Asrock Fatal1ty X370 Gaming K4 Quick Installation Guide

Version 1.1 Published January 2017 Copyright©2017 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Fatal1ty Story
Who knew that at age 19, I would be a World Champion PC gamer. When I was 13, I actually played competitive billiards in professional tournaments and won four or ve games o guys who played at the highest level. I actually thought of making a career of it, but at that young age situations change rapidly. Because I’ve been blessed with great hand-eye coordination and a grasp of mathematics (an important element in video gaming) I gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one of the top players in the United States, a company interested in sponsoring me ew me to Sweden to compete against the top 12 players in the world. I won 18 straight games, lost none, and took rst place, becoming the number one ranked Quake III player in the world in the process. Two months later I followed that success by traveling to Dallas and defending my title as the world’s best Quake III player, winning the $40,000 grand prize. From there I entered competitions all over the world, including Singapore, Korea, Germany, Australia, Holland and Brazil in addition to Los Angeles, New York and St. Louis.
WINNING STREAK
I was excited to showcase my true gaming skills when defending my title as CPL Champion of the year at the CPL Winter 2001 because I would be competing in a totally dierent rst person shooter (fps) game, Alien vs. Predator II. I won that competition and walked away with a new car. e next year I won the same title playing Unreal Tournament 2003, becoming the only three-time CPL champion of the year. And I did it playing a different game each year, something no one else has ever done and a feat of which I am extremely proud.
At QuakeCon 2002, I faced o against my rival ZeRo4 in one of the most highly anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon 2004, I became the World’s 1st Doom3 Champion by defeating Daler in a series of very challenging matches and earning $25,000 for the victory.
Since then Fatal1ty has traveled the globe to compete against the best in the world, winning prizes and acclaim, including the 2005 CPL World Tour Championship in New York City for a $150,000 rst place triumph. In August 2007, Johnathan was awarded the rst ever Lifetime Achievement Award in the four year history of the eSports-Award for “showing exceptional sportsmanship, taking part in shaping eSports into what it is today and for being the prime representative of this young sport. He has become the gurehead for eSports worldwide”.
LIVIN’ LARGE
Since my rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the world and livin’ large with lots of International media coverage on outlets such as MTV, ESPN and a 60 Minutes segment on CBS to name only a few. It's unreal - it's crazy. I’m living a dream by playing video games for a living. I’ve always been athletic and took sports like hockey and football very seriously, working out and training hard. is discipline helps me become a better gamer and my drive to be the best has opened the doors necessary to become a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made up of the best parts under my own brand. Quality hardware makes a huge difference in competitions…a couple more frames per second and everything gets really nice. It’s all about getting the computer processing faster and allowing more uid movement around the maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying about their equipment, something I’ve preached since I began competing. I don’t want to worry about my equipment. I want to be there – over and done with - so I can focus on the game. I want it to be the fastest and most stable computer equipment on the face of the planet, so quality is what Fatal1ty Brand products represent.
Johnathan “Fatal1ty” Wendel
e Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are registered trademarks of Fatal1ty, Inc., and are used under license. © 2014 Fatal1ty, Inc. All rights reserved. All other trademarks are the property of their respective owners.
Motherboard Layout
DDR4 _A2 (64 b it, 288 -pin mo dule)
DDR4 _A1 (64 b it, 288 -pin mo dule)
DDR4 _B2 (64 b it, 288 -pin mo dule)
DDR4 _B1 (64 b it, 288 -pin mo dule)
ATXP WR 1
PCIE2
Top:
Central/Bass
Center:
REAR SPK
Top:
LINE IN
Center:
FRONT
Bottom:
Optical
SPDIF
Bottom:
MIC IN
PCIE4
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_PLED1
COM1
1
1
HD_AUDIO1
X370 Gam in g K4
SATA3_3_4
SATA3_1_2
PCIE1
6
12
13
14
USB_1_2
1
21
19
USB_3_4
1
22
2526
SATA3_5_6
1
5
4
24
Dr.
