Asrock Fatal1ty E3V5 Performance Gaming/OC Quick Installation Guide

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2-28965588 ext.123 (Standard International call charges apply)

Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535; 7,003,467 & other U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together is a registered trademark & DTS Connect, DTS Interactive, DTS Neo:PC are trademarks of DTS, Inc. Product includes soware. © DTS, Inc., All Rights Reserved.

Fatal1ty Story

Who knew that at age 19, I would be a World Champion PC gamer. When I was 13, I actually played competitive billiards in professional tournaments and won four or ve games o guys who played at the highest level. I actually thought of making a career of it, but at that young age situations change rapidly. Because I’ve been blessed with great hand-eye coordination and a grasp of mathematics (an important element in video gaming) I gravitated to that activity.

GOING PRO

I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one of the top players in the United States, a company interested in sponsoring me ew me to Sweden to compete against the top 12 players in the world. I won 18 straight games, lost none, and took rst place, becoming the number one ranked Quake III player in the world in the process. Two months later I followed that success by traveling to Dallas and defending my title as the world’s best Quake III player, winning the $40,000 grand prize. From there I entered competitions all over the world, including Singapore, Korea, Germany, Australia, Holland and Brazil in addition to Los Angeles, New York and St. Louis.

WINNING STREAK

I was excited to showcase my true gaming skills when defending my title as CPL Champion of the year at the CPL Winter 2001 because I would be competing in a totally dierent rst person shooter (fps) game, Alien vs. Predator II. I won that competition and walked away with a new car. e next year I won the same title playing Unreal Tournament 2003, becoming the only three-time CPL champion of the year. And I did it playing a different game each year, something no one else has ever done and a feat of which I am extremely proud.

At QuakeCon 2002, I faced o against my rival ZeRo4 in one of the most highly anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon 2004, I became the World’s 1st Doom3 Champion by defeating Daler in a series of very challenging matches and earning $25,000 for the victory.

Since then Fatal1ty has traveled the globe to compete against the best in the world, winning prizes and acclaim, including the 2005 CPL World Tour Championship in New York City for a $150,000 rst place triumph. In August 2007, Johnathan was awarded the rst ever Lifetime Achievement Award in the four year history of the eSports-Award for “showing exceptional sportsmanship, taking part in shaping eSports into what it is today and for being the prime representative of this young sport. He has become the gurehead for eSports worldwide”.

LIVIN’ LARGE

Since my rst big tournament wins, I have been a “Professional Cyberathlete”, traveling the world and livin’ large with lots of International media coverage on outlets such as MTV, ESPN and a 60 Minutes segment on CBS to name only a few. It's unreal - it's crazy. I’m living a dream by playing video games for a living. I’ve always been athletic and took sports like hockey and football very seriously, working out and training hard. is discipline helps me become a better gamer and my drive to be the best has opened the doors necessary to become a professional.

A DREAM

Now, another dream is being realized – building the ultimate gaming computer, made up of the best parts under my own brand. Quality hardware makes a huge difference in competitions…a couple more frames per second and everything gets really nice. It’s all about getting the computer processing faster and allowing more uid movement around the maps.

My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying about their equipment, something I’ve preached since I began competing. I don’t want to worry about my equipment. I want to be there – over and done with - so I can focus on the game. I want it to be the fastest and most stable computer equipment on the face of the planet, so quality is what Fatal1ty Brand products represent.

Johnathan “Fatal1ty” Wendel

e Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are registered trademarks of Fatal1ty, Inc., and are used under license. © 2016 Fatal1ty, Inc. All rights reserved. All other trademarks are the property of their respective owners.

Fatal1ty E3V5 Performance Gaming/OC Series

DDR 4_A2 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

DDR 4_B2 (6 4 bit, 28 8-pin m odule )

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

ATX12V1

USB 2. 0

T: USB1

B: USB 2

ATXP WR 1

LAN

PCIE2

Top: RJ-45

USB 3.0 T: USB3 B: USB4

Top:

Central/Bass

Center :

REAR SPK

Top:

LINE IN

Center :

FRONT

Bottom :

Optica l

SPDIF

Bottom :

MIC IN

PCIE4

HDLED RESET

PLED PWRBTN

PANEL1

USB3_4

SPK_PLED1

COM1

HD_AUDIO1

E3V5 Performance Gaming/OC

PCIE1

RoHS

SATA3_1

Purity Sound 3

BIOS ROM

PS2

Keybo ard

/Mous e

CMOS

Battery

CLRMOS1

PCIE3

USB3_7 _8

CPU_FAN2

CPU_FAN1

CHA_FAN1

CHA_FAN4

USB1_2

TPMS1

PCIE5

CHA_FAN2

CHA_FAN3

PCIE_PWR1

SATA3_5 SATA3_3

SATA3_4 SATA3_2

SATA3_0

Intel

C232

USB 3.0 T: USB1 B: USB2

Motherboard Layout

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

4 CPU Fan Connector (CPU_FAN1)

5 ATX Power Connector (ATXPWR1)

6 Chassis Fan Connector (CHA_FAN4)

7 USB 3.0 Header (USB3_7_8)

8 SATA3 Connectors (SATA3_0_1)

9 CPU Fan Connector (CPU_FAN2)

10 SATA3 Connectors (SATA3_3_5)

11 SATA3 Connectors (SATA3_ 2_4)

12 Chassis Fan Connector (CHA_FAN2)

13 Chassis Fan Connector (CHA_FAN1)

14 System Panel Header (PANEL1)

15 Clear CMOS Jumper (CLRMOS1)

16 Power LED and Speaker Header (SPK_PLED1)

17 USB 2.0 Header (USB1_2)

18 USB 2.0 Header (USB3_4)

19 Chassis Fan Connector (CHA_FAN3)

20 TPM Header (TPMS1)

21 COM Port Header (COM1)

22 Front Panel Audio Header (HD_AUDIO1)

23 PCIe Power Connector (PCIE_PWR1)

English

1.4 I/O Panel

Fatal1ty E3V5 Performance Gaming/OC Series

No. Description No. Description

1 Fatal1ty Mouse Port (USB1) 7 Front Speaker (Lime)**

2 USB 2.0 Port (USB2) 8 Microphone (Pink)

3 LAN RJ-45 Port* 9 Optical SPDIF Out Port

4 Central / Bass (Orange) 10 USB 3.0 Ports (USB3_34)

5 Rear Speaker (Black) 11 USB 3.0 Ports (USB3_12)

6 Line In (Light Blue) 12 PS/2 Mouse/Keyboard Port

CAU TION: For operating system installation, be sure to plug your USB ash drive into the USB 2.0 Ports (USB12).

3 5

English

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

** If you use a 2- channel speaker, plea se connect the speake r’s plug into “Front Speaker Jack”. See the table below for connection d etails in accordance w ith the type of speaker you use.

English

Audio Output

Channels

Front Speaker

(No. 7)

Rear Speaker

(No. 5)

Central / Bass

(No. 4)

2 V -- -- -- 4 V V -- -- 6 V V V -- 8 V V V V

To enable Multi-Streaming, you need to connect a front panel audio cable to the front panel audio header. Aer restarting your computer, you will nd the “Mixer” tool on your system. Please select “Mixe r ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA Primary output” to use the Rear Speaker, Central/Ba ss, and Front Speaker, or select “Realtek HDA Audio 2nd output” to use the front panel audio.

Line In (No. 6)

Fatal1ty E3V5 Performance Gaming/OC Series

Chapter 1 Introduction

ank you for purchasing ASRock Fatal1ty E3V5 Performance Gaming/OC Series motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s website w ithout further notice. If you require technical support related to this motherboard, please visit our website for specic information about the model you are using. You may nd the l atest VGA cards and CPU support list on ASRock’s website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Motherboard (ATX Form

Fact or)

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Quick Installation Guide

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Support CD

•2 x Serial ATA (SATA) Data Cables (Optional)

•1 x I/O Panel Shield

English

1.2 Specications

Platform

CPU

Chipset

Memory

Expansion Slot

•ATX Form Factor

•Supports the Intel® Xeon® E3-1200 v5 Processor and 6

Generation Intel® CoreTM i3/Pentium®/Celeron® Processors (Socket 1151)

•Digi Power design

•10 Power Phase design

•Supports Intel® Turbo Boost 2.0 Technology

•Supports ASRock BCLK Full-range Overclocking

•Supports ASRock Hyper BCLK Engine

•Intel® C232

•Dual Channel DDR4 Memory Technology

•4 x DDR4 DIMM Slots

•Supports DDR4 2133 non-ECC, un-buered memory

•Supports ECC UDIMM memory modules

•Max. capacity of system memory: 64GB

•Supports Intel® Extreme Memory Prole (XMP) 2.0

•15μ Gold Contact in DIMM Slots

•2 x PCI Express 3.0 x16 Slots (PCIE2: x16 mode; PCIE4: x4

mode)* * Supports NVMe SSD as boot disks

•3 x PCI Express 3.0 x1 Slots (Flexible PCIe)

•Supports AMD Quad CrossFireX

•15μ Gold Contact in VGA PCIe Slot (PCIE2)

and CrossFireXTM

English

Audio

•7.1 CH HD Audio with Content Protection (Realtek

ALC1150 Audio Codec)

•Premium Blu-ray Audio support

•Supports Surge Protection (ASRock Full Spike Protection)

•Supports Purity Sound

Fatal1ty E3V5 Performance Gaming/OC Series

- Nichicon Fine Gold Series Audio Caps

- 115dB SNR DAC with Dierential Amplier

- TI® NE5532 Premium Headset Amplier (Supports up to 600 Ohm headsets)

- Pure Power-In

- Direct Drive Technology

- PCB Isolate Shielding

•Supports DTS Connect

LAN

Rear Panel I/O

Storage

•Gigabit LAN 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•Supports Wake-On-LAN

•Supports Lightning/ESD Protection (ASRock Full Spike

Protection)

•Supports Energy Ecient Ethernet 802.3az

•Supports PXE

•1 x PS/2 Mouse/Keyboard Port

•1 x Optical SPDIF Out Port

•1 x USB 2.0 Port (Supports ESD Protection (ASRock Full

Spike Protection))

•1 x Fatal1ty Mouse Port (USB 2.0) (Supports ESD Protection

(ASRock Full Spike Protection))

•4 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

Spike Protection))

•1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

LE D)

•HD Audio Jacks: Rear Speaker / Central / Bass / Line in /

Front Speaker / Microphone

•6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology enterprise), NCQ, AHCI and Hot Plug

English

Connector

•1 x COM Port Header

•1 x TPM Header

•1 x Power LED and Speaker Header

•2 x CPU Fan Connectors (4-pin) (Smart Fan Speed Control)

•4 x Chassis Fan Connectors (4-pin) (Smart Fan Speed Con-

trol) * CPU_FAN1 and CHA_FAN1 can auto detect if 3-pin or 4-pin fan is in use. * e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

•1 x 24 pin ATX Power Connector

•1 x 8 pin 12V Power Connector

•1 x PCIe Power Connector

•1 x Front Panel Audio Connector

•2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports

ESD Protection (ASRock Full Spike Protection))

•1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports

ESD Protection (ASRock Full Spike Protection))

English

BIOS Feature

Hardware Monitor

•AMI UEFI Legal BIOS with multilingual GUI support

•ACPI 5.0 Compliant wake up events

•SMBIOS 2.7 Support

•CPU, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VC-

CPLL, VCCSA Voltage Multi-adjustment

•CPU/Chassis temperature sensing

•CPU/Chassis Fan Tachometer

•CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

CPU temperature)

•CPU/Chassis Fan multi-speed control

•Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, GT_CPU,

DRAM, VPPM, PCH 1.0V, VCCIO, VCCSA

Fatal1ty E3V5 Performance Gaming/OC Series

•Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-

bit * To install Windows® 7 OS, a modied installation disk with xHCI drivers packed into the ISO le is required. Please refer to page 146 for more detailed instructions. * For the updated Windows® 10 driver, please visit ASRock ’s website for details: http://www.asrock.com.

Certications

* For detailed product information, please visit our website: http://www.asrock.com

Please realize that the re is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party overclocking tools. O verclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your ow n risk and expense. We are not responsible for possible damage caused by overclocking.

•FCC, CE, WHQL

•ErP/EuP ready (ErP/EuP ready power supply is required)

English

Chapter 2 Installation

is is an ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

•Make sure to unplug the power cord before installing or removing the motherboard

components. Failure to do so may cause physical injuries and damages to motherboard components.

•In order to avoid damage from static electricity to the motherboard’s components,

NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.

•Hold components by the edges and do not touch the ICs.

•Whenever you uninstall any components, place them on a grounded anti-static pad or

in the bag that comes with the components.

•When placing screws to secure the motherboard to the chassis, please do not over-

tighten the screws! Doing so may damage the motherboard.

English

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the sock et. Do not force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

2. Unplug all power cables before in stalling the CPU.

Fatal1ty E3V5 Performance Gaming/OC Series

English

Fatal1ty E3V5 Performance Gaming/OC Series

Please save and replace the cover if the processor i s removed. e cover must be placed if you wish to return the motherboard for aer service.

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

FAN

CPU_

Fatal1ty E3V5 Performance Gaming/OC Series

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.

1. For dual channel conguration , you always need to in stall identical (the same brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memor y Technology with only one or three memor y module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 sl ot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated 2 Populated Populated 3 Populated Populated Populated Populated

e DIMM only ts in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

English

Fatal1ty E3V5 Performance Gaming/OC Series

2.4 Expansion Slots (PCI Express Slots)

ere are 5 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE4 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.

PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards

For a better ther mal environment, please connect a chassi s fan to the motherboard’s chassis fan connector (CHA_ FAN1, CHA_ FAN2, CHA_FAN3 or CHA_ FAN4) when u sing multiple graphics cards.

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. e illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”

when a jumper cap is placed on these 2 pins.

Clear CMOS Jumper (C LR MOS 1) (see p.1, No. 15)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed.

Clear CMOSDefault

English

Fatal1ty E3V5 Performance Gaming/OC Series

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these heade rs and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

System Panel Header (9-pi n PANEL1) (see p.1, No. 14)

PWRBTN (Power Switch):

Connec t to the power switch on the chassi s front panel. You may congure the way to tur n o your system using the power switch.

RESET (Reset Switch): Connec t to the reset switch on the chassis front panel. Press the reset sw itch to restart the computer if the computer f reezes and fails to perform a normal restar t.

PLED (Syste m Power LED): Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED): Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the hard drive is reading or wr iting data.

e front panel design may dier by chassis. A front panel module mainly consists of power switch, reset switch , power LED, hard dr ive activity LED, speaker and etc. When connecting your chassi s front panel module to thi s header, make sure the wire a ssignments and the pin assignments are matched correctly.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

English

Power LED and Speaker

PLED-

SPEAKER

Header (7-pin SPK_PLED1) (see p.1, No. 16)

DUMMY +5V

PLED+

DUMMY

PLED+

Please connect the chassis power LED and the chassis speaker to this header.

Serial ATA3 Connectors (SATA3_0_1: see p.1, No. 8) (SATA3_2_4: see p.1, No. 11) (SATA3_3_5: see p.1, No. 10)

USB 2.0 Headers (9-pin USB1_2) (see p.1, No. 17) (9-pin USB3_4) (see p.1, No. 18)

USB 3.0 Header (19-pin USB3_7_8) (see p.1, No. 7)

SATA3_5

SATA3_3

USB_PWR

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

SATA3_1

-B

-A

GND

SATA3_4

SATA3_2

DUMMY

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

ese six SATA3 connectors support SATA data cables for internal

SATA3_0

storage devices with up to

6.0 Gb/s data transfer rate.

ere are two headers on this motherboard. Each USB 2.0 header can support two ports.

Besides four USB 3.0 ports on the I/O panel, there is one header on this motherboard. Each USB

3.0 header can support two ports.

English

Fatal1ty E3V5 Performance Gaming/OC Series

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

is header is for connecting audio devices to the front audio panel.

Front Panel Audio Header (9-pin HD_ AUDIO1) (see p.1, No. 22)

1. High Denition Audio support s Jack Sensing, but the panel wire on the chassis must sup port HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.

2. If you use an AC’97 audio panel , please install it to the front panel audio header by the steps below: A. Connect Mic_IN (MIC) to MIC2_ L. B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel . E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.

Chassis Fan Connectors (4-pin CHA_FAN1) (see p.1, No. 13) (4-pin CHA_FAN2)

4 3 2 1

GND

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

Please connect fan cables to the fan connectors and match the black wire to

the ground pin. (see p.1, No. 12) (4-pin CHA_FAN3) (see p.1, No. 19)

(4-pin CHA_FAN4) (see p.1, No. 6)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

English

CPU Fan Connectors

(4-pin CPU_FAN1) (see p.1, No. 4)

(4-pin CPU_FAN2) (see p.1, No. 9)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND FAN_VOLTAGE CPU_FAN_SPEED FAN_SPEED_CONTROL

is motherboard provides two 4-Pin CPU fan (Quiet Fan) connectors. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

ATX Power Connector (24-pin ATXPWR1) (see p.1, No. 5)

ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 1)

Serial Port Header (9-pin COM1) (see p.1, No. 21)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

is motherboard provides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin

13.

is motherboard provides an 8-pin ATX 12V power connector. To use a 4-pin ATX power supply, please plug it along Pin 1 and Pin 5.

is COM1 header supports a serial port module.

English

Fatal1ty E3V5 Performance Gaming/OC Series

TPM Header (17-pi n TPMS1) (see p.1, No. 20)

PCIe Power Connector (4-pin PC IE_PWR1) (see p.1, No. 23)

GN D

LAD 0

+3V S B

GN D

SER IRQ #

S_P WRD WN #

+12V DETECT

+3 V

LAD 1

GND

is connector supports Trusted

Platform Module (TPM) system,

PC ICL K

LAD 3

PC IRS T #

FRA M E

which can securely store keys,

digital certicates, passwords,

GN D

LAD 2

SMB _CL K_M AIN

SMB _DA TA_ MAI N

and data. A TPM system also

helps enhance network security,

protects digital identities, and

ensures platform integrity.

Please connect a 4 pin molex

power cable to this connector

when more than three graphics

cards are installed.

English

1 Einleitung

Vielen Dank, dass Sie sich für die ASRock Fatal1ty E3V5 Performance Gaming/OC Series entschieden haben – ein zuverlässiges Motherboard, das konsequent unter der strengen Qualitätskontrolle von ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design, das ASRocks Streben nach Qualität und Beständigkeit erfüllt.

Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden. Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten Sie technische Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer Webseite spezischen Informationen über das von Ihnen verwendete Modell. Auch nden Sie eine aktuelle Liste unterstützter VGA-Karten und Prozessoren auf der ASRock-Webseite: ASRock-Website http://www.asrock.com.

1.1 Lieferumfang

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series-Motherboard (ATX-Formfaktor)

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series-Schnellinstallationsanleitung

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series-Unterstützungs-CD

•2 x Serial-ATA- (SATA) Datenkabel (optional)

•1 x E/A-Blendenabschirmung

Deutsch

1.2 Technische Daten

Fatal1ty E3V5 Performance Gaming/OC Series

Plattform

Prozessor

Chipsatz

Speicher

Erweiterungssteckplatz

•ATX-Formfaktor

•Unterstützt die Prozessoren Intel® Xeon E3-1200 v5 und

Prozessoren Intel® CoreTM i3/Pentium®/Celeron® der 6. Generation (Sockel 1151)

•Digipower-Design

•10-Leistungsphasendesign

•Unterstützt Intel® Turbo Boost 2.0-Technologie

•Unterstützt ASRock BCLK-Übertaktung (voller Bereich)

•Unterstützt ASRock-Hyper-BCLK-Engine

•Intel® C232

•Dualkanal-DDR4-Speichertechnologie

•4 x DDR4-DIMM-Steckplätze

•Unterstützt DDR4 2133 non-ECC, ungepuerter Speicher

•Unterstützt ECC-UDIMM-Speichermodule

•Systemspeicher, max. Kapazität: 64GB

•Unterstützt Intel® Extreme Memory Prole (XMP) 2.0

•15-μ-Goldkontakt in DIMM-Steckplätze

•2 x PCI-Express 3.0-x16-Steckplätze (PCIE2:x16-Modus;

PCIE4:x4-Modus)* * Unterstützt NVMe-SSD als Bootplatte

•3 x PCI-Express 3.0-x1-Steckplätze (Flexible PCIe)

•Unterstützt AMD Quad CrossFireX

•15-μ-Goldkontakt in VGA-PCIe-Steckplatz (PCIE2)

und CrossFireXTM

Audio

•7.1-Kanal-HD-Audio mit Inhaltsschutz (Realtek ALC1150-

Audiocodec)

•Erstklassige Blu-ray-Audiounterstützung

•Unterstützt Überspannungsschutz (ASRock Full Spike

Protection)

Deutsch

•Unterstützt Purity Sound

- Nichicon-Audiokappen der Fine Gold-Serie

- 115-dB-SRV-DAC mit Dierentialverstärker

- TI® NE5532 – erstklassiger Headset-Verstärker (unterstützt Headsets mit bis zu 600 Ohm)

- Pure Power-Eingang

- Direct Drive Technology

- PCB-isolierte Abschirmung

•Unterstützt DTS Connect

Deutsch

LAN

Rückblende, E/A

Speicher

•Gigabit LAN 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•Unterstützt Wake-On-LAN

•Unterstützt Blitzschutz/Schutz gegen elektrostatische Entla-

dung (ASRock Full Spike Protection)

•Unterstützt energieezientes Ethernet 802.3az

•Unterstützt PXE

•1 x PS/2-Maus-/Tastaturanschluss

•1 x Optischer SPDIF-Ausgang

•1 x USB 2.0-Port (unterstützt Schutz gegen elektrostatische

Entladung (ASRock Full Spike Protection))

•1 x Fatal1ty-Mausport (USB 2.0) (unterstützt Schutz gegen

elektrostatische Entladung (ASRock Full Spike Protection))

•4 x USB 3.0-Ports (unterstützt Schutz gegen elektrostatische

Entladung (ASRock Full Spike Protection))

•1 x RJ-45-LAN-Port mit LED (Aktivität/Verbindung-LED und

Geschwindigkeit-LED)

•HD-Audioanschlüsse: Hintere Lautsprecher / Zentral / Bass /

Line-in / Vorderer Lautsprecher / Mikrofon

•6 x SATA-III-6,0-Gb/s-Anschlüsse, unterstützt RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel RSTe), NCQ, AHCI und HotPlugging

Anschluss

•1 x COM-Anschluss-Stileiste

•1 x TPM-Stileiste

•1 x Betrieb-LED- und Lautsprecher-Stileiste

Fatal1ty E3V5 Performance Gaming/OC Series

•2 x CPU-Lüeranschlüsse (4-polig) (intelligente

Lüergeschwindigkeitssteuerung)

•4 x Gehäuselüeranschlüsse (4-polig) (intelligente

Lüergeschwindigkeitssteuerung)

•1 x 24-poliger ATX-Netzanschluss

•1 x 8-poliger 12-V-Netzanschluss

•1 x PCIe-Netzanschluss

•1 x Audioanschluss an Frontblende

•2 x USB 2.0-Stileisten (unterstützen 4 USB 2.0-Ports)

(unterstützt Schutz gegen elektrostatische Entladung (ASRock Full Spike Protection))

•1 x USB 3.0-Stileiste (unterstützt 2 USB 3.0-Ports) (unterstützt

Schutz gegen elektrostatische Entladung (ASRock Full Spike Protection))

BIOS-Funktion

Hardwareüberwachung

Betriebssystem

•AMI-UEFI-Legal-BIOS mit Unterstützung mehrsprachiger

grascher Benutzerschnittstellen

•ACPI 5.0-konforme Aufweckereignisse

•SMBIOS 2.7-Unterstützung

•CPU, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VCCPLL,

VCCSA Mehrfachspannungsanpassung

•CPU-/Gehäusetemperaturerkennung

•CPU-/Gehäuselüertachometer

•Lautloser CPU-/Gehäuselüer (automatische Anpassung der

Gehäuselüergeschwindigkeit durch CPU-Temperatur)

•CPU-/Gehäuselüer-Mehrfachgeschwindigkeitssteuerung

•Spannungsüberwachung: +12 V, +5 V, +3,3 V, CPU Vcore, GT_

CPU, DRAM, VPPM, PCH 1,0 V, VCCIO, VCCSA

•Microso® Windows® 10 64 Bit / 8.1 64 Bit / 7 32 Bit / 7 64 Bit

* Zur Installation einer Windows® 7-Betriebssystems wird ein modiziertes Installationslaufwerk mit xHCI-Treibern in der ISO-Datei benötigt. Detaillierte Anweisungen nden Sie auf Seite

146. * Einzelheiten zum aktualisierten Windows® 10-Treiber entnehmen Sie bitte der ASRock-Webseite: http://www.asrock. com.

Deutsch

Zertizierungen

* Detaillierte Produktinformationen nden Sie auf unserer Webseite: http://www.asrock.com

Bitte beachten Sie, dass mit einer Übertaktung, zu der die Anpassung von BIOS-Einstellungen, die Anwendung der Untied Overclocking Technology oder die Nutzung von Übertaktungswerkzeugen von Drittanbietern zählen, bestimmte Risiken verbunden sind. Eine Übertaktung kann sich auf die Stabilität Ihres Systems auswirken und sogar Komponenten und Geräte Ihres Systems beschädigen. Sie sollte auf eigene Gefahr und eigene Kosten durchgeführt werden. Wir übernehmen keine Verantwortung für mögliche Schäden, die durch eine Übertaktung verursacht wurden.

•FCC, CE, WHQL

•ErP/EuP ready (ErP/EuP ready-Netzteil erforderlich)

Deutsch

Fatal1ty E3V5 Performance Gaming/OC Series

1.3 Jumpereinstellung

Die Abbildung zeigt, wie die Jumper eingestellt werden. Wenn die Jumper-Kappe auf den Kontakten angebracht ist, ist der Jumper „kurzgeschlossen“. Wenn keine JumperKappe auf den Kontakten angebracht ist, ist der Jumper „oen“. Die Abbildung zeigt einen 3-poligen Jumper, dessen Kontakt 1 und Kontakt 2 „kurzgeschlossen“ sind, wenn eine Jumper-Kappe auf diesen 2 Kontakten angebracht ist.

CMOS-löschen-Jumper (CLRMOS1) (siehe S. 1, Nr. 15)

CLRMOS1 ermöglicht Ihnen die Löschung der Daten im CMOS. Zum Löschen und Rücksetzen der Systemparameter auf die Standardeinrichtung schalten Sie den Computer bitte ab und ziehen das Netzkabel aus der Steckdose. Warten Sie 15 Sekunde, schließen Sie dann Kontakt 2 und Kontakt 3 an CLRMOS1 5 Sekunden lang mit einer Jumper-Kappe kurz. Löschen Sie den CMOS jedoch nicht direkt nach der BIOS-Aktualisierung. Falls Sie den CMOS direkt nach Abschluss der BIOSAktualisierung löschen müssen, starten Sie das System zunächst; fahren Sie es dann vor der CMOS-Löschung herunter. Bitte beachten Sie, dass Kennwort, Datum, Zeit und Benutzerstandardprol nur gelöscht werden, wenn die CMOS-Batterie entfernt wird.

CMOS löschenStandard

Deutsch

1.4 Integrierte Stiftleisten und Anschlüsse

Integrierte Stileisten und Anschlüsse sind KEINE Jumper. Bringen Sie KEINE Jumper-Kappen an diesen Stileisten und Anschlüssen an. Durch Anbringen von Jumper-Kappen an diesen Stileisten und Anschlüssen können Sie das Motherboard dauerha beschädigen.

Deutsch

Systemblende-Stileiste (9-polig, PANEL1) (siehe S. 1, Nr. 14)

PWRBTN (Ein-/Austaste):

Mit der Ein-/Austaste an der Frontblende des Gehäuses verbinden. Sie können die Abschaltung Ihres Systems über die Ein-/Austaste kongurieren.

RESET (Reset-Taste):

Mit der Reset-Taste an der Frontblende des Gehäuses verbinden. Starten Sie den Computer über die Reset-Taste neu, wenn er abstürzt oder sich nicht normal neu starten lässt.

PLED (Systembetriebs-LED):

Mit der Betriebsstatusanzeige an der Frontblende des Gehäuses verbinden. Die LED leuchtet, wenn das System läu. Die LED blinkt, wenn sich das System im S1/S3-Ruhezustand bendet. Die LED ist aus, wenn sich das System im S4-Ruhezustand bendet oder ausgeschaltet ist (S5).

HDLED (Festplattenaktivitäts-LED):

Mit der Festplattenaktivitäts-LED an der Frontblende des Gehäuses verbinden. Die LED leuchtet, wenn die Festplatte Daten liest oder schreibt. Das Design der Frontblende kann je nach Gehäuse variieren. Ein Frontblendenmodul besteht hauptsächlich aus Ein-/Austaste, Reset-Taste, Betrieb-LED, Festplattenaktivität-LED, Lautsprecher etc. Stellen Sie beim Anschließen Ihres Frontblendenmoduls an diese Stileiste sicher, dass Kabel- und Pinbelegung richtig abgestimmt sind.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Verbinden Sie Netzschalter, Reset-Taste und Systemstatusanzeige am Gehäuse entsprechend der nachstehenden Pinbelegung mit dieser Stileiste. Beachten Sie vor Anschließen der Kabel die positiven und negativen Kontakte.

Fatal1ty E3V5 Performance Gaming/OC Series

PLED-

SPEAKER

Betrieb-LED- und Lautsprecher-Stileiste (7-polig, SPK_PLED1) (siehe S. 1, Nr. 16)

Serial-ATA-III-Anschlüsse (SATA3_0_1: siehe S. 1, Nr. 8) (SATA3_2_4: siehe S. 1, Nr. 11) (SATA3_3_5: siehe S. 1, Nr. 10)

USB 2.0-Stileisten (9-polig, USB1_2 (siehe S. 1, Nr. 17) (9-polig, USB3_4) (siehe S. 1, Nr. 18)

DUMMY +5V

PLED+

SATA3_1

SATA3_5

SATA3_3

USB_PWR

-B

-A

USB_PWR

DUMMY

PLED+

SATA3_4

SATA3_2

GND

DUMMY

Bitte verbinden Sie die Betrieb-LED des Gehäuses und den Gehäuselautsprecher mit dieser Stileiste.

Diese sechs SATA-IIIAnschlüsse unterstützen SATA-Datenkabel für

SATA3_0

interne Speichergeräte mit einer Datenübertragungsge schwindigkeit bis 6,0 Gb/s.

Es gibt zwei Stileisten an diesem Motherboard. Jede USB 2.0-Stileiste kann zwei Ports unterstützen.

USB 3,0-Stileiste (19-polig, USB3_7_8) (siehe S. 1, Nr. 7)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Neben vier USB 3.0-Ports an der E/A-Blende bendet sich eine Stileiste an diesem Motherboard. Jede USB 3.0-Stileiste kann zwei Ports unterstützen.

Deutsch

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

Diese Stileiste dient dem Anschließen von Audiogeräten an der Frontblende.

Audiostileiste (Frontblende) (9-polig, HD_AUDIO1) (siehe S. 1, Nr. 22)

1. High Denition Audio unterstützt Anschlusserkennung, der Draht am Gehäuse muss dazu jedoch HDA unterstützt. Bitte befolgen Sie zum Installieren Ihres Systems die Anweisungen in unserer Anleitung und der Anleitung zum Gehäuse.

2. Bei Nutzung eines AC’97-Audiopanels dieses bitte anhand folgender Schritte an der Audiostileiste der Frontblende installieren: A. Mic_IN (Mikrofon) mit MIC2_L verbinden. B. Audio_R (RIN) mit OUT2_R und Audio_L (LIN) mit OUT2_L verbinden. C. Erde (GND) mit Erde (GND) verbinden. D. MIC_RET und OUT_RET sind nur für das HD-Audiopanel vorgesehen. Sie müssen sie nicht für das AC’97-Audiopanel verbinden. E. Rufen Sie zum Aktivieren des vorderen Mikrofons das „FrontMic (Vorderes Mikrofon)“-Register in der Realtek-Systemsteuerung auf und passen „Recording Volume (Aufnahmelautstärke)“ an.

Deutsch

Gehäuselüeranschlüsse (4-polig, CHA_FAN1) (siehe S. 1, Nr. 13) (4-polig, CHA_FAN2) (siehe S. 1, Nr. 12) (4-polig, CHA_FAN3) (siehe S. 1, Nr. 19)

(4-polig, CHA_FAN4) (siehe S. 1, Nr. 6)

GND

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

Bitte verbinden Sie die Lüerkabel mit den Lüeranschlüssen; der schwarze Draht gehört zum Erdungskontakt.

Fatal1ty E3V5 Performance Gaming/OC Series

CPU-Lüeranschlüsse (4-polig, CPU_FAN1) (siehe S. 1, Nr. 4)

(4-polig, CPU_FAN2) (siehe S. 1, Nr. 9)

ATX-Netzanschluss (24-polig, ATXPWR1) (siehe S. 1, Nr. 5)

ATX-12-V-Netzanschluss (8-polig, ATX12V1) (siehe S. 1, Nr. 1)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND

FAN_VOLTAGE

CPU_FAN_SPEED

FAN_SPEED_CONTROL

Dieses Motherboard bietet zwei 4-polige CPULüeranschlüsse (lautloser Lüer). Falls Sie einen 3-poligen CPU-Lüer anschließen möchten, verbinden Sie ihn bitte mit Kontakt 1 bis 3.

Dieses Motherboard bietet einen 24-poligen ATX-Netzanschluss. Bitte schließen Sie es zur Nutzung eines 20-poligen ATX-Netzteils entlang Kontakt 1 und Kontakt 13 an.

Dieses Motherboard bietet einen 8-poligen ATX12-V-Netzanschluss. Bitte schließen Sie es zur Nutzung eines 4-poligen ATX-Netzteils entlang Kontakt 1 und Kontakt 5 an.

Serieller-Port-Stileiste (9-polig, COM1) (siehe S. 1, Nr. 21)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Diese COM1-Stileiste unterstützt ein Modul für serielle Ports.

Deutsch

TPM-Stileiste (17-polig, TPMS1) (siehe S. 1, Nr. 20)

Dieser Anschluss unterstützt das

GN D

LAD 0

LAD 3

+3 V

PC IRS T #

+3V S B

GN D

SER IRQ #

S_P WRD WN #

FRA M E

LAD 1

LAD 2

SMB _CL K_M AIN

SMB _DA TA_ MAI N

Trusted Platform Module- (TPM)

PC ICL K

System, das Schlüssel, digitale

Zertikate, Kennwörter und Daten

GN D

sicher auewahren kann. Ein TPM-System hil zudem bei der Stärkung der Netzwerksicherheit, schützt digitale Identitäten und gewährleistet die Plattformintegrität.

Deutsch

PCIe-Netzanschluss (4-polig, PCIE_PWR1) (siehe S. 1, Nr. 23)

GND

+12V DETECT

Bitte verbinden Sie ein 4-poliges Molex-Netzkabel mit diesem Anschluss, wenn mehr als drei Grakkarten installiert sind.

Fatal1ty E3V5 Performance Gaming/OC Series

1 Introduction

Nous vous remercions d’avoir acheté cette carte mère ASRock Fatal1ty E3V5 Performance Gaming/OC Series, une carte mère able fabriquée conformément au contrôle de qualité rigoureux et constant appliqué par ASRock. Fidèle à son engagement de qualité et de durabilité, ASRock vous garantit une carte mère de conception robuste aux performances élevées.

Les spécications de la carte mère et du logiciel BIOS pouvant être mises à jour, le contenu de ce document est soumis à modication sans préavis. En cas de modications du présent document, la version mise à jour sera disponible sur le site Internet ASRock sans notication préalable. Si vous avez besoin d’une assistance technique pour votre carte mère, veuillez visiter notre site Internet pour plus de détails sur le modèle que vous utilisez. La liste la plus récente des cartes VGA et des processeurs pris en charge est également disponible sur le site Internet de ASRock. Site Internet ASRock http://www.asrock.com.

1.1 Contenu de l’emballage

•Carte mère ASRock Fatal1ty E3V5 Performance Gaming/OC Series (facteur de forme

AT X)

•Guide d’installation rapide ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•CD d’assistance ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•2 x câbles de données Serial ATA (SATA) (Optionnel)

•1 x panneau de protection E/S

Français

1.2 Spécications

Français

Plateforme

Processeur

Chipset

Mémoire

Fente d’expansion

•Facteur de forme ATX

•Prend en charge les processeurs Intel® Xeon® E3-1200 v5 et les

processeurs 6e génération Intel® CoreTM i3/Pentium®/Celeron® (Socket 1151)

•Conception Digi Power

•Alimentation à 10 phases

•Prend en charge la technologie Intel® Turbo Boost 2.0

•Prend en charge l’overclocking ASRock BCLK Full-range

•Prend en charge le moteur ASRock Hyper BCLK

•Intel® C232

•Technologie mémoire double canal DDR4

•4 x fentes DIMM DDR4

•Prend en charge les mémoires sans tampon non ECC DDR4

2133

•Prend en charge les modules mémoire UDIMM ECC

•Capacité max. de la mémoire système : 64GB

•Prend en charge Intel® Extreme Memory Prole (XMP) 2.0

•Contacts dorés 15μ sur fentes DIMM

•2 x fentes PCI Express 3.0 x 16 (PCIE2:mode x16 ;

PCIE4:mode x4)* * Prend en charge les SSD NVMe comme disques de démarrage

•3 x fentes PCI Express 3.0 x1 (PCIe exible)

•Prend en charge AMD Quad CrossFireX

•Contact doré 15μ dans fente VGA PCIe (PCIE2)

et CrossFireXTM

Audio

•Audio 7.1 CH HD avec protection du contenu (codec audio

Realtek ALC1150)

•Compatible audio Blu-ray Premium

•Protection contre les surtensions (Protection complète contre

les pics ASRock)

Fatal1ty E3V5 Performance Gaming/OC Series

Réseau

Connectique du panneau arrière

•Prend en charge Purity Sound

- Couvercles audio série en or n Nichicon

- 115dB SNR DAC avec amplicateur diérentiel

- Amplicateur de casque TI® NE5532 Premium (prend en charge les casques jusqu’à 600 Ohm)

- Alimentation Pure

- Technologie Direct Drive

- Blindage isolant PCB

•Prend en charge DTS Connect

•Gigabit LAN 10/100/1000 Mo/s

•Giga PHY Intel® I219V

•Prend en charge la fonction Wake-On-LAN

•Protection contre les orages/décharges électrostatiques

(Protection complète contre les pics ASRock)

•Prend en charge la fonction d’économie d’énergie Ethernet

802.3az

•Prend en charge PXE

•1 x port souris/clavier PS/2

•1 x port sortie optique SPDIF

•1 x port USB 2.0 (Protection contre les décharges

électrostatiques (Protection complète contre les pics ASRock))

•1 x ports souris Fatal1ty (USB 2.0) (Protection contre les

décharges électrostatiques (Protection complète contre les pics ASRock))

•4 x ports USB 3.0 (Protection contre les décharges

électrostatiques (Protection complète contre les pics ASRock))

•1 x port RJ-45 LAN avec LED (LED ACT/LIEN et LED

VITESSE)

•Connecteurs jack audio HD : Haut-parleur arrière / central /

basses / entrée ligne / haut-parleur avant / microphone

Stockage

•6 x connecteurs SATA3 6,0 Gb/s, compatibles RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel RSTe), fonctions NCQ, AHCI et «Hot Plug»

Français

Connecteur

•1 x embase pour port COM

•1 x embase TPM

•1 x prise DEL d’alimentation et haut-parleur

•2 x connecteurs pour ventilateur de processeur (4 broches)

(contrôle de vitesse de ventilateur intelligent)

•4 x connecteurs pour ventilateur du châssis (4 broches) (con-

trôle de vitesse de ventilateur intelligent)

•1 x connecteur d’alimentation ATX 24 broches

•1 x connecteur d’alimentation 12V 8 broches

•1 x connecteur d’alimentation PCIe

•1 x connecteur audio panneau frontal

•2 x embases USB 2.0 (4 ports USB 2.0 pris en charge) (Protec-

tion contre les décharges électrostatiques (Protection complète contre les pics ASRock))

•1 x embase USB 3.0 (2 ports USB 3.0 pris en charge) (Protection

contre les décharges électrostatiques (Protection complète contre les pics ASRock))

Français

Caractéristiques du BIOS

Surveillance du matériel

Système d’exploitation

•BIOS UEFI AMI avec prise en charge d’interface graphique

multilingue

•Compatible ACPI 5.0 Wake Up Events

•Prend en charge SMBIOS 2.7

•Réglage de la tension CPU, GT_CPU, DRAM, VPPM, PCH

1.0V, VCCIO, VCCPLL, VCCSA

•Détection de la température du processeur/châssis

•Tachéomètre ventilateur processeur/châssis

•Ventilateur silencieux processeur/châssis (réglage

automatique de la vitesse du ventilateur du châssis d’après la température du processeur)

•Contrôle simultané des vitesses des ventilateurs processeur/

châssis

•Surveillance de la tension d’alimentation : +12V, +5V, +3,3V,

CPU Vcore, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VCCSA

•Microso® Windows® 10 64 bits / 8.1 64 bits / 7 32 bits / 7 64 bits

* Pour installer Windows® 7, un disque d'installation modié avec les pilotes xHCI intégrés au chier ISO est requis. Reportez-vous à la page 146 pour des instructions plus détaillées. * Pour le pilote mis à jour pour Windows® 10, veuillez visiter le site Web d’ASRock pour plus de détails: http://www.asrock.com.

Fatal1ty E3V5 Performance Gaming/OC Series

Certications

•FCC, CE, WHQL

•ErP/EuP Ready (alimentation ErP/EuP ready requise)

* pour des informations détaillées de nos produits, veuillez visiter notre site: http://www.asrock.com

Il est important de signaler que l’overcloking présente certains risques, incluant des modications du BIOS, l’application d’une technologie d’overclocking déliée et l’utilisation d’outils d’overclocking développés par des tiers. La stabilité de votre système peut être aectée par ces pratiques, voire provoquer des dommages aux composants et aux périphériques du système. L’overclocking se fait à vos risques et périls. Nous ne pourrons en aucun cas être tenus pour responsables des dommages éventuels provoqués par l’overclocking.

Français

1.3 Conguration des cavaliers (jumpers)

L’illustration ci-dessous vous renseigne sur la conguration des cavaliers (jumpers). Lorsque le capuchon du cavalier est installé sur les broches, le cavalier est «courtcircuité». Si le capuchon du cavalier n’est pas installé sur les broches, le cavalier est «ouvert». L’illustration représente un cavalier à 3 broches dont les broches 1 et 2 sont «court-circuitées» si un capuchon de cavalier est posé sur ces 2 broches.

Cavalier Clear CMOS (CLRMOS1) (voir p.1, No. 15)

CLRMOS1 vous permet d’eacer les donnés de la CMOS. Pour eacer les paramètres du système et rétablir les valeurs par défaut, veuillez éteindre votre ordinateur et débrancher son cordon d’alimentation. Patientez 15 secondes, puis utilisez un capuchon de cavalier pour court-circuiter la broche 2 et la broche 3 sur CLRMOS1 pendant 5 secondes. Toutefois, n’eacez pas la CMOS immédiatement après avoir mis à jour le BIOS. Si vous avez besoin d’eacer les données CMOS après une mise à jour du BIOS, vous devez tout d’abord redémarrer le système, puis l’éteindre avant de procéder à l’eacement de la CMOS. Veuillez noter que les paramètres mot de passe, date, heure et prol de l’utilisateur seront uniquement eacés en cas de retrait de la pile de la CMOS.

Fonction Clear CMOSPar défaut

Français

Fatal1ty E3V5 Performance Gaming/OC Series

1.4 Embases et connecteurs de la carte mère

Les embases et connecteurs situés sur la carte NE SONT PAS des cavaliers. Ne placez JAMAIS de capuchons de cavaliers sur ces embases ou connecteurs. Placer un capuchon de cavalier sur ces embases ou connecteurs endommagera irrémédiablement votre carte mère.

Embase du panneau système (PANNEAU1 à 9 broches) (voir p.1, No. 14)

PWRBTN (bouton d’alimentation) :

pour brancher le bouton d’alimentation du panneau frontal du châssis. Vous pouvez congurer la façon dont votre système doit s’arrêter à l’aide du bouton de mise en marche.

RESET (bouton de réinitiélisation) :

pour brancher le bouton de réinitialisation du panneau frontal du châssis. Appuyez sur le bouton de réinitialisation pour redémarrer l’ordinateur en cas de plantage ou de dysfonctionnement au démarrage.

PLED (LED d’alimentation du système) :

pour brancher le témoin d’état de l’alimentation du panneau frontal du châssis. Le LED est allumé lorsque le système fonctionne. Le LED clignote lorsque le système se trouve en mode veille S1/S3. Le LED est éteint lorsque le système se trouve en mode veille S4 ou hors tension (S5).

HDLED (LED d’activité du disque dur) :

pour brancher le témoin LED d’activité du disque dur du panneau frontal du châssis. Le LED est allumé lorsque le disque dur lit ou écrit des données.

La conception du panneau frontal peut varier en fonction du châssis. Un module de panneau frontal est principalement composé d’un bouton de mise en marche, bouton de réinitialisation, LED d’alimentation, LED d’activité du disque dur, haut-parleur etc. Lorsque vous reliez le module du panneau frontal de votre châssis sur cette embase, veillez à parfaitement faire correspondre les ls et les broches.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Branchez le bouton de mise en marche, le bouton de réinitialisation et le témoin d’état du système présents sur le châssis sur cette embase en respectant la conguration des broches illustrée ci-dessous. Repérez les broches positive et négative avant de brancher les câbles.

Français

Prise DEL d’alimentation

PLED-

SPEAKER

et haut-parleur (SPK_PLED1 à 7 broches) (voir p.1, No. 16)

DUMMY +5V

PLED+

DUMMY

PLED+

Veuillez brancher la DEL d'alimentation du châssis et le haut-parleur du châssis sur ce connecteur.

Français

Connecteurs Serial ATA3 (SATA3_0_1: voir p.1, No. 8) (SATA3_2_4: voir p.1, No. 11) (SATA3_3_5: voir p.1, No. 10)

Embases USB 2.0 (USB1_2 9broches (voir p.1, No. 17) (USB3_4 à 9 broches) (voir p.1, No. 18)

Embases USB 3.0 (USB3_7_8 19 broches) (voir p.1, No. 7)

SATA3_5

SATA3_3

USB_PWR

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

SATA3_1

-B

-A

SATA3_4

SATA3_2

GND

DUMMY

GND

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Ces six connecteurs SATA3 sont compatibles avec les câbles de données SATA

SATA3_0

pour les appareils de stockage internes avec un taux de transfert maximal de 6,0 Go/s.

Cette carte mère comprend deux connecteurs. Chaque embase USB 2,0 peut prendre en charge deux ports.

En plus des quatre ports USB 3.0 sur le panneau E/S, cette carte mère est dotée d’une embase supplémentaire. Chaque embase USB 3.0 peut prendre en charge deux ports..

Fatal1ty E3V5 Performance Gaming/OC Series

Embase audio du panneau frontal (HD_AUDIO1 à 9 broches) (voir p.1, No. 22)

1. L’audio haute dénition prend en charge la technologie Jack Sensing (détection de la che), mais le panneau grillagé du châssis doit être compatible avec la HDA pour fonctionner correctement. Veuillez suivre les instructions gurant dans notre manuel et dans le manuel du châssis pour installer votre système.

2. Si vous utilisez un panneau audio AC’97, veuillez le brancher sur l’embase audio du panneau frontal en procédant comme suit : A. branchez Mic_IN (MIC) sur MIC2_L. B. branchez Audio_R (RIN) sur OUT2_R et Audio_L (LIN) sur OUT2_L. C. branchez la mise à terre (GND) sur mise à terre (GND). D. MIC_RET et OUT_RET sont exclusivement réservés au panneau audio HD. Il est inutile de les brancher avec le panneau audio AC’97. E. Pour activer le micro frontal, sélectionnez l’onglet «FrontMic» du panneau de contrôle Realtek et réglez le paramètre «Volume d’enregistrement».

Connecteurs du ventilateur du châssis (CHA_FAN1 à 4 broches) (voir p.1, No. 13) (CHA_FAN2 à 4 broches)

GND

PRESENCE#

MIC_RET

OUT_RET

FAN_SPEED

FAN_SPEED_CONTROL

J_SENSE

OUT2_R

MIC2_R

MIC2_L

GND

FAN_VOLTAGE

OUT2_L

Cette embase sert au branchement des appareils audio au panneau audio frontal.

Veuillez brancher les câbles du ventilateur sur les connecteurs du ventilateur, puis reliez le l noir à la

broche de mise à terre. (voir p.1, No. 12) (CHA_FAN3 à 4 broches) (voir p.1, No. 19)

(CHA_FAN4 4 broches) (voir p.1, No. 6)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

Connecteurs du ventilateur du processeur (CPU_FAN1 à 4 broches) (voir p.1, No. 4)

(CPU_FAN2 à 4 broches) (voir p.1, No. 9)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND

FAN_VOLTAGE

CPU_FAN_SPEED

FAN_SPEED_CONTROL

Cette carte mère est dotée

de deux connecteurs pour

ventilateur de processeur

(Quiet Fan) à 4 broches.

Si vous envisagez de

connecter un ventilateur

de processeur à 3 broches,

veuillez le brancher sur la

Broche 1-3.

Français

Connecteur d’alimentation

AT X (ATXPWR1 à 24 broches) (voir p.1, No. 5)

Cette carte mère est dotée d’un connecteur d’alimentation ATX à 24 broches. Pour utiliser une alimentation ATX à 20 broches, veuillez eectuer

les branchements sur la Broche 1 et la Broche 13.

Français

Connecteur d’alimentation ATX 12V (ATX12V1 à 8 broches) (voir p.1, No. 1)

Embase pour port série (COM1 à 9 broches) (voir p.1, No. 21)

Embase TPM (TPMS1 à 17 broches) (voir p.1, No. 20)

Cette carte mère est dotée d’un connecteur d’alimentation ATX 12V à 8 broches. Pour utiliser une alimentation ATX à 4 broches, veuillez eectuer les branchements sur la Broche 1 et la Broche 5.

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Cette embase COM1 prend en charge un module de port série.

Ce connecteur prend en charge un

GN D

LAD 0

LAD 3

+3 V

PC IRS T #

+3V S B

GN D

SER IRQ #

S_P WRD WN #

FRA M E

LAD 1

LAD 2

SMB _CL K_M AIN

SMB _DA TA_ MAI N

module TPM (Trusted Platform

PC ICL K

Module – Module de plateforme

sécurisée), qui permet de sauve-

GN D

garder clés, certicats numériques, mots de passe et données en toute sécurité. Le système TPM permet également de renforcer la sécurité du réseau, de protéger les identités numériques et de préserver l’intégrité de la plateforme.

Fatal1ty E3V5 Performance Gaming/OC Series

Connecteur d’alimentation PCIe (PCIE_PWR1 à 4 broches) (voir p.1, No. 23)

GND

+12V DETECT

Veuillez connecter un câble

d’alimentation molex à 4broches

à ce connecteur lorsque plus

de trois cartes graphiques sont

installées.

Français

1 Introduzione

Grazie per aver acquistato la scheda madre ASRock Fatal1ty E3V5 Performance Gaming/OC Series, una scheda madre adabile prodotta secondo i severissimi controlli di qualità ASRock. La scheda madre ore eccellenti prestazioni con un design robusto che si adatta all'impegno di ASRock di orire sempre qualità e durata.

Dato che le speciche della scheda madre e del soware BIOS possono essere aggiornate, il contenuto di questa documentazione sarà soggetto a variazioni senza preavviso. Nel caso di eventuali modiche della presente documentazione, la versione aggiornata sarà disponibile sul sito Web di ASRock senza ulteriore preavviso. Per il supporto tecnico correlato a questa scheda madre, visitare il nostro sito Web per informazioni speciche relative al modello attualmente in uso. È possibile trovare l'elenco di schede VGA più recenti e di supporto di CPU anche sul sito Web di ASRock. Sito Web di ASRock http://www.asrock.com.

1.1 Contenuto della confezione

•Scheda madre ASRock Fatal1ty E3V5 Performance Gaming/OC Series (Form Factor

AT X)

•Guida all'installazione rapida di ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•CD di supporto ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•2 x cavo dati Serial ATA (SATA) (opzionali)

•1 x mascherina metallica posteriore I/O

Italiano

1.2 Speciche

Fatal1ty E3V5 Performance Gaming/OC Series

Piattaforma

CPU

Chipset

Memoria

Alloggio d’espansione

•Fattore di forma ATX

•Supporta processori Intel® Xeon® E3-1200 v5 e processori

6th Generation Intel® CoreTM i3/Pentium®/Celeron® (Socket

1151)

•Design Digi Power

•Potenza a 10 fasi

•Supporta la tecnologia Intel® Turbo Boost 2.0

•Supporto di CPU unlocked Intel® K-Series

•Supporta gamma completa overclocking BCLK ASRock

•Intel® C232

•Tecnologia memoria DDR4 Dual Channel

•4 alloggi DIMM DDR4

•Supporto di memoria DDR4 2133 non-ECC, un-buered

•Supporto di moduli di memoria ECC UDIMM

•Capacità max. della memoria di sistema: 64GB

•Supporto di XMP (Extreme Memory Prole) Intel® 2.0

•Contatti d’oro 15μ negli alloggi DIMM

•2 x Alloggi PCI Express 3.0 x16 (PCIE2: Modalità

x16:PCIE4:modalità x4)* * Supporto di SSD NVMe come disco d’avvio

•3 alloggi PCI Express 3.0 x1 (PCIe essibile)

•Supporta AMD Quad CrossFireX

•Contatti d’oro 15μ nell’alloggio VGA PCIe (PCIE2)

e CrossFireXTM

Audio

Italiano

•Audio HD a 7.1 canali con Content Protection (codec audio

Realtek ALC1150)

•Supporto audio Blu-ray Premium

•Supporto protezione da sovratensione (protezione completa

ASRock dai picchi di corrente)

•Supporto di Purity Sound

- Cappucci audio Nichicon serie Fine Gold

- 115dB SNR DAC con amplicatore dierenziale

- Amplicatore cue TI® NE5532 Premium (supporta cue no a 600 Ohm)

- Pura potenza

- Tecnologia Direct Drive

- Schermatura isolata PCB

•Supporta DTS Connect

Italiano

LAN

I/O pannello posteriore

•LAN Gigabit 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•Supporta Wake-On-LAN

•Supporto la protezione da fulmini/scariche elettrostatiche

(ESD) (protezione completa ASRock dai picchi di corrente)

•Supporta Energy Ecient Ethernet 802.3az

•Supporta PXE

•1 x porta mouse/tastiera PS/2

•1 x porta uscita SPDIF ottico

•1 x Porta USB 2.0 (supporto protezione da scariche

elettrostatiche (ESD) (protezione completa ASRock dai picchi di corrente))

•1 x Porta mouse Fatal1ty (USB 2.0) (supporto protezione da

scariche elettrostatiche (ESD) (protezione completa ASRock dai picchi di corrente))

•4 x Porte USB 3.0 (supporto protezione da scariche

elettrostatiche (ESD) (protezione completa ASRock dai picchi di corrente))

•1 x porta LAN RJ-45 con LED (ACT/LINK LED e SPEED

LED)

•Connettori audio HD: altoparlante posteriore/centrale/

basso/ingresso linea/altoparlante anteriore/microfono

Archiviazione

•6 x connettori SATA3 6,0 Gb/s, supportano RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel RSTe), NCQ, AHCI e Hot Plug

Fatal1ty E3V5 Performance Gaming/OC Series

Connettore

Funzionalità BIOS

•1 collettore porta COM

•1 x Collettore TMP

•1 x Connettore LED alimentazione e altoparlante

•2 x Connettori ventola CPU (4 pin) (Smart Fan Speed

Control)

•4 x Connettori ventola telaio (4 pin) (Smart Fan Speed

Control)

•1 connettore alimentazione ATX 24 pin

•1 x Connettore alimentazione 12V 8-pin

•1 x Connettore alimentazione PCIe

•1 connettore audio pannello frontale

•2 x Collettori USB 2.0 (supporto di 4 porte USB 2.0)

(supporto protezione da scariche elettrostatiche (ESD) (protezione completa ASRock dai picchi di corrente))

•1 x Collettore USB 3.0 (supporta 2 porte USB 3.0) (supporto

protezione da scariche elettrostatiche (ESD) (protezione completa ASRock dai picchi di corrente))

•AMI UEFI Legal BIOS con interfaccia di supporto multi-

lingue

•Eventi di riattivazione conformi a ACPI 5.0

•Supporto SMBIOS 2.7

•Regolazione multipla tensione CPU, GT_CPU, DRAM,

VPPM, PCH 1.0V, VCCIO, VCCPLL, VCCSA

HardwareMonitor

•Rilevamento temperatura CPU/telaio

•Tachimetro ventola CPU/telaio

•Ventola silenziosa CPU/telaio (regolazione automatica

velocità in base alla temperatura della CPU)

•Ventola CPU/chassis con controllo di varie velocità

•Monitoraggio tensione: +12V, +5V, +3,3V, CPU Vcore, GT_

CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VCCSA

Italiano

•Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-

bit * Per installare Windows® 7, è necessario un disco di installazione modicato con i driver xHCI integrati nel le ISO. Fare riferimento a pagina 146 per altre istruzioni dettagliate. * Per il driver aggiornato di Windows® 10, visitare il sito ASRock all’indirizzo: http://www.asrock.com.

Italiano

Certicazioni

•FCC, CE, WHQL

•ErP/EuP Ready (è necessaria alimentazione ErP/EuP ready)

* Per informazioni dettagliate sul prodotto, visitare il nostro sito Web: http://www.asrock.com

Prestare attenzione al potenziale rischio previsto nella pratica di overclocking, inclusa la regolazione delle impostazioni nel BIOS, l'applicazione di tecnologia di Untied Overclocking o l'utilizzo di strumenti di overclocking di terze parti. L'overclocking può inuenzare la stabilità del sistema o perno provocare danni ai componenti e ai dispositivi del sistema. Occorre eseguirlo a proprio rischio e spese. Non ci riterremo responsabili per possibili danni provocati da overclocking.

Fatal1ty E3V5 Performance Gaming/OC Series

1.3 Impostazione jumper

L'illustrazione mostra in che modo vengono impostati i jumper. Quando il cappuccio del jumper è posizionato sui pin, il jumper è "cortocircuitato". Se sui pin non è posizionato alcun cappuccio del jumper, il jumper è "aperto". L'illustrazione mostra un jumper a 3 pin i cui pin1 e pin2 sono "cortocircuitati" quando un cappuccio del jumper è posizionato su questi 2 pin.

Jumper per azzerare la CMOS (CLRMOS1) (vedere pag. 1, n. 15)

CLRMOS1 permette si azzerare i dati nella CMOS. Per azzerare e reimpostare i parametri del sistema alla congurazione predenita, spegnere il computer e scollegare il cavo di alimentazione dalla rete. Attendere 15 secondi, quindi usare un cappuccio jumper per cortocircuitare il pin 2 ed il pin 3 su CLRMOS1 per 5 secondi. Tuttavia, non azzerare la CMOS subito dopo aver aggiornato il BIOS. Se è necessario azzerare la CMOS dopo l'aggiornamento del BIOS, è necessario riavviare prima il sistema e in seguito spegnerlo prima di eseguire l'operazione di azzeramento della CMOS. La password, la data, l'ora e il prolo predenito dell'utente saranno azzerati solo se viene rimossa la batteria della CMOS.

Azzerare la CMOSpredenito

Italiano

1.4 Header e connettori sulla scheda

Gli header e i connettori sulla scheda NON sono jumper. NON posizionare cappucci del jumper su questi header e connettori. Il posizionamento di cappucci del jumper su header e connettori provocherà danni permanenti alla scheda madre.

Italiano

Header sul pannello del sistema (PANEL1 a 9 pin) (vedere pag. 1, n. 14)

PWRBTN (interruttore di alimentazione):

collegare all'interruttore dell'alimentazione sul pannello anteriore dello chassis. È possibile congurare il modo in cui spegnere il sistema utilizzando l'interruttore dell'alimentazione.

RESET (interruttore di reset):

collegare all'interruttore di reset sul pannello anteriore dello chassis. Premere l'interruttore di reset per riavviare il computer se il computer si blocca e non riesce ad eseguire un normale riavvio.

PLED (LED alimentazione del sistema):

collegare all'indicatore di stato dell'alimentazione sul pannello anteriore dello chassis. Il LED è acceso quando il sistema è in funzione. Il LED continua a lampeggiare quando il sistema si trova nello stato di sospensione S1/S3. Il LED è spento quando il sistema si trova nello stato di sospensione S4 o quando è spento (S5).

HDLED (LED di attività disco rigido):

collegare al LED di attività disco rigido sul pannello anteriore dello chassis. Il LED è acceso quando il disco rigido sta leggendo o scrivendo dati.

Il design del pannello anteriore può cambiare a seconda dello chassis. Un modulo di pannello anteriore è composto principalmente da interruttore di alimentazione, interruttore di reset, LED di alimentazione, LED di attività disco rigido, altoparlante, ecc. Quando si collega il modulo del pannello anteriore dello chassis a questo header, accertarsi che le assegnazioni del lo e le assegnazioni del pin corrispondano correttamente.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Collegare l'interruttore dell'alimentazione, l'interruttore di reset e l'indicatore dello stato del sistema sullo chassis su questo header secondo la seguente assegnazione dei pin. Annotare i pin positivi e negativi prima di collegare i cavi.

Fatal1ty E3V5 Performance Gaming/OC Series

PLED-

SPEAKER

Connettore LED alimentazione e altoparlante (SPK_PLED1 7 pin) (vedere pag. 1, n. 16)

Connettori Serial ATA3 (SATA3_0_1: vedere pag. 1, n. 8) (SATA3_2_4: vedere pag. nr. 11) (SATA3_3_5: vedere pag.1, n. 10)

Header USB 2.0 (USB1_2 9 pin (vedere pag. 1, n. 17) (9-pin USB3_4) (vedere pag. 1, n. 18)

DUMMY +5V

PLED+

SATA3_1

SATA3_5

SATA3_3

USB_PWR

-B

-A

USB_PWR

DUMMY

PLED+

SATA3_4

SATA3_2

GND

DUMMY

Collegare i LED alimentazione e l’altoparlante a questo connettore.

Questi sei connettori SATA3 supportano cavi dati SATA per dispositivi

SATA3_0

di archiviazione interna, con una velocità di trasferimento dati no a 6,0 Gb/s.

Ci sono due connettori su questa scheda madre. Ciascun header USB 2.0 può supportare due porte.

Header USB 3.0 (USB3_7_8 19 pin) (vedere pag. 1, n. 7)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Oltre alle quattro porte USB 3.0 del pannello I/ O, questa scheda madre è dotata di un collettore. Ciascun header USB 3.0 può supportare due porte.

Italiano

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

Questo header serve a collegare i dispositivi audio al pannello audio anteriore.

Header audio pannello anteriore (AUDIO1_HD a 9 pin) (vedere pag. 1, n. 22)

1. L'audio ad alta denizione supporta le funzioni Jack sensing, ma il lo del pannello sullo chassis deve supportare HDA per funzionare correttamente. Seguire le istruzioni presenti nel nostro manuale e nel manuale dello chassis per installare il sistema.

2. Se si utilizza un pannello audio AC’97, installarlo sull'header audio del pannello anteriore seguendo le fasi di seguito: A. Collegare Mic_IN (MIC) a MIC2_L. B. Collegare Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L. C. Collegare Ground (GND) a Ground (GND). D. MIC_RET e OUT_RET servono soltanto per il pannello audio HD. Non è necessario collegarli per il pannello audio AC’97. Per attivare il microfono anteriore, andare alla scheda “FrontMic” nel pannello di controllo Realtek e regolare il “Volume di registrazione”.

