Asrock B660M-HDVP/D5 User Manual

Version 1.0

Published December 2021

Copyright©2021 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium batter y adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel

: [phone] ext.123 (Standard International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI

logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

INTEL END USER SOFTWARE LICENSE AGREEMENT

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.

LICENSE. Licensee has a license under Intel ’s copyrights to reproduce Intel’s Soware
only in its unmodied and binary form, (with the accompanying documentation, the
“Soware”) for Licensee’s personal use only, and not commercial use, in connection with
Intel-based products for which the Soware has been provided, subject to the following
conditions:

(a) Licensee may not disclose, distribute or transfer any part of the So ware, and You agree
to prevent unauthorized copying of the Soware.

(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.

(c) Licensee may not sublicense the Soware.

(d) e Soware may contain the soware and other intellectual property of third party
suppliers, some of which may be identied in, and licensed in accordance with, an enclosed
license.txt le or other text or le.

(e) Intel has no obligation to provide any support, technical assistance or updates for the
Soware.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware
remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected
by the laws of the United States and other countries, and international treaty provisions.
Licensee may not remove any copyright notices from the Soware. Except as otherwise
expressly provided above, Intel grants no express or implied right under Intel patents,
copyrights, trademarks, or other intellectual property rights. Transfer of the license termi­nates Licensee’s right to use the Soware.

DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of
any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PUR­POSE.

LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS
WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF
BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG-

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN
IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT
obligate Licensee to provide Intel with comments or suggestions regarding the Soware.
However, if Licensee provides Intel with comments or suggestions for the modication,
correction, improvement or enhancement of (a) the Soware or (b) Intel products or
processes that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide,
perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under
Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments
and suggestions.

TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license
at any time if Licensee is in breach of any of its terms or conditions. Upon termination,
Licensee will immediately destroy or return to Intel all copies of the Soware.

THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License
Agreement and has the right to enforce all of its terms.

U.S. GOVERNMENT RESTRICTED RIGHTS. e Soware is a commercial item (as
dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial
computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent
with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide
the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation,
2200 Mission College Blvd., Santa Clara, CA 95054.

EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will
export/re-export the Soware, directly or indirectly, to any country for which the U.S.
Department of Commerce or any other agency or department of the U.S. Government
or the foreign government from where it is shipping requires an export license, or other
governmental approval, without rst obtaining any such required license or approval. In
the event the Soware is exported from the U.S.A. or re-exported from a foreign destina­tion by Licensee, Licensee will ensure that the distribution and export/re-export or import
of the Soware complies with all laws, regulations, orders, or other restrictions of the U.S.
Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will
be governed by the laws of the U.S.A. and Delaware, without regard to conict of laws
principles. e Parties to this Agreement exclude the application of the United Nations
Convention on Contracts for the International Sale of Goods (1980). e state and federal
courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising
out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue
in those courts. A Party that obtains a judgment against the other Party in the courts iden­tied in this section may enforce that judgment in any court that has jurisdiction over the
Parties.

Licensee’s specic rights may vary from country to country.

Contents

Chapter 1 Introduction 1

1.1 Package Contents 1

1.2 Specications 2

1.3 Motherboard Layout 6

1.4 I/O Panel 9

Chapter 2 Installation 11

2.1 Installing the CPU 12

2.2 Installing the CPU Fan and Heatsink 15

2.3 Installing Memory Modules (DIMM) 16

2.4 Expansion Slots (PCI and PCIe Slots) 18

2.5 Jumpers Setup 19

2.6 Onboard Headers and Connectors 20

2.7 M.2_SSD (NGFF) Module Installation Guide (M2_1) 25

Chapter 3 Software and Utilities Operation 29

3.1 Installing Drivers 29

3.2 ASRock Motherboard Utility (A-Tuning) 30

3.2.1 Installing ASRock Motherboard Utility (A-Tuning) 30

3.2.2 Using ASRock Motherboard Utility (A-Tuning) 30

3.3 ASRock Live Update & APP Shop 33

3.3.1 UI Overview 33

3.3.2 Apps 34

3.3.3 BIOS & Drivers 37

3.3.4 Setting 38

Chapter 4 UEFI SETUP UTILITY 39

4.1 Introduction 39

4.2 EZ Mode 40

4.3 Advanced Mode 41

4.3.1 UEFI Menu Bar 41

4.3.2 Navigation Keys 42

4.4 Main Screen 43

4.5 OC Tweaker Screen 44

4.6 Advanced Screen 59

4.6.1 CPU Conguration 60

4.6.2 Chipset Conguration 63

4.6.3 Storage Conguration 66

4.6.4 Super IO Conguration 67

4.6.5 ACPI Conguration 69

4.6.6 USB Conguration 70

4.6.7 Trusted Computing 71

4.7 Tools 73

4.8 Hardware Health Event Monitoring Screen 75

4.9 Security Screen 77

4.10 Boot Screen 78

4.11 Exit Screen 81

B660M-HDVP/D5
H610M-HDVP/D5

Chapter 1 Introduction

ank you for purchasing ASRock B660M-HDVP/D5 / H610M-HDVP/D5

motherboard, a reliable motherboard produced under ASRock’s consistently

stringent quality control. It delivers excellent performance with robust design

conforming to ASRock’s commitment to quality and endurance.

In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation

guide of the soware and utilities. Chapter 4 contains the conguration guide of

the BIOS setup.

Becau se the motherboard specication s and the BIOS soware might be upd ated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version w ill be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, plea se visit our webs ite for specic information about the model
you are using. You may nd the latest VGA cards and CPU support li st on ASRock’s
website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock B660M-HDVP/D5 / H610M-HDVP/D5 Motherboard (Micro ATX Form

•

Factor)

ASRock B660M-HDVP/D5 / H610M-HDVP/D5 Quick Installation Guide

•

ASRock B660M-HDVP/D5 / H610M-HDVP/D5 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x Screw for M.2 Socket

•

1 x I/O Panel Shield

•

English

1

1.2 Specications

Platform

CPU

•

•

•

•

•

•

Micro ATX Form Factor

Solid Capacitor design

Supports 12th Gen Intel® CoreTM Processors (LGA1700)

5 Power Phase design

Supports Intel® Hybrid Technology

Supports Intel® Turbo Boost Max 3.0 Technology

Chipset

Memory

Expansion
Slot

B660M-HDVP/D5:

Intel® B660

•

H610M-HDVP/D5:

Intel® H610

•

2 x DDR5 DIMM Slots

•

Max. capacity of system memor y: 64GB

•

Supports Intel® Extreme Memory Prole (XMP) 3.0

•

B660M-HDVP/D5:

Supports DDR5 non-ECC, un-buered memor y*

•

* Supports DDR5 4800 (1DPC) natively.

* Please refer to Memory Support List on ASRock's website for

more information. (http://www.asrock.com/)

H610M-HDVP/D5:

Supports DDR5 non-ECC, un-buered memor y up to 4800*

•

* Supports DDR5 4800 (1DPC) natively.

* Please refer to Memory Support List on ASRock's website for

more information. (http://www.asrock.com/)

1 x PCIe Gen4x16 Slot

•

* Supports NVMe SSD as boot disks

2 x PCIe Gen3x1 Slots

•

1 x PCI Slot

•

English

2

Graphics

Intel® UHD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU

integrated.

Intel® Xe Graphics Architecture (Gen 12)

•

Audio

LAN

B660M-HDVP/D5
H610M-HDVP/D5

Four graphics output options: D-Sub, DVI-D, HDMI and

•

DisplayPort 1.4

*Supports up to 3 displays simultaneously (for H610M-HDVP/

D5 only)

Supports Quad Monitor (for B660M-HDVP/D5 only)

•

Supports HDMI 2.1 TMDS Compatible with max. resolution

•

up to 4K x 2K (4096x2160) @ 60Hz

Supports DVI-D with max. resolution up to 1920x1200 @

•

60Hz

Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz

Supports DisplayPort 1.4 with DSC (compressed) max.

•

resolution up to 8K (7680x4320) @ 60Hz / 5K (5120x3200) @

120Hz

Supports HDCP 2.3 with HDMI 2.1 TMDS Compatible and

•

DisplayPort 1.4 Ports

7.1 CH HD Audio (Realtek ALC897 Audio Codec)

•

Supports Surge Protection

•

PCIE x1 Gigabit LAN 10/100/1000 Mb/s

•

Realtek RTL8111H

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

Rear Panel
I/O

1 x PS/2 Keyboard Port

•

1 x PS/2 Mouse Port

•

1 x Serial Port: COM1

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

1 x DisplayPort 1.4

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)

HD Audio Jacks: Line in / Front Speaker / Microphone

•

English

3

English

Storage

RAID (for
B660M­HDVP/D5
only)

Connector

B660M-HDVP/D5:

4 x USB 3.2 Gen1 Ports (Supports ESD Protection)

•

H610M-HDVP/D5:

2 x USB 3.2 Gen1 Ports (Supports ESD Protection)

•

4 x SATA3 6.0 Gb/s Connectors*

•

* If M2_1 is occupied by a SATA-type M.2 device, SATA3_0 will

be disabled.

1 x Ultra M.2 Socket (M2_1, Key M), supports type

•

2242/2260/2280 SATA3 6.0 Gb/s & PCIe Gen3 x4 (32 Gb/s)

mode**

** Supports Intel® OptaneTM Tech nol ogy (for B660M-HDVP/D5

only)

** Supports Intel® Volume Management Device (VMD) (for

B660M-HDVP/D5 only)

** Supports NVMe SSD as boot disks

** Supports ASRock U.2 Kit

Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA

•

storage devices

1 x Print Port Header

•

1 x COM Port Header

•

1 x SPI TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum

1A (12W) fan power.

1 x Chassis Fan Connector (4-pin)

•

* e Chassis Fan supports the Chassis fan of maximum 1A

(12W) fan power.

1 x Chassis/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control)

* e Chassis/Water Pump Fan supports the water cooler fan of

maximum 2A (24W) fan power.

* CHA_FAN1/WP can auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

4

BIOS
Feature

Hardware
Monitor

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports

•

ESD Protection)

1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)

•

(Supports ESD Protection)

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

B660M-HDVP/D5:

CPU Core/Cache, CPU GT, VDD_CPU, VDD_IMC, VCCIN

•

AUX, +1.05V PROC, +0.82V PCH , +1.05V PCH Voltage

Multi-adjustment

H610M-HDVP/D5:

CPU Core/Cache, CPU GT, VDD_CPU, VCCIN AUX,

•

+1.05V PROC, +0.82V PCH , +1.05V PCH Voltage Multi-

adjustment

Fan Tachometer: CPU, Chassis, Chassis/Water Pump Fans

•

Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, Chassis, Chassis/Water Pump Fans

Fan Multi-Speed Control: CPU, Chassis, Chassis/Water

•

Pump Fans

CASE OPEN detection

•

Voltage monitoring: CPU Vcore, +1.05V_PCH, VDD_CPU,

•

VCCIN AUX, +1.05V PROC, +0.82V PCH, +12V, +5V,

+3.3V, VCCSA

B660M-HDVP/D5
H610M-HDVP/D5

Microso® Windows® 10 64-bit / 11 64-bit

OS

Certica­tions

* For detailed product infor mation, please vis it our website: http://www.asrock .com

Please realize that there is a certain risk involved with overcl ocking, including
adjusting the setting in th e BIOS, applying Untie d Overclocking Technology, or using
third-party overclocking tools . Overclocking may aect your system’s stability, or
even cause damage to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for possible damage caused by
overclocking.

•

FCC, CE

•

ErP/EuP Ready (ErP/EuP ready power supply is required)

•

English

5

1.3 Motherboard Layout

3

4

1

5

2

ATXP WR 1

HDLED RESET

PLED PWRBTN

PANEL1

1

Ro HS

CPU_FAN1

PCIE1

PCI1

1

SPK_CI1

1

DDR 5_B1 (6 4 bit, 28 8-pin m odule )

DDR 5_A1 (6 4 bit, 28 8-pin m odule )

ATX12V1

USB3_ 1_2

1

HD_AUDIO1

M2_ 1

Top:

RJ-45

HDM I1

COM1

USB 2.0
T: USB_1
B: USB_2

CHA_FAN2

PCIE2

PCIE3

Top:

LINE IN

Cente r:

FRONT

Botto m:

MIC IN

VGA1

DVI1

1

USB_5_6

COM2

1

12

11

AUDIO

CODEC

B660M-HDV P/D5

14

10

CHA_FAN1/WP

PS2

Keyb oard

PS2

Mous e

18

Intel

B660

9

8

BIOS
ROM

1

SPI_TPM_J1

13

1

USB_3_4

15

LPT1

1

CMOS

Battery

19

USB 3.2 Gen1
USB3_3456

DP1

SATA3_0

SATA3_2

SATA3_1

SATA3_3

CLRMOS1

1

B660M-HDVP/D5

English

6

6

7

20

17

16

H610M-HDVP/D5

3

4

1

5

6

2

ATXP WR 1

HDLED RESET

PLED PWRBTN

PANEL1

1

Ro HS

CPU_FAN1

PCIE1

PCI1

1

SPK_CI1

1

DDR 5_B1 (6 4 bit, 28 8-pin m odule )

DDR 5_A1 (6 4 bit, 28 8-pin m odule )

ATX12V1

USB3_ 1_2

1

HD_AUDIO1

M2_ 1

Top:

RJ-45

HDM I1

COM1

USB 2.0
T: USB_1
B: USB_2

CHA_FAN2

PCIE2

PCIE3

Top:

LINE IN

Cente r:

FRONT

Botto m:

MIC IN

VGA1

DVI1

1

USB_5_6

COM2

1

12

11

AUDIO
CODEC

H610M-HDV P/D5

14

10

CHA_FAN1/WP

PS2

Keyb oard

PS2

Mous e

18

Intel

H610

9

8

BIOS
ROM

1

SPI_TPM_J1

13

1

USB_3_4

15

LPT1

1

CMOS

Battery

19

USB 3.2 Gen1
USB3_34

DP1

SATA3_0

SATA3_2

SATA3_1

SATA3_3

CLRMOS1

1

B660M-HDVP/D5
H610M-HDVP/D5

20

17

16

7

English

7

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 2 x 288-pin DDR5 DIMM Slots (DDR5_A1, DDR5_B1)

3 CPU Fan Connector (CPU_FAN1)

4 ATX Power Connector (ATXPWR1)

5 USB 3.2 Gen1 Header (USB3_1_2)

6 SATA3 Connector (SATA3_3)

7 SATA3 Connector (SATA3_2)

8 SATA3 Connector (SATA3_0)

9 SATA3 Connector (SATA3_1)

10 Chassis Intrusion and Speaker Header (SPK_CI1)

11 SPI TPM Header (SPI_TPM_J1)

12 System Panel Header (PANEL1)

13 Clear CMOS Jumper (CLRMOS1)

14 USB 2.0 Header (USB_5_6)

15 USB 2.0 Header (USB_3_4)

16 Chassis Fan Connector (CHA_FAN2)

17 Print Port Header (LPT1)

18 COM Port Header (COM2)

19 Front Panel Audio Header (HD_AUDIO1)

20 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

English

8

1.4 I/O Panel

B660M-HDVP/D5

1 2

3 4

B660M-HDVP/D5
H610M-HDVP/D5

5
6

13

No. Description No. Description

1 D-Sub Port 8 USB 2.0 Ports (USB_12)

2 Serial Port: COM1 9 USB 3.2 Gen1 Ports (USB3_3456)

3 PS/2 Mouse Port 10 PS/2 Keyboard Port

4 LAN RJ-45 Port* 11 DisplayPort 1.4

5 Line In (Light Blue)** 12 HDMI Port

6 Front Speaker (Lime)** 13 DVI-D Port

7 Microphone (Pink)**

9

78101112

English

9

H610M-HDVP/D5

1 2

3 4

5
6

13

9

No. Description No. Description

1 D-Sub Port 8 USB 2.0 Ports (USB_12)

2 Serial Port: COM1 9 USB 3.2 Gen1 Ports (USB3_34)

3 PS/2 Mouse Port 10 PS/2 Keyboard Port

4 LAN RJ-45 Port* 11 DisplayPort 1.4

5 Line In (Light Blue)** 12 HDMI Port

6 Front Speaker (Lime)** 13 DVI-D Port

7 Microphone (Pink)**

* ere are two LEDs on the LAN por t. Please refe r to the table belo w for the LA N port LED indications .

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

78101112

English

10

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Spea ker Out
Lime (Front panel) Side Speaker Out

B660M-HDVP/D5
H610M-HDVP/D5

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,

study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard

components.

In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded

wrist strap or touch a safety grounded object before you handle the components.

Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.

When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

11

English

2.1 Installing the CPU

1

1. Before you insert the 1700-Pin CPU into the socket, please check if the PnP cap is on the
socket, if the CPU surface is unclean, or if the re are any bent pins in the socket. Do not
force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.

2. Unplug all power c ables before installing the CPU.

2 3

A

B

English

12

B660M-HDVP/D5
H610M-HDVP/D5

4

76

5

13

English

Please save and replace the cover if the processor is removed. e cover must be placed if
you wish to return the motherboard for aer service.

English

14

2.2 Installing the CPU Fan and Heatsink

1 2

B660M-HDVP/D5
H610M-HDVP/D5

CPU_FAN

English

15

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR5 (Double Data Rate 5) DIMM slots,

and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identical (the same

brand, speed, size and chip-ty pe) DDR5 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology w ith only one memor y

module installed.

3. It is not allowed to instal l a DDR, DDR2, DDR3 or DDR4 memory modul e into a

DDR5 slot; otherwise, this mothe rboard and DIMM may be damage d.

e DIMM only ts in one correct orientation. It will cause permanent damage to
the motherboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.

English

16

B660M-HDVP/D5
H610M-HDVP/D5

1

2

3

English

17

2.4 Expansion Slots (PCI and PCIe Slots)

ere are 1 PCI slot and 3 PCIe slots on the motherboard.

Before installing an expansion c ard, please mak e sure that the powe r supply is
switched o or the power cord i s unplug ged. Please read the documentation of the
expan sion card and mak e necessary hardware settings for the card before you star t
the installation.

PCI slots:

e PCI1 slot is used to install expansion card that have 32-bit PCI interface.

PCIe slots:

PCIE1 (PCIe 4.0 x16 slot) is used for PCIe x16 lane width graphics cards.

PCIE2 (PCIe 3.0 x1 slot) is used for PCIe x1 lane width cards.

PCIE3 (PCIe 3.0 x1 slot) is used for PCIe x1 lane width cards.

English

18

B660M-HDVP/D5
H610M-HDVP/D5

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on

the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“O pen”.

Clear CMOS Jumper

(CLR MOS1)

(see p.6, 7, No. 13)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system

parameters to default setup, please turn o the computer and unplug the power

cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to

short the pins on CLRMOS1 for 5 seconds. However, please do not clear the

CMOS right aer you update the BIOS. If you need to clear the CMOS when you

just nish updating the BIOS, you must boot up the system rst, and then shut it

down before you do the clear-CMOS action. Please be noted that the password,

date, time, and user default prole will be cleared only if the CMOS battery is

removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

If you clear the CMOS, the case open may be detected. Please adjus t the BIOS option
“Clear Status” to cl ear the record of prev ious chassis intru sion status.

English

19

2.6 Onboard Headers and Connectors

1

Onboard headers and connectors are NOT jumpers. Do NOT pla ce jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

System Panel Header

(9-p in PA NE L1)

(see p.6 , 7, No. 12)

PWRBTN (Power Swi tch):

Connec t to the power switch on the chassis f ront panel. You may congure the way to
turn o your system using the power sw itch.

RESET (Reset Sw itch):
Connec t to the reset switch on the chassis f ront panel. Pre ss the reset switch to restart
the computer if the computer f reezes and fails to per form a normal restart.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chassi s front panel. e LED is on when
the system is operating. e LED keeps blinking whe n the system is in S1/S3 sle ep
state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis f ront panel. e LED is on
when the hard drive is reading or writing data.

e front panel design may dier by chassis . A front panel module mainly consists
of power s witch, reset switch, power LED, hard drive ac tivity LED, speaker and etc.
When connecting your cha ssis front panel modul e to this header, make sure the wire
assig nments and the pin assignments are matched correc tly.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

GND

Connect the power switch,

reset switch and system status

indicator on the chassis to

this header according to the

pin assignments below. Note

the positive and negative pins

before connecting the cables.

English

20

B660M-HDVP/D5

1

+5V

DUMMY

SIGNAL

GND

DUMMY

SPEAKER

DUMMY

DUMMY

GND

GND

P+

P-

USB_PWR

P+

P-

USB_PWR

1

H610M-HDVP/D5

Chassis Intrusion and

Speaker Header

(7-pi n SPK_C I1)

(see p.6, 7, No. 10)

Serial ATA3 Connectors

Ver ti ca l:

(SATA3_0:

see p.6, 7, No. 8)

(SATA3_1:

see p.6, 7, No. 9)

(SATA3_2:

see p.6, 7, No. 7)

(SATA3_3:

see p.6, 7, No. 6)

USB 2.0 Headers

(9-pin USB_3_4)

(see p.6, 7, No. 15)

(9-pin USB_5_6)

(see p.6, 7, No. 14)

SATA3_3

SATA3_1

Please connect the

chassis intrusion and the

chassis speaker to this header.

ese four SATA3 connectors

support SATA data cables for

internal storage devices with

SATA3_2

up to 6.0 Gb/s data transfer

rate.

*If M2_1 is occupied by

SATA3_0

a SATA-type M.2 device,

SATA3_0 will be disabled.

ere are two USB 2.0 headers

on this motherboard.Each

USB 2.0 header can support

two ports.

USB 3.2 Gen1 Header

(19-pin USB3_1_2)

(see p.6, 7, No. 5)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

1

ere is one USB 3.2 Gen1

header on this motherboard.

is USB 3.2 Gen1 header can

support two ports.

English

21