Asrock B660M-HDV Quick Installation Guide

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel

: +886-2-28965588 ext.123 (Standard International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

INTEL END USER SOFTWARE LICENSE AGREEMENT

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.

LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Soware only in its unmodied and binary form, (with the accompanying documentation, the “Soware”) for Licensee’s personal use only, and not commercial use, in connection with Intel-based products for which the Soware has been provided, subject to the following conditions:

(a) Licensee may not disclose, distribute or transfer any part of the Soware, and You agree to prevent unauthorized copying of the Soware.

(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.

(d) e Soware may contain the soware and other intellectual property of third party suppliers, some of which may be identied in, and licensed in accordance with, an enclosed license.txt le or other text or le.

(e) Intel has no obligation to provide any support, technical assistance or updates for the Soware.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected by the laws of the United States and other countries, and international treaty provisions. Licensee may not remove any copyright notices from the Soware. Except as otherwise expressly provided above, Intel grants no express or implied right under Intel patents, copyrights, trademarks, or other intellectual property rights. Transfer of the license terminates Licensee’s right to use the Soware.

DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG

ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT obligate Licensee to provide Intel with comments or suggestions regarding the Soware. However, if Licensee provides Intel with comments or suggestions for the modication, correction, improvement or enhancement of (a) the Soware or (b) Intel products or processes that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide, perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments and suggestions.

TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license at any time if Licensee is in breach of any of its terms or conditions. Upon termination, Licensee will immediately destroy or return to Intel all copies of the Soware.

THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License Agreement and has the right to enforce all of its terms.

U.S. GOVERNMENT RESTRICTED RIGHTS. e Soware is a commercial item (as dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95054.

EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will export/re-export the Soware, directly or indirectly, to any country for which the U.S. Department of Commerce or any other agency or department of the U.S. Government or the foreign government from where it is shipping requires an export license, or other governmental approval, without rst obtaining any such required license or approval. In the event the Soware is exported from the U.S.A. or re-exported from a foreign destination by Licensee, Licensee will ensure that the distribution and export/re-export or import of the Soware complies with all laws, regulations, orders, or other restrictions of the U.S. Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will be governed by the laws of the U.S.A. and Delaware, without regard to conict of laws principles. e Parties to this Agreement exclude the application of the United Nations Convention on Contracts for the International Sale of Goods (1980). e state and federal courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue in those courts. A Party that obtains a judgment against the other Party in the courts identied in this section may enforce that judgment in any court that has jurisdiction over the Parties.

Licensee’s specic rights may vary from country to country.

Motherboard Layout

Intel

B660

ATXP WR 1

HDLED RESET

PLED PWRBTN

PANEL1

RoHS

CPU_FAN1

PCIE1

SPK_CI1

PCIE2

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

ATX12V1

SATA3_1

SATA3_0

F_USB 3_1_2

CLRMOS1

HD_AUDIO1

M2_ 2

Top:

RJ-45

HDMI1

CPU_FAN2/WP

USB 2.0 T: USB_1 B: USB_2

CHA_FAN1/WP

PCIE3

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

VGA 1

USB 3.2 G en1

T: USB3_1

B: USB3 _2

PS2

Keyb oard

/Mou se

SPI_TPM_J1

USB3_4

M2_ 1

BIOS ROM

CHA_FAN2/WP

COM1

CMOS

Battery

SATA3_2

SATA3_3

LAN

AUDIO CODEC

B6 6 0M - HD V

M2_ WIFI

USB 3.2 Gen1 T: USB3_TA_1 B: USB3_TC_1

DP_1

USB5

B660M-HDV

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

5 ATX Power Connector (ATXPWR1)

6 USB 3.2 Gen1 Header (F_USB3_1_2)

7 SATA3 Connector (SATA3_1)

8 SATA3 Connector (SATA3_0)

9 SATA3 Connectors (SATA3_2)(Upper), (SATA3_3)(Lower)

10 SPI TPM Header (SPI_TPM_J1)

11 System Panel Header (PANEL1)

12 Clear CMOS Jumper (CLRMOS1)

13 Chassis Intrusion and Speaker Header (SPK_CI1)

14 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

15 USB 2.0 Header (USB5)

16 USB 2.0 Header (USB3_4)

17 COM Port Header (COM1)

18 Front Panel Audio Header (HD_AUDIO1)

19 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

English

I/O Panel

B660M-HDV

No. Description No. Description

1 PS/2 Mouse/Keyboard Port 7 USB 2.0 Ports (USB_1_2)

USB 3.2 Gen1 Type-A Port

(USB3_TA_1)

USB 3.2 Gen1 Type-C Port

(USB3_TC_1)

3 LAN RJ-45 Port* 9 USB 3.2 Gen1 Ports (USB3_1_2)

4 Line In (Light Blue)** 10 D-Sub Port

5 Front Speaker (Lime)** 11 HDMI Port

6 Microphone (Pink)** 12 DisplayPort 1.4

* ere are two LEDs on ea ch LAN port. Please refer to the table below for the LA N port LED indications .