Italiano

Connettori ventola telaio (CHA_FAN1 a 4 pin) (vedere pag. 1, n. 13) (CHA_FAN2 a 4 pin) (vedere pag. 1, n. 12) (CHA_FAN3 a 4 pin) (vedere pag. 1, n. 19)

(CHA_FAN4 a 4 pin) (vedere pag. 1, n. 6)

Connettori della ventola della CPU (CPU_FAN1 a 4 pin) (vedere pag. 1, n. 4)

(CPU_FAN2 a 4 pin) (vedere pag. 1, n. 9)

GND

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

FAN_VOLTAGE

CPU_FAN_SPEED

GND

FAN_SPEED_CONTROL

1 2 3 4

GND

FAN_VOLTAGE CPU_FAN_SPEED

FAN_SPEED_CONTROL

Collegare i cavi della ventola ai connettori della ventola e far corrispondere il lo nero al pin di terra.

Questa scheda madre fornisce due connettori ventola CPU a 4 pin (Quiet Fan). Se si decide di collegare una ventola della CPU a 3 pin, collegarla al pin 1-3.

Fatal1ty E3V5 Performance Gaming/OC Series

Connettore di alimentazione ATX (ATXPWR1 a 24 pin) (vedere pag. 1, n. 5)

Connettore di alimentazione ATX da 12 V (ATX12V1 a 8 pin) (vedere pag. 1, n. 1)

Header porta seriale (COM1 a 9 pin) (vedere pag. 1, n. 21)

Header TPM (TPMS1 a 17 pin) (vedere pag. 1, n. 20)

Questa scheda madre è dotata di un connettore di alimentazione ATX a 24 pin. Per utilizzare un'alimentazione ATX a 20 pin, collegarla lungo il

pin1 e il pin 13.

Questa scheda madre è dotata di un connettore di alimentazione ATX da 12 V a 8 pin. Per utilizzare un'alimentazione ATX a 4 pin, collegarla lungo il pin1 e il pin 5.

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Questo header COM1 supporta un modulo di porta seriale.

Questo connettore supporta il

GN D

LAD 0

+3 V

+3V S B

GN D

LAD 1

SER IRQ #

S_P WRD WN #

PC ICL K

LAD 3

PC IRS T #

FRA M E

LAD 2

sistema Trusted Platform Module

(TPM), che può archiviare in modo sicuro chiavi, certicati

GN D

digitali, password e dati. Un sistema TPM permette anche di

SMB _CL K_M AIN

SMB _DA TA_ MAI N

potenziare la sicurezza della rete, di proteggere identità digitali

Italiano

e di garantire l'integrità della piattaforma.

Connettore alimentazione PCIe (4-pin PCIE_PWR1) (vedere pag. 1, n. 23)

GND

+12V DETECT

Collegare un cavo di alimentazione molex a 4 pin a questo connettore quando sono installate più di tre schede grache.

Italiano

Fatal1ty E3V5 Performance Gaming/OC Series

1 Introducción

Gracias por comprar la placa base ASRock Fatal1ty E3V5 Performance Gaming/OC Series, una placa base able fabricada según el rigurosísimo control de calidad de ASRock. Ofrece un rendimiento excelente con un diseño resistente de acuerdo con el compromiso de calidad y resistencia de ASRock.

Ya que las especicaciones de la placa base y el soware del BIOS podrán ser actualizados, el contenido que aparece en esta documentación estará sujeto a modicaciones sin previo aviso. Si esta documentación sufre alguna modicación, la versión actualizada estará disponible en el sitio web de ASRock sin previo aviso. Si necesita asistencia técnica relacionada con esta placa base, visite nuestro sitio web para obtener información especíca sobre el modelo que esté utilizando. Podrá encontrar las últimas tarjetas VGA, así como la lista de compatibilidad de la CPU, en el sitio web de ASRock. Sitio web de ASRock http://www.asrock.com.

1.1 Contenido del paquete

•Placa base ASRock Fatal1ty E3V5 Performance Gaming/OC Series (Factor de forma

AT X)

•Guía de instalación rápida de ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•CD de soporte de ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•2 x Cables de datos Serial ATA (SATA) (Opcional)

•1 x escudo panel I/O

Español

1.2 Especicaciones

Español

Plataforma

CPU

Conjunto de chips

Memoria

Ranura de expansión

•Factor de forma ATX

•Admite la procesadores Intel® Xeon® E3-1200 v5 y la familia

de procesadores Intel® CoreTM i3/Pentium®/Celeron® (zócalo

1151) de la 6ª generación

•Diseño Digi Power

•Diseño de fase de alimentación 10

•Compatible con la tecnología de Intel® Turbo Boost 2.0

•Compatible con overclocking de rango completo BCLK de

ASRock

•Admite motor hiper-BCLK de ASRock

•Intel® C232

•Tecnología de memoria DDR4 de doble canal

•4 x Ranuras DIMM DDR4

•Admite memoria sin búfer DDR4 2133 no ECC

•Admite módulos de memoria UDIMM ECC

•Capacidad máxima de la memoria del sistema: 64GB

•Admite Perl de memoria extremo de Intel® (XMP) 2.0

•Contacto 15μ Gold en ranuras DIMM

•2 x Ranuras PCI Express 3.0 x16 (PCIE2:modo x16;

PCIE4:modo x4)

•3 ranuras PCI Express 3.0 x1 (PCIe exible)

•Compatible con AMD Quad CrossFireX

•Contacto 15μGold en ranura VGA PCIe (PCIE2)

y CrossFireXTM

Audio

•7.1 Audio CH HD con Protección de contenido (Realtek

ALC1150 Audio Codec)

•Compatible con audio Blu-ray Premium

•Compatible con protección por sobretensión (protección

ASRock Full Spike)

Fatal1ty E3V5 Performance Gaming/OC Series

LAN

Panel trasero I/O

•Compatible con Purity Sound

- Tapas de audio Nichion de la serie Fine Gold

- 115dB SNR DAC con amplicador diferencial

- Amplicador de auriculares de alta calidad TI® NE5532 (admite auriculares de hasta 600 ohmios)

- Entrada de alimentación pura

- Tecnología Direct Drive

- Protección de aislamiento PCB (circuito impreso)

•Compatible con DTS Connect

•LAN Gigabit 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•Compatible con Wake-On-LAN

•Compatible con protección contra rayos y electricidad

electrostática (protección ASRock Full Spike)

•Compatible con Ethernet de consumo eciente de energía

802.3az

•Compatible con PXE

•1 x puerto de ratón/teclado PS/2

•1 x puerto de salida SPDIF óptica

•1 x puerto USB 2.0 (compatible con protección contra

electricidad estática (protección ASRock Full Spike))

•1 x puerto de ratón Fatal1ty (USB 2.0) (compatible con

protección contra electricidad estática (protección ASRock Full Spike))

•4 puertos USB 3.0 (compatible con protección contra

electricidad estática (protección ASRock Full Spike))

•1 x puerto LAN RJ-45 con LED (ACT/LINK LED y SPEED

LED)

•Conector de audio HD: Altavoz trasero / Central / Graves /

Entrada de línea / Altavoz frontal / Micrófono

Español

Almacenamiento

•6 x Conectores SATA3 de 6,0 Gb/s, compatibilidad con RAID

(RAID 0, RAID 1, RAID 5, RAID 10, Intel RSTe), NCQ, AHCI y conexión en caliente

Conector

•1 x Cabezal de puerto COM

•1 x cabezal TPM

•1 x LED de alimentación y base de conexiones para el altavoz

•2 x Conectores (4 contactos) para el ventilador de la CPU

(control de velocidad de ventilador inteligente)

•4 x Conectores (4 contactos) para el ventilador del chasis (con-

trol de velocidad de ventilador inteligente)

•1 Conector de alimentación ATX de 24 pines

•1 Conector de alimentación de 8 pines y 12V

•1 conector de alimentación PCIe

•1 Conector de audio del panel frontal

•2 cabezales USB 2.0 (compatible con 4 puertos USB 2.0)

(compatible con protección contra electricidad estática (protección ASRock Full Spike))

•1 cabezal USB 3.0 (compatible con 2 puertos USB 3.0)

(compatible con protección contra electricidad estática (protección ASRock Full Spike))

Español

Función del BIOS

Monitor del hardware

•BIOS legal UEFI AMI compatible con interfaz gráca de usu-

ario multilingüe

•Eventos de reactivación conformes con ACPI 5.0

•Compatible con SMBIOS 2.7

•Varios ajustes de voltaje de CPU, GT_CPU, DRAM, VPPM,

PCH 1,0V, VCCIO, VCCPLL y VCCSA

•Método de sensor de temperatura de la CPU/Chasis

•Tacómetro del ventilador de la CPU/Chasis

•CPU/Chasis Ventilador silencioso (Ajuste automático de

velocidad del ventilador del chasis por temperatura de la CPU)

•Control multivelocidad del ventilador de la CPU/Chasis

•Control de voltaje: +12 V, +5 V, +3,3 V, Vcore de CPU, GT_

CPU, DRAM, VPPM, PCH 1,0 V, VCCIO y VCCSA

•Microso® Windows® 10 de 64 bits, 8.1 de 64 bits, 7 de 32 bits y

7 de 64 bits * Para instalar el sistema operativo Windows® 7, se necesita un disco de instalación modicado con los controladores xHCI empaquetados en el archivo ISO. Consulte la página 146 para obtener información más detallada.

Fatal1ty E3V5 Performance Gaming/OC Series

* Para obtener el controlador actualizado para Windows® 10, visite el sitio Web desde ASRock para obtener detalles: http://www.asrock.com.

Certicaciones

•FCC, CE, WHQL

•Compatible con ErP/EuP (requiere toma de alimentación

compatible con ErP/EuP)

* Para obtener más información acerca del producto, visite nuestro sitio web: http://www.asrock.com

Tenga en cuenta que existen ciertos riesgos relacionados con el overclocking (sobreaceleración), incluyendo el ajuste de la conguración del BIOS, aplicando la Tecnología overcloking no vinculada o utilizando las herramientas de overclocking de tercera parte. El overclocking podría afectar la estabilidad de su sistema o incluso dañar los componentes y dispositivos de su sistema. Si lo realiza, todos los riesgos y gastos derivados del overclocking serán de su entera responsabilidad. No nos hacemos responsables de posibles daños producidos por el overclocking.

Español

1.3 Instalación de los puentes

La instalación muestra cómo deben instalarse los puentes. Cuando la tapa de puente se coloca en los pines, el puente queda “Corto”. Si no coloca la tapa de puente en los pines, el puente queda “Abierto”. La ilustración muestra un puente de 3 pines cuyo pin 1 y pin 2 son “Cortos” cuando se coloca una tapa de puente en estos 2 pines.

Puente de borrado de CMOS (CLRMOS1) (consulte la pág.1, N.º 15)

CLRMOS1 le permite borrar los datos del CMOS. Para borrar y restablecer los parámetros del sistema a los valores predeterminados de instalación, apague el ordenador y desenchufe el cable de alimentación de la toma de alimentación. Después de esperar 15 segundos, utilice un tapa de puente para acortar el pin2 y el pin3 en el CLRMOS1 durante 5 segundos. Sin embargo, no borre el CMOS justo después de que haya actualizado el BIOS. Si necesita borrar el CMOS cuando acabe de actualizar el BIOS, deberá arrancar el sistema primero y, a continuación, deberá apagarlo antes de que realice el borrado del CMOS. Tenga en cuenta que la contraseña, la fecha, la hora y el perl de usuario predeterminado serán eliminados únicamente si se retira la pila del CMOS.

Borrado de CMOSPredeterminado

Fatal1ty E3V5 Performance Gaming/OC Series

1.4 Conectores y cabezales incorporados

Los cabezales y conectores incorporados NO son puentes. NO coloque tapas de puente sobre estos cabezales y conectores. Si coloca tapas de puente sobre los cabezales y conectores dañará de forma permanente la placa base.

Cabezal del panel del sistema (PANEL1 de 9 pines) (consulte la pág.1, N.º 14)

PWRBTN (Interruptor de alimentación):

Conéctelo al interruptor de alimentación del panel frontal del chasis. Deberá congurar la forma en la que su sistema se apagará mediante el interruptor de alimentación.

RESET (Interruptor de reseteo):

Conéctelo al interruptor de reseteo del panel frontal del chasis. Pulse el interruptor de reseteo para resetear el ordenador si éste está bloqueado y no se puede reiniciar de forma normal.

PLED (Indicador LED de la alimentación del sistema):

Conéctelo al indicador de estado de la alimentación del panel frontal del chasis. El indicador LED permanece encendido cuando el sistema está funcionando. El indicador LED parpadea cuando el sistema se encuentra en estado de suspensión S1/S3. El indicador LED se apaga cuando el sistema se encuentra en estado de suspensión S4 o está apagado (S5).

HDLED (Indicador LED de actividad en el disco duro):

Conéctelo al indicador LED de actividad en el disco duro del panel frontal del chasis. El indicador LED permanece encendido cuando el disco duro está leyendo o escribiendo datos.

El diseño del panel frontal puede ser diferente dependiendo del chasis. Un módulo de panel frontal consta principalmente de: interruptor de alimentación, interruptor de reseteo, indicador LED de alimentación, indicador LED de actividad en el disco duro, altavoz, etc. Cuando conecte su módulo del panel frontal del chasis a este cabezal, asegúrese de que las asignaciones de los cables y los pines coinciden correctamente.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Conecte el interruptor de alimentación, restablezca el interruptor y el indicador del estado del sistema del chasis a los valores de este cabezal, según los valores asignados a los pines como se indica a continuación. Cerciórese de cuáles son los pines positivos y los negativos antes de conectar los cables.

Español

LED de alimentación y

PLED-

SPEAKER

base de conexiones para la altavoz (SPK_PLED1 de 7 contactos) (consulte la pág.1, N.º 17)

DUMMY +5V

PLED+

DUMMY

PLED+

Conecte el LED de alimentación del chasis y el altavoz del chasis a esta base de conexiones.

Español

Conectores Serie ATA3 (SATA3_0_1: consulte la pág.1, N.º 8) (SATA3_2_4: consulte la pág. 1, Nº 11) (SATA3_3_5: consulte la pág.1, N.º 10)

Cabezales USB 2.0 (USB1_2 de 9 contactos) (consulte la pág.1, N.º 17) (USB3_4 de 9 pines) (consulte la pág.1, N.º 18)

Cabezal USB 3.0 (USB3_7_8 de 19 contactos) (consulte la pág.1, N.º 7)

SATA3_5

SATA3_3

USB_PWR

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

SATA3_1

-B

-A

GND

SATA3_4

SATA3_2

DUMMY

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Estos seis conectores SATA3 son compatibles con cables de datos SATA

SATA3_0

para dispositivos de almacenamiento interno con una velocidad de transferencia de datos de hasta 6,0 Gb/s.

Hay dos bases de conexiones en esta placa base. Cada cabezal USB 2.0 admite dos puertos.

Además de cuatro puertos USB 3.0 en el panel I/O, esta placa base contiene un cabezal. Cada cabezal USB

3.0 admite dos puertos.

Fatal1ty E3V5 Performance Gaming/OC Series

Cabezal de audio del panel frontal (HD_AUDIO1 de 9 pines) (consulte la pág.1, N.º 22)

1. El Audio de Alta Denición (HDA, en inglés) es compatible con el método de sensor de conectores, sin embargo, el cable del panel del chasis deberá ser compatible con HDA para que pueda funcionar correctamente. Siga las instrucciones que se indican en nuestro manual y en el manual del chasis para instalar su sistema.

2. Si utiliza un panel de audio AC’97, colóquelo en el cabezal de audio del panel frontal siguiendo los pasos que se describen a continuación: A. Conecte Mic_IN (MIC) a MIC2_L. B. Conecte Audio_R (RIN) a OUT2_R y Audio_L (LIN) a OUT2_L. C. Conecte Ground (Conexión a tierra) (GND) a Ground (GND). D. MIC_RET y OUT_RET se utilizan únicamente con el panel de audio HD. No es necesario que los conecte en el panel de audio AC’97. E. Para activar el micrófono frontal, vaya a la cha “micrófono frontal” (FrontMic) en el panel de control de Realtek y ajuste el “Volumen de grabación” (Recording Volume).

Conectores para el ventilador del chasis (CHA_FAN1 de 4 pines) (consulte la pág.1, N.º 13) (CHA_FAN2 de 4 pines) (consulte la pág.1, N.º 12)

GND

PRESENCE#

MIC_RET

OUT_RET

FAN_SPEED

FAN_SPEED_CONTROL

J_SENSE

OUT2_R

MIC2_R

MIC2_L

GND

FAN_VOLTAGE

OUT2_L

Este cabezal se utiliza para conectar dispositivos de audio al panel de audio frontal.

Conecte los cables del ventilador a los conectores del ventilador y haga coincidir el cable negro con el pin de conexión a

tierra. (CHA_FAN3 de 4 pines) (consulte la pág.1, N.º 19)

(CHA_FAN4 de 4 pines) (consulte la pág.1, N.º 6)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

Español

Conectores del ventilador de la CPU (CPU_FAN1 de 4 pines) (consulte la pág.1, N.º 4)

(CPU_FAN2 de 4 pines) (consulte la pág.1, N.º 9)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND

FAN_VOLTAGE

CPU_FAN_SPEED

FAN_SPEED_CONTROL

Esta placa base contiene

dos conectores de

ventilador (ventilador

silencioso) de CPU de

4 contactos. Si tiene

pensando conectar un

ventilador de CPU de 3

pines, conéctelo al Pin 1-3.

Conector de alimentación

AT X (ATXPWR1 de 24 pines) (consulte la pág.1, N.º 5)

Esta placa base contiene un conector de alimentación ATX de 24 pines. Para utilizar una toma de alimentación ATX de 20 pines, conéctela en los

Pines del 1 al 13.

Español

Conector de alimentación ATX de 12V (ATX12V1 de 8 pines) (consulte la pág.1, N.º 1)

Cabezal de puerto serie (COM1 de 9 pines) (consulte la pág.1, N.º 21)

Cabezal TPM (TPMS1 de 17 pines) (consulte la pág.1, N.º 20)

Esta placa base contiene un conector de alimentación ATX de 12V y 8 pines. Para utilizar una toma de alimentación ATX de 4 pines, conéctela en los Pines del 1 al 5.

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Este cabezal COM1 admite un módulo de puerto serie.

Este conector es compatible con

GN D

LAD 0

+3 V

+3V S B

GN D

LAD 1

SER IRQ #

S_P WRD WN #

PC ICL K

LAD 3

PC IRS T #

FRA M E

el sistema Módulo de Plataforma

Segura (TPM, en inglés), que puede almacenar de forma segura

GN D

LAD 2

claves, certicados digitales, contraseñas y datos. Un sistema

SMB _CL K_M AIN

SMB _DA TA_ MAI N

TPM también ayuda a aumentar la seguridad en la red, protege las identidades digitales y garantiza la integridad de la plataforma.

Conector de alimentación PCIe (PCIE_PWR1 de 4 pines) (consulte la pág.1, N.º 23)

GND

+12V DETECT

Conecte a este conector un cable de alimentación molex de 4 pines cuando se instalen más de tres tarjetas grácas.

Fatal1ty E3V5 Performance Gaming/OC Series

1 Введение

Благодарим вас за приобретение надежной системной платы ASRock Fatal1ty E3V5 Performance Gaming/OC Series, выпускаемой под постоянным жестким контролем качества компании ASRock. Эта материнская плата обеспечивает великолепную производительность и характеризуется прочной конструкцией в соответствии с требованиями компании ASRock в отношении качества и долговечности.

1.1 Комплект поставки

•Системная плата ASRock Fatal1ty E3V5 Performance Gaming/OC Series (форм-фактор

•Краткое руководство по установке платы ASRock Fatal1ty E3V5 Performance

•Компакт-диск с документацией к плате ASRock Fatal1ty E3V5 Performance Gaming/

•2 х кабеля передачи данных Serial ATA (SATA) (приобретаются отдельно)

•1 х экран панели с портами ввода-вывода

По причине обновления спецификации на материнскую платформу и программного обеспечения BIOS содержимое настоящей документации может быть изменено без предварительного уведомления. При изменении содержимого настоящего документа его обновленная версия будет доступна на веб-сайте ASRock без предварительного уведомления. При необходимости технической поддержки, связанной с материнской платой, посетите веб-сайт и найдите на нем информацию о модели используемой вами материнской платы. На веб-сайте ASRock также можно найти самый последний перечень поддерживаемых VGA-карт и ЦП. Веб-сайт ASRock http://www.asrock.com.

AT X)

Gaming/OC Series

OC Series

Русский

1.2 Спецификация

Русский

Платформа

Процессор

Чипсет

Память

Слот расширения

•Форм-фактор ATX

•Поддержка процессоров Intel® Xeon® E3-1200 v5 и

процессоров 6-го поколения Intel® CoreTM i3/Pentium®/ Celeron® (Socket 1151)

•Digi Power design

•Система питания 10

•Поддержка технологии Intel® Turbo Boost 2.0

•Поддержка полного разгона процессора ASRock BCLK

•Поддерживает систему ASRock Hyper BCLK

•Intel® C232

•Двухканальная память DDR4

•4 гнезда DDR4 DIMM

•Поддержка модулей памяти DDR4 2133 не

относящихся к ECC, небуферизованной памяти

•Поддерживаются модули памяти UDIMM с ECC

•Максимальный объем системной памяти: 64 Гб

•Поддержка Intel® Extreme Memory Prole (XMP)2.0

•Гнезда DIMM с золочеными контактами 15мк

•2 x Слоты PCI Express 3.0 x16 (PCIE2:режим x16;

PCIE4:режим x4)* * Поддерживаются в качестве загрузочных SSD-диски типа NVMe.

•3 x PCI Express 3.0 x1 разъем (Гибкая конфигурация

PCIe)

•Поддержка AMD Quad CrossFireX

•15μ Золоченые контакты разъема VGA PCIe (PCIE2)

и CrossFireXTM

Аудио

•7.1-канальный звук высокой четкости HD Audio с

защитой данных (аудиокодек Realtek ALC1150)

•Поддержка Premium Blu-ray Audio

•Защита от перенапряжения (ASRock Full Spike

Protection)

Fatal1ty E3V5 Performance Gaming/OC Series

LAN

Порты вводавывода на задней панели

•Поддержка Purity Sound

- Конденсаторы для аудиосистем серии Nichicon Fine Gold

- 115 дБ SNR DAC с дифференциальным усилителем

- Усилитель TI® NE5532 Premium Headset Amplier (поддержка гарнитуры с сопротивлением до 600 Ом)

- Стабилизированный вход питания

- Технология Direct Drive

- Изолирующее экранирование печатной платы

•Поддержка DTS-подключения

•Gigabit LAN 10/100/1000 Мб/с

•Giga PHY Intel® I219V

•Поддержка Wake-On-LAN

•Молниезащита и защита электростатического

напряжения (ASRock Full Spike Protection)

•Поддержка Energy Ecient Ethernet 802.3az

•Поддержка PXE

•1 x PS/2 для мыши/клавиатуры

•1 x оптический выходной SPDIF

•1 x Порт USB 2.0 с защитой от электростатического

напряжения (ASRock Full Spike Protection)

•1 x Порт для мыши Fatal1ty (USB 2.0) с защитой от

электростатического напряжения (ASRock Full Spike Protection)

•4 x Порт USB 3.0 с защитой от электростатического

напря- жения (ASRock Full Spike Protection)

•1 x RJ-45 для ЛВС с СИД (СИД ACT/LINK и МИД

SPEED)

•Разъемы HD Audio: задние динамики / центральный

динамик / сабвуфер / линейный вход / передние динамики / микрофон

Русский

Запоминающие устройства

•6 x разъемы SATA3 6,0 Гб/с, поддержка RAID (RAID

0, RAID 1, RAID 5, RAID 10, Intel RSTe), NCQ, AHCI и «горячая» замена

Разъемы

•1 x колодка СОМ-порта

•1 x Колодка ТРМ

•1 x колодка светодиодного индикатора питания и

динамика корпуса

•2 x Разъемы для вентилятора охлаждения процессора

(4-контактный) (“Умный” регулятор скорости вентилятора)

•4 x Разъемы для вентилятора корпуса (4-контактный)

(“Умный” регулятор скорости вентилятора)

•1 х разъем питания АТХ (24-контактный)

•1 х 8-контактный разъем питания 12 В

•1 x Разъем питания PCIe

•1 x аудиоразъем на передней панели

•2 x Колодки USB 2.0 (до 4 портов USB 2.0) с защитой от

электростатического напряжения (ASRock Full Spike Protection)

•1 x Колодка USB 3.0 (до 2 портов USB 3.0) с защитой от

электростатического напряжения (ASRock Full Spike Protection)

Русский

Параметры BIOS

Контроль оборудования

ОС

•AMI UEFI Legal BIOS с поддержкой многоязычного

графического интерфейса

•Совместимость с функцией энергопотребления в

стандарте ACPI 5.0

•Поддержка SMBIOS 2.7

•Регулировка напряжений ЦП, GT_CPU, DRAM, VPPM,

PCH 1.0V, VCCIO, VCCPLL, VCCSA

•Датчик температуры процессора/корпуса

•Тахометр вентилятора процессора/корпуса

•Бесшумный вентилятор охлаждения процессора/

корпуса (с автоматической регулировкой скорости вращения в зависимости от температуры нагрева процессора)

•Управление скоростью вращения вентилятора

охлаждения процессора/корпуса

•Контроль напряжения: +12 В, +5 В, +3,3 В, ЦП Vcore,

GT_CPU, DRAM, VPPM, PCH 1,0 В, VCCIO, VCCSA

•Microso® Windows® 10 64-разрядная / 8.1 64-разрядная

/ 7 32-разрядная / 7 64-разрядная * Для установки ОС Windows® 7 потребуется измененный установочный диск с драйверами xHCI, упакованными в файл ISO. Более подробные инструкции представлены на стр. 146.

Fatal1ty E3V5 Performance Gaming/OC Series

* Подробные сведения об обновлении драйвера Windows® 10 представлены на веб-сайте ASRock: http://www.asrock.com.

Сертификация

•FCC, CE, WHQL

•Совместимость с ErP/EuP (необходим блок питания,

соответствующий стандарту ErP/EuP)

* Для получения дополнительной информации об изделии посетите наш веб-сайт: http://www.asrock.com

Следует учитывать, что разгон процессора, включая изменение настроек BIOS, применение технологии Untied Overclocking Technology и использование инструментов разгона независимых производителей, сопряжен с определенным риском. Разгон процессора может повлиять на стабильность системы или даже привести к повреждению ее компонентов и устройств. Вы выполняете разгон процессора на ваш собственный риск и за свой счет. Мы не несем ответственность за возможный ущерб, вызванный разгоном процессора.

Русский

1.3 Установка перемычек

Установка перемычек показана на рисунке. При установке колпачковой перемычки на контакты перемычка «замкнута». Если колпачковая перемычка на контакты не установлена, перемычка «разомкнута». На рисунке показана 3-контактная перемычка с замкнутыми контактами 1 и 2 при установке на них колпачковой перемычки.

Перемычка сброса настроек CMOS (CLRMOS1) (См. стр. 1, № 15)

CLRMOS1 позволяет очистить данные КМОП. Чтобы сбросить и обнулить параметры системы на настройки по умолчанию, выключите компьютер и извлеките отключите кабель питания от источника питания. Выждите 15 секунд и перемычкой замкните контакты 2 и 3 на CLRMOS1 на 5 секунд. Не сбрасывайте настройки CMOS сразу после обновления BIOS. При необходимости сбросить настройки CMOS сразу после обновления BIOS сначала перезагрузите систему, а затем выключите компьютер перед сбросом настроек CMOS. Учтите, что пароль, дата, время и профиль пользователя по умолчанию сбрасываются только в том случае, если извлечь батарею CMOS.

Сброс настроек CMOSпо умолчанию

Fatal1ty E3V5 Performance Gaming/OC Series

1.4 Колодки и разъемы, расположенные на материнской плате

Расположенные на материнской плате колодки и разъемы перемычками НЕ являются. НЕ устанавливайте на эти колодки и разъемы колпачковые перемычки. Установка колпачковых перемычек на эти колодки и разъемы может вызвать неустранимое повреждение материнской платы.

Колодка системной панели (9-контактная, PANEL1) (См. стр. 1, № 14)

PWRBTN (кнопка питания):

Подключение кнопки питания, расположенной на передней панели корпуса. Можно настроить порядок выключения системы с использованием кнопки питания.

RESET (кнопка перезагрузки):

Подключение кнопки перезагрузки системы, расположенной на передней панели корпуса. Нажмите кнопку перезагрузки, чтобы перезапустить компьютер, если он завис и нормальный запуск невозможен.

PLED (светодиодный индикатор питания системы):

Подключение индикатора состояния, расположенного на передней панели корпуса. Светодиодный индикатор горит, когда система работает. Когда система находится в режиме ожидания S1/S3, светодиод мигает. Когда система находится в режиме ожидания S4 или выключена (S5), светодиод не горит.

HDLED (светодиодный индикатор работы жесткого диска):

Подключение светодиодного индикатора работы жесткого диска, расположенного на передней панели. Светодиодный индикатор горит, когда жесткий диск выполняет считывание или запись данных.

Передняя панель может быть разной на разных корпусах. В основном передняя панель включает в себя кнопку питания, кнопку перезагрузки, светодиодный индикатор питания, светодиодный индикатор работы жесткого диска, динамик и т. д. При подключении передней панели к этой колодке правильно подключайте провода к контактам.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Подключите расположенные на корпусе выключатель питания, кнопку перезагрузки и индикатор состояния системы к этой колодке в соответствии с распределением контактов, приведенным ниже. Перед подключением кабелей определите положительный и отрицательный контакты.

Русский

Колодка светодиодного

PLED-

SPEAKER

индикатора питания и динамика корпуса (7-контактная, SPK_ PLED1) (См. стр. 1, № 16)

DUMMY +5V

PLED+

DUMMY

PLED+

Предназначена для подключения светодиодного индикатора питания и динамика корпуса.

Русский

Разъемы Serial ATA3 (SATA3_0_1: См. стр. 1, № 8) (SATA3_2_4: см. стр. 1, № 11) (SATA3_3_5: см. стр.1, № 10)

Колодки USB 2.0 (9-контактная, USB1_2) (См. стр. 1, № 17) (9-контактная USB3_4) (См. стр. 1, № 18)

Колодка USB 3.0 (19-контактная, USB3_7_8) (См. стр. 1, № 7)

SATA3_5

SATA3_3

USB_PWR

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

SATA3_1

-B

-A

SATA3_4

SATA3_2

GND

DUMMY

GND

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Эти шесть разъемов SATA3 предназначены для подключения кабелей

SATA3_0

SATA внутренних запоминающих устройств для передачи данных со скоростью до 6,0 Гб/с.

На системной плате размещены две колодки. Каждая колодка USB 2.0 может поддерживать два порта.

Кроме четырех портов USB 3.0 на панели вводавывода на материнской плате также есть одна колодка. Каждая колодка USB 3.0 может поддерживать два порта.

Fatal1ty E3V5 Performance Gaming/OC Series

Аудиоколодка передней панели (9-контактная, HD_ AUDIO1) (См. стр. 1, № 22)

1. Аудиосистема высокого разрешения поддерживает функцию распознавания разъема, но для е правильной работы необходимо, чтобы провод панели корпуса поддерживал передачу сигналов HDA. Инструкции по установке системы см. в этом руководстве и руководстве на корпус.

2. При использовании аудиопанели AC’97 подключите ее к аудиоколодке передней панели, как указано далее: A. Подключите Mic_IN (MIC) к MIC2_L. B. Подключите Audio_R (RIN) к OUT2_R, Audio_L (LIN) к OUT2_L. C. Подключите провод заземления (GND) к контакту заземления (GND). D. Контакты MIC_RET и OUT_RET используются только для аудиопанели высокого разрешения. При использовании аудиопанели AC’97 их подключать не нужно. E. Чтобы активировать передний микрофон, перейдите на вкладку FrontMic панели управления Realtek и отрегулируйте параметр Recording Volume (Громкость записи).

