Asrock B560 Pro4 Quick Installation Guide

No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc.

Products and corporate names appearing in this documentation may or may not be registered trademarks or copyrights of their respective companies, and are used only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of prots, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. When you discard the Lithium battery in California, USA, please follow the related regulations in advance. “Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/ perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. If you require assistance please call ASRock Tel

: +886-2-28965588 ext.123 (Standard International call charges apply)

e terms HDMI® and HDMI High-Denition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United

States and other countries.

INTEL END USER SOFTWARE LICENSE AGREEMENT

IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING.

LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s Soware only in its unmodied and binary form, (with the accompanying documentation, the “Soware”) for Licensee’s personal use only, and not commercial use, in connection with Intel-based products for which the Soware has been provided, subject to the following conditions:

(a) Licensee may not disclose, distribute or transfer any part of the Soware, and You agree to prevent unauthorized copying of the Soware.

(b) Licensee may not reverse engineer, decompile, or disassemble the Soware.

(d) e Soware may contain the soware and other intellectual property of third party suppliers, some of which may be identied in, and licensed in accordance with, an enclosed license.txt le or other text or le.

(e) Intel has no obligation to provide any support, technical assistance or updates for the Soware.

OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Soware remains with Intel or its licensors or suppliers. e Soware is copyrighted and protected by the laws of the United States and other countries, and international treaty provisions. Licensee may not remove any copyright notices from the Soware. Except as otherwise expressly provided above, Intel grants no express or implied right under Intel patents, copyrights, trademarks, or other intellectual property rights. Transfer of the license terminates Licensee’s right to use the Soware.

DISCLAIMER OF WARRANTY. e Soware is provided “AS IS” without warranty of any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

LIMITATION OF LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS WILL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN

IF INTEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

LICENSE TO USE COMMENTS AND SUGGESTIONS. is Agreement does NOT obligate Licensee to provide Intel with comments or suggestions regarding the Soware. However, if Licensee provides Intel with comments or suggestions for the modication, correction, improvement or enhancement of (a) the Soware or (b) Intel products or processes that work with the Soware, Licensee grants to Intel a non-exclusive, worldwide, perpetual, irrevocable, transferable, royalty-free license, with the right to sublicense, under Licensee’s intellectual property rights, to incorporate or otherwise utilize those comments and suggestions.

TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this license at any time if Licensee is in breach of any of its terms or conditions. Upon termination, Licensee will immediately destroy or return to Intel all copies of the Soware.

THIRD PARTY BENEFICIARY. Intel is an intended beneciary of the End User License Agreement and has the right to enforce all of its terms.

U.S. GOVERNMENT RESTRICTED RIGHTS. e Soware is a commercial item (as dened in 48 C.F.R. 2.101) consisting of commercial computer soware and commercial computer soware documentation (as those terms are used in 48 C.F.R. 12.212), consistent with 48 C.F.R. 12.212 and 48 C.F.R 227.7202-1 through 227.7202-4. You will not provide the Soware to the U.S. Government. Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA 95054.

EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries will export/re-export the Soware, directly or indirectly, to any country for which the U.S. Department of Commerce or any other agency or department of the U.S. Government or the foreign government from where it is shipping requires an export license, or other governmental approval, without rst obtaining any such required license or approval. In the event the Soware is exported from the U.S.A. or re-exported from a foreign destination by Licensee, Licensee will ensure that the distribution and export/re-export or import of the Soware complies with all laws, regulations, orders, or other restrictions of the U.S. Export Administration Regulations and the appropriate foreign government.

APPLICABLE LAWS. is Agreement and any dispute arising out of or relating to it will be governed by the laws of the U.S.A. and Delaware, without regard to conict of laws principles. e Parties to this Agreement exclude the application of the United Nations Convention on Contracts for the International Sale of Goods (1980). e state and federal courts sitting in Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising out of or relating to this Agreement. e Parties consent to personal jurisdiction and venue in those courts. A Party that obtains a judgment against the other Party in the courts identied in this section may enforce that judgment in any court that has jurisdiction over the Parties.

Licensee’s specic rights may vary from country to country.

