Asrock B365M-HDV Quick Installation Guide

Version 1.0
Published February 2018
Copyright©2018 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identication or explanation and to the owners’ benet, without intent to

infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or tness for a particular
purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of prots, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage caused by our
goods. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure. If
you require assistance please call ASRock Tel : [phone] ext.123 (Standard
International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Motherboard Layout

Intel

B360

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

ATXPWR1

PCIE2

Top:
RJ-45

HDLED RESET

PLED PWRBTN

PANEL1

1

1

SPK_CI1

COM1

1

B360M-HDV

12

9

7

10

8

15

18

16

20

USB 3.1 Gen2
T: USB5
B: USB6

1

3

2

CMOS

Battery

5

CPU_FAN1

13

1

TPMS1

Top:

LINE I N

Cent er:

FRON T

Bott om:

MIC IN

CHA_FAN2/WP

PCIE3

DVI1

VGA1

USB_13_14

1

SATA3_5

SATA3_4

SATA3_0

SATA3_1

SATA3_2

SATA3_3

HDMI1

1

LPT1

BIOS
ROM

21

19

RoHS

ATX12V1

6

PCIE1

4

CHA_FAN1/WP

14

1

HD_AUDIO1

22

USB 3.1 Gen2
T: USB3
B: USB4

LAN

AUDIO
CODEC

USB 2. 0

T: USB1

B: USB 2

PS2

Keyb oard

/Mou se

M2_ 1

CT2CT3CT4CT1

CLRMOS1

1

11

17

USB_7_8

1

1

USB_11_ 12

Ultra M.2

PCIe Gen3x4

B360M-HDV

English

1

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 Chassis/Water Pump Fan Connector (CHA_FAN1/WP)

5 ATX Power Connector (ATXPWR1)

6 USB 3.1 Gen1 Header (USB_11_12)

7 SATA3 Connector (SATA3_5)

8 SATA3 Connector (SATA3_4)

9 SATA3 Connector (SATA3_2)

10 SATA3 Connector (SATA3_3)

11 Clear CMOS Jumper (CLRMOS1)

12 SATA3 Connector (SATA3_0)

13 SATA3 Connector (SATA3_1)

14 Chassis/Water Pump Fan Connector (CHA_FAN2/WP)

15 System Panel Header (PANEL1)

16 Chassis Intrusion and Speaker Header (SPK_CI1)

17 USB 2.0 Header (USB_7_8)

18 USB 2.0 Header (USB_13_14)

19 COM Port Header (COM1)

20 Print Port Header (LPT1)

21 TPM Header (TPMS1)

22 Front Panel Audio Header (HD_AUDIO1)

English

2

1.4 I/O Panel

1 2 3

B360M-HDV

4

5

11

No. Description No. Description

1 USB 2.0 Ports (USB12) 7 USB 3.1 Gen2 Ports (USB5_6)

2 D-Sub Port 8 USB 3.1 Gen2 Ports (USB_3_4)

3 LAN RJ-45 Port* 9 HDMI Port

4 Line In (Light Blue)** 10 DVI-D Port

5 Front Speaker (Lime)** 11 PS/2 Keyboard/Mouse Port

6 Microphone (Pink)**

* ere are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Por t

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

10

8

79

6

English

3

** To congure 7.1 CH HD Audio, it i s required to use an HD front panel audio module and enable the multi­channel audio feature through the audio driver.

Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Ports in 7.1-channel Conguration:

English

4

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

Chapter 1 Introduction

ank you for purchasing ASRock B360M-HDV motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.

Becau se the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any modi­cations of this documentation occur, the updated version will be availabl e on ASRock’s
website w ithout further notice. If you require technical support related to this mother­board, please visit our website for specic information about the model you are using. You
may nd the l atest VGA cards and CPU suppor t list on ASRock’s website a s well. ASRock
website http://www.asrock.com.