Debug
15
CMOS
Battery
M2_1
M2_2
USB3_7_ 8
1
23
CPU_FAN1
7
8
9
10
11
1
TPMS1
Ult ra M.2
PCIe Ge n3 x4
FATAL TY
1
CHA_FAN1
3
2
USB3_9_ 10
1
AMD_FAN_LED1
1
CLRMOS1
1
LAN
AUDIO
CODEC
BIOS
ROM
RoHS
PCIE5
CHA_FAN2
16
1
USB_5
RGB_LED1
1
Super
I/O
PCIE6
PCIE3
CPU_OPT/W_PUMP
M2_3
NUT1
CHA_FAN3/W_PUMP
20
Top: RJ-45
USB 3.0 T: USB5 B: USB6
USB 3.1 T: USB3_TA_1 B: USB3_TC_1
PS2
Keybo ard
PS2
Mouse
USB 3.0 T: USB1 B: USB2
USB 3.0 T: USB3 B: USB4
18
17
RGB_LED2
1
AMD
Promontory
X370
SOCKETAM4
HDMI1
Fatal1ty X370 Gaming K4 Series
English
1
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 CPU Fan Connector (CPU_FAN1)
3 CPU Fan / Waterpump Fan Connector (CPU_OPT/W_PUMP)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
6 ATX Power Connector (ATXPWR1)
7 USB 3.0 Header (USB3_9_10)
8 USB 3.0 Header (USB3_7_8)
9 AMD LED Fan USB Header (USB_5)
10 AMD Fan LED Header (AMD_FAN_LED1)
11 Chassis Fan Connector (CHA_FAN1)
12 SATA3 Connectors (SATA3_5_6)
13 SATA3 Connectors (SATA3_3_4)
14 SATA3 Connectors (SATA3_1_2)
15 System Panel Header (PANEL1)
16 RGB LED Header (RGB_LED1)
17 RGB LED Header (RGB_LED2)
18 Clear CMOS Jumper (CLRMOS1)
19 Chassis Fan / Waterpump Fan Connector (CHA_FAN3/W_PUMP)
20 Chassis Fan Connector (CHA_FAN2)
21 USB 2.0 Header (USB_1_2)
22 USB 2.0 Header (USB_3_4)
23 Power LED and Speaker Header (SPK_PLED1)
24 TPM Header (TPMS1)
25 COM Port Header (COM1)
26 Front Panel Audio Header (HD_AUDIO1)
English
2
I/O Panel
Fatal1ty X370 Gaming K4 Series
5
1
2
436
16 1517
No. Description No. Description
1 PS/2 Mouse Port 10 USB 3.1 Type-A Port (USB3_TA_1)
2 LAN RJ-45 Port* 11 USB 3.1 Type-C Port (USB3_TC_1)
3 Central / Bass (Orange) 12 USB 3.0 Ports (USB3_3_4)
4 Rear Speaker (Black) 13 Fatal1ty Mouse Port (USB3_1)
5 Line In (Light Blue) 14 USB 3.0 Port (USB3_2)
6 Front Speaker (Lime)** 15 HDMI Port (HDMI1)
7 Microphone (Pink) 16 PS/2 Keyboard Port
8 Optical SPDIF Out Port 17 Antenna Ports
9 USB 3.0 Ports (USB3_5_6)
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
13 12
1114
9
7810
Activity / Link LED Speed LED
Status Description Status Description
O No Link Orange 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection
English
3
** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below for connection d etails in accordance w ith the type of speaker you use.
Audio Output
Channels
Front Speaker
(No. 6)
Rear Speaker
(No. 4)
Central / Bass
(No. 3)
2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V
To enable Multi-Streaming, you need to connect a front panel audio cable to the front panel audio header. Aer restarting your computer, you will nd the “Mixer” tool on your system. Please select “Mixe r ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to u se the Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use the front panel audio.
Line In (No. 5)
English
4
Fatal1ty X370 Gaming K4 Series
Chapter 1 Introduction
ank you for purchasing ASRock Fatal1ty X370 Gaming K4 Series motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be available on ASRock’s website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.
1.1 Package Contents
ASRock Fatal1ty X370 Gaming K4 Series Motherboard (ATX Form Factor)
•
ASRock Fatal1ty X370 Gaming K4 Series Quick Installation Guide
•
ASRock Fatal1ty X370 Gaming K4 Series Support CD
•
1 x I/O Panel Shield
•
4 x Serial ATA (SATA) Data Cables (Optional)
•
1 x ASRock SLI_HB_Bridge_2S Card (Optional)
•
3 x Screws for M.2 Socket (Optional)
•
English
5
1.2 Specications
Platform
CPU
Chipset
Memory
* Please refer to Memory Support List on ASRock’s website for more information. (http://www.asrock.com/) * Please refer to page 23 for DDR4 UDIMM maximum frequency support.
ATX Form Factor
•
Supports AMD Socket AM4 A-Series APUs (Bristol Ridge)
•
and Ryzen CPUs (Summit Ridge) IR Digital PWM
•
12 Power Phase design
•
Supports 95W Water Cooling
•
AMD Promontory X370
•
Dual Channel DDR4 Memory Technology
•
4 x DDR4 DIMM Slots
•
AMD Ryzen series CPUs support DDR4 2933+(OC)/
•
2667/2400/2133 ECC & non-ECC, un-buered memory* AMD 7th Gen A-Series APUs support DDR4 2400/2133 ECC
•
& non-ECC, un-buered memory*
Max. capacity of system memory: 64GB
•
15μ Gold Contact in DIMM Slots
•
English
6
Expansion Slot
AMD Ryzen series CPUs
2 x PCI Express 3.0 x16 Slots (single at x16 (PCIE2); dual at
•
x8 (PCIE2) / x8 (PCIE4))*
AMD 7th A-Series APUs
1 x PCI Express 3.0 x16 Slot (single at x8 (PCIE2))*
•
* Supports NVMe SSD as boot disks
4 x PCI Express 2.0 x1 Slots
•
Supports AMD Quad CrossFireXTM and CrossFireXTM
•
Supports NVIDIA® Quad SLITM and SLI
•
1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
•
15μ Gold Contact in VGA PCIe Slot (PCIE2)
•
TM
Graphics
Audio
Fatal1ty X370 Gaming K4 Series
Integrated AMD RadeonTM R7/R5 Series Graphics in A-series
•
APU DirectX 12, Pixel Shader 5.0
•
Max. shared memory 1GB
•
Supports HDMI with max. resolution up to 4K x 2K
•
(4096x2160) @ 24Hz / (3840x2160) @ 30Hz Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI Port (Compliant HDMI monitor is required) Supports HDCP with HDMI Port
•
Supports Full HD 1080p Blu-ray (BD) playback with HDMI
•
Port
7.1 CH HD Audio with Content Protection (Realtek
•
ALC1220 Audio Codec) Premium Blu-ray Audio support
•
Supports Surge Protection
•
Nichicon Fine Gold Series Audio Caps
•
120dB SNR DAC with Dierential Amplier
•
TI® NE5532 Premium Headset Amplier for Front Panel
•
Audio Connector (Supports up to 600 Ohm headsets) Pure Power-In
•
Direct Drive Technology
•
PCB Isolate Shielding
•
Impedance Sensing on Line Out port
•
Individual PCB Layers for R/L Audio Channel
•
Gold Audio Jacks
•
Supports Creative SoundBlaster Cinema3
•
LAN
Rear Panel I/O
Gigabit LAN 10/100/1000 Mb/s
•
GigaLAN Intel® I211AT
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
2 x Antenna Ports
•
1 x PS/2 Mouse Port
•
1 x PS/2 Keyboard Port
•
English
7
English
Storage
Connector
1 x HDMI Port
•
1 x Optical SPDIF Out Port
•
1 x USB 3.1 Type-A Port (10 Gb/s) (Supports ESD Protection)
•
1 x USB 3.1 Type-C Port (10 Gb/s) (Supports ESD Protection)
•
6 x USB 3.0 Ports (Supports ESD Protection)
•
* 1 x Fatal1ty Mouse Port (USB 3.0) is included
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED) HD Audio Jacks: Rear Speaker / Central / Bass / Line in /
•
Front Speaker / Microphone (Gold Audio Jacks)
6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1 and RAID 10), NCQ, AHCI and Hot Plug 1 x Ultra M.2 Socket (M2_1), supports type
•
2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s) (with Ryzen CPU) or Gen3 x2 (16 Gb/s) (with A-Series APU)* 1 x M.2 Socket (M2_2), supports type 2230/2242/2260/2280
•
M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module
up to Gen2 x2 (10 Gb/s)* * Supports NVMe SSD as boot disks * Supports ASRock U.2 Kit
1 x COM Port Header
•
1 x TPM Header
•
1 x Power LED and Speaker Header
•
1 x AMD Fan LED Header
•
2 x RGB LED Headers
•
* Supports up to 12V/3A, 36W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.
1 x CPU Optional/Water Pump Fan Connector (4-pin)
•
(Smart Fan Speed Control) * e CPU Optional/Water Pump Fan supports the water cooler fan of maximum 1.5A (18W) fan power.
2 x Chassis Fan Connectors (4-pin) (Smart Fan Speed Con-
•
trol)
8
BIOS Feature
Fatal1ty X370 Gaming K4 Series
1 x Chassis Optional/Water Pump Fan Connector (4-pin)
•
(Smart Fan Speed Control) * e Chassis Optional/Water Pump Fan supports the water cooler fan of maximum 1.5A (18W) fan power. * CHA_FAN2 can auto detect if 3-pin or 4-pin fan is in use.
1 x 24 pin ATX Power Connector (Hi-Density Power
•
Connec tor)
1 x 8 pin 12V Power Connector (Hi-Density Power
•
Connec tor)
1 x Front Panel Audio Connector
•
1 x AMD LED Fan USB Header
•
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
•
ESD Protection)
2 x USB 3.0 Headers (Support 4 USB 3.0 ports) (Supports
•
ESD Protection)
1 x Dr. Debug with LED
•
AMI UEFI Legal BIOS with multilingual GUI support
•
Supports “Plug and Play”
•
ACPI 5.1 compliance wake up events
•
Supports jumperfree
•
SMBIOS 2.3 support
•
CPU, VCORE_NB, DRAM, VPPM, PCH 1.05V, +1.8V,
•
VDDP, PROM 2.5V, Voltage Multi-adjustment
Hardware Monitor
Temperature Sensing: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans
Fan Tachometer: CPU, CPU Optional/Water Pump, Chassis,
•
Chassis Optional/Water Pump Fans
Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, CPU Optional/Water Pump, Chassis, Chassis
Optional/Water Pump Fans
Fan Multi-Speed Control: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, VCORE_
•
NB, DRAM, PCH 1.05V, +1.8V, VDDP
English
9
Microso® Windows® 10 64-bit
OS
•
* For the updated Windows® 10 driver, please visit ASRock ’s website for details: http://www.asrock.com
FCC, CE, WHQL
Certica­tions
* For detailed product information, please visit our website: http://www.asrock .com
Please realize that the re is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. O verclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your ow n risk and expense. We are not responsible for possible damage caused by overclocking.
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
English
10
Fatal1ty X370 Gaming K4 Series
Chapter 2 Installation
is is a ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard.
•
Failure to do so may cause physical injuries to you and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
11
English
2.1 Installing the CPU
Unplug all power cables be fore installing the CPU.
1
English
12
2
Fatal1ty X370 Gaming K4 Series
3
13
English
2.2 Installing the CPU Fan and Heatsink
Aer you install the CPU into this motherboard, it is necessary to install a larger heatsink and cooling fan to dissipate heat. You also need to spray thermal grease between the CPU and the heatsink to improve heat dissipation. Make sure that the CPU and the heatsink are securely fastened and in good contact with each other.
Please turn o the power or remove the power cord before changing a CPU or heatsink.
Installing the CPU Box Cooler SR1
1
English
14
2
Fatal1ty X370 Gaming K4 Series
3
4
1
N
FA
_
U
P
C
English
15
Installing the AM4 Box Cooler SR2
1
2
English
16
Fatal1ty X370 Gaming K4 Series
3
17
English
4
1
N
FA
_
U
P
C
5
4-pin FAN cable
English
18
RGB LED Cable
1
N
FA
CPU_
1
D
E
L
_
N
FA
_
D
AM
+12V
*e diagram shown here are for reference only. Please refer to page 31 for the orientation of AMD Fan LED Header (AMD_FAN_LED1).
Installing the AM4 Box Cooler SR3
1
Fatal1ty X370 Gaming K4 Series
2
English
19
3
4
English
20
Fatal1ty X370 Gaming K4 Series
5
FAN1
CPU_
21
English
6
1
N
FA
_
U
P
C
1
D
E
L
_
N
FA
_
D
AM
+12V
or
7
1
N
FA
_
U
P
C
1
D
E
L
_
N
FA
_
D
AM
5
_
B
S
U
English
Please note that only one cable should be used at a time in this step. If you select AMD_FAN_LED1, please install ASRock utility "ASRock RGB LED". If you select USB connector, please install AMD utility "SR3 Settings Soware".
*e diagram shown here are for reference only. Please refer to page 31 for the orientation of AMD Fan LED Header (AMD_FAN_LED1) and page 28 for the orientation of AMD LED Fan USB Header (USB_5).
22
Fatal1ty X370 Gaming K4 Series
2.3 Installing Memory Modules (DIMM)
is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
1. For dual channel conguration , you always need to in stall identical (the same brand, speed , size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Du al Channel Memory Technology with only one or three memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
DDR4 UDIMM Maximum Frequency Support
A-Series APUs:
UDIMM Memory Slot
A1 A2 B1 B2
- SR - - 2400
- DR - - 2400
- SR - SR 2400
- DR - DR 2133
SR SR SR SR 1866
SR/DR DR SR/DR DR 1866
Frequency
(Mhz)
Ryzen CPUs:
UDIMM Memory Slot
A1 A2 B1 B2
- SR - - 2667
- DR - - 2667
- SR - SR 2667
- DR - DR 2400-2667
SR SR SR SR 2133-2400
SR/DR DR SR/DR DR 1866-2133
SR: Single rank DIMM, 1Rx4 or 1Rx8 on DIMM module label
DR: Dual rank DIMM, 2Rx4 or 2R x8 on DIMM module label
Frequency
(Mhz)
English
23
e DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incor rect orientation.
1
2
English
24
3
Fatal1ty X370 Gaming K4 Series
2.4 Expansion Slots (PCI Express Slots)
ere are 6 PCI Express slots on the motherboard.
Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Please re ad the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.
PCIe slots:
PCIE1 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE3 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x8 lane width graphics cards. PCIE5 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE6 (PCIe 2.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIe Slot Congurations
th
7
A-Series APUs :
PCIE2 PCIE4
Single Graphics Card x8 N/A
Ryzen series CPUs:
PCIE2 PCIE4
Single Graphics Card x16 N/A
Two Graphics Cards in
CrossFireXTM or SLITM
Mode
For a better thermal environment, please connect a chassis fan to the motherboard’s chassis fan connector (CHA_FAN1 or CH A_FAN2) when using multiple graphics card s.
x8 x8
English
25
2.5 Jumpers Setup
e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”
when a jumper cap is placed on these 2 pins.
Clear CMOS Jumper (CLRMO S1) (see p.1, No. 18)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed.
Clear CMOSDefault
English
26
Loading...
+ 146 hidden pages