Motherboard Layout

Intel

B560

DDR 4_A2 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

DDR 4_B2 (6 4 bit, 28 8-pin m odule )

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

USB 2. 0

T: USB1

B: USB 2

ATXP WR 1

PCIE1

Top: RJ-45

USB 3.2 Gen1 T: USB3_1 B: USB3_2

PCIE3

HDLED RESET

PLED PWRBTN

HD_AUDIO1

PS2

Keybo ard

/Mous e

CMOS

Battery

PCIE2

M2_ 1

C 10

C 9

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

M2_ WIFI1

M2_WIFI_CT1

M2_ 3

C 23

C 24

HDM I1

PCIE4

AUDIO

CODEC

CHA_FAN 5/WP

CHA_FAN1/WP

CHA_FAN2/WP

CPU_FAN2/WP

CPU_FAN1

CHA_FAN4/ WP

SUPER

I/O

USB3_5 _6

USB31_ TC_1

RGB_LE D2

ADDR_L ED2

RoHS

C 7

ADDR_LED1

RGB_LED1

USB3_4

SATA3_0 SATA3_1

CLRMOS1

PANEL1

ATX12V1

SPI_TPM_J1

SATA3_4

SATA3_5

D 1 P

USB3_7 _8

SATA3_2

SATA3_3

C 8

M2_ 2

C 12

C 13

C 14

C 11

SPK_CI1

CHA_FAN3/WP

COM1

DRAM

BOOT

VGA

CPU

USB 3.2 Gen1 T: USB3_3 B: USB3_4

B560 Pro4

English

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)

4 CPU Fan Connector (CPU_FAN1)

5 CPU/Water Pump Fan Connector (CPU_FAN2/WP)

6 Addressable LED Header (ADDR_LED2)

7 RGB LED Header (RGB_LED2)

8 Chassis/Water Pump Fan Connector (CHA_FAN5/WP)

9 ATX Power Connector (ATXPWR1)

10 Front Panel Type C USB 3.2 Gen1 Header (USB31_TC_1)

11 USB 3.2 Gen1 Header (USB3_7_8)

12 USB 3.2 Gen1 Header (USB3_5_6)

13 SATA3 Connector (SATA3_2)

14 SATA3 Connector (SATA3_3)

15 SATA3 Connector (SATA3_4)

16 SATA3 Connector (SATA3_5)

17 Chassis/Water Pump Fan Connector (CHA_FAN4/WP)

18 Post Status Checker (PSC)

19 SPI TPM Header (SPI_TPM_J1)

20 SATA3 Connector (SATA3_1)

21 SATA3 Connector (SATA3_0)

22 System Panel Header (PANEL1)

23 Clear CMOS Jumper (CLRMOS1)

24 USB 2.0 Header (USB3_4)

25 Chassis Intrusion and Speaker Header (SPK_CI1)

26 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

27 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)

28 Addressable LED Header (ADDR_LED1)

29 RGB LED Header (RGB_LED1)

30 COM Port Header (COM1)

31 Front Panel Audio Header (HD_AUDIO1)

32 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

I/O Panel

B560 Pro4

No. Description No. Description

1 USB 2.0 Ports (USB1_2) 6 USB 3.2 Gen1 Ports (USB3_1_2)

2 LAN RJ-45 Port* 7 USB 3.2 Gen1 Ports (USB3_3_4)

3 Line In (Light Blue)** 8 DisplayPort 1.4

4 Front Speaker (Lime)** 9 HDMI Port

5 Microphone (Pink)** 10 PS/2 Mouse/Keyboard Port

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection Blinking Data Activity Orange 100Mbps connection On Link Green 1Gbps connection

** Function of the Audio Ports in 7.1-channel Conguration:

Port Function

Light Blue (Rear panel) Rear Speaker Out Lime (Rear panel) Front Speaker Out Pink (Rear panel) Central /Subwoofer Speaker Out Lime (Front panel) Side Speaker Out

English

Chapter 1 Introduction

ank you for purchasing ASRock B560 Pro4 motherboard, a reliable motherboard produced under ASRock ’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock ’s commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the content of this documentation will be subject to change without notice. In case any modications of this documentation occur, the updated version will be available on ASRock’s website without further notice. If you require technical support related to this motherboard, please vi sit our website for s pecic information about the model you are using. You may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock B560 Pro4 Motherboard (ATX Form Factor)

•

ASRock B560 Pro4 Quick Installation Guide

•

ASRock B560 Pro4 Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

4 x Screws for M.2 Sockets (Optional)

•

1 x Stando for M.2 Socket (Optional)