1.1 Package Contents

ASRock B360M-HDV Motherboard (Micro ATX Form Factor)

•

ASRock B360M-HDV Quick Installation Guide

•

ASRock B360M-HDV Support CD

•

1 x I/O Panel Shield

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x Screw for M.2 Socket (Optiona l)

•

B360M-HDV

English

5

1.2 Specications

Platform

CPU

Chipset

Memory

Expansion
Slot

•

•

•

•

•

•

•

•

•

•

•

•

* Supports NVMe SSD as boot disks

•

Micro ATX Form Factor
Solid Capacitor design

Supports 8th Generation Intel® CoreTM Processors (Socket

1151)
Supports Intel® Turbo Boost 2.0 Technology

Intel® B360

Dual Channel DDR4 Memory Technology
2 x DDR4 DIMM Slots
Supports DDR4 2666/2400/2133 non-ECC, un-buered
memory
Max. capacity of system memory: 32GB
Supports Intel® Extreme Memory Prole (XMP) 2.0
15μ Gold Contact in DIMM Slots

1 x PCI Express 3.0 x16 Slot (PCIE1: x16 mode)*

2 x PCI Express 3.0 x1 Slots (Flexible PCIe)

English

6

Graphics

Intel® UHD Graphics Built-in Visuals and the VGA outputs

•

can be supported only with processors which are GPU
integrated.
Supports Intel® UHD Graphics Built-in Visuals : Intel®

•

Quick Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® UHD Graphics
DirectX 12

•

HWAEncode/Decode: AVC/H.264, HEVC/H.265 8-bit,

•

HEVC/H.265 10-bit, VP8, VP9 8-bit, VP9 10-bit (Decode
only), MPEG2, MJPEG, VC-1 (Decode only)

Audio

B360M-HDV

ree graphics output options: D-Sub, DVI-D and HDMI

•

Supports HDMI with max. resolution up to 4K x 2K

•

(4096x2160) @ 30Hz
Supports DVI-D with max. resolution up to 1920x1200 @

•

60Hz
Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
Supports HDCP with DVI-D and HDMI Ports

•

Supports 4K Ultra HD (UHD) playback with HDMI Port

•

7.1 CH HD Audio (Realtek ALC887 Audio Codec)

•

* To congure 7.1 CH HD Audio, it is required to use an HD
front panel audio module and enable the multi-channel audio
feature through the audio driver.

Supports Surge Protection

•

ELNA Audio Caps

•

LAN

Rear Panel
I/O

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection

•

Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

2 x USB 2.0 Ports (Supports ESD Protection)

•

4 x USB 3.1 Gen2 Type-A Ports (10 Gb/s)

•

1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LE D)
HD Audio Jacks: Line in / Front Speaker / Microphone

•

English

7

Storage

Connector

6 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and

•

Hot Plug*
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_3 will
be disabled.

1 x Ultra M.2 Socket (M2_1), supports M Key type

•

2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2

PCI Express module up to Gen3 x4 (32 Gb/s)**
** Supports Intel® OptaneTM Tech nolo gy
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit

1 x Print Port Header

•

1 x COM Port Header

•

1 x TPM Header

•

1 x Chassis Intrusion and Speaker Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.

2 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan

•

Speed Control)
* e Chassis/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
* CHA_FAN1/WP and CHA_FAN2/WP can auto detect if 3-pin
or 4-pin fan is in use.

1 x 24 pin ATX Power Connector

•

1 x 8 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports

•

ESD Protection)

1 x USB 3.1 Gen1 Header (Supports 2 USB 3.1 Gen1 ports)

•

(Supports ESD Protection)

English

8

BIOS
Feature

Hardware
Monitor

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU, GT_CPU, DRAM, PCH 1.05V Voltage Multi-adjust-

•

ment

Temperature Sensing: CPU, Chassis/Water Pump Fans

•

Fan Tachometer: CPU, Chassis/Water Pump Fans

•

Quiet Fan (Auto adjust chassis fan speed by CPU

•

temperature): CPU, Chassis/Water Pump Fans
Fan Multi-Speed Control: CPU, Chassis/Water Pump Fans

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

PCH 1.05V

Microso® Windows® 10 64-bit

OS

Certica­tions

* For detailed product information, please visit our website: http://www.asrock .com

Please realiz e that the re is a certain r isk involved with o verclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technolog y, or using third-party
overclocking to ols. O verclocking may aect your system’s stability, or even c ause damage to
the components and devices of your system. It should be don e at your ow n risk and expense.
We are not responsibl e for possible damage caused by o verclocking.

