin 12V Установка Электропитания

1 5

Колодка COM-порта Данная колодка COM-порта

(9-контактный COM1) (см. стр. 2, п. 30)

позволяет подключить модуль

порта COM.

Датчик открытой крышки Эта материнская плата

(2-контактный CI1) (см. стр. 2, п. 35)

поддерживает функцию

определения открытой крышки,

Sig n al

GND

которая позволяет определить, была ли снята крышка корпуса. Функция требует поддержку со стороны корпуса.

ASRock FM2A85X Extreme4-M Motherboard

Русский

Page 94

2. Информация о BIOS

Утилита настройки BIOS (BIOS Setup) хранится во флэш-памяти на материнской плате. Чтобы войти в программу настройки BIOS Setup, при запуске компьютера нажмите <F2> или <Del> во время самопроверки при включении питания (Power-On-Self-Test – POST). Если этого не сделать, то процедуры тестирования POST будут продолжаться обычным образом. Если вы захотите вызвать BIOS Setup уже после POST, перезапустите систему с помощью клавиш <Ctrl> + <Alt> + <Delete> или нажатия кнопки сброса на корпусе системы. Подробную информацию о программе BIOS Setup вы найдете в Руководстве пользователя (в формате PDF) на компакт-диске поддержки.

3. Информация о компакт-диске поддержки с программным обеспечением

Данная материнская плата поддерживает различные операционные системы Microsoft®

Windows®: 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit. Поставляемый вместе с ней

компакт-диск поддержки содержит необходимые драйверы и полезные утилиты, которые расширяют возможности материнской платы. Чтобы начать работу с компакт-диском поддержки, вставьте его в дисковод CD-ROM. Если в вашем компьютере включена функция автозапуска (AUTORUN), то на экране автоматически появится главное меню компакт-диска (Main Menu). Если этого не произошло, найдите в папке BIN на компакт-диске поддержки файл ASSETUP.EXE и дважды щелкните на нем, чтобы открыть меню.

Русский

ASRock FM2A85X Extreme4-M Motherboard

Page 95

1. Introdução

Gratos por comprar nossa placa–mãe FM2A85X Extreme4-M um produto conável feito com ASRock um estrito controle de qualidade consistente. Com um excelente

desempenho, essa placa é dotada de um projeto robusto que atende a ASRock de

compromisso com a qualidade e durabilidade. Este Guia de Instalação Rápida apresenta a placa-mãe e o guia de instalação passo a passo. Mais informações detalhadas sobre a placa-mãe podem ser encontradas no manual do usuário do CD de suporte.

ser atualizados, o conteúdo deste manual pode ser cambiado sem aviso. Em caso de qualquer modicação deste manual, a versão atualizada estará disponível no website de ASRock sem prévio aviso. Pode também

encontrar as listas das mais recentes placas VGA e das CPUs suportadas no site da web da ASRock. Website de ASRock http://www.asrock.com Se precisar de apoio técnico em relação a este placa-mãe, por favor visite

o nosso sítio da internet para informação especíca acerca do modelo que

está a utilizar. www.asrock.com/support/index.asp

Porque as especicações da placa mãe e o software de BIOS poderiam

1.1 Este pacote contém

Placa-mãe ASRock FM2A85X Extreme4-M (Formato Micro ATX) Guia de instalação rápida da ASRock FM2A85X Extreme4-M CD de suporte da placa ASRock FM2A85X Extreme4-M Quatro cabo de dados ATA Serial (SATA) (Opcional) Uma proteção I/O

A ASRock recorda-lhe...

Para obter melhor desempenho em Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit, recomendamos que dena a opção Conguração de Armazenamento na BIOS para o modo AHCI. Para mais detalhes

acerca da conguração da BIOS consulte o “Manual de utilizador” no

nosso CD de suporte.

ASRock FM2A85X Extreme4-M Motherboard

Português

Page 96

Português

1.2 Especicações

Plataforma - Formato Micro ATX

- Design de condensadores banhados a ouro de alta qualidade (Condensadores de polímeros condutores de alta qualidade 100% fabricados no Japão) CPU - Suporte para processadores com Socket FM2 de 100W

- Alimentação de 4 + 2 fases

- Suporta a tecnologia Cool ‘n’ Quiet da AMD

- UMI-Link GEN2 Chipsets - AMD A85X (Hudson-D4) Memória - Suporte à tecnologia de memória de duplo canal

- 4 x slots de DDR3 DIMM

- Suporta memória DDR3 2600+(OC)/2400(OC)/2133(OC)/1866 /1600/1333/1066/800, não ECC, sem tampão

- Capacidade máxima de memória do sistema: 64GB

- Suporta Extreme Memory Prole (XMP)1.3/1.2 da Intel

- Suporta Perl de Memória AMD (AMP)

Slots de - 2 x slots de PCI Express 2.0 x16 Expansão (PCIE1: modo x16; PCIE3: modo x4)

- 1 x slot de PCI Express 2.0 x1

- 1 x slot de PCI

- Suporta Quad CrossFireXTM, CrossFireXTM e Dual Graphics da AMD VGA integrado - Placa gráca AMD Radeon HD Série 7000

- DirectX 11, Pixel Shader 5.0

- Memória partilhada máxima 2GB

- Três opções de saída VGA: D-Sub, DVI-D e HDMI

- Suporta HDMI 1.4a Tecnologia com resolução máxima até 1920x1200 @ 60Hz

- Suporta Dual-link DVI com resolução máxima até 2560x1600

@ 75Hz

- Suporta D-Sub com resolução máxima até 1920x1600 @

60Hz

- Suporta as funções Auto Lip Sync (Sincronização automática do som), Deep Color (Profundidade da cor) (12bpc), xvYCC e

HBR (áudio de taxa de bits elevada) com HDMI (é necessário

um monitor compatível com a norma HDMI)

- Suporta 3D Estereoscópico Blu-ray com HDMI 1.4a

- Suporta AMD Steady VideoTM 2.0: Nova capacidade de pós-processamento de vídeo para redução automática de

ASRock FM2A85X Extreme4-M Motherboard

Page 97

vibrações em vídeo local/online

- Suporta função HDCP com portas DVI e HDMI

- Suporta a norma Blu-ray de alta denição 1080p (BD) / e a

reprodução de DVDs de alta denição com portas DVI e HDMI Áudio - Áudio HD de 7.1 canais com protecção de conteúdo

(Realtek ALC892 Audio Codec)

- Suporte áudio Blu-ray superior LAN - PCIE x1 Gigabit LAN 10/100/1000 Mb/s

- Realtek RTL8111E

- Suporta Wake-On-LAN

- Suporta Detecção de cabo LAN

- Suporta Ethernet com Eciência Energética 802.3az

- Suporta PXE Entrada/Saída I/O Panel pelo painel - 1 x porta para teclado/mouse PS/2

- 1 x porta D-Sub

- 1 x porta DVI-D

- 1 x porta HDMI

- 1 x Porta de saída SPDIF óptica

- 4 x portas USB 2.0 padrão

- 1 x Conector eSATA3

- 2 x portas USB 3.0 padrão

- 1 x porta LAN RJ-45 com LED (LED ACT/LIG e LED VELOCIDADE)

- Ficha de áudio HD: Altifalante traseiro/Central/Baixos/Entrada

de linha/Altifalante frontal/Microfone SATA3 - 7 x conectores SATA3 a 6,0 Gb/s, com suporte para RAID (RAID 0, RAID 1, RAID 5 e RAID 10), NCQ, AHCI e funções Hot Plug USB3.0 - 2 x Portas USB 3.0 traseiras, com suporte para USB 1.1/2.0/3.0

até 5Gb/s

- 1 x Conector USB 3.0 frontal (suporta 2 portas USB 3.0), com

suporte para USB 1.1/2.0/3.0 até 5Gb/s

Conectores - 7 x conectores SATA3, suporte a taxa de transferência de

dados de até 6,0 Gb/s

- 1 x Conector do módulo de infravermelho

- 1 x Conector CIR

- 1 x Conector de Porta de Impressão

- 1 x conector de porta COM

Português

ASRock FM2A85X Extreme4-M Motherboard

Page 98

Português

- 1 x Conector para LED de alimentação

- 1 x Conector de intrusão no chassis

- 2 x Conector do ventilador da CPU (1 x 4 pinos, 1 x 3 pinos)

- 1 x Conector do ventilador da chassis (4 pinos)

- 1 x Conector do ventilador da energia (3 pinos)

- Conector de força do ATX de 24 pinos

- Conector ATX 12 V de 8 pinos

- Conector Áudio do painel frontal

- 3 x cabezal USB 2.0 (suporta 6 portas USB 2.0)

- 1 x cabezal USB 3.0 (suporta 2 portas USB 3.0) BIOS - 64Mb BIOS UEFI ocial da AMI com suporte para GUI

- Suporta dispositivos “Plug and Play”

- ACPI 1.1 atendendo a eventos de “wake up”

- Suporta dispositivos sem jumper

- Suporte para SMBIOS 2.3.1

- DRAM, APU PCIE VDDP, CPU e CPU NB/GFX Voltage Multi-adjustment CD de suporte - Controladores, utilitários, software antivírus (Experimentacao Versao), CyberLink MediaEspresso 6.5 versão de demonstração, Navegador Google Chrome e Barra de Ferramentas Monitor do HW - Sensores de temperature do procesador

- Medição de temperatura da placa-mãe

- Tacômetros de ventilador do Processador/chassis/energia

- Ventoinha silenciosa para a CPU/chassis

- CPU/Chassis Fan Controle Multi-Velocidade

- Detecção de ABERTURA da CAIXA

- Monitoramento de voltagem : +12 V, +5 V, +3.3 V, Vcore Sistema - Microsoft® Windows® 8 / 8 de 64 bits / 7 / 7 de 64 bits / Vista Operacional

/ Vista

de 64 bits

Certicações - FCC, CE, WHQL

- “ErP/EuP Ready” (é necessária alimentação eléctrica “ErP/

EuP Ready”)

* Para informações mais detalhadas por favor visite o nosso sítio Web: http://www.asrock.com

ASRock FM2A85X Extreme4-M Motherboard

Page 99

1.3 Conguração dos Jumpers

A ilustração mostra como os jumpers são

congurados. Quando há uma capa de

jumpers sobre os pinos, diz–se que o jumper está “curto”. Não havendo capa sobre os pinos, o jumper está “aberto”. A ilustração mostra um jumper de 3 pinos em que os pinos 1 e 2 están “curtos” quando a capa de jumper estiver colocada sobre esses 2 pinos.

Jumper Conguração

Restaurar CMOS

(CLRCMOS1, jumper de 3 pinos) (veja a folha 2, No. 25)

Nota: CLRCMOS1 permite você limpar os dados em CMOS. Os dados em CMOS

incluem informações da conguração do sistema como: por exemplo a senha do sistema, data, tempo, e os parámetros da conguração do sistema. Para limpar e recongurar os parámetros do sistema a conguração inicial da fá-

brica, por favor desligue o cabo de força, ponha em curto–circuito os pin 2 e pin 3 de CLRCMOS1 por mais de 5 segundos para limpar o CMOS usando um jumper. Por favor lembrese de remover o jumper depois de limpar o COMS. Se precisar limpar o CMOS ao concluir a atualização do BIOS, deverá reiniciar o sistema primeiro e, em seguida, desligá-lo antes de executar a ação de limpeza o CMOS. Tenha em atenção que a palavra-passe, data, hora, perfil predefinido de utilizador, 1394 GUID e endereço MAC apenas serão limpos se a bateria do CMOS for retirada.

Conguração-padrão Limpar o CMOS

Se limpar o CMOS, poderá ser detectada a abertura da caixa. Ajuste aop-

ção do BIOS “Clear Status” (Limpar estado) para limpar o registo anterior de estado de intrusão no chassis.

ASRock FM2A85X Extreme4-M Motherboard

Português

Page 100

1.4 Conectores

Os conectores NÃO SÃO jumpers. NÃO coloque capas de jumper sobre estes conectores. A colocação de pontos de jumper sobre os

conectores causará danos irreversíveis à placa-mãe.

Conectores ATA3 Serial Estes sete conectores Serial

(SATA3_1:

veja a folha 2, No. 18)

(SATA3_2:

veja a folha 2, No. 19)

(SATA3_3:

veja a folha 2, No. 20)

(SATA3_4:

veja a folha 2, No. 17)

(SATA3_5: veja a folha 2, No. 16)

(SATA3_7: veja a folha 2, No. 15)

(SATA3_8: veja a folha 2, No. 18)

ATA (SATA3) suportam

unidades de disco rígido SATA

ou SATA3 como dispositivos de

SATA3_7 SATA3_5 SATA3_4

armazenamento internos. A

atual interface SATA3 permite

uma taxa de transferência de

dados de até 6.0 Gb/s.

SATA3_3 SATA3_2 SATA3_1

Cabo de dados Tanto a saída do cabo de Serial ATA (SATA) dados SATA pode ser

(opcional)

conectado ao disco rígido SATA3 quanto o conector SATA3 na placa mãe.

SATA3_8

Português

100

Porta de impressão Esta é a interface do cabo que

(LPT1 de 25 pinos)

(veja a folha 2, No. 29)

liga à porta de impressão e

impressoras.

AFD #

ERR OR#

PIN I T#

permite a fácil ligação de

SLI N #

SPD 2

SPD 1

SPD 0

STB #

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

SLC T

ASRock FM2A85X Extreme4-M Motherboard