•

1 x I/O Panel Shield

•

English

1.2 Specications

Platform

CPU

Chipset

Memory

* 11th Gen Intel® CoreTM (i9/i7/i5) support DDR4 up to 2933; CoreTM (i3), Pentium® and Celeron® support DDR4 up to 2666. * 10th Gen Intel® CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3), Pentium® and Celeron® support DDR4 up to 2666. * Please refer to Memory Support List on ASRock's website for more information. (http://www.asrock.com/)

ATX Form Factor

•

Solid Capacitor design

•

Suppor ts 10th Gen Intel® CoreTM Processors and 11th Gen

•

Intel® CoreTM Processors (LGA1200) Digi Power design

•

8 Power Phase design

•

Supports Intel® Turbo Boost Max 3.0 Technology

•

Intel® B560

•

Dual Channel DDR4 Memory Technology

•

4 x DDR4 DIMM Slots

•

11th Gen Intel® CoreTM Processors support DDR4 non-ECC,

•

un-buered memory up to 4800+(OC)* 10th Gen Intel® CoreTM Processors support DDR4 non-ECC,

•

un-buered memory up to 4600+(OC)*

Supports ECC UDIMM memory modules (operate in non-

•

ECC mode) Max. capacity of system memory: 128GB

•

Supports Intel® Extreme Memory Prole (XMP) 2.0

•

B560 Pro4

English

Expansion Slot

11th Gen Intel® CoreTM Processors

2 x PCI Express x16 Slots (PCIE1/PCIE3: single at Gen4x16

•

(PCIE1); dual at Gen4x16 (PCIE1) / Gen3x2 (PCIE3))*

10th Gen Intel® CoreTM Processors

2 x PCI Express x16 Slots (PCIE1/PCIE3: single at Gen3x16

•

(PCIE1); dual at Gen3x16 (PCIE1) / Gen3x2 (PCIE3))*

* Supports NVMe SSD as boot disks

2 x PCI Express 3.0 x1 Slots

•

1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module

•

and Intel® CNVi (Integrated WiFi/BT)

English

Graphics

* Intel® UHD Graphics Built-in Visuals and the VGA outputs can be supported only with processors which are GPU integrated.

11th Gen Intel® CoreTM Processors support Intel® Xe Graphics

•

Architecture (Gen 12). 10th Gen Intel® CoreTM Processors support Gen 9 Graphics Graphics, Media & Compute: Microso DirectX 12, OpenGL

•

4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid / Switchable Graphics, OpenCL 2.1 Display & Content Security: Rec. 2020 (Wide Color Gamut),

•

Microso PlayReady 3.0, UHD/HDR Blu-ray Disc Dual graphics output: support HDMI and DisplayPort 1.4

•

ports by independent display controllers Supports HDMI 2.0 with max. resolution up to 4K x 2K

•

(4096x2160) @ 60Hz Supports DisplayPort 1.4 with max. resolution up to 4K x 2K

•

(4096x2304) @ 60Hz Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI 2.0 Port

(Compliant HDMI monitor is required)

Supports HDCP 2.3 with HDMI 2.0 and DisplayPort 1.4

•

Ports Supports 4K Ultra HD (UHD) playback with HDMI 2.0 and

•

DisplayPort 1.4 Ports * 11th Gen Intel® CoreTM Processors support HDMI 2.0. 10th Gen Intel® CoreTM Processors support HDMI 1.4.

Audio

LAN

Rear Panel I/O

7.1 CH HD Audio (Realtek ALC897 Audio Codec)

•

Supports Surge Protection

•

Nahimic Audio

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

3 x Antenna Mounting Points

•

1 x PS/2 Mouse/Keyboard Port

•

1 x HDMI Port

•

1 x DisplayPort 1.4

•

4 x USB 3.2 Gen1 Ports (Supports ESD Protection)

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED) HD Audio Jacks: Line in / Front Speaker / Microphone

•

B560 Pro4

Storage

6 x SATA3 6.0 Gb/s Connectors, support Intel Rapid Storage

•

Technology 18, NCQ, AHCI and Hot Plug* * If M2_3 is occupied by a SATA-type M.2 device, SATA3_1 will be disabled.

1 x Hyper M.2 Socket (M2_1), supports M Key type

•

2242/2260/2280 M.2 PCI Express module up to Gen4x4

(64 Gb/s) (Only supported with 11th Gen Intel® CoreTM

Processors)**

1 x Ultra M.2 Socket (M2_2), supports M Key type

•

2242/2260/2280 M.2 PCI Express module up to Gen3 x4 (32

Gb/s)**

1 x M.2 Socket (M2_3), supports M Key type 2280/22110 M.2

•

SATA3 6.0 Gb/s module and M.2 PCI Express module up to

Gen3 x2 (16 Gb/s)** ** Supports Intel® OptaneTM Tech nolo gy (M 2_ 2) ** Supports NVMe SSD as boot disks ** Supports ASRock U.2 Kit

English

Connector

1 x COM Port Header

•

1 x SPI TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

2 x RGB LED Headers

•

* Support in total up to 12V/3A, 36W LED Strip

2 x Addressable LED Headers

•

* Support in total up to 5V/3A, 15W LED Strip

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.

1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan

•

Speed Control) * e CPU/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.

5 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control) * e Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power. * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP, CHA_ FAN3/WP, CHA_FAN4/WP and CHA_FAN5/WP can auto detect if 3-pin or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector (Hi-Density Power Connec-

•

tor)

1 x Front Panel Audio Connector

•

1 x USB 2.0 Header (Supports 2 USB 2.0 ports) (Supports

•

ESD Protection)

2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports)

•

(ASMedia ASM1074 hub) (Supports ESD Protection)

1 x Front Panel Type C USB 3.2 Gen1 Header (Supports ESD

•

Protection)

English

BIOS Feature

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU Core/Cache, GT, DRAM, VPPM, VCCIN AUX, VCCIO,

•

VCCST, VCCSA Voltage Multi-adjustment

Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water

Hardware Monitor

•

Pump Fans Quiet Fan (Auto adjust chassis fan speed by CPU tempera-

•

ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/

•

Water Pump Fans CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

VPPM, VCCIN AUX, VCCSA, VCCPLL, VCCIO

Microso® Windows® 10 64-bit

Certications

* For detailed product information, please visit our website: http://www.asrock .com

Please realize that the re is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tool s. Overclocking may aect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

B560 Pro4

English

Chapter 2 Installation

is is an ATX form factor motherboard. Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard components. In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components. Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components. When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

2.1 Installing the CPU

1. Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to in sert the CPU into the socket if above situation is found. Otherwise, the CPU will be seriously damaged.

2. Unplug all power cables before in stalling the CPU.

B560 Pro4

English

Please save and replace the cover if the processor i s removed. e cover must be placed if you wish to return the motherboard for aer service.

B560 Pro4

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

CPU_FAN

2.3 Installing Memory Modules (DIMM)

is motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identical (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memor y Technology with only one or three

memory module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

Dual Channel Memory Conguration

Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated 2 Populated Populated Populated Populated

e DIMM only ts in one correct orientation. It will cause permanent damage to the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect orientation.

B560 Pro4

English

2.4 Expansion Slots (PCI Express Slots)

ere are 4 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is switched o or the power cord is unplugged. Plea se read the documentation of the expan sion card and make necessary hardware settings for the card before you start the installation.

PCIe slots:

11th Gen Intel® CoreTM Processors:

PCIE1 (PCIe 4.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x2 lane width graphics cards. PCIE4 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

10th Gen Intel® CoreTM Processors:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards. PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards. PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x2 lane width graphics cards. PCIE4 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

B560 Pro4

PCIe Slot Congurations

PCIE1 PCIE3

11th Gen Intel® CoreTM Processors Gen4x16 Gen3x2

10th Gen Intel® CoreTM Processors Gen3x16 Gen3x2

For a better ther mal environment, please connect a chassi s fan to the motherboard’s chassis fan connector (CHA_ FAN1/WP, CHA_ FA N2/WP, CHA_FAN3/WP, CHA_ FAN4/WP or CHA_ FAN5/WP) when using multiple graphics cards.

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is

“Open”.

Clear CMOS Jumper (CLRMO S1) (see p.1, No. 23)

CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn o the computer and unplug the power cord from the power supply. Aer waiting for 15 seconds, use a jumper cap to short the pins on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right aer you update the BIOS. If you need to clear the CMOS when you just nish updating the BIOS, you must boot up the system rst, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default prole will be cleared only if the CMOS battery is removed. Please remember toremove the jumper cap aer clearing the CMOS.

2-pin Jumper

English

If you clear the CMOS, the case open may be detec ted. Please adjust the BIOS option “Clear Status” to clear the record of previous chassis intrusion status.

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.

B560 Pro4

System Panel Header (9-pi n PANEL1) (see p.1, No. 22)

PWRBTN (Power Button):

Connec t to the power button on the chassis front panel. You may congure the way to turn o your system using the power button.

RESET (Reset Button): Connec t to the reset button on the chassi s front panel. Press the reset button to restar t the computer if the computer freezes and fails to perform a nor mal restart.

PLED (Syste m Power LED): Connec t to the power status indicator on the chassis front panel. e LED i s on when the system is ope rating. e LED keeps blinking when the system i s in S1/S3 sleep state. e LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Ha rd Drive Activity LED): Connec t to the hard drive activity LED on the chassis front panel. e LED is on when the hard drive i s reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists of power button, reset button, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this head er, make sure the wire assig nments and the pin assig nments are matched correctly.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

English

Chassis Intrusion and

USB_PWR

Speaker Header (7-pi n SPK_CI1) (see p.1, No. 25)

DUMMY +5V

SIGNAL

SPEAKER

DUMMY

GND

DUMMY

Please connect the chassis intrusion and the chassis speaker to this header.

Serial ATA3 Connectors Ver tica l: (SATA3_0: see p.1, No. 21) (SATA3_1: see p.1, No. 20)

Right-A ngle: (SATA3_2: see p.1, No. 13) (SATA3_3: see p.1, No. 14) (SATA3_4: see p.1, No. 15) (SATA3_5: see p.1, No. 16)

USB 2.0 Header (9-pin USB3_4) (see p.1, No. 24)

SATA3_0

P-

USB_PWR

SATA3_2

SATA3_3

SATA3_4

SATA3_5

P+

GND

SATA3_1

DUMMY

ese six SATA3 connectors support SATA data cables for internal storage devices with up to

6.0 Gb/s data transfer rate.

* If M2_3 is occupied by a SATA-type M.2 device, SATA3_1 will be disabled.

ere is one USB 2.0 header on this motherboard. is USB 2.0 header can support two ports.

English

B560 Pro4

USB 3.2 Gen1 Headers Ver tica l: (19-pin USB3_5_6) (see p.1, No. 12)

Right-A ngle: (19-pin USB3_7_8) (see p.1, No. 11)

Front Panel Audio Header (9-pin HD_ AUDIO1) (see p.1, No. 31)

1. High De nition Audio supports Jack Sen sing, but the panel wire on the chassis

must support HDA to function correctly. Please follow the instructions in our manual and chassis manual to install your system.

2. If you use an AC’97 audio panel , please install it to the front panel audio header by

the steps below: A. Connect Mic_IN (MIC) to MIC2_ L. B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L. C. Connect Ground (GND) to Ground (GND). D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel. E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

Dummy

IntA_PB_D+

IntA_PB_D-

GND

IntA_PB_SSTX+

IntA_PB_SSTX-

GND

IntA_PB_SSRX+

IntA_PB_SSRX-

VbusV

GND

MIC2_L

PRESENCE#

MIC_RET

J_SENSE

OUT2_R

MIC2_R

VbusVbus

IntA_PB_SSRX-

IntA_PB_SSRX+

GND

IntA_PB_SSTX-

IntA_PB_SSTX+

GND

IntA_PB_D-

IntA_PB_D+

Dummy

IntA_PA_D+

IntA_PA_D-

GND

IntA_PA_SSTX+

IntA_PA_SSTX-

GND

IntA_PA_SSRX+

IntA_PA_SSRX-

Vbus

OUT_RET

OUT2_L

ere are two headers on this motherboard. Each USB 3.2 Gen1 header can support two ports.

is header is for connecting audio devices to the front audio panel.

English

Chassis/Water Pump Fan

4 3 2 1

FAN_VOLTAGE

Connectors (4-pin CHA_FAN1/WP) (see p.1, No. 32)

(4-pin CHA_FAN2/WP) (see p.1, No. 26) (4-pin CHA_FAN3/WP) (see p.1, No. 27)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

GND

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

is motherboard provides ve 4-Pin water cooling

chassis fan connectors. If

you plan to connect a 3-Pin

chassis water cooler fan, please connect it to Pin 1-3.

English

(4-pin CHA_FAN4/WP) (see p.1, No. 17)

(4-pin CHA_FAN5/WP) (see p.1, No. 8)

CPU Fan Connector (4-pin CPU_FAN1) (see p.1, No. 4)

CPU/Water Pump Fan Connector (4-pin CPU_FAN2/WP) (see p.1, No. 5)

ATX Power Connector (24-pin ATXPWR1) (see p.1, No. 9)

FAN_SPEED_CONTROL

FAN_SPEED

FAN_VOLTAGE

FAN_SPEED_CONTROL

CPU_FAN_SPEED

+12V

GND

CPU_FAN_SPEED

GND

FAN_SPEED_CONTROL

GND

FAN_VOLTAGE

FAN_SPEED

GND

1234

is motherboard provides a 4-Pin CPU fan (Quiet Fan) connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3.

is motherboard provides a 4-Pin water cooling CPU fan connector. If you plan to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.

is motherboard provides a 24-pin ATX power connector. To use a 20-pin ATX power supply, please plug it along Pin 1 and Pin

13.

B560 Pro4

8 5

ATX 12V Power Connector (8-pin ATX12V1) (see p.1, No. 1)

Front Panel Type C USB

3.2 Gen1 Header (20-pin USB31_TC_1) (see p.1, No. 10)

Serial Port Header (9-pin COM1) (see p.1, No. 30)

USB Type-C Cable

RRXD1

DDTR#1

DDSR#1

CCTS#1

GND

TTXD1

DDCD#1

RRI#1

RRTS#1

is motherboard provides an 8-pin ATX 12V power connector. To use a 4-pin

ATX power supply, please plug it along Pin 1 and Pin

*Warning: Please make

sure that the power cable

connected is for the CPU

and not the graphics card.

Do not plug the PCIe pow-

er cable to this connector.

ere is one Front Panel Type C USB 3.2 Gen1 Header on this motherboard. is header is used for connecting a USB 3.2 Gen1 module for additional USB 3.2 Gen1 ports.

is COM1 header supports a serial port module.

SPI TPM Header (13 -pi n SPI_TPM _J1) (see p.1, No. 19)

SPI_DQ3

SPI_DQ2

+3.3V

TPM_Present

SPI_MISO

SPI_CS0

CLK

SPI_MOSI

GND

RSMRST#

RST#

TPM_PIRQ

SPI_TPM_CS#

is connector supports SPI Trusted Platform Module (TPM) system, which can securely store keys, digital certicates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity.

English

RGB LED Headers (4-pin RGB_LED1) (see p.1, No. 29)

(4-pi n RGB _LED2) (see p.1, No. 7)

12V GR B

12V

RGB headers are used to connect RGB LED extension cables which allow users to choose from various LED lighting eects.

Caution: Never install the

RGB LED cable in the wrong

orientation; otherwise, the cable

may be damaged.

*Please refer to page 37 for further instructions on this header.

English

Addressable LED Headers (3-pin A DDR_LED1) (see p.1, No. 28)

(3-pin A DDR_LED2) (see p.1, No.6)

VOUT

DO_ADDR

GND

ese headers are used to connect Addressable

LED extension cables which allow users to choose from various LED lighting eects.

Caution: Never install the Ad-

dressable LED cable in the wrong

orientation; otherwise, the cable

may be damaged.

*Please refer to page 38 for further instructions on this header.

2.7 Post Status Checker

Post Status Checker (PSC) diagnoses the computer when users power on the machine. It emits a red light to indicate whether the CPU, memory, VGA or storage is dysfunctional. e lights go o if the four mentioned above are functioning normally.

B560 Pro4

English

2.8 M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT) Installation Guide

e M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket (Key E) supports type 2230 WiFi/BT module and Intel® CNVi (Integrated WiFi/BT). * e M.2 socket does not support SATA M.2 SSDs.

Before you install Intel® Integrated Connectivity (CNVi) module, be sure to turn o the AC power.

Installing the WiFi/BT module

Step 1

Prepare a type 2230 WiFi/BT module or Intel® CNVi (Integrated WiFi/BT) and the screw.

Step 2

Find the nut location to be used.

English

PCB Length: 3cm Module Type: Type2230

+ 162 hidden pages

Asrock B560 Pro4 Quick Installation Guide

Specifications and Main Features

Frequently Asked Questions

User Manual