•

FCC, CE

•

ErP/EuP ready (ErP/EuP ready power supply is required)

•

B360M-HDV

English

9

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components
or change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or

•

in the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-

•

tighten the screws! Doing so may damage the motherboard.

English

10

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into the socket, ple ase check if the P nP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the sock et. Do not
force to in sert the CPU into the socket if above situation is found . Otherwise, the CPU
will be seriously damaged.

2. Unplug all power c ables before in stalling the CPU.

1

B360M-HDV

A

B

2

English

11

3

4

English

12

5

B360M-HDV

Please save and replace the cover if the processor i s removed. e cover must be placed if
you wish to return the motherboard for aer service.

13

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

14

FAN

CPU_

B360M-HDV

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.

1. For dual channel cong uration , you always need to in stall identical (the same

brand, speed , size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Du al Channel Memory Technology with only one memory

module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4

slot; otherwise, this motherboard and DIMM may be damaged.

e DIMM only ts in one correct orie ntation. It will cause permanent dam age to
the mothe rboard and the DIMM if you force the DIMM into the slot at incor rect
orientation.

15

English

1

2

English

16

3

B360M-HDV

2.4 Expansion Slots (PCI Express Slots)

ere are 3 PCI Express slots on the motherboard.

Before installing an ex pansion card, please make sure that the power supply is
switched o or the power cord is unplugged. Plea se read the documentation of the
expan sion card and mak e necessary h ardware settings for the card before you start
the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE2 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

17

English

2.5 Jumpers Setup

e illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is
“Open”.

English

Clear CMOS Jumper
(C LRC MO S1)
(see p.1, No. 11)

CLRCMOS1 allows you to clear the data in CMOS. e data in CMOS includes
system setup information such as system password, date, time, and system setup
parameters. To clear and reset the system parameters to default setup, please
turn o the computer and unplug the power cord, then use a jumper cap to short
the pins on CLRCMOS1 for 3 seconds. Please remember to remove the jumper
cap aer clearing the CMOS. If you need to clear the CMOS when you just nish
updating the BIOS, you must boot up the system rst, and then shut it down
before you do the clear-CMOS action.

If you clear the CMOS, the case open may be detec ted. Please a djust the BIOS option
“Clear Status” to clear the record of previou s chassis int rusion status.

2-pin Jumper

Short: Clear CMOS
Open: Default

18

2.6 Onboard Headers and Connectors

1

Onboard headers and connectors are NOT jump ers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.

B360M-HDV

System Panel Header
(9-pi n PANEL1)
(see p.1, No. 15)

PWRBTN (Power Button):

Connec t to the power button on the ch assi s front panel. You may congure the way to tur n
o your system using the power button.

RESET (Reset B utton):
Connec t to the reset button on the chassi s front panel. P ress the reset button to re start the
computer if the computer f reezes and fails to per form a normal restar t.

PLED (Syste m Power LED):
Connec t to the power status indicator on the chas sis front panel. e LED i s on when the
system is operating. e LED keeps blinking wh en the system is in S1/S3 sleep state. e
LED is o when the system is in S4 slee p state or powered o (S5).

HDLED (Ha rd Drive Activity LED):
Connec t to the hard drive ac tivity LED on the chassis front panel. e LED is on when the
hard drive is reading or wr iting data.

e front panel de sign may dier by chassis. A front panel module mainly consists of powe r
button, reset button , power LED, hard dr ive activity LED, speaker and etc. When connect­ing your ch assi s front panel module to thi s header, make sure the wire a ssignments and the
pin assignments are matched correctly.

PLED+

PLED-

HDLED-

HDLED+

PWRBTN#

GND

RESET#

GND

GND

Connect the power
button, reset button and
system status indicator on
the chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting
the cables.

English

19

Chassis Intrusion and

1

+5V

DUMMY

SIGNAL

GND

DUMMY

SPEAKER

DUMMY

IntA_P3_SSTX+

IntA_P3_SSRX+

IntA_P2_SSRX+

IntA_P2_SSTX+

DUMMY

GND

GND

P+

P-

USB_PWR

P+

P-

USB_PWR

1

Speaker Header
(7-pi n SPK_CI1)
(see p.1, No. 16)

Please connect the
chassis power LED and
the chassis speaker to this
header.

English

Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 12)
(SATA3_1:
see p.1, No. 13)
(SATA3_2:
see p.1, No. 9)
(SATA3_3:
see p.1, No. 10)
(SATA3_4:
see p.1, No. 8)
(SATA3_5:
see p.1, No. 7)

USB 2.0 Headers
(9-pin USB_7_8)
(see p.1, No. 17)
(9-pin USB_13_14)
(see p.1, No. 18)

USB 3.1 Gen1 Header
(19-pin USB_11_12)
(see p.1, No. 6)

Vbus

IntA_P2_SSRX-

IntA_P2_SSTX-

IntA_P2_D-

IntA_P2_D+

SATA3_5

SATA3_2

SATA3_0

GND

GND

VbusVbus

IntA_P3_SSRX-

GND

IntA_P3_SSTX-

GND

IntA_P3_D-

IntA_P3_D+

ID

1

SATA3_4

SATA3_3

SATA3_1

ese six SATA3
connectors support SATA
data cables for internal
storage devices with up to

6.0 Gb/s data transfer rate.
* If M2_1 is occupied by
a SATA-type M.2 device,
SATA3_3 will be disabled.

ere are two USB

2.0 headers on this
motherboard. Each USB

2.0 header can support
two ports.

ere is one header on
this motherboard. is
USB 3.1 Gen1 header can
support two ports.

20

B360M-HDV

J_SENSE

OUT2_L

1

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

FAN_SPEED_CONTROL

4

FAN_SPEED_CONTROL

1 2 3 4

GND

1 2 3 4

Front Panel Audio Header
(9-pin HD_ AUDIO1)
(see p.1, No. 22)

1. High Denition Audio support s Jack Sensing, but the panel wire on the cha ssis

must support HDA to function cor rectly. Please follow the instr uctions in our
manual and chassis manual to in stall your system.

2. If you use an AC’97 audio panel , please install it to th e front panel audio header by

the steps below:
A. Connect Mic_IN (MIC) to MIC2_ L.
B. Conne ct Audio_R (RIN) to OUT2_R and Audio_ L (LIN) to OUT2_ L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_ RET and OUT_RET are for the HD audio panel only. You don’t need to
connec t them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.

Chassis/Water Pump Fan
Connectors
(4-pin CHA_FAN1/WP)
(see p.1, No. 4)

(4-pin CHA_FAN2/WP)
(see p.1, No. 14)

FAN_VOLTAGE

FAN_SPEED

FAN_SPEED_CONTROL

CHA_FAN_SPEED

FAN_VOLTAGE

GND

is header is for
connecting audio devices
to the front audio panel.

is motherboard
provides two 4-Pin water
cooling

chassis

fan
connectors. If you plan to
connect a 3-Pin

3
2
1

water cooler fan, please
connect it to Pin 1-3.

chassis

CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 2)

CPU_FAN_SPEED

FAN_VOLTAGE

GND

is motherboard
provides a 4-Pin CPU fan
(Quiet Fan) connector.
If you plan to connect a
3-Pin CPU fan, please
connect it to Pin 1-3.

English

21

ATX Power Connector

1

GN

D

#

GN D

5

1

8

1

1

AFD#

SLCT

(24-pin ATXPWR1)
(see p.1, No. 5)

24

12

is motherboard
provides a 24-pin ATX
power connector. To use a
20-pin ATX power supply,
please plug it along Pin 1

1

13

and Pin 13.

English

ATX 12V Power
Connector
(8-pin ATX12V1)
(see p.1, No. 1)

Serial Port Header
(9-pin COM1)
(see p.1, No. 19)

TPM Header
(17-pi n TPMS1)
(see p.1, No. 21)

Print Port Header
(25-pin LPT1)
(see p.1, No. 20)

STB#

ERROR#

PINIT#

SPD1

SPD0

SLIN#

SPD2

+3V S B

SER IRQ #

SPD3

RRXD1

DDTR#1

TTXD1

DDCD#1

S_P WRDW N #

SPD5

SPD4

DDSR#1

GND

LAD 0

GN D

SPD6

CCTS#1

RRTS#1

+3 V

LAD 1

GND

SPD7

LAD 3

LAD 2

RRI#1

PC IRS T

SMB _DAT A_M AIN

ACK#

BUSY

is motherboard
provides an 8-pin ATX
12V power connector. To
use a 4-pin ATX power
supply, please plug it along
Pin 1 and Pin 5.

is COM1 header
supports a serial port
module.

is connector supports Trusted
Platform Module (TPM) system,

PC ICL K

FRA M E

which can securely store keys,

GN D

digital certicates, passwords,
and data. A TPM system also
helps enhance network security,

SMB _CLK _MA IN

protects digital identities, and
ensures platform integrity.

is is an interface
for print port cable
that allows convenient

PE

connection of printer
devices.

22

B360M-HDV

4

2.7 M.2_SSD (NGFF) Module Installation Guide

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. e M.2 Socket
(M2_1) supports SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen2 x2 (10
Gb/s).
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_3 will be disabled.

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module
and the screw.

Step 2

3

2

1

Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, nd the corresponding nut
location to be used.

A

BCD

No. 1 2 3 4

Nut Location A B C D

PCB Length 3cm 4.2cm 6cm 8cm

Module Type Type223 0 Ty pe 224 2 Type2 260 Ty pe 2280

English

23

Step 3

Move the stando based on the
module type and length.

A

BCD

e stando is placed at the nut
location D by default. Skip Step 3
and 4 and go straight to Step 5 if you
are going to use the default nut.
Otherwise, release the stando by
hand.

Step 4

Peel o the yellow protective lm on
the nut to be used. Hand tighten the

A

BCD

stando into the desired nut location
on the motherboard.

Step 5

Gently insert the M.2 (NGFF) SSD
module into the M.2 slot. Please
be aware that the M.2 (NGFF) SSD

ABCD

module only ts in one orientation.

English

24

o

ABCD

20

Step 6

Tighten the screw with a screwdriver
to secure the module into place.

NUT1NUT2D

Please do not overtighten the screw
as this might damage the module.

M.2_SSD (NGFF) Module Support List

Vendor Interface P/ N

ADATA SATA3 AXNS381E-128GM-B
ADATA SATA3 AX NS381E-256 GM-B
ADATA SATA3 ASU800NS38-256GT-C
ADATA SATA3 ASU800NS38-512GT-C
ADATA PCIe3 x4 ASX7000NP-128GT-C
ADATA PCIe3 x4 ASX8000NP-256GM-C
ADATA PCIe3 x4 ASX7000NP-256GT-C
ADATA PCIe3 x4 ASX8000NP-512GM-C
ADATA PCIe3 x4 ASX7000NP-512GT-C
Apacer PCIe3 x4 AP240GZ280
Corsair PCIe3 x4 CSSD-F240GBMP500
Crucial SATA3 CT120M500SSD4
Crucial SATA3 CT240M500SSD4
Intel SATA3 Intel SSDSCKGW080A401/80G
Intel PCIe3 x4 SSDPEKKF256G7
Intel PCIe3 x4 SSDPEKK F512G7
Kingston SATA3 SM2280S3
Kingston PCIe3 x4 SKC1000/480G
Kingston PCIe2 x4 SH2280S3/480G
OCZ PCIe3 x4 RVD400-M2280-512G (NVME)
PAT RI OT PCIe3 x4 PH240GPM280SSDR NVME
Plextor PCIe3 x4 PX-128M8PeG
Plextor PCIe3 x4 PX-1TM 8PeG
Plextor PCIe3 x4 PX-256M8PeG
Plextor PCIe3 x4 PX-512M8Pe G
Plextor PCIe PX-G25 6M6e
Plextor PCIe PX-G512M6e
Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM)
Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME)
Samsung PCIe3 x4 SM951 (NVME)
Samsung PCIe3 x4 SM951 (MZHPV256HDGL)
Samsung PCIe3 x4 SM951 (MZHPV512HDGL)
Samsung PCIe3 x4 SM951 (NVME)
Samsung PCIe x4 XP941-512G (MZHPU512HCGL)
SanDisk PCIe SD6PP4 M-128G
SanDisk PCIe SD6PP4M-256G
Te am SATA3 TM4PS4128GMC105
Te am SATA3 TM4 PS4256GMC105
Te am SATA3 TM8PS4128GMC105
Te am SATA3 TM8PS4256GMC105
TEAM PCIe3 x4 TM8FP2240G0C101

B360M-HDV

English

25

TEAM PCIe3 x4 TM8FP2480GC110
Tra nscend SATA3 TS256GMTS400
Tra nscend SATA3 TS512GMTS600
Tra nscend SATA3 TS512GMTS800
V- Col or SATA 3 VLM100-120G-2280B-RD
V- Col or SATA 3 VLM10 0-240G -2280RGB
V- Col or SATA 3 VSM100 -240G-228 0
V- Col or SATA 3 VLM10 0-240G -2280B-RD
WD SATA3 WDS100T1B0B-00AS40
WD SATA3 WDS240G1G0B-00RC30
WD PCIe3 x4 WDS256G1X0C-00ENX0 (NVME)
WD PCIe3 x4 WDS512G1X0C-0 0ENX0 (NVME)

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com

English

26

1 Einleitung

Vielen Dank, dass Sie sich für das B360M-HDV von ASRock entschieden haben – ein
zuverlässiges Motherboard, das konsequent unter der strengen Qualitätskontrolle von
ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design,
das ASRock Streben nach Qualität und Beständigkeit erfüllt.

Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert werden
können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert werden. Falls
diese Dokumentation irgendwelchen Änderungen unterliegt, wird die aktualisierte Version
ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung gestellt. Sollten Sie technische
Hilfe in Bezug auf dieses Motherboard benötigen, erhalten Sie auf unserer Webseite spezischen
Informationen über das von Ihnen verwendete Modell. Auch nden Sie eine aktuelle Liste
unterstützter VGA-Karten und Prozessoren auf der ASRock-Webseite: ASRock-Webseite
http://www.asrock.com.

1.1 Lieferumfang

ASRock B360M-HDV-Motherboard (Micro-ATX-Formfaktor)

•

ASRock B360M-HDV-Schnellinstallationsanleitung

•

ASRock B360M-HDV-Support-CD

•

1 x E/A-Blendenabschirmung

•

2 x Serial-ATA- (SATA) Datenkabel (optional)

•

1 x Schraube für M.2-Sockel (optional)

•

B360M-HDV

27

Deutsch

1.2 Technische Daten

Micro-ATX-Formfaktor

Plattform

•

Feststoondensator-Design

•

Deutsch

Prozessor

Chipsatz

Speicher

Erweiter­ungssteck­platz

Grakkarte

Unterstützt Intel® CoreTM-Prozessoren (Sockel 1151) der 8

•

Generation
Unterstützt Intel® Turbo Boost 2.0-Technologie

•

Intel® B360

•

Dualkanal-DDR4-Speichertechnologie

•

2 x DDR4-DIMM-Steckplätze

•

Unterstützt ungepuerten DDR4-2666/2400/2133-Non-ECC-

•

Speicher
Systemspeicher, max. Kapazität: 32 GB

•

Unterstützt Intel® Extreme Memory Prole (XMP) 2.0

•

15-μ-Goldkontakt in DIMM-Steckplätze

•

1 x PCI-Express 3.0-x16-Steckplatz (PCIE1:x16-Modus)*

•

* Unterstützt NVMe-SSD als Bootplatte

2 x PCI-Express 3.0-x1-Steckplätze (Flexible PCIe)

•

Integrierte Intel® UHD Graphics-Visualisierung und VGA-

•

Ausgänge können nur mit Prozessoren unterstützt werden, die
GPU-integriert sind.
Unterstützt integrierte Intel® UHD Graphics-Visualisierung:

•

Intel® Quick Sync Video mit AVC, MVC (S3D) und MPEG­2 Full HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® UHD Graphics
DirectX 12

•

HWA encodieren/decodieren: AVC/H.264, HEVC/H.265

•

8 bit, HEVC/H.265 10 bit, VP8, VP9 8 bit, VP9 10 bit (nur
Dekodierung), MPEG2, MJPEG, VC-1 (nur Dekodierung)
Drei Grakkarten-Ausgangsoptionen: D-Sub, DVI-D und HDMI

•

ten

28