Разъемы вентиляторов корпуса (4-контактный, CHA_ FAN1) (См. стр. 1, № 13)

GND

PRESENCE#

MIC_RET

OUT_RET

FAN_SPEED

FAN_SPEED_CONTROL

J_SENSE

OUT2_R

MIC2_R

MIC2_L

GND

FAN_VOLTAGE

OUT2_L

Эта колодка предназначена для подключения аудиоустройств к передней аудиопанели.

Предназначены для подключения кабелей разъемов вентиляторов и подключения черного

провода к заземлению. (4-контактный, CHA_ FAN2) (См. стр. 1, № 12) (4-контактный, CHA_ FAN3) (См. стр. 1, № 19)

Русский

(4-контактный, CHA_ FAN4) (См. стр. 1, № 6)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

Разъемы вентиляторов

ЦП (4-контактный, CPU_ FAN1) (См. стр. 1, № 4)

(4-контактный, CPU_ FAN2) (См. стр. 1, № 9)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND FAN_VOLTAGE CPU_FAN_SPEED

FAN_SPEED_CONTROL

Эта системная плата снабжена двумя 4-контактными разъемами для малошумящего вентилятора ЦП. Если вы собираетесь подключить 3-контактный вентилятор охлаждения процессора, подключайте его к контактам 1-3.

Русский

Разъем питания АТХ (24-контактный, ATXPWR1) (См. стр. 1, № 5)

Разъем питания АТХ 12 В (8-контактный, ATX12V1) (См. стр. 1, № 1)

Колодка последовательного порта (9-контактная, COM1) (См. стр. 1, № 21)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

RRI#1

Эта материнская плата снабжена 24-контактным разъемом питания АТХ. Чтобы использовать 20-контактный разъем питания ATX, подключите его вдоль контакта 1 и контакта 13.

Эта материнская плата снабжена 8-контактным разъемом питания АТХ 12 В. Чтобы использовать 4-контактный разъем питания ATX, подключите его вдоль контакта 1 и контакта 5.

Колодка COM1 поддерживает подключение модуля последовательного порта.

Fatal1ty E3V5 Performance Gaming/OC Series

Колодка ТРМ (17-контактная, TPMS1) (См. стр. 1, № 20)

Разъем питания PCIe (4-контактный PCIE_ PWR1) (См. стр. 1, № 23)

GN D

LAD 0

+3V S B

GN D

SER IRQ #

S_P WRD WN #

+12V DETECT

+3 V

LAD 1

GND

Этот разъем обеспечивает поддержку системы Trusted

PC ICL K

LAD 3

PC IRS T #

FRA M E

Platform Module (TPM), которая

способна обеспечить надежное

GN D

LAD 2

SMB _DA TA_ MAI N

хранение ключей, цифровых сертификатов, паролей и данных. Система ТРМ также

SMB _CL K_M AIN

повышает уровень сетевой безопасности, защищает цифровые идентификаторы и обеспечивает целостность платформы.

При установке более трех графических карт подключите к данному разъему 4-контактный кабель Molex.

Русский

Português

1 Introdução

Obrigado por comprar a placa-mãe ASRock Fatal1ty E3V5 Performance Gaming/ OC Series, uma placa-mãe conável produzida sob o controle de qualidade altamente consistente da ASRock. Esta placa principal oferece um excelente desempenho com um design robusto em conformidade com o compromisso da ASRock em fabricar produtos de qualidade e resistentes.

Como as especicações da placa-mãe e do soware do BIOS podem ser atualizadas, o conteúdo desta documentação estará sujeito a alterações sem aviso prévio. Caso ocorram modicações a esta documentação, a versão atualizada estará disponível no site da ASRock sem aviso prévio. Se precisar de assistência técnica relacionada a esta placa principal, visite o nosso site para obter informações especícas sobre o modelo que estiver utilizando. Você também poderá encontrar a lista de placas VGA e CPU mais recentes suportadas no site da ASRock. Site da ASRock http://www.asrock.com.

1.1 Conteúdo da embalagem

•Placa-mãe ASRock Fatal1ty E3V5 Performance Gaming/OC Series (ATX Form Factor)

•Guia de Instalação Rápida da Placa-mãe ASRock Fatal1ty E3V5 Performance Gaming/

OC Series

•CD de Suporte da Placa-mãe ASRock Fatal1ty E3V5 Performance Gaming/OC Series

•2 x Cabos de dados Serial ATA (SATA) (Opcional)

•1 x Painel de E/S

1.2 Especicações

Fatal1ty E3V5 Performance Gaming/OC Series

Plataforma

CPU

Chipset

Memória

Slot de expansão

•Formato ATX

•Supports Processadores Intel® Xeon® E3-1200 v5 e

Processadores Intel® 6ª Geração CoreTM i3/Pentium®/Celeron® (Soquete 1151)

•Design Digi Power

•Design com 10 fases de alimentação

•Suporta a tecnologia Intel® Turbo Boost 2.0

•Suporta Overclocking total ASRock BCLK

•Suporta Motor ASRock Hyper BCLK

•Intel® C232

•Tecnologia de memória DDR4 de dois canais

•4 x Slots DIMM DDR4

•Suporta memória DDR4 2133, não ECC, sem memória

intermediária

•Suporta módulos de memória ECC UDIMM

•Capacidade máxima da memória do sistema: 64GB

•Suporta Extreme Memory Prole (XMP) 2.0 da Intel®

•Contato em Ouro 15μ nos slots DIMM

•2 x Slots PCI Express 3.0 x16 (PCIE2: modo x16; PCIE4:

modo x4)

•3 x Slots PCI Express 3.0 x1 (Suporta o PCle Flexível com)

•Suporta AMD Quad CrossFireX

•Contato em Ouro 15μ no Slot PCIe VGA (PCIE2)

e CrossFireXTM

Português

Áudio

•Áudio HD de 7.1 canais com proteção de conteúdo (Codec de

áudio Realtek ALC1150)

•Suporte áudio Blu-ray superior

•Suporta proteção contra sobretensão (Proteção Total Contra

Picos ASRock)

•Suporta Purity Sound

- Capacitor de Áudio Série Ouro Fino Nichicon

- 115dB SNR DAC com amplicador diferencial

- Amplicador de Fone de Ouvido TI® NE5532 Premium (suporta fones de ouvido de até 600 Ohms)

- Entrada de Energia Simples

- Tecnologia de drive direto

- Blindagem de isolamento PCB

•Suporta a tecnologia DTS Connect

Português

LAN

E/S do painel posterior

Armazenamento

•LAN Gigabit a 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•Suporta Wake-On-LAN

•Suporta Proteção contra Relâmpago/EDS (Proteção Total

Contra Picos ASRock)

•Suporta Energy Ecient Ethernet 802.3az

•Suporta PXE

•1 x Porta PS/2 para mouse/teclado

•1 x Porta de saída SPDIF ótica

•1 x Porta USB 2.0 (Suporta Proteção ESD (Proteção Total

Contra Picos ASRock))

•1 x Porta de Mouse Fatal1ty (USB 2.0) (Suporta Proteção ESD

(Proteção Total Contra Picos ASRock))

•4 Portas USB 3.0 (Suporta Proteção ESD (Proteção Total

Contra Picos ASRock))

•1 x Porta LAN RJ-45 com LED (LED ACT/LINK e LED DE

VELOCIDADE)

•Fichas de áudio HD: Alto-falante posterior / Central / Graves /

Entrada de linha / Alto-falante frontal / Microfone

•6 x Conectores SATA3 6,0 Gb/s, suporte RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel® RSTe), NCQ, AHCI e Conexão a Quente

Fatal1ty E3V5 Performance Gaming/OC Series

Conector

Funções da BIOS

Monitor de Hardware

•1 suporte porta COM

•1 x Plataforma TPM

•1 x LED de alimentação e Cabeçote de Autofalante

•2 x Conectores de Ventoinha de CPU (4 pinos) (Controle de

Velocidade de Ventoinha Inteligente)

•4 x Conectores de Ventoinha de Chassi (4 pinos) (Controle de

Velocidade de Ventoinha Inteligente)

•1 conector alimentação ATX 24 pinos

•1 x Conector de energia 8-pinos 12V

•1 x Conector de energia PCIe

•1 conector de áudio do painel frontal

•2 x Plataformas USB 2.0 (Suporta 4 portas USB 2.0) (Suporta

Proteção ESD (Proteção Total Contra Picos ASRock))

•1 x Plataforma USB 3.0 (Suporta 2 portas USB 3.0) (Suporta

Proteção ESD (Proteção Total Contra Picos ASRock))

•IAM Legal UEFI BIOS com suporte multilingue GUI

•ACPI 5.0 compatível com eventos de despertar

•Suporta SMBIOS 2.7

•CPU, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VCCPLL,

VCCSA Multi ajuste de tensão

•Sensor de temperatura da CPU/Gabinete

•Tacômetro da Ventoinha da CPU/Gabinete

•Ventoinha silenciosa da CPU/Gabinete (Auto ajusta veloci-

dade da ventoinha do gabinete pela temperatura da CPU)

•Controle de multi velocidade da Ventoinha da CPU/Gabinete

•Monitoramento da tensão: +12V, +5V, +3,3V, CPU Vcore, GT_

CPU, DRAM, VPPM, PCH 1,0V, VCCIO, VCCSA

Português

•Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit

* Para instalar o SO Windows 7, um disco de instalação modicado com condutores xHCI no arquivo ISO é necessário. Consulte a página 146 para a operação mais detalhada. * Para o driver atualizado do Windows® 10, por favor, visite o website da ASRock para mais detalhes:http://www.asrock.com.

Português

Certicações

•FCC, CE, WHQL

•Preparada para ErP/EuP (é necessária uma fonte de

alimentação preparada para ErP/EuP)

* Para obter informações detalhadas sobre o produto, por favor, visite o nosso site: http://www.asrock.com

Por favor, observe que existe um certo risco envolvendo overclocking, incluindo o ajuste das denições na BIOS, a aplicação de tecnologia Untied Overclocking ou a utilização de ferramentas de overclocking de terceiros. O overclocking poderá afetar a estabilidade do sistema ou mesmo causar danos nos componentes e dispositivos do seu sistema. Ele deve ser realizado por sua conta e risco. Não nos responsabilizamos por possíveis danos causados pelo overclocking.

Fatal1ty E3V5 Performance Gaming/OC Series

1.3 Conguração dos jumpers

A imagem abaixo mostra como os jumpers são congurados. Quando a tampa do jumper é colocada nos pinos, o jumper é "Curto". Se não for colocada uma tampa de jumper nos pinos, o jumper é "Aberto". A imagem mostra um jumper de 3 pinos cujos pino1 e pino2 estão "Curtos" quando a tampa do jumper é colocada nestes 2 pinos.

Apagar o Jumper CMOS (CLRMOS1) (ver p.1, N.º 15)

CLRMOS1 permite que você limpe os dados do CMOS. Para apagar e reinicializar os parâmetros do sistema nos valores predenidos, desligue o computador e desplugue a tomada da alimentação. Depois de aguardar 15 segundos, use uma capa de jumper para fazer curto do pino 2 e do pino3 no CLRMOS1 por 5 segundos. No entanto, não apague o CMOS logo após ter realizado a atualização da BIOS. Se você precisar apagar o CMOS logo após ter terminado uma atualização da BIOS, deverá primeiro iniciar o sistema e voltar a encerrá-lo antes de apagar o CMOS. Por favor, observe que a senha, data, hora e perl padrão do usuário serão apagados só se a bateria CMOS for removida.

Apagar CMOSPadrão

Português

1.4 Suportes e conectores onboard

Os conectores e suportes onboard NÃO são jumpers. NÃO coloque tampas de jumpers sobre estes terminais e conectores Colocar tampas de jumpers sobre os terminais e conectores irá causar danos permanentes à placa-mãe.

Português

Suporte do painel de sistema (PAINEL1 de 9 pinos) (ver p.1, N.º 14)

PWRBTN (Botão de alimentação):

Conecte o botão de alimentação no painel frontal do chassi. Você pode congurar a forma para desligar o seu sistema através do botão de alimentação.

RESET (Botão de reinicialização):

Conecte o botão de reinicialização no painel frontal do chassi. Pressione o botão de reinicialização para reiniciar o computador, se ele congela e falha ao realizar um reinício normal.

PLED (LED de alimentação do sistema):

Conecte o indicador do estado da alimentação no painel frontal do chassi. O LED cará aceso quando o sistema estiver em funcionamento. O LED cará piscando quando o sistema estiver nos estados de suspensão S1/S3. O LED cará desligado quando o sistema estiver no estado de suspensão S4 ou desligado (S5).

HDLED (LED de atividade do disco rígido):

Conecte o LED de atividade do disco rígido no painel frontal do chassi. O LED cará aceso quando o disco rígido estiver lendo ou registrando dados.

O design do painel frontal poderá variar dependendo do chassi. Um módulo de painel frontal consiste principalmente em um botão de alimentação, um botão de reinicialização, um LED de alimentação, um LED de atividade do disco rígido, um alto-falante, etc. Ao conectar seu módulo de painel frontal do chassi a este conector, certique-se de que os os e os pinos correspondem de forma correta.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Ligue o botão de alimentação, o botão de reinicialização e o indicador do estado do sistema no chassi deste suporte, de acordo com a descrição abaixo. Observe os pinos positivos e negativos antes de conectar os cabos.

Fatal1ty E3V5 Performance Gaming/OC Series

PLED-

SPEAKER

LED de alimentação e Cabeçote de Autofalante (SPK_PLED1 7 pinos) (ver p.1, N.º 16)

Conectores série ATA3 (SATA3_0_1: ver p.1, N.º 8) (SATA3_2_4: ver p.1, N. 11) (SATA3_3_5: ver p.1, N.º 10)

Suportes USB 2.0 (USB1_2 9pinos (ver p.1, N.º 17) (USB3_4 9-pinos) (ver p.1, N.º 18)

DUMMY +5V

PLED+

SATA3_1

SATA3_5

SATA3_3

USB_PWR

-B

-A

USB_PWR

DUMMY

PLED+

SATA3_4

SATA3_2

GND

DUMMY

Conecte o LED de alimentação do chassi e o autofalante do chassi a este cabeçote.

Estes seis conectores SATA3 suportam cabos de dados SATA

SATA3_0

para dispositivos de armazenamento interno com uma taxa de transferência de dados de até 6,0 Gb/s.

Há dois cabeçotes nesta placa-mãe. Cada suporte USB 2.0 pode suportar duas portas.

Português

Suporte USB 3.0 (USB3_7_8 19 pinos) (ver p.1, N.º 7)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Além das quatro portas USB 3.0 no painel de E/ S, existe um suporte nesta placa principal. Cada suporte USB 3.0 pode suportar duas portas.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

Este suporte destina-se à conexão dos dispositivos de áudio no painel de áudio frontal.

Suporte de áudio do painel frontal (HD_AUDIO1 de 9 pinos) (ver p.1, N.º 24)

1. O Áudio de alta denição suporta Sensor de Adaptador, mas o o do painel no chassi deverá suportar HDA para funcionar corretamente. Por favor, siga as instruções no nosso manual e no manual do chassi para instalar o seu sistema.

2. Se utilizar um painel de áudio AC’97, instale-o no terminal de áudio do painel frontal de acordo com os passos abaixo: A. Ligue Mic_IN (MIC) a MIC2_L. B. Conecte o Audio_R (RIN) a OUT2_R e Audio_L (LIN) a OUT2_L. C. Conecte a ligação Terra (GND) à Terra (GND). D. MIC_RET e OUT_RET destinam-se apenas ao painel de áudio HD. Você não precisa ligá-los ao painel de áudio AC’97. E. Para ativar o microfone frontal, vá à guia “Microfone Frontal” no painel de controle Realtek e ajuste o “Volume de gravação”.

Português

Conectores da Ventoinha do Chassi (CHA_FAN1 de 4 pinos) (ver p.1, N.º 13) (CHA_FAN2 4 pinos) (ver p.1, N.º 12) (CHA_FAN3 de 4 pinos) (ver p.1, N.º 19)

(CHA_FAN4 4 pinos) (ver p.1, N.º 6)

GND

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

Por favor, conecte os cabos do ventilador aos conectores do ventilador e corresponda o o preto no pino terra.