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

English

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out

English

Chapter 1 Introduction

ank you for purchasing ASRock B660M-HDV motherboard, a reliable motherboard produced under ASRock ’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.

Becau se the motherboard specication s and the BIOS soware might be updated, the content of this doc umentation will be subject to change without notice. In case any modications of this documentation occur, the updated version w ill be available on ASRock’s website without further notice. If you require technical support related to this motherboard, please visit our website for specic infor mation about the model you are using. You may nd the latest VGA cards and CPU support li st on ASRock’s website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock B660M-HDV Motherboard (Micro ATX Form Factor)

•

ASRock B660M-HDV Quick Installation Guide

•

ASRock B660M-HDV Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

3 x Screws for M.2 Sockets (Optiona l)

•

1 x I/O Panel Shield

•

B660M-HDV

English

1.2 Specications

Platform

CPU

Chipset

Memory

* Supports DDR4 3200 natively. * Please refer to Memory Support List on ASRock's website for more information. (http://www.asrock.com/)

Micro ATX Form Factor

•

Solid Capacitor design

•

Supports 12th Gen Intel® CoreTM Processors (LGA1700)

•

Digi Power design

•

6 Power Phase design

•

Supports Intel® Hybrid Technology

•

Supports Intel® Turbo Boost Max 3.0 Technology

•

Intel® B660

•

Dual Channel DDR4 Memory Technology

•

2 x DDR4 DIMM Slots

•

Supports DDR4 non-ECC, un-buered memory up to

•

5066+(OC)*

Supports ECC UDIMM memory modules (operate in non-

•

ECC mo de) Max. capacity of system memory: 64GB

•

Supports Intel® Extreme Memory Prole (XMP) 2.0

•

English

Expansion Slot

Graphics

1 x PCIe Gen4x16 Slot*

•

* Supports NVMe SSD as boot disks

2 x PCIe Gen3x1 Slots

•

1 x M.2 Socket (Key E), supports type 2230 WiFi/BT PCIe

•

WiFi module

* Intel® UHD Graphics Built-in Visuals and the VGA outputs can be supported only with processors which are GPU integrated.

Intel® Xe Graphics Architecture (Gen 12)

•

ree graphics output options: D-Sub, HDMI and

•

DisplayPort 1.4 Supports HDMI 2.1 TMDS Compatible with max. resolution

•

up to 4K x 2K (4096x2160) @ 60Hz

Audio

LAN

Rear Panel I/O

Supports DisplayPort 1.4 with DSC (compressed) max.

•

resolution up to 8K (7680x4320) @ 60Hz / 5K (5120x3200) @ 120Hz Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz Supports HDCP 2.3 with HDMI 2.1 TMDS Compatible and

•

DisplayPort 1.4 Ports

7.1 CH HD Audio (Realtek ALC897/887 Audio Codec)

•

Supports Surge Protection

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports UEFI PXE

•

2 x Antenna Mounting Points

•

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x HDMI Port

•

1 x DisplayPort 1.4

•

3 x USB 3.2 Gen1 Type-A Ports (Supports ESD Protection)

•

1 x USB 3.2 Gen1 Type-C Port (Supports ESD Protection)

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED) HD Audio Jacks: Line in / Front Speaker / Microphone

•

B660M-HDV

Storage

4 x SATA3 6.0 Gb/s Connectors*

•

* If M2_2 is occupied by a SATA-type M.2 device, SATA3_3 will be disabled.

1 x Hyper M.2 Socket (M2_1, Key M), supports type

•

2260/2280 PCIe Gen4x4 (64 Gb/s) mode** 1 x Ultra M.2 Socket (M2_2, Key M), supports type

•

2260/2280 SATA3 6.0 Gb/s & PCIe Gen3x4 (32 Gb/s) modes**

English

RAID

Connector

** Supports Intel® OptaneTM Technology (M2_2 only) ** Supports Intel® Volume Management Device (VMD) ** Supports NVMe SSD as boot disks ** Supports ASRock U.2 Kit

Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA

•

storage devices

1 x COM Port Header

•

1 x SPI TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control) * e CPU/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.

