Asrock AM2CPU BOARD User Manual
AM2CPU Board SpecificationsAM2CPU Board Specifications
AM2CPU Board Specifications
AM2CPU Board SpecificationsAM2CPU Board Specifications
Platform: 7.8-in x 5.65-in (19.8 cm x 14.4 cm)
CPU: 940-Pin AM2 Socket Supporting AMD Athlon
TM
Sempron
Supports AMD’s Cool ‘n’ Quiet
Processors
TM
Technology
TM
64 / 64FX / 64X2 and
FSB: Hyper Transport 1000 MHz
Memory: 4 x DDRII DIMM Slots: DDRII_1, DDRII_2, DDRII_3, and DDRII_4
Support DDRII800 / 667 / 533, Max. Total Memory Size 8GB
Dual Channel Memory Technology Support
NOTE
AM2CPU Board provides four 240-pin DDRII (Double Data Rate) DIMM slots, and supports Dual
Channel Memory Technology. For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDRII DIMM pair in the slots of the same color.
In other words, you have to install identical DDRII DIMM pair in Dual Channel A (DDRII_1 and
DDRII_2; Yellow slots) or identical DDRII DIMM pair in Dual Channel B (DDRII_3 and DDRII_4;
Orange slots), so that Dual Channel Memory Technology can be activated. It also allows you to
install four DDRII DIMMs for dual channel configuration, and please install identical DDRII
DIMMs in all four slots. Please note that only the DRAM configuration according to the Allowed
DRAM Configurations Table below is workable.
Do not make any DRAM configuration
that is not listed on the Allowed DRAM Configurations Table.
Allowed DRAM Configurations
Data Bus DIMM Configuration
64 bit Single Side N/A Empty N/A
(single channel) Double Side N/A Empty N/A
128bit Single Side Single Side Empty Empty
(dual channel) Double Side Double Side Empty Empty
DDRII_1 (Yellow) DDRII_2 (Yellow) DDRII_3 (Orange) DDRII_4 (Orange)
Empty N/A Single Side N/A
Empty N/A Double Side N/A
Single Side N/A Single Side N/A
Single Side N/A Double Side N/A
Double Side N/A Single Side N/A
Double Side N/A Double Side N/A
Empty Empty Single Side Single Side
Empty Empty Double Side Double Side
Single Side Single Side Single Side Single Side
Single Side Single Side Double Side Double Side
Double Side Double Side Single Side Single Side
Double Side Double Side Double Side Double Side
It is not allowed to install DDR DIMMs into DDRII slots; otherwise,
this motherboard and DIMMs may be damaged.
AM2CPU Board LayoutAM2CPU Board Layout
AM2CPU Board Layout
AM2CPU Board LayoutAM2CPU Board Layout
1 2 x 240-pin DDRII DIMM Slots
(DDRII_3-4, Dual Channel B, Orange Slots)
2 2 x 240-pin DDRII DIMM Slots
(DDRII_1-2, Dual Channel A, Yellow Slots)
3 CPU Heatsink Retention Module
4 940-Pin AM2 CPU Socket
5 Golden Finger
6 CPU Fan Connector (CPU_FAN1)
7 ATX 12V Power Connector (ATX12V1)
11
1
11
AM2CPU Board InstallationAM2CPU Board Installation
AM2CPU Board Installation
AM2CPU Board InstallationAM2CPU Board Installation
T o install AM2CPU Board into the Future CPU Port on ASRock motherboards that support future
CPU upgrade function (e.g. K8Upgrade series motherboards), please follow the steps below.
STEP 1: Install the AMD 940-pin AM2 CPU into AM2CPU Board, then install the CPU fan and
heatsink into AM2CPU Board, and connect the CPU fan to the CPU fan connector
(CPU_FAN1).
NOTE: Though AM2CPU Board provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work
successfully even without the fan speed control function. If you use a 4-Pin CPU fan on AM2CPU
Board, the fan speed control function needs to depend on the motherboard support.
Pin1-3 Connected
3-Pin Fan Installation 4-Pin Fan Installation
STEP 2: Install DRAM into AM2CPU Board.
STEP 3: If necessary, remove the CPU heatsink retention module from the ASRock motherboard
that you are going to install AM2CPU Board into.
NOTE: Whether or not to remove the CPU heatsink retention module from the ASRock motherboard depends
on the type of CPU fan installed on AM2CPU Board.
STEP 3-1: Place the ASRock motherboard with its backside up.
STEP 3-2: Use a flathead screwdriver to press down the WHITE fastener of the CPU
heatsink retention module through the hole. Repeat with remaining fa steners.
STEP 3-3: Use a pair of pliers to clutch the BLACK supporting part of the CPU heatsink
retention module, then press it down through the hole. Repeat with remaining
supporting parts.
STEP 3-4: Place the ASRock motherboard with its backside down, then remove the
loosened CPU heatsink retention module from the motherboard.
STEP 4: Adjust the jumper settings on ASRock motherboard to fit with the requirement for AMD
STEP 3-1
STEP 3-2
STEP 3-3
STEP 3-4
940-pin AM2 CPU installation. (See ASRock Motherboard User Manual for details).
STEP 5: Secure ASRock motherboard to the chassis.
STEP 6: Install AM2CPU Board into the Future CPU Port (a yellow slot) on ASRock motherboards
that support future CPU upgrade function by aligning the golden finger of AM2CPU
Board with the Future CPU Port.
NOTE: If you install AM2CPU Board and plan to install the AGP VGA card / PCI Express VGA card to the AGP
slot / PCI Express slot nearby Future CPU Port, please do not choose the VGA card with the heatsink
which is too thick to collide with AM2CPU Board. Otherwise, it may cause permanent damage to both
your AM2CPU Board and VGA card!
STEP 7: Secure AM2CPU Board with the bracket to the chassis.
STEP 8: Ensure to connect the power supply with ATX 12V plug to the ATX 12V Power Connector
(ATX12V1) on AM2CPU Board. Failing to do so will cause power up failure.
Please download the latest BIOS version of your motherboard from
our website and install it to your system; otherwise, your motherboard
may not support AM2CPU Board upgrade function. For the latest
BIOS version, please visit our website for installation:
http://www.asrock.com
22
2
22
Loading...