Fatal1ty E3V5 Performance Gaming/OC Series

Conectores do ventilador da CPU (CPU_FAN1 de 4 pinos) (ver p.1, N.º 4)

(CPU_FAN2 de 4 pinos) (ver p.1, N.º 9)

Conector de alimentação AT X (ATXPWR1 de 24 pinos) (ver p.1, N.º 5)

Conector de alimentação de 12V ATX (ATX12V1 de 8 pinos) (ver p.1, N.º 1)

FAN_VOLTAGE

CPU_FAN_SPEED

GND

1 2 3 4

FAN_SPEED_CONTROL

GND

FAN_VOLTAGE

CPU_FAN_SPEED

FAN_SPEED_CONTROL

Esta placa mãe inclui dois conectores de ventilador da CPU (Ventilador silencioso) de 4 pinos. Se você pretende conectar um ventilador da CPU de 3 pinos, por favor, conecte-o ao Pino 1-3.

Esta placa-mãe inclui um conector de alimentação ATX de 24 pinos. Para utilizar uma fonte de alimentação ATX de 20 pinos, introduza-a no Pino 1 e Pino 13.

Esta placa-mãe inclui um conector de alimentação de 12V ATX de 8 pinos. Para utilizar uma fonte de alimentação ATX de 4 pinos, introduza-a no Pino 1 e Pino 5.

Português

Suporte da porta serial (COM1 de 9 pinos) (ver p.1, N.º 21)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

Este suporte COM1 recebe um módulo da porta serial.

RRI#1

Suporte TPM (TPMS1 de 17 pinos) (ver p.1, N.º 20)

Este conector suporta um sistema

GN D

LAD 0

LAD 3

+3 V

PC IRS T #

+3V S B

GN D

SER IRQ #

S_P WRD WN #

FRA M E

LAD 1

LAD 2

SMB _CL K_M AIN

SMB _DA TA_ MAI N

com Módulo de Plataforma

PC ICL K

Conável (TPM), que pode

armazenar com segurança chaves,

GN D

certicados digitais, senhas e dados. Um sistema TPM também ajuda a melhorar a segurança de rede, a proteger identidades digitais e a garantir a integridade da plataforma.

Português

Conector de Energia PCIe (PCIE_PWR1 4-pinos) (ver p.1, N.º 23)

GND

+12V DETECT

Por favor conecte um cabo de alimentação molex de 4 pinos a este conector quando mais de três placas de vídeo estão instaladas.

Fatal1ty E3V5 Performance Gaming/OC Series

1 Giriş

ASRock'ın zorlu kalite kontrol süreçlerinden geçmiş olan ASRock Fatal1ty E3V5 Performance Gaming/OC Series ana kartı satın aldığınız için teşekkür ederiz. Sağlam tasarımı ile ASRock'ın kalite ve dayanıklılık taahhüdüne uygun şekilde mükemmel performans sağlar.

Anakart özellikleri ve BIOS yazılımı güncellenebileceğinden, bu dokümantasyonun içeriği herhangi bir bildirimde bulunulmaksızın değiştirilebilir. Bu dokümantasyon üzerinde herhangi bir değişiklik yapılması halinde, güncellenmiş sürüm, herhangi bir bildirim yapılmaksızın ASRock'ın web sitesinde yer alacaktır.. Bu anakart ile ilgili olarak teknik destek almak istiyorsanız, lütfen kullandığınız model hakkında özel bilgiler için web sitemizi ziyaret edin. En güncel VGA kartları ve CPU destek listelerini de ASRock'ın web sitesinden bulabilirsiniz. ASRock web sitesi http://www.asrock.com.

1.1 Ambalaj İçeriği

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Ana Kart (ATX Form Faktörü)

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Hızlı Kurulum Kılavuzu

•ASRock Fatal1ty E3V5 Performance Gaming/OC Series Destek CD'si

•2 x Seri ATA (SATA) Veri Kablosu (İsteğe Bağlı)

•1 x I/O Panel Kalkanı

Türkçe

1.2 Özellikler

Platform

CPU

Yonga

•ATX Form Faktörü

•Intel® Xeon® E3-1200 v5 İşlemcileri ve 6. Nesil Intel® Core

i3/Pentium®/Celeron® İşlemcileri destekler (Yuva 1151)

•Dijital Güç tasarımı

•10 Güç Fazı tasarımı

•Intel® Turbo Boost 2.0 Teknolojisini destekler

•ASRock BCLK tam aralıklı Hız Aşırtmayı destekler

•ASRock Hyper BCLK Motorunu destekler

•Intel® C232

kümesi

Bellek

Türkçe

Genişletme Yuvası

•Çi Kanallı DDR4 Bellek Teknolojisi

•4 x DDR4 DIMM Yuvası

•DDR4 2133 ECC olmayan, arabelleksiz bellek destekler

•Admite módulos de memoria UDIMM ECC

•Maksimum sistem belleği kapasitesi: 64GB

•Intel® Üstün Bellek Proli (XMP) 2.0 destekler

•DIMM Yuvalarında 15μ Altın Temas

•2 x PCI Express 3.0 x16 Yuva (PCIE2: x16 modu; PCIE4: x4

modu)* * Admite unidad de estado sólido de NVMe como disco de arranque

•3 x PCI Express 3.0 x1 Yuva (Esnek PCIe)

•AMD Quad CrossFireX

•VGA PCIe Yuvasında (PCIE2) 15μ Altın Temas

ve CrossFireXTM desteğine sahiptir

Ses

•İçerik Koruma Özelliği ile 7.1 CH HD Ses (Realtek ALC1150

Ses Codec Bileşeni)

•Üstün Blu-ray Ses desteği

•Dalgalanma Koruması Destekler (ASRock Tam Ani Gerilim

Koruması)

Fatal1ty E3V5 Performance Gaming/OC Series

LAN

Arka Panel I/O

•Purity Sound

- Nichicon Fine Gold Serisi Ses Kapakları

- Fark Yükselteci ile 115dB SNR DAC

- TI® NE5532 Premium Kulaklık Amplikatörü (600 ohm'a kadar kulaklıkları destekler)

- Saf Güç Girişi

- Doğrudan Bağlantı Teknolojisi

- PCB Ayrı Koruma

•DTS Connect işlevini destekler

•Gigabit LAN 10/100/1000 Mb/s

•Giga PHY Intel® I219V

•LAN Açılışını Destekler

•Yıldırım/ESD Koruması Destekler (ASRock Tam Ani Gerilim

Koruması)

•Enerji Verimliliğine Sahip Ethernet 802.3az işlevini destekler

•PXE özelliğini destekler

•1 x PS/2 Fare/Klavye Bağlantı Noktası

•1 x Optik SPDIF Çıkışı Bağlantı Noktası

•1 x USB 2.0 Bağlantı Noktası (ESD Koruması Destekler

(ASRock Tam Ani Gerilim Koruması))

•1 x Fatal1ty Fare Bağlantı Noktası (USB 2.0) (ESD Koruması

Destekler (ASRock Tam Ani Gerilim Koruması))

•4 Bağlayıcısı USB 3.0 Bağlantı Noktası (ESD Koruması

Destekler (ASRock Tam Ani Gerilim Koruması))

•LED'e sahip 1 x RJ-45 LAN Bağlantı Noktası (ACT/LINK LED

ve SPEED LED)

•HD Ses Jakları: Arka Hoparlör / Merkezi / Bas / Hat Girişi /

Ön Hoparlör / Mikrofon

3 destekler

Türkçe

Depolama

•6 x SATA3 6,0 Gb/sn. bağlayıcı, RAID (RAID 0, RAID 1,

RAID 5, RAID 10, Intel RSTe), NCQ, AHCI ve Tak Çıkar destekler

Bağlayıcı

•1 x COM Bağlantı Noktası Bağlantısı

•1 x TPM Bağlantısı

•1 x Güç LED’i ve Hoparlör Bağlantısı

•2 x İşlemci Fanı Bağlayıcısı (4 pimli) (Akıllı Fan Hızı

Kontrolü)

•4 x Kasa Fanı Bağlayıcısı (4 pimli) (Akıllı Fan Hızı Kontrolü)

•1 x 24 pim ATX Güç Bağlayıcısı

•1 x 8 pim 12V Güç Bağlayıcısı

•1 x PCIe Güç Bağlayıcısı

•1 x Ön Panel Ses Bağlayıcısı

•2 x USB 2.0 Bağlantısı (4 USB 2.0 bağlantı noktası destekler)

(ESD Koruması Destekler (ASRock Tam Ani Gerilim Koruması))

•1 x USB 3.0 Bağlantısı (2 USB 3.0 bağlantı noktası destekler)

(ESD Koruması Destekler (ASRock Tam Ani Gerilim Koruması))

Türkçe

BIOS Özelliği

Donanım Monitörü

•Çok dilli GUI Desteği ile AMI UEFI Legal BIOS

•ACPI 5.0 Uyumlu uyandırma olayları

•SMBIOS 2.7 Desteği

•CPU, GT_CPU, DRAM, VPPM, PCH 1.0V, VCCIO, VCCPLL,

VCCSA Çoklu Gerilim Ayarı

•CPU/Kasa sıcaklığı tespiti

•CPU/Kasa Fanı Devirölçer

•İşlemci/Kasa Sessiz Fan (İşlemci sıcaklığıyla otomatik ayarlı

kasa fanı hızı)

•CPU/Kasa Fanı çoklu hız kontrolü

•Voltaj izleme: +12V, +5V, +3,3V, CPU Vcore, GT_CPU,

DRAM, VPPM, PCH 1,0V, VCCIO, VCCSA

•Microso® Windows® 10 64 bit / 8.1 64 bit / 7 32 bit / 7 64 bit

* Windows® 7 işletim sistemini yüklemek için, ISO dosyasında sıkıştırılmış xHCI sürücülerine sahip değiştirilmiş yükleme diski gereklidir. Daha ayrıntılı talimatlar için lütfen 146. sayfaya başvurun. * Güncellenmiş Windows® 10 sürücüsü konusunda ayrıntılar için lütfen ASRock web sitesini ziyaret edin: http://www.asrock.com.

Fatal1ty E3V5 Performance Gaming/OC Series

Belgeler

•FCC, CE, WHQL

•ErP/EuP için hazır (ErP/EuP için hazır güç beslemesi

gereklidir)

* Detaylı ürün bilgisi için, lütfen web sitemizi ziyaret edin: http://www.asrock.com

Lütfen, BIOS ayarlarını düzenleme, Bağımsız Hız Aşırtma Teknolojinin uygulanması ya da üçüncü kişilerin hız aşırtma araçlarının kullanılması da dahil olmak üzere tüm hız aşırtma işlemlerinin belirli bir risk taşıdığını unutmayın. Hız aşırtma, sisteminizin dayanıklılığını etkileyebilir, hatta sisteminizde yer alan bileşen ve aygıtlara zarar verebilir. Bunu riski ve masraarı size ait olmak üzere gerçekleştirilmelidir. Hız aşırtmadan doğabilecek zararlar konusunda sorumlu olmayacağız.

Türkçe

1.3 Bağlantı Teli Kurulumu

Çizim, bağlantı tellerinin kurulumunu göstermektedir. Tel kapağı, pimlerin üzerine yerleştirildiğinde, tel "Kısa" olur. Pimlerin üzerinde tel kapağı bulunmadığında, tel "Açık" olur. Çizim, pin1 ve pin2 alanları "Kısa" olan ve bu iki pim üzerinde bir bağlantı teli kapağı bulunan 3-pin bağlantı telini göstermektedir.

CMOS'u Temizle Bağlantı Te li (CLRMOS1) (bkz. sf.1, No. 15)

CMOS'u TemizleVarsayılan

Türkçe

CLRMOS1, CMOS verilerini temizlememizi sağlar. Sistem parametrelerini temizlemek ve varsayılan kurulum ayarlarına sıfırlamak için, lütfen bilgisayarı kapatın ve güç kablosunu güç beslemesinden çekin. 15 saniye bekledikten sonra, CLRMOS1 üzerindeki pin2 ve pin3'ü 5 saniye boyunca kısaltmak için bir bağlantı teli kullanın. Ancak, CMOS'u lütfen BIOS'u güncelledikten hemen sonra temizlemeyin. +BIOS'u güncelledikten hemen sonra CMOS'u temizlemeniz gerekirse, önce sistemi başlatın ve ardından CMOS temizleme işlemi öncesinde yeniden kapatın. Lütfen, parola, tarih, saat ve varsayılan kullanıcı prolinin yalnızca CMOS bataryası çıkarıldığında temizleneceğini unutmayın.

Fatal1ty E3V5 Performance Gaming/OC Series

1.4 Ekli Bağlantılar ve Bağlayıcılar

Ekli bağlantılar ve bağlayıcılar bağlantı teli değildir. Bağlantı teli kapaklarını bu bağlantı ve bağlayıcılar üzerine yerleştirmeyin. Bağlantı teli kapaklarının bağlantılar ile bağlayıcılar üzerine yerleştirilmesi, anakarta kalıcı hasar verebilir.

Sistem Paneli Bağlantısı (9-pin PANEL1) (bkz sf.1, No. 14)

PWRBTN (Güç Anahtarı):

Güç anahtarını kasa ön paneline bağlayın. Güç anahtarını kullanarak sistemin hangi yöne hareketle kapanacağını seçebilirsiniz.

RESET (Sıfırlama Anahtarı):

Sıfırlama anahtarını kasa ön paneline bağlayın. Bilgisayarın kilitlenmesi ve normal şekilde yeniden başlatılamaması halinde reset (sıfırla) düğmesine basın.

PLED (Sistem Güç LED'i):

Güç durumu göstergesini kasa ön paneline bağlayın. Sistem çalışırken LED ışığı yanacaktır. Sistem S1/S3 uyku durumdayken LED ışığı yanıp söner. Sistem S4 uyku durumunda ya da kapalıyken (S5) LED ışık kapanır.

HDLED (Sabit Disk Etkinlik LED'i):

Sabit sürücü etkinlik LED'ini kasa ön paneline bağlayın. Sabit sürücü veri okur ya da yazarken LED ışığı yanar.

Ön panel tasarımı kasaya göre değişiklik gösterebilir. Bir ön panel modülü, temel olarak bir güç anahtarı, sıfırlama anahtarı, güç LED'i, sabit sürücü aktivitesi LED'i, hoparlör gibi birimlerden oluşur. Kasanızın ön panel modülünü bu bağlantıya takmadan önce, kablo düzenlemeleri ile pin düzenlemelerinin düzgün şekilde yapıldığından emin olun.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Güç anahtarını bağlayın, kasa üzerindeki anahtar ile sistem durumu belirtecini aşağıdaki pim düzenine göre sıfırlayın. Kabloları bağlarken pozitif ve negatif pimleri not edin.

Türkçe

Güç LED’i ve Hoparlör

PLED-

SPEAKER

Bağlantısı (7 pimli SPK_PLED1) (bkz. sf.1, No. 16)

DUMMY +5V

PLED+

DUMMY

PLED+

Lütfen kasa güç LED’ini ve kasa hoparlörünü bu bağlantıya takın.

Seri ATA3 Bağlayıcıları (SATA3_0_1: bkz. sf.1, No. 8) (SATA3_2_4: bkz. s.1, No. 11) (SATA3_3_5:

SATA3_1

SATA3_5

SATA3_4

Bu altı SATA3 bağlayıcısı, veri aktarım hızı 6,0 Gb/ sn'ye kadar olan dahili

SATA3_0

depolama aygıtları için tasarlanmış SATA veri kablolarını destekler.

bkz. sf.1, No. 10)

SATA3_3

SATA3_2

Türkçe

USB 2.0 Bağlantıları (9 pimli USB1_2 (bkz. sf.1, No. 17) (9 pimli USB3_4) (bkz. sf.1, No. 18)

USB 3.0 Bağlantı (19-pin USB3_7_8) (bkz. sf.1, No. 7)

USB_PWR

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

-B +B

GND

DUMMY

GND

-A

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

Bu anakartta iki başlık vardır. Her USB 2.0 bağlantısı, iki adet bağlantı noktasını destekleyebilir.

Bu anakart üzerinde, I/O paneli üzerindeki dört USB

3.0 bağlantı noktasının yanı sıra, bir adet bağlantı bulunmaktadır. Her USB 3.0 bağlantısı, iki adet bağlantı noktasını destekleyebilir..

Asrock Fatal1ty E3V5 Performance Gaming/OC Quick Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual