Version 1.0
Published January 2017
Copyright©2017 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to
infringe.
Disclaimer:
Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.
In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see ww w.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Fatal1ty Story
Who knew that at age 19, I would be a World Champion PC gamer. When I was 13, I actually
played competitive billiards in professional tournaments and won four or ve games o guys
who played at the highest level. I actually thought of making a career of it, but at that young
age situations change rapidly. Because I’ve been blessed with great hand-eye coordination and
a grasp of mathematics (an important element in video gaming) I gravitated to that activity.
GOING PRO
I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional
League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one
of the top players in the United States, a company interested in sponsoring me ew me to
Sweden to compete against the top 12 players in the world. I won 18 straight games, lost
none, and took rst place, becoming the number one ranked Quake III player in the world
in the process. Two months later I followed that success by traveling to Dallas and defending
my title as the world’s best Quake III player, winning the $40,000 grand prize. From there
I entered competitions all over the world, including Singapore, Korea, Germany, Australia,
Holland and Brazil in addition to Los Angeles, New York and St. Louis.
WINNING STREAK
I was excited to showcase my true gaming skills when defending my title as CPL
Champion of the year at the CPL Winter 2001 because I would be competing in a totally
dierent rst person shooter (fps) game, Alien vs. Predator II. I won that competition and
walked away with a new car. e next year I won the same title playing Unreal Tournament
2003, becoming the only three-time CPL champion of the year. And I did it playing a
different game each year, something no one else has ever done and a feat of which I am
extremely proud.
At QuakeCon 2002, I faced o against my rival ZeRo4 in one of the most highly
anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon
2004, I became the World’s 1st Doom3 Champion by defeating Daler in a series of very
challenging matches and earning $25,000 for the victory.
Since then Fatal1ty has traveled the globe to compete against the best in the world, winning
prizes and acclaim, including the 2005 CPL World Tour Championship in New York City for
a $150,000 rst place triumph. In August 2007, Johnathan was awarded the rst ever Lifetime
Achievement Award in the four year history of the eSports-Award for “showing exceptional
sportsmanship, taking part in shaping eSports into what it is today and for being the prime
representative of this young sport. He has become the gurehead for eSports worldwide”.
LIVIN’ LARGE
Since my rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the
world and livin’ large with lots of International media coverage on outlets such as MTV,
ESPN and a 60 Minutes segment on CBS to name only a few. It's unreal - it's crazy. I’m living
a dream by playing video games for a living. I’ve always been athletic and took sports like
hockey and football very seriously, working out and training hard. is discipline helps me
become a better gamer and my drive to be the best has opened the doors necessary to become
a professional.
A DREAM
Now, another dream is being realized – building the ultimate gaming computer, made
up of the best parts under my own brand. Quality hardware makes a huge difference in
competitions…a couple more frames per second and everything gets really nice. It’s all about
getting the computer processing faster and allowing more uid movement around the maps.
My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying
about their equipment, something I’ve preached since I began competing. I don’t want to
worry about my equipment. I want to be there – over and done with - so I can focus on
the game. I want it to be the fastest and most stable computer equipment on the face of the
planet, so quality is what Fatal1ty Brand products represent.
Johnathan “Fatal1ty” Wendel
e Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are registered trademarks of Fatal1ty, Inc., and are used
under license. © 2015 Fatal1ty, Inc. All rights reserved. All other trademarks are the property of their respective
owners.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specications 2
1.3 Motherboard Layout 7
1.4 I/O Panel 9
Chapter 2 Installation 11
2.1 Installing the CPU 12
2.2 Installing the CPU Fan and Heatsink 14
2.3 Installing Memory Modules (DIMM) 23
2.4 Expansion Slots (PCI Express Slots) 25
2.5 Jumpers Setup 26
2.6 Onboard Headers and Connectors 27
2.7 Dr. Debug 32
2.8 SLITM and Quad SLITM Operation Guide 34
2.8.1 Installing Two SLITM-Ready Graphics Cards 34
2.8.2 Driver Installation and Setup 36
2.9 CrossFireXTM and Quad CrossFireXTM Operation Guide 37
2.9.1 Installing Two CrossFireXTM-Ready Graphics Cards 37
2.9.2 Driver Installation and Setup 39
2.10 M.2_SSD (NGFF) Module Installation Guide 40
Chapter 3 Software and Utilities Operation 44
3.1 Installing Drivers 44
3.2 F-Stream 45
3.2.1 Installing F-Stream 45
3.2.2 Using F-Stream 45
3.3 ASRock Live Update & APP Shop 48
3.3.1 UI Overview 48
3.3.2 Apps 49
3.3.3 BIOS & Drivers 52
3.3.4 Setting 53
3.4 Creative SoundBlaster Cinema3 54
3.5 ASRock RGB LED 55
Chapter 4 UEFI SETUP UTILITY 57
4.1 Introduction 57
4.1.1 UEFI Menu Bar 57
4.1.2 Navigation Keys 58
4.2 Main Screen 59
4.3 OC Tweaker Screen 60
4.4 Advanced Screen 62
4.4.1 CPU Conguration 63
4.4.2 North Bridge Conguration 64
4.4.3 South Bridge Conguration 65
4.4.4 Storage Conguration 66
4.4.5 Super IO Conguration 67
4.4.6 ACPI Conguration 68
4.4.7 Trusted Computing 69
4.5 Tools 70
4.6 Hardware Health Event Monitoring Screen 72
4.7 Security Screen 74
4.8 Boot Screen 75
4.9 Exit Screen 77
Fatal1ty X370 Gaming K4 Series
Chapter 1 Introduction
ank you for purchasing ASRock Fatal1ty X370 Gaming K4 Series motherboard,
a reliable motherboard produced under ASRock’s consistently stringent quality
control. It delivers excellent performance with robust design conforming to
ASRock’s commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the
motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the soware and utilities. Chapter 4 contains the conguration guide of
the BIOS setup.
Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s
website w ithout further notice. If you require technical support related to this motherboard, please visit our website for specic information about the model you are using. You
may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock
website http://www.asrock.com.
1.1 Package Contents
ASRock Fatal1ty X370 Gaming K4 Series Motherboard (ATX Form Factor)
•
ASRock Fatal1ty X370 Gaming K4 Series Quick Installation Guide
•
ASRock Fatal1ty X370 Gaming K4 Series Support CD
•
1 x I/O Panel Shield
•
4 x Serial ATA (SATA) Data Cables (Optional)
•
1 x ASRock SLI_HB_Bridge_2S Card (Optional)
•
3 x Screws for M.2 Socket (Optional)
•
English
1
1.2 Specications
Platform
CPU
Chipset
Memory
•
•
•
•
•
•
•
•
•
•
* Please refer to Memory Support List on ASRock’s website for
more information. (http://www.asrock.com/)
* Please refer to page 23 for DDR4 UDIMM maximum
frequency support.
•
•
ATX Form Factor
Supports AMD Socket AM4 A-Series APUs (Bristol Ridge)
and Ryzen CPUs (Summit Ridge)
IR Digital PWM
12 Power Phase design
Supports 95W Water Cooling
AMD Promontory X370
Dual Channel DDR4 Memory Technology
4 x DDR4 DIMM Slots
AMD Ryzen series CPUs support DDR4 2933+(OC)/
2667/2400/2133 ECC & non-ECC, un-buered memory*
AMD 7th Gen A-Series APUs support DDR4 2400/2133 ECC
& non-ECC, un-buered memory*
Max. capacity of system memory: 64GB
15μ Gold Contact in DIMM Slots
English
2
Expansion
Slot
AMD Ryzen series CPUs
2 x PCI Express 3.0 x16 Slots (single at x16 (PCIE2); dual at
•
x8 (PCIE2) / x8 (PCIE4))*
AMD 7th A-Series APUs
1 x PCI Express 3.0 x16 Slot (single at x8 (PCIE2))*
•
* Supports NVMe SSD as boot disks
4 x PCI Express 2.0 x1 Slots
•
Supports AMD Quad CrossFireX
•
Supports NVIDIA® Quad SLITM and SLI
•
1 x M.2 Socket (Key E), supports ty pe 2230 WiFi/BT module
•
15μ Gold Contact in VGA PCIe Slot (PCIE2)
•
TM
and CrossFireXTM
TM
Graphics
Audio
Fatal1ty X370 Gaming K4 Series
Integrated AMD RadeonTM R7/R5 Series Graphics in A-series
•
APU
DirectX 12, Pixel Shader 5.0
•
Max. shared memory 1GB
•
Supports HDMI with max. resolution up to 4K x 2K
•
(4096x2160) @ 24Hz / (3840x2160) @ 30Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
•
HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
Supports HDCP with HDMI Port
•
Supports Full HD 1080p Blu-ray (BD) playback with HDMI
•
Port
7.1 CH HD Audio with Content Protection (Realtek
•
ALC1220 Audio Codec)
Premium Blu-ray Audio support
•
Supports Surge Protection
•
Nichicon Fine Gold Series Audio Caps
•
120dB SNR DAC with Dierential Amplier
•
TI® NE5532 Premium Headset Amplier for Front Panel
•
Audio Connector (Supports up to 600 Ohm headsets)
Pure Power-In
•
Direct Drive Technology
•
PCB Isolate Shielding
•
Impedance Sensing on Line Out port
•
Individual PCB Layers for R/L Audio Channel
•
Gold Audio Jacks
•
Supports Creative SoundBlaster Cinema3
•
LAN
Rear Panel
I/O
Gigabit LAN 10/100/10 00 Mb/s
•
GigaLAN Intel® I211AT
•
Supports Wake-On-LAN
•
Supports Lightning/ESD Protection
•
Supports Energy Ecient Ethernet 802.3az
•
Supports PXE
•
2 x Antenna Ports
•
1 x PS/2 Mouse Port
•
English
3
Storage
1 x PS/2 Keyboard Port
•
1 x HDMI Port
•
1 x Optical SPDIF Out Port
•
1 x USB 3.1 Ty pe-A Port (10 Gb/s) (Supports ESD Protection)
•
1 x USB 3.1 Ty pe-C Port (10 Gb/s) (Supports ESD Protection)
•
6 x USB 3.0 Ports (Supports ESD Protection)
•
* 1 x Fatal1ty Mouse Port (USB 3.0) is included
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
•
LED)
HD Audio Jacks: Rear Speaker / Centra l / Bass / Line in /
•
Front Speaker / Microphone (Gold Audio Jacks)
6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
•
RAID 1 and RAID 10), NCQ, AHCI and Hot Plug
1 x Ultra M.2 Socket (M2_1), supports ty pe
•
2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2
PCI Express module up to Gen3 x4 (32 Gb/s) (with Ryzen
CPU) or Gen3 x2 (16 Gb/s) (with A-Series APU)*
1 x M.2 Socket (M2_2), supports type 2230/2242/2260/2280
•
M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module
up to Gen2 x2 (10 Gb/s)*
* Supports NVMe SSD as boot disks
* Supports ASRock U.2 Kit
English
4
Connector
1 x COM Port Header
•
1 x TPM Header
•
1 x Power LED and Speaker Header
•
1 x AMD Fan LED Header
•
2 x RGB LED Headers
•
* Supports up to 12V/3A, 36W LED Strip
1 x CPU Fan Connector (4-pin)
•
* e CPU Fan Connector supports the CPU fan of ma ximum
1A (12W) fan power.
1 x CPU Optional/Water Pump Fan Connector (4-pin)
•
(Smart Fan Speed Control)
* e CPU Optional/Water Pump Fan supports the water cooler
fan of maximum 1.5A (18W) fan power.
2 x Chassis Fan Connectors (4-pin) (Smart Fan Speed Con-
•
trol)
BIOS
Feature
Fatal1ty X370 Gaming K4 Series
1 x Chassis Optional/Water Pump Fan Connector (4-pin)
•
(Smart Fan Speed Control)
* e Chassis Optiona l/Water Pump Fan supports the water
cooler fan of maximum 1.5A (18W) fan power.
* CHA_FAN2 can auto detect if 3-pin or 4-pin fan is in use.
1 x 24 pin ATX Power Connector (Hi-Density Power
•
Connec tor)
1 x 8 pin 12V Power Connector (Hi-Density Power
•
Connec tor)
1 x Front Panel Audio Connector
•
1 x AMD LED Fan USB Header
•
2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
•
ESD Protection)
2 x USB 3.0 Headers (Support 4 USB 3.0 ports) (Supports
•
ESD Protection)
1 x Dr. Debug with LED
•
AMI UEFI Legal BIOS with multilingual GUI support
•
Supports “Plug and Play”
•
ACPI 5.1 compliance wake up events
•
Supports jumperfree
•
SMBIOS 2.3 support
•
CPU, VCORE_NB, DRAM, VPPM, PCH 1.05V, +1.8V,
•
VDDP, PROM 2.5V, Voltage Multi-adjustment
Hardware
Monitor
Temperature Sensing: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans
Fan Tachometer: CPU, CPU Optional/Water Pump, Chassis,
•
Chassis Optional/Water Pump Fans
Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
•
ture): CPU, CPU Optional/Water Pump, Chassis, Chassis
Optional/Water Pump Fans
Fan Multi-Speed Control: CPU, CPU Optional/Water Pump,
•
Chassis, Chassis Optional/Water Pump Fans
Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, VCORE_
•
NB, DRAM, PCH 1.05V, +1.8V, VDDP
English
5
Microso® Windows® 10 64-bit
OS
•
* For the updated Windows® 10 driver, please visit ASRock ’s
website for details: http://ww w.asrock.com
FCC, CE, WHQL
Certications
* For detailed product information, please visit our website: http://www.asrock .com
Please realiz e that the re is a certain r isk involved with o verclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party
overclocking to ols. O verclocking may aect your system’s stability, or even c ause damage to
the components and devices of your system. It should be don e at your ow n risk and expense.
We are not responsibl e for possible damage caused by overclo cking.
•
ErP/EuP ready (ErP/EuP ready power supply is required)
•
English
6
DDR4 _A2 (64 b it, 288 -pin mo dule)
DDR4 _A1 (64 b it, 288 -pin mo dule)
DDR4 _B2 (64 b it, 288 -pin mo dule)
DDR4 _B1 (64 b it, 288 -pin mo dule)
ATXP WR 1
PCIE2
Top:
Central/Bass
Center:
REAR SPK
Top:
LINE IN
Center:
FRONT
Bottom:
Optical
SPDIF
Bottom:
MIC IN
PCIE4
HDLED RESET
PLED PWRBTN
PANEL1
1
1
SPK_PLED1
COM1
1
1
HD_AUDIO1
X370 Gam in g K4
SATA3_3_4
SATA3_1_2
PCIE1
6
12
13
14
USB_1_2
1
21
19
USB_3_4
1
22
2526
SATA3_5_6
1
5
4
24
Dr.
Debug
15
CMOS
Battery
M2_1
M2_2
USB3_7_ 8
1
23
CPU_FAN1
7
8
9
10
11
1
TPMS1
Ult ra M.2
PCIe Ge n3 x4
FATAL TY
1
CHA_FAN1
3
2
USB3_9_ 10
1
AMD_FAN_LED1
1
CLRMOS1
1
LAN
AUDIO
CODEC
BIOS
ROM
RoHS
PCIE5
CHA_FAN2
16
1
USB_5
RGB_LED1
1
Super
I/O
PCIE6
PCIE3
CPU_OPT/W_PUMP
M2_3
NUT1
CHA_FAN3/W_PUMP
20
Top:
RJ-45
USB 3.0
T: USB5
B: USB6
USB 3.1
T: USB3_TA_1
B: USB3_TC_1
PS2
Keybo ard
PS2
Mouse
USB 3.0
T: USB1
B: USB2
USB 3.0
T: USB3
B: USB4
18
17
RGB_LED2
1
AMD
Promontory
X370
SOCKETAM4
HDMI1
1.3 Motherboard Layout
Fatal1ty X370 Gaming K4 Series
English
7
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 CPU Fan Connector (CPU_FAN1)
3 CPU Fan / Waterpump Fan Connector (CPU_OPT/W_PUMP)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
6 ATX Power Connector (ATXPWR1)
7 USB 3.0 Header (USB3_9_10)
8 USB 3.0 Header (USB3_7_8)
9 AMD LED Fan USB Header (USB_5)
10 AMD Fan LED Header (AMD_FAN_LED1)
11 Chassis Fan Connector (CHA_FAN1)
12 SATA3 Connectors (SATA3_5_6)
13 SATA3 Connec tors (SATA3_ 3_4)
14 SATA3 Connectors (SATA3_1_2)
15 System Panel Header (PANEL1)
16 RGB LED Header (RGB_LED1)
17 RGB LED Header (RGB_LED2)
18 Clear CMOS Jumper (CLRMOS1)
19 Chassis Fan / Waterpump Fan Connector (CHA_FAN3/W_PUMP)
20 Chassis Fan Connector (CHA_FAN2)
21 USB 2.0 Header (USB_1_2)
22 USB 2.0 Header (USB_3_4)
23 Power LED and Speaker Header (SPK_PLED1)
24 TPM Header (TPMS1)
25 COM Port Header (COM1)
26 Front Panel Audio Header (HD_AUDIO1)
English
8
1.4 I/O Panel
1
Fatal1ty X370 Gaming K4 Series
5
2
436
16 1517
No. Description No. Description
1 PS/2 Mouse Port 10 USB 3.1 Type-A Port (USB3_TA_1)
2 LAN RJ-45 Port* 11 USB 3.1 Type-C Port (USB3_TC_1)
3 Central / Bass (Orange) 12 USB 3.0 Ports (USB3_3_4)
4 Rear Speaker (Black) 13 Fatal1ty Mouse Port (USB3_1)
5 Line In (Light Blue) 14 USB 3.0 Port (USB3_2)
6 Front Speaker (Lime)** 15 HDMI Port (HDMI1)
7 Microphone (Pink) 16 PS/2 Keyboard Port
8 Optical SPDIF Out Port 17 Antenna Ports
9 USB 3.0 Ports (USB3_5_6)
* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Por t
13 12
1114
9
7810
Activity / Link LED Speed LED
Status Description Status Description
O No Link Orange 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
English
9
** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table be low
for connection d etails in accordance w ith the type of speaker you use.
Audio Output
Channels
2 V -- -- --
4 V V -- --
6 V V V --
8 V V V V
Front Speaker
(No. 6)
Rear Speaker
(No. 4)
Central / Bass
(No. 3)
Line In
(No. 5)
English
10
Fatal1ty X370 Gaming K4 Series
Chapter 2 Installation
is is a ATX form factor motherboard. Before you install the motherboard, study
the conguration of your chassis to ensure that the motherboard ts into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
Make sure to unplug the power cord before installing or removing the motherboard.
•
Failure to do so may cause physical injuries to you and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,
•
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.
•
Whenever you uninstall any components, place them on a grounded anti-static pad or
•
in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-
•
tighten the screws! Doing so may damage the motherboard.
11
English
2.1 Installing the CPU
Unplug all power cables be fore installing the CPU.
1
English
12
2
Fatal1ty X370 Gaming K4 Series
3
13
English
2.2 Installing the CPU Fan and Heatsink
Aer you install the CPU into this motherboard, it is necessary to install a larger
heatsink and cooling fan to dissipate heat. You also need to spray thermal grease
between the CPU and the heatsink to improve heat dissipation. Ma ke sure that the
CPU and the heatsink are securely fastened and in good contact with each other.
Please turn o the power or remove th e power cord before changing a CPU or heatsink.
Installing the CPU Box Cooler SR1
1
English
14
2
Fatal1ty X370 Gaming K4 Series
3
4
1
N
FA
_
U
P
C
English
15
Installing the AM4 Box Cooler SR2
1
2
English
16
Fatal1ty X370 Gaming K4 Series
3
17
English
4
1
N
FA
_
U
P
C
5
4-pin FAN cable
English
18
RGB LED Cable
1
FAN
CPU_
1
D
LE
_
N
FA
_
D
AM
+12V
*e diagram shown here are for reference only. Please refer to page 31 for the orientation of
AMD Fan LED Header (AMD_FAN_LED1).
Loading...