2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control) * e Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power. * CPU_FAN2/WP and CHA_FAN1~2/WP can auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 3 USB 2.0 ports) (Supports

•

ESD Protection)

1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)

•

(Supports ESD Protection)

English

BIOS Feature

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU Core/Cache, CPU GT, DRAM, VCCIN AUX, +1.05V

•

PROC, +0.82V PCH, +1.05V PCH Voltage Multi-adjustment

Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

Hardware Monitor

•

Pump Fans Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

•

Water Pump Fans CASE OPEN detection

•

Voltage monitoring: CPU Vcore, +1.05 PCH, DRAM, VC-

•

CIN AUX, +1.05V PROC, +0.82V PCH, +12V, +5V, +3.3V

Microso® Windows® 10 64-bit / 11 64-bit

Certications

* For detailed product infor mation, please visit our website: http://www.asrock .com

Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may aect your system’s stability, or even cause damage to the components and devices of your system . It should be done at your own risk and expen se. We are not responsible for possible damage caused by overclocking.

•

FCC, CE

•

ErP/EuP Ready (ErP/EuP ready power supply is required)

•

B660M-HDV

English

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

2.1 Installing the CPU

1. Before you insert the 1700-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation i s found. Other wise, the CPU will be seriously damaged.

2. Unplug all power cables before installing the CPU.

B660M-HDV

2 3

English

Please save and replace the cover if the processor is removed. e cover must be placed if you wish to return the motherboard for aer service.

2.2 Installing the CPU Fan and Heatsink

1 2

B660M-HDV

CPU_FAN

English

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identical (the same brand, speed, size and chip-ty pe) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology w ith only one memor y module installed.

3. It is not allowed to install a DDR, DDR2 or DDR 3 memory module into a DDR4 slot; otherwi se, this motherboard and DIMM may be damaged .

e DIMM only ts in one correct orientation. It will cause permanent damage to the mothe rboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

English

B660M-HDV

English

2.4 Expansion Slots (PCI Express Slots)

ere are 3 PCI Express slots on the motherboard.

Before installing an expansion card, ple ase make sure that the power supply is switched o or the power cord is unplug ged. Please read the documentation of the expan sion card and make necessary hardware settings for the card before you start the installation.

PCIe slots:

PCIE1 (PCIe 4.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“Open”.

Clear CMOS Jumper (CLR MOS1) (see p.1, No. 12)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short the pins on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

B660M-HDV

If you clear the CMOS, the case open may be detected. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

English

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

System Panel Header (9-p in PA NEL1) (see p.1, No. 11)

PWRBTN (Power Swi tch):

Connec t to the power switch on the chassis f ront panel. You may congure the way to turn o your system using the power switch.

RESET (Reset Sw itch): Connec t to the reset switch on the cha ssis front panel. Press the reset switch to restar t the computer if the computer f reezes and fails to per form a normal restart.

PLED (Syste m Power LED): Connec t to the power status indicator on the chassi s front panel. e LED is on when the system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e LED is o when the system is in S4 sleep state or powe red o (S5).

HDLED (Ha rd Drive Activity LED): Connec t to the hard drive activity LED on the chassis f ront panel. e LED is on when the hard drive is reading or writing data.

e front panel design may dier by chassis . A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your cha ssis front panel module to this header, make sure the wire assig nments and the pin assignments are matched correctly.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

English

B660M-HDV

SPEAKER

Chassis Intrusion and Speaker Header (7-pi n SPK_C I1) (see p.1, No. 13)

Serial ATA3 Connectors Ver tical: (SATA3_0: see p.1, No. 8) (SATA3_1: see p.1, No. 7) Right Angle: (SATA3_2: see p.1, No. 9)(Upper) (SATA3_3: see p.1, No. 9)(Lower)

USB 2.0 Headers (9-pin USB3_4) (see p.1, No. 16)

(4-pin USB5) (see p.1, No. 15)

DUMMY +5V

SIGNAL

SATA3_2 SATA3_1

USB_PWR

DUMMY

GND

DUMMY

P-

P+

P-

P+0

P-0

GND

DUMMY

GND

Please connect the chassis intrusion and the chassis speaker to this header.

ese four SATA3 connectors support SATA data cables for internal

SATA3_0SATA3_3

storage devices with up to

6.0 Gb/s data transfer rate. * If M2_2 is occupied by a SATA-type M.2 device, SATA3_3 will be disabled.

ere are two USB

2.0 headers on this motherboard.

USB 3.2 Gen1 Header (19-pin F_USB3_1_2) (see p.1, No. 6)

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

ere is one header on this motherboard. is USB 3.2 Gen1 header can support two ports.

English

Front Panel Audio Header

GND

(9-pin HD_AUDIO1) (see p.1, No. 18)

1. High Denition Audio supports Ja ck Sensing, but the panel wire on the chassis must support HDA to function correctly. Plea se follow the instructions in our manual and chassis manual to install your system.

2. If you use an AC’97 audio panel , please install it to the f ront panel audio header by the steps below: A. Connect Mic_ IN (MIC) to MIC2_L. B. Conne ct Audio_R (RIN) to OUT2 _R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel. E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.

GND

PRESENCE#

MIC2_R

MIC2_L

MIC_RET

J_SENSE

OUT2_R

OUT_RET

OUT2_L

is header is for connecting audio devices to the front audio panel.

English

Chassis/Water Pump Fan Connectors (4-pin CHA_FAN1/WP) (see p.1, No. 4)

(4-pin CHA_FAN2/WP) (see p.1, No. 14)

CPU Fan Connector (4-pin CPU_FAN1) (see p.1, No. 2)

FAN_SPEED_CONTROL

CHA_FAN_SPEED

FAN_VOLTAGE

CHA_FAN_SPEED

FAN_SPEED_CONTROL

1 2 3 4

FAN_SPEED_CONTROL

CPU_FAN_SPEED

+12V

GND

1234

4 3 2 1

GND

is motherboard provides two 4-Pin water cooling

chassis

fan connectors. If you plan to connect a 3-Pin

chassis water cooler fan, please connect it to Pin 1-3.

is motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

B660M-HDV

8 5

SPI_DQ3

CPU/Water Pump Fan Connector (4-pin CPU_FAN2/WP) (see p.1, No. 19)

ATX Power Connector (24-pin AT XPWR 1) (see p.1, No. 5)

ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 1)

FAN_SPEED_CONTROL

CPU_FAN_SPEED

FAN_VOLTAGE

GND

is motherboard

provides a 4-Pin water

3 2

cooling CPU fan

connector. If you plan to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.

is motherboard provides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin

13.

is motherboard provides a 8-pin ATX 12V power connector. To use a

4-pin ATX power supply, please plug it along Pin 1 and Pin 5.

*Warning: Please make

sure that the power cable

connected is for the CPU

and not the graphics

card. Do not plug the

PCIe power cable to this

connec tor.

SPI TPM Header (13 -pin SPI_TPM _ J1) (see p.1, No. 10)

SPI_PWR

SPI_CS0

SPI_DQ2

Dummy

CLK

RSMRST#

SPI_MISO

SPI_MOSI

RST#

TPM_PIRQ

SPI_TPM_CS#

GND

is connector supports SPI Trusted Platform Module (TPM) system, which can securely store keys, digital certicates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integr it y.

English

Serial Port Header (9-pin COM1) (see p.1, No. 17)

RRXD1

DDTR#1

TTXD1

DDCD#1

DDSR#1

CCTS#1

RRTS#1

GND

is COM1 header supports a serial port module.

RRI#1

English

B660M-HDV

2.7 M.2 WiFi/BT PCIe WiFi Module Installation Guide

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key E) supports type 2230 WiFi/BT PCIe WiFi module. * e M.2 socket does not support SATA M.2 SSDs.

Installing the WiFi/BT module

Step 1

Prepare a type 2230 WiFi/BT PCIe WiFi module and the screw.

Step 2

Find the nut location to be used.

PCB Length: 3cm Module Type: Type2230

English

Step 3

Gently insert the WiFi/BT module into the M.2 slot. Please be aware that the module only ts in one orientation.

Step 4

Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw as this might damage the module.

English

2.8 M.2_SSD (NGFF) Module Installation Guide (M2_1)

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. e Hyper M.2 Socket (M2_1, Key M) supports type 2260/2280 PCIe Gen4x4 (64 Gb/s) mode.

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module and the screw.

B660M-HDV

No. 1 2

Nut Location A B

PCB Length 6cm 8cm

Module Type Type 2 260 Type 2 280

Step 2

Depending on the PCB type and length of your M.2_SSD (NGFF) module, nd the corresponding nut location to be used.

English

Step 3

Move the stando based on the module type and length. e stando is placed at the nut location B by default. Skip Step 3 and

4 and go straight to Step 5 if you are going to use the default nut. Otherwise, release the stando by hand.

Step 4

Peel o the yellow protective lm on the nut to be used. Hand tighten the

stando into the desired nut location on the motherboard.

Step 5

Gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware that the M.2 (NGFF) SSD

module only ts in one orientation.

English

Step 6

Tighten the screw with a screwdriver to secure the module into place. Please do not overtighten the screw

NUT1NUT2

as this might damage the module.

+ 132 hidden pages

Asrock B660M-HDV Quick Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual