Asrock B250M-HDV Quick Installation Guide

Version 1.0
Published October 2016
Copyright©2016 ASRock INC. All rights reserved.

Copyright Notice:

No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.

Products and corporate names appearing in this documentation may or may not be
registered trademarks or copyrights of their respective companies, and are used only

for identication or explanation and to the owners’ benet, without intent to infringe.

Disclaimer:

Specications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for any
errors or omissions that may appear in this documentation.

With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to the
implied warranties or conditions of merchantability or tness for a particular purpose.

In no event shall ASRock, its directors, ocers, employees, or agents be liable for any
indirect, special, incidental, or consequential damages (including damages for loss
of prots, loss of business, loss of data, interruption of business and the like), even if
ASRock has been advised of the possibility of such damages arising from any defect or
error in the documentation or product.

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause

undesired operation.

CALIFORNIA, USA ONLY

e Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the Cali­fornia Legislature. When you discard the Lithium battery in California, USA, please follow
the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/per­chlorate”

ASRock Website: http://www.asrock.com

AUSTRALIA ONLY

Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure. If you require assistance please call ASRock Tel : +886-2­28965588 ext.123 (Standard International call charges apply)

e terms HDMI™ and HDMI High-Denition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.

Motherboard Layout

Intel

B250

ATXP WR 1

HDLED R ESET

PLED P WRBTN

PANEL1

1

COM1

1

B250M-HDV

RoH S

CPU_FAN1

PCIE1

TPMS1

1

1

PCIE2

Fro nt USB 3. 0

CMO S

Bat tery

DDR 4_B1 (6 4 bit, 28 8-pin m odule )

DDR 4_A1 (6 4 bit, 28 8-pin m odule )

SATA3_4

SATA3_5

USB3_5 _6

SATA3_2

SATA3_3

1

HD_AUDIO 1

M2_1

CT3CT4 CT2

Top:
RJ-4 5

USB 3 .0
T: USB3
B: US B4

HDM I1

Top:

LINE IN

Cente r:

FRONT

Botto m:

MIC IN

PCI E xpres s 3.0

SATA3_0

CHA_FAN 2

Ultr a M.2

PCIe G en3 x4

VGA 1

USB 3.0
T:U SB1
B: USB2

Ct1

1

LPT1

USB_3_4

1

BIOS
ROM

SATA3_1

Optan e Re ad y

PCIE3

1

SPEAKER1

CI1

1

USB_5_6

1

CHA_FAN1

CLRMOS1

ATX12V1

USB 2. 0

T: USB1

B: USB 2

PS2

Keyb oard

/Mou se

DVI 1

B250M-HDV

English

1

No. Description

1 ATX 12V Power Connector (ATX12V1)

2 CPU Fan Connector (CPU_FAN1)

3 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)

4 ATX Power Connector (ATXPWR1)

5 USB 3.0 Header (USB3_5_6)

6 USB 2.0 Header (USB_5_6)

7 SATA3 Connector (SATA3_4)

8 SATA3 Connector (SATA3_5)

9 SATA3 Connector (SATA3_3)

10 SATA3 Connector (SATA3_2)

11 System Panel Header (PANEL1)

12 Chassis Fan Connector (CHA_FAN2)

13 Chassis Speaker Header (SPEAKER1)

14 SATA3 Connector (SATA3_1)

15 SATA3 Connector (SATA3_0)

16 Chassis Intrusion Header (CI1)

17 TPM Header (TPMS1)

18 USB 2.0 Header (USB_3_4)

19 Print Port Header (LPT1)

20 COM Port Header (COM1)

21 Front Panel Audio Header (HD_AUDIO1)

22 Chassis Fan Connector (CHA_FAN1)

English

2

I/O Panel

1 2

B250M-HDV

3

4

11 569

10

78

No. Description No. Description

1 USB 2.0 Ports (USB_12) 7 USB 3.0 Ports (USB3_1_2)

2 LAN RJ-45 Port* 8 HDMI Port

3 Line In (Light Blue)** 9 D-Sub Port

4 Front Speaker (Lime)** 10 DVI-D Port

5 Microphone (Pink)** 11 PS/2 Keyboard/Mouse Port

6 USB 3.0 Ports (USB3_34)

* ere are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.

ACT/LINK LED

SPEED LED

LAN Port

Activity / Link LED Speed LED

Status Description Status Description

O No Link O 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection

English

3

** To congure 7.1 CH HD Audio, it is required to use an HD front panel audio module and enable the multi-channel
audio feature through the audio driver.

Please set Speaker Conguration to “7.1 Speaker”in the Realtek HD Audio Manager.

Function of the Audio Ports in 7.1-channel Conguration:

English

4

Port Function

Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out

Chapter 1 Introduction

ank you for purchasing ASRock B250M-HDV motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.

Because the motherboard specications and the BIOS soware might be updated, the
content of this documentation will be subject to change without notice. In case any
modications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to this
motherboard, please visit our website for specic information about the model you are
using. You may nd the latest VGA cards and CPU support list on ASRock’s website as
well. ASRock website http://www.asrock.com.

1.1 Package Contents

ASRock B250M-HDV Motherboard (Micro ATX Form Factor)

•

ASRock B250M-HDV Quick Installation Guide

•

ASRock B250M-HDV Support CD

•

2 x Serial ATA (SATA) Data Cables (Optional)

•

1 x Screw for M.2 Socket (Optional)

•

1 x I/O Panel Shield

•

B250M-HDV

English

5

1.2 Specications

Platform

CPU

Chipset

Memory

•

•

•

•

•

•

•

•

•

•

* 7th Gen Intel® CPU supports DDR4 up to 2400; 6th Gen Intel®
CPU supports DDR4 up to 2133.

•

•

•

•

Micro ATX Form Factor
Solid Capacitor design

Supports 7th and 6th Generation Intel® CoreTM i7/i5/i3/
Pentium®/Celeron® Processors (Socket 1151)
Digi Power design
5 Power Phase design
Supports Intel® Turbo Boost 2.0 Technology

Intel® B250

Dual Channel DDR4 Memory Technology
2 x DDR4 DIMM Slots
Supports DDR4 2400/2133 non-ECC, un-buered memory*

Supports ECC UDIMM memory modules (operate in non­ECC mode)
Max. capacity of system memory: 32GB
Supports Intel® Extreme Memory Prole (XMP) 2.0
15μ Gold Contact in DIMM Slots

English

6

Expansion
Slot

Graphics

1 x PCI Express 3.0 x16 Slot (PCIE1: x16 mode)*

•

* Supports NVMe SSD as boot disks

2 x PCI Express 3.0 x1 Slots (Flexible PCIe)

•

Intel® HD Graphics Built-in Visuals and the VGA outputs can

•

be supported only with processors which are GPU integrated.
Supports Intel® HD Graphics Built-in Visuals : Intel® Quick

•

Sync Video with AVC, MVC (S3D) and MPEG-2 Full
HW Encode1, Intel® InTruTM 3D, Intel® Clear Video HD
Technology, Intel® InsiderTM, Intel® HD Graphics
Gen9 LP, DX11.3, DX12

•

HWAEncode/Decode: VP8, HEVC 8b, VP9, HEVC 10b (For

•

7th Gen Intel® CPU)

HWA Encode/Decode: VP8 , HEVC 8b; GPU/SWEncode/

•

Decode: VP9, HEVC 10b (For 6th Gen Intel® CPU)
Max. shared memory 1024MB

•

* e size of maximum shared memory may vary from dierent
operating systems.

ree graphics output options: D-Sub, DVI-D and HDMI

•

Supports Triple Monitor

•

Supports HDMI with max. resolution up to 4K x 2K

•

(4096x2160) @ 24Hz / (3840x2160) @ 30Hz
Supports DVI-D with max. resolution up to 1920x1200 @

•

60Hz
Supports D-Sub with max. resolution up to 1920x1200 @

•

60Hz
Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and

•

HBR (High Bit Rate Audio) with HDMI Port (Compliant
HDMI monitor is required)
Supports HDCP with DVI-D and HDMI Ports

•

Supports Full HD 1080p Blu-ray (BD) playback with DVI-D

•

and HDMI Ports

B250M-HDV

Audio

LAN

7.1 CH HD Audio (Realtek ALC887 Audio Codec)

•

* To congure 7.1 CH HD Audio, it is required to use an HD front
panel audio module and enable the multi-channel audio feature
through the audio driver.

Supports Surge Protection (ASRock Full Spike Protection)

•

ELNA Audio Caps

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Supports Wake-On-LAN

•

Supports Lightning/ESD Protection (ASRock Full Spike Pro-

•

tection)
Supports Energy Ecient Ethernet 802.3az

•

Supports PXE

•

English

7

English

Rear Panel
I/O

Storage

Connector

1 x PS/2 Mouse/Keyboard Port

•

1 x D-Sub Port

•

1 x DVI-D Port

•

1 x HDMI Port

•

2 x USB 2.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))
4 x USB 3.0 Ports (Supports ESD Protection (ASRock Full

•

Spike Protection))
1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED

•

LED)
HD Audio Jacks: Line in / Front Speaker / Microphone

•

6 x SATA3 6.0 Gb/s Connectors, support NCQ, AHCI and Hot

•

Plug*
* If M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will
be disabled.

1 x Ultra M.2 Socket, supports type 2230/2242/2260/2280 M.2

•

SATA3 6.0 Gb/s module and M.2 PCI Express module up to

Gen3 x4 (32 Gb/s)**
** Supports Intel® OptaneTM Technology
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit

1 x Print Port Header

•

1 x COM Port Header

•

1 x TPM Header

•

1 x Chassis Intrusion Header

•

1 x CPU Fan Connector (4-pin)

•

* e CPU Fan Connector supports the CPU fan of maximum 1A
(12W) fan power.

2 x Chassis Fan Connectors (4-pin)

•

1 x 24 pin ATX Power Connector

•

1 x 4 pin 12V Power Connector

•

1 x Front Panel Audio Connector

•

2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD

•

Protection (ASRock Full Spike Protection))

1 x USB 3.0 Header (Supports 2 USB 3.0 ports) (Supports ESD

•

Protection (ASRock Full Spike Protection))

8

BIOS
Feature

Hardware
Monitor

OS

AMI UEFI Legal BIOS with multilingual GUI support

•

ACPI 6.0 Compliant wake up events

•

SMBIOS 2.7 Support

•

CPU, GT_CPU, DRAM, PCH 1.0V Voltage Multi-adjustment

•

CPU/Chassis temperature sensing

•

CPU/Chassis Fan Tachometer

•

CPU/Chassis Quiet Fan (Auto adjust chassis fan speed by

•

CPU temperature)
CPU/Chassis Fan multi-speed control

•

CASE OPEN detection

•

Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,

•

PCH 1.0V

Microso® Windows® 10 64-bit (For 7th Gen Intel® CPU)

•

Microso® Windows® 10 64-bit / 8.1 64-bit / 7 32-bit / 7 64-bit

•

(For 6th Gen Intel® CPU)
* To install Windows® 7 OS, a modied installation disk with
xHCI drivers packed into the ISO le is required. Please refer to
page 141 for more detailed instructions.
* For the updated Windows® 10 driver, please visit ASRock’s web­site for details: http://www.asrock.com

B250M-HDV

FCC, CE, WHQL, RCM, BSMI

Certica-

•

tions

* For detailed product information, please visit our website: http://www.asrock.com

Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using third-party
overclocking tools. Overclocking may aect your system’s stability, or even cause damage
to the components and devices of your system. It should be done at your own risk and
expense. We are not responsible for possible damage caused by overclocking.

English

9

Chapter 2 Installation

is is a Micro ATX form factor motherboard. Before you install the motherboard,
study the conguration of your chassis to ensure that the motherboard ts into it.

Pre-installation Precautions

Take note of the following precautions before you install motherboard components or
change any motherboard settings.

Make sure to unplug the power cord before installing or removing the motherboard

•

components. Failure to do so may cause physical injuries and damages to motherboard
components.
In order to avoid damage from static electricity to the motherboard’s components,

•

NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
Hold components by the edges and do not touch the ICs.

•

Whenever you uninstall any components, place them on a grounded anti-static pad or in

•

the bag that comes with the components.
When placing screws to secure the motherboard to the chassis, please do not over-tighten

•

the screws! Doing so may damage the motherboard.

English

10

2.1 Installing the CPU

1. Before you insert the 1151-Pin CPU into the socket, please check if the PnP cap is on
the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do
not force to insert the CPU into the socket if above situation is found. Otherwise, the
CPU will be seriously damaged.

2. Unplug all power cables before installing the CPU.

1

B250M-HDV

A

B

2

English

11

3

4

English

12

5

Please save and replace the cover if the processor is removed. e cover must be placed if
you wish to return the motherboard for aer service.

B250M-HDV

13

English

2.2 Installing the CPU Fan and Heatsink

1 2

English

14

FAN

CPU_

2.3 Installing Memory Modules (DIMM)

is motherboard provides two 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.

1. For dual channel conguration, you always need to install identical (the same brand,
speed, size and chip-type) DDR4 DIMM pairs.

2. It is unable to activate Dual Channel Memory Technology with only one memory
module installed.

3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot;
otherwise, this motherboard and DIMM may be damaged.

e DIMM only ts in one correct orientation. It will cause permanent damage to the
motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.

B250M-HDV

15

English

1

2

English

16

3

2.4 Expansion Slots (PCI Express Slots)

ere is 1 PCI slot and 3 PCI Express slots on the motherboard.

Before installing an expansion card, please make sure that the power supply is switched
o or the power cord is unplugged. Please read the documentation of the expansion card
and make necessary hardware settings for the card before you start the installation.

PCIe slots:

PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.

B250M-HDV

17

English

2.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors will
cause permanent damage to the motherboard.

System Panel Header
(9-pin PANEL1)
(see p.1, No. 11)

PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may congure the way to
turn o your system using the power switch.

RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart the
computer if the computer freezes and fails to perform a normal restart.

PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. e LED is on when the
system is operating. e LED keeps blinking when the system is in S1/S3 sleep state. e
LED is o when the system is in S4 sleep state or powered o (S5).

HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. e LED is on when
the hard drive is reading or writing data.

e front panel design may dier by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.

GND RES ET#

PWR BTN#

PLE D-

PLE D+

GND

GND

HDL ED-

HDL ED+

1

Connect the power switch,
reset switch and system
status indicator on the
chassis to this header
according to the pin
assignments below. Note
the positive and negative
pins before connecting the
cables.

English

18

B250M-HDV

Serial ATA3 Connectors
(SATA3_0:
see p.1, No. 15)
(SATA3_1:
see p.1, No. 14)
(SATA3_2:
see p.1, No. 10)
(SATA3_3:
see p.1, No. 9)
(SATA3_4:

SATA3_0

see p.1, No. 7)
(SATA3_5:
see p.1, No. 8)

USB 2.0 Headers
(9-pin USB_3_4)
(see p.1, No. 18)

(9-pin USB_5_6)
(see p.1, No. 6)

SATA3_1

USB _PW R

P-

1

P-

USB _PW R

SATA3_4

SATA3_2

P+

P+

GND

GND

DUM MY

ese six SATA3
connectors support SATA
data cables for internal

SATA3_5

storage devices with up to

6.0 Gb/s data transfer rate.
If M2_1 is occupied by a

SATA3_3

SATA-type M.2 device,
SATA3_5 will be disabled.

ere are two headers
on this motherboard.
Each USB 2.0 header can
support two ports.

USB 3.0 Header
(19-pin USB3_5_6)
(see p.1, No. 5)

Vbus

IntA _PA_SS RX-

IntA _PA_SS RX+

GND

IntA _PA_SS TX-

IntA _PA_SS TX+

GND

IntA _PA_D-

IntA _PA_D+

VbusVbus

IntA _PB_S SRX-

IntA _PB_S SRX+

GND

IntA _PB_S STX-

IntA _PB_S STX+

GND

IntA _PB_D -

IntA _PB_D +

Dumm y

1

ere is one header on this
motherboard. Each USB

3.0 header can support two
ports.

English

19

Front Panel Audio Header

GND

FAN_V OLTAGE_ CONTR OL

FAN_S PEED

FAN_S PEED_ CONTR OL

GND

FAN_V OLTAGE_ CONTR OL

FAN_S PEED

FAN_S PEED_ CONTR OL

(9-pin HD_AUDIO1)
(see p.1, No. 21)

1. High Denition Audio supports Jack Sensing, but the panel wire on the chassis must
support HDA to function correctly. Please follow the instructions in our manual and
chassis manual to install your system.

2. If you use an AC’97 audio panel, please install it to the front panel audio header by the
steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and
adjust “Recording Volume”.

1

GND

PRE SENCE #

MIC 2_R

MIC 2_L

MIC _RET

J_S ENSE

OUT 2_R

OUT _RET

OUT 2_L

is header is for
connecting audio devices
to the front audio panel.

English

20

Chassis Speaker Header
(4-pin SPEAKER1)
(see p.1, No. 13)

Chassis Fan Connectors
(4-pin CHA_FAN1)
(see p.1, No. 22)
(4-pin CHA_FAN2)
(see p.1, No. 12)

CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 2)

DUM MY

1

+5V

SPE AKER

DUM MY

Please connect the chassis
speaker to this header.

Please connect fan cables
to the fan connector and
match the black wire to the
ground pin.

is motherboard provides
a 4-Pin CPU fan (Quiet
Fan) connector. If you plan
to connect a 3-Pin CPU
fan, please connect it to Pin
1-3.

B250M-HDV

ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 4)

ATX 12V Power
Connector
(4-pin ATX12V1)
(see p.1, No. 1)

Serial Port Header
(9-pin COM1)
(see p.1, No. 20)

Chassis Intrusion Header
(2-pin CI1)
(see p.1, No. 16)

1

12

1

RRXD 1

DDCD #1

1

DDTR #1

DDSR #1

GND

TTXD 1

Sig na l

CCTS #1

RRTS #1

GND

24

13

is motherboard provides
a 24-pin ATX power con­nector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin

13.

is motherboard
provides an 4-pin ATX
12V power connector.

is COM1 header
supports a serial port
module.

RRI# 1

is motherboard supports
CASE OPEN detection
feature that detects if the
chassis cove has been
removed. is feature
requires a chassis with
chassis intrusion detection
design.

TPM Header
(17-pin TPMS1)
(see p.1, No. 17)

is connector supports Trusted

GN D

LAD 0

LAD 3

+3 V

+3V S B

D

GN

SER IRQ #

S_P WRDW N #

PC IRST #

GN D

LAD 1

LAD 2

SMB _DAT A_M AIN

Platform Module (TPM) system,

PC ICL K

FRA M E

1

which can securely store keys,
digital certicates, passwords, and

GN D

data. A TPM system also helps
enhance network security, protects
digital identities, and ensures

SMB _CLK _MA IN

platform integrity.

English

21

Print Port Header
(25-pin LPT1)
(see p.1, No. 19)

1

AFD #

STB #

ERR OR#

PIN IT#

SPD 1

SPD 0

SLI N#

SPD 2

SPD 3

SPD 4

SPD 5

SPD 6

GND

SPD 7

ACK #

BUS Y

is is an interface for
print port cable that allows
convenient connection of
printer devices.

PE

SLC T

English

22

B250M-HDV

2.6 M.2_SSD (NGFF) Module Installation Guide

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. e Ultra M.2 Socket
supports type 2230/2242/2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express
module up to Gen3 x4 (32 Gb/s).
* Please be noted that if M2_1 is occupied by a SATA-type M.2 device, SATA3_5 will be
disabled.

Installing the M.2_SSD (NGFF) Module

Step 1

Prepare a M.2_SSD (NGFF) module
and the screw.

Step 2

Depending on the PCB type and length

A

BCD

of your M.2_SSD (NGFF) module,
nd the corresponding nut location to
be used.

No. 1 2 3 4

Nut Location A B C D

PCB Length 3cm 4.2cm 6cm 8cm

Module Type Type2230 Type 2242 Type2260 Type 2280

English

23

4

3

Step 3

Move the stando based on the
module type and length.
e stando is placed at the nut

2

1

location D by default. Skip Step 3 and
4 and go straight to Step 5 if you are
going to use the default nut.
Otherwise, release the stando by
hand.

Step 4

Peel o the yellow protective lm on

A

BCD

the nut to be used. Hand tighten the
stando into the desired nut location
on the motherboard.

English

24

ABCDE

Align and gently insert the M.2 (NGFF)
SSD module into the M.2 slot. Please
be aware that the M.2 (NGFF) SSD
module only ts in one orientation.

Step 5

BC

A

Step 6

Tighten the screw with a screwdriver
to secure the module into place. Please

NUT1NUT2D

do not overtighten the screw as this
might damage the module.

M.2_SSD (NGFF) Module Support List

Vendor Size Interface Length P/N

ADATA 128GB SATA3 2280 AXNS381E-128GM-B
ADATA 256GB SATA3 2280 AXNS381E-256GM-B
ADATA 32GB SATA3 2230 AXNS330E-32GM-B
Crucial 120GB SATA3 2280 CT120M500SSD4
Crucial 240GB SATA3 2280 CT240M500SSD4
Intel 80GB SATA3 2280 Intel SSDSCKGW080A401/80G
Intel 256GB PCIe3 x4 2280 SSDPEKKF256G7
Intel 512GB PCIe3 x4 2280 SSDPEKKF512G7
Kingston 120GB SATA3 2280 SM2280S3
Kingston 480GB PCIe2 x4 2280 SH2280S3/480G
OCZ 512GB PCIe3 x4 2280 RVD400 -M2280-512G (NVME)
Plextor 128GB PCIe3 x4 2280 PX-128M8PeG
Plextor 1TB PCIe3 x4 2280 PX-1TM8PeG
Plextor 256GB PCIe3 x4 2280 PX-256M8PeG
Plextor 256GB PCIe 2280 PX-G256M6e
Plextor 512GB PCIe3 x4 2280 PX-512M8PeG
Plextor 512GB PCIe 2280 PX-G512M6e
Samsung 256GB PCIe3 x4 2280 SM951 (MZHPV256HDGL)
Samsung 256GB PCIe3 x4 2280 SM951 (NVME)
Samsung 512GB PCIe3 x4 2280 SM951 (MZHPV512HDGL)
Samsung 512GB PCIe3 x4 2280 SM951 (NVME)
Samsung 512GB PCIe x4 2280 XP941-512G (MZHPU512HCGL)
SanDisk 128GB PCIe 2260 SD6PP4M-128G
SanDisk 256GB PCIe 2260 SD6PP4M-256G
Team 128GB SATA3 2242 TM4PS4128GMC105
Team 128GB SATA3 2280 TM8PS4128GMC105
Team 256GB SATA3 2280 TM8PS4256GMC105
Team 256GB SATA3 2242 TM4PS4256GMC105
Transcend 256GB SATA3 2242 TS256GMTS400
Transcend 512GB SATA3 2260 TS512GMTS600
Transcend 512GB SATA3 2280 TS512GMTS800
V-Color 120GB SATA3 2280 VLM100-120G-2280B-RD
V-Color 240GB SATA3 2280 VLM100-240G-2280B-RD
V-Color 240GB SATA3 2280 VSM100-240G-2280

B250M-HDV

For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com

English

25

1 Einleitung

Vielen Dank, dass Sie sich für das B250M-HDV von ASRock entschieden haben – ein
zuverlässiges Motherboard, das konsequent unter der strengen Qualitätskontrolle von
ASRock hergestellt wurde. Es liefert ausgezeichnete Leistung mit robustem Design,
das ASRock Streben nach Qualität und Beständigkeit erfüllt.

Da die technischen Daten des Motherboards sowie die BIOS-Soware aktualisiert
werden können, kann der Inhalt dieser Dokumentation ohne Ankündigung geändert
werden. Falls diese Dokumentation irgendwelchen Änderungen unterliegt, wird die
aktualisierte Version ohne weitere Hinweise auf der ASRock-Webseite zur Verfügung
gestellt. Sollten Sie technische Hilfe in Bezug auf dieses Motherboard benötigen, erhalten
Sie auf unserer Webseite spezischen Informationen über das von Ihnen verwendete
Modell. Auch nden Sie eine aktuelle Liste unterstützter VGA-Karten und Prozessoren
auf der ASRock-Webseite: ASRock-Website http://www.asrock.com.

1.1 Lieferumfang

ASRock B250M-HDV-Motherboard (Micro-ATX-Formfaktor)

•

ASRock B250M-HDV-Schnellinstallationsanleitung

•

ASRock B250M-HDV-Support-CD

•

2 x Serial-ATA- (SATA) Datenkabel (optional)

•

1 x Schraube für M.2-Sockel (optional)

•

1 x E/A-Blendenabschirmung

•

Deutsch

26

1.2 Technische Daten

B250M-HDV

Plattform

Prozessor

Chipsatz

Speicher

Erweiterungs­steckplatz

Micro-ATX-Formfaktor

•

Feststoondensator-Design

•

Unterstützt Intel®-CoreTM-i7/i5/i3/Pentium®/Celeron®-

•

Prozessoren der 7. und 6. Generation (Sockeö 1151)
Digi Power design

•

5-Leistungsphasendesign

•

Unterstützt Intel® Turbo Boost 2.0-Technologie

•

Intel® B250

•

Dualkanal-DDR4-Speichertechnologie

•

2 x DDR4-DIMM-Steckplätze

•

Unterstützt ungepuerten DDR4-2400/2133-Non-ECC-

•

Speicher*
* Intel®-Prozessor der 7. Generation unterstützt DDR4 bis
2400; Intel®-Prozessor der 6. Generation unterstützt DDR4
bis 2133.

Unterstützt ECC-UDIMM-Speichermodule (Betrieb im

•

non-ECC-Modus)

Systemspeicher, max. Kapazität: 32 GB

•

Unterstützt Intel® Extreme Memory Prole (XMP) 2.0

•

15-μ-Goldkontakt in DIMM-Steckplätze

•

1 x PCI-Express 3.0-x16-Steckplatz (PCIE1:x16-Modus)*

•

* Unterstützt NVMe-SSD als Bootplatte

2 x PCI-Express 3.0-x1-Steckplätze (Flexible PCIe)

•

Grakkarte

Integrierte Intel® HD Graphics-Visualisierung und

•

VGA-Ausgänge können nur mit Prozessoren unterstützt

werden, die GPU-integriert sind.

Unterstützt integrierte Intel® HD Graphics-

•

Visualisierung: Intel® Quick Sync Video mit AVC, MVC

(S3D) und MPEG-2 Full HW Encode1, Intel® InTruTM

3D, Intel® Clear Video HD Technology, Intel® InsiderTM,

Intel® HD Graphics

Gen9 LP, DX11.3, DX12

•

HWA encodieren/decodieren: VP8, HEVC 8b, VP9,

•

HEVC 10b (bei Intel®-Prozessor der 7. Generation)

Deutsch

27

HWA encodieren/decodieren: VP8, HEVC 8b; GPU/

•

SW encodieren/decodieren: VP9, HEVC 10b (bei Intel®­Prozessor der 6. Generation)
Max. geteilter Speicher: 1024 MB

•

* Die Größe des maximalen Freigabespeichers kann je nach
Betriebssystem variieren.

Drei Grakkarten-Ausgangsoptionen: D-Sub, DVI-D

•

und HDMI
Unterstützt drei Monitore

•

Unterstützt HDMI mit maximaler Auösung von 4K x

•

2K (4096 x 2160) bei 24 Hz / (3840 x 2160) bei 30 Hz
Unterstützt DVI-D mit maximaler Auösung von 1920 x

•

1200 bei 60 Hz
Unterstützt D-Sub mit maximaler Auösung von 1920 x

•

1200 bei 60 Hz
Unterstützt Auto-Lippensynchronizität, hohe Farbtiefe

•

(12 bpc), xvYCC und HBR (Audio mit hoher Bitrate) mit
HDMI-Port (konformer HDMI-Monitor erforderlich)
Unterstützt HDCP mit DVI-D- und HDMI-Ports

•

Unterstützt Blu-ray- (BD) Wiedergabe (Full HD/1080p)

•

mit DVI-D- und HDMI-Ports

Deutsch

28

Audio

LAN

7.1-Kanal-HD-Audio (Realtek ALC887-Audiocodec)

•

* Zur Konguration von 7.1-Kanal-HD-Audio müssen
Sie ein HD-Frontblenden-Audiomodul nutzen und den
Mehrkanalton über den Audiotreiber aktivieren.

Unterstützt Überspannungsschutz (ASRock Full Spike

•

Protection)
ELNA-Audiokondensatoren

•

Gigabit LAN 10/100/1000 Mb/s

•

Giga PHY Intel® I219V

•

Unterstützt Wake-On-LAN

•

Unterstützt Blitzschutz/Schutz gegen elektrostatische

•

Entladung (ASRock Full Spike Protection)
Unterstützt energieezientes Ethernet 802.3az

•

Unterstützt PXE

•