Warning and safety instructions................ 40
Page
No.
2
Page 3
Introduction
Using the correct sling for each patient is an
essential element of safe patient handling. In some
cases, medical and physical factors mean that a
patient's comfort and safety can only be assured by
the provision of a correctly fitted sling. Carers also
benefit from fitting the correct sling on a patient as
their work is made easier and there is less chance of
back injury.
Arjo has long experience of making slings with
people in mind.
A powered sling lifter offers the most secure
transfer method for many patient-handling
procedures. However, providi ng the opt imum sling
for the patient and the purpose is vital in order to
ensure safety and comfort. A sling that is the wrong
size or a bad fit for its patient creates discomfort
and increases the risk of injury.
This guide has been produced to provide users of
Arjo slings with the help and information they need
to ensure safe and comfortable transfer of patients,
whether it's from a bed, the floor, a chair or the
toilet.
3
Page 4
Clip Slings
MAA2000-xx
MAA4000-xx
Unpadded clip sling
The above has no padding in the leg area and
therefore is easier to apply to residents with
skeletal issues such as contractures and curvatures
of the spine. These slings are commonly used on
people who are in moulded wheelchairs.
MAA4060-xx
Padded sling
Padding adds a level of comfort to the leg area of the
slings. The Padding also helps to prevent the
material roping and creasing under legs.
MAA4031xx
Mesh clip sling
The above is most commonly used for showering or
bathing. The mesh allows the water to pass through
the material therefore retaining less water when the
patient is being towel dried. This is a benefit when
the patient is hoisted back into their wheelchair or
onto a towel in bed. The porous material also allows
the skin to breath and can be left underneath the
patient.
Toilet clip sling
Used for toileting, dressing and undressing
patients. The padded arm supports provide the
comfort and support. Leg supports are padded for
comfort but again are narrower to allow clothing to
be removed. Careful patient assessment is
necessary before this sling is used.
4
Page 5
Clip Slings
MAA4031xx
Extended leg padded clip sling
The leg pieces are extended by 100mm (4 inches) to
allow easier attachment of the leg clips. Used for
patients who have larger thighs and hips.
MAV4826MAV4873
MAV4828/
Amputee clip sling with Velcro flap
Used on double amputee above or below knee. The
design allows easier application to the patient
rather than having to log role them in their chair or
bed. The sling is applied as with a normal sling and
the Velcro fastened to provide more support.
Right leg single amputee clip sling
Used for Left single leg amputee patients above,
below or total hip. The larger leg pieceprovides
more support to the stumps of the affected side.
Left leg single amputee clip sling
Used for Right single leg amputee patients above,
below or total hip. The larger leg piece provides
more support to the stumps of the affected side.
5
Page 6
Clip Slings
MAA2090-xx
Amputee clip sling
Used for Bilateral leg amputee patients with above
knee or total hip. The design requires the patient to
be log rolled onto the sling while on the bed or
rolled from side to side in a chair. The aperture does
not allow toileting.
MAV7121
Amputee clip sling with commode aperture
Used for Bilateral leg amputee patients with above
knee or total hip. The design requires the patient to
be log rolled onto the sling while on the bed or
rolled from side to side in a chair. The aperture
allows toileting of a patient who's lower clothing
has already been removed while on the bed.
6
Page 7
Loop Slings
MAA1211-xx
Unpadded loop sling
This sling has no padding in the leg area and is
easier to apply to patients with skeletal issues such
as contractures and curvatures of the spine. These
slings are commonly used on people who are in
moulded wheelchairs.
MAV1816
Padded loop sling
Padding adds a level of comfort to the leg area of
the slings. The Padding also helps to prevent the
material roping and creasing under legs.
MAV1848
Loop toilet sling
Used for toileting dressing and undressing patients.
The padded arm supports provide the comfort and
support, which is lost when providing good access
to the patient's perineum area. Leg supports are
padded for extra comfort but again are narrower to
allow clothing to be removed.
MAV7123
Loop amputee sling
Used for Bilateral leg amputee patients with above
knee or total hip. The design requires the patient to
be log rolled onto the sling while on the bed or
rolled from side to side in a chair. The aperture does
not allow toileting
7
Page 8
Loop Slings
MAV1857
Right leg single amputee loop sling
Used for Left single leg amputee patients above,
below or total hip. The larger leg piece provides
more support to the buttocks and stump of the
affected side.
MAV1852
Left leg single amputee loop sling
Used for Right single leg amputee patients above,
below or total hip. The larger leg piece provides
more support to the buttocks and stump of the
affected side.
8
Page 9
Residents Gallery
Residents in elderly care and other facilities are
very different, they have different diseases and
problems and different backgrounds yet they all
need to be offered a high quality of care.
Choices in care are made on the basis of
assessments of each resident, choices tailored to
their needs and desires as a "typical" resident does
not exist.
In order to plan care for residents there needs to be
a system of standardisation and classification. This
is the reason Arjo developed the Residents Gallery,
it is a classification of five typical residents based
on their degree of functional mobility . But it is more
than just a classification system; it offers colourful
images of five residents who you would actually
meet in real life health care settings. By envisaging
them it makes it possible to discuss choices in care
and rehabilitation in a realistic way.
We know them as Albert, Barbara, Carl, Doris and
Emma and they represent the five different mobility
levels (A-E).
BARBARA
CHARACTERISTICS
• Uses walking frame or similar
• Can support herself to some
degree
• Dependant on carer who is
present in demanding situations
• Not physically demanding for
carer
• Stimulation of remaining
abilities (e.g. ambulation) is
very important
The resident is partly capable of performing daily
activities by him- or herself. However, the
assistance that is required is in general not
physically demanding for the carer/the nurse. The
assistance may consist of verbal support, feedback
or indications, but light physical assistance is also
possible. This assistance can be given in
combination with smaller aids (walking aids,
support or grips and handles) or adaptations in the
environment of the resident. Barbara's remaining
capacity should be stimulated.
ALBERT
CHARACTERISTICS
• Ambulatory, but may use a cane for support
• Independent, can clean and
dress himself
• Can tire quickly
• Stimulation of abilities is very
important
The resident is able to perform daily
activities by him- or herself without
assistance from another person, It is
possible that the resident needs
special aids or appliances. As a rule
there is no risk of physically overloading the carer.
Albert requires careful monitoring.
CARL
CHARACTERISTICS
• Sits in wheelchair
• Is able to partially bear
weight on at least one leg
• Has some trunk stability
• Dependant on carer in most
situations
• Physically demanding for
carer
• Stimulation of remaining
abilities is very important
The resident is not capable of performing daily
activities by him- or herself, but is able to
contribute to the action or perform part of the action
by him- or herself The assistance would, if given
without special precautions, lead to the risk of
physically overloading the carer/the nurse. The
resulting load for the nurse would be in excess of
safe limits for manual handling or static loads. In
these cases it is necessary to use equipment that will
reduce the exposure of the nurse to safe levels. The
resulting load for the nurse would be in excess of
safe limits for manual handling or static loads.
9
Page 10
Residents Gallery
In these cases it is necessary to use equipment that
will reduce the exposure of the nurse to safe levels.
At the same time these residents are able to actively
contribute to the movement and it is important for
the resident to maintain or improve this capacity as
much as possible. The assistance that is given in
these instances is, for example, transfer using an
active lifter. It is important to stimulate remaining
capacity and slow down deterioration of mobility.
DORIS
CHARACTERISTICS
• Sits in wheelchair
• No capacity to support
herself at all
• Cannot stand unsupported
and is not able to bear
weight, not even partially
• Dependent on carer in
most situations
• Physically demanding for
carer
• Stimulation of remaining
abilities is very important
The resident is not capable of performing daily
activities independently or to contribute to this
actively in any substantial or reliable way. The
assistance in this case will, without special
precautions, result in a risk of physically
overloading the nurse/carer. It is necessary to use
equipment that eliminates this risk of overloading.
The resident can, in this case, not contribute
substantially to this movement. In spite of this,
where- and whenever possible it remains important
to activate these residents. The assistance provided
in this case is for example the transfer with a
passive lifter. An extra point of attention in this case
is the prevention of the risks of immobility, (e.g.
give good skin care). It is important to slow down
deterioration of mobility.
EMMA
CHARACTERISTICS
• Passive resident
• Might be almost co mpletely
bedridden
• Often stiff, contracted joints
• Totally dependent
• Physically demanding for carer
• Stimulation and activation is
not a primary goal
The resident is not capable of performing daily
activities independently or to contribute to these
activities actively. The assistance in this case will,
without special precautions, result in a risk of
physically overloading the nurse/carer. It is
necessary to use equipment that eliminates this risk
of overloading. In Emma's case it is not considered
important any more to stimulate her to contribute to
the movement and become active. Promoting or
stimulating mobility and activating the resident is
not a goal in the care plan anymore. Providing
optimum care and/or prevention of the
complications of immobility, e.g. good skin care,
are given priority. Transfers will in this case be
performed with for example a passive litter. The
aim is to avoid complications caused by long-term
confinement to bed and make her as comfortable as
possible.
10
Page 11
When using a sling always ensure…
The sling is smoothly fitted from the base of the
spine (coccyx) to the top of the head. (See fig 1 &
2) An indication of a badly fitted or wrongly sized
sling may be that the head support is 3 or 4" (76102mm) above (sling may be too larg e) or below
the top of the head (sling may be too small).
Fig. 1
Arjo have now produced a sling-size guide tape to
act as a guide to fitting the correct size sling on a
patient. (See fig 3)
Fig. 3
Instructions for using the sling-sizing
guide are as follows.
• Ensure that the tape is used the correct way
round. (Teal (seaweed green) colour - XXS at
the coccyx)
• Ideally the patient should be in a seated position
• Measure from the coccyx to the top of head. The
colour level with the top of the head indicates
the required size.
• If the size falls between two sizes always use the
smallest size
• Patient width and body proportions, should also
be considered and a professional judgement
made
• This sizing tool is only intended as a guide and
is an approximation. Other factors like the
patients physical disabilities, weight
distribution and general physique all need to be
taken into consideration.
• The tape can be used to make dimensional
records of patient for Tailor Made sling
Requirements. (See fig 4 )
Fig. 2
11
Page 12
When using a sling always ensure…
During the lift, the patient will settle into the sling
as their weight is taken up. Ensure the sling
adequately supports the head and the patient's
buttocks are not slipping through the sling aperture.
(See fig 6) Should this happen stop the lift
immediately and retry with a smaller sling size.
Fig. 4
Centre line stitching has also been introduced down
the back of Arjo slings to make it easier for carers
to see exactly where the patient should be
positioned in the sling. The centre line stitching
should be positioned along the patient's spine to
give the sling a perfectly centred fit.
Ensure the leg supports are placed smoothly under
the patient's thighs so that the attachment clips/
loops are between the patient's legs towards the
middle of the thighs. (See fig 5) Indications of a
badly fitted or wrongly sized sling may be the sling
clips/loops only just appearing between the patients
thigh, (sling may be too small) or the leg supports
of the sling digging into the back of the patient's
knees with the sling clips/loops several inches
above the front of the patients thighs (sling may be
too large).
Fig. 5
12
Page 13
Maxislide
52% of accidents and injuries that are suffered by
nursing staff occur during manoeuvres in and
around the bed.
Nurses have always recognised that the principle of
sliding patients in bed reduces the effort, and have
traditionally used sheets and even plastic bags to
aid this movement.
The Maxislide is a unique, ergonomically designed
device having ultra-low friction properties, which
aid carers in moving or positioning patients whilst,
at the same time, encouraging good posture without
causing undue stress to either the patient or carer.
The Maxislide will also encourage patients to help
themselves wherever possible.
The Maxislide CD-ROM is available which can be
used as a user guide; its step-by-step instructions
take the user through the most commonly used
manoeuvres, showing at each stage how the
Maxislide should be used.
Maxislide CD
13
Page 14
Care for your Slings
• The sling should be inspected before use. It is
essential that the slings, their stitching, their
straps, the trim and attachment clips are
carefully inspected. If the slings, trim or straps
are frayed or cut or the clips show any signs of
damage DO NOT USE. Consult the person
responsible for Patient/Resident car e. The sl ing
should be withdrawn from use immediately and
replaced.
• If the sling label is missing or cannot be read the
sling should also be withdrawn from use.
• When laundering slings, they should not be
classified as linen, but as a medical accessory to
a patient transfer lifter and therefore classified
as a medical device.
• Slings should be cleaned and disinfected only in
strict accordance with the manufacturers
instructions. (Refer to sling instruction sheet
MAX. 81687- INT and MAX01510- INT,
supplied with every sling and covered briefly
below).
•Note: If the slings are contaminated
or soiled then the following is a summary
of the washing and drying procedure.
• DO NOT IRON.
• Slings may be air-dried.
• Before washing remove plastic stiffness fr om the
pockets in the sling and replace before use.
• Wash using normal detergents.
Chemical Decontamination: Sodium hypochlorite
(chlorine) 150-300 ppm (parts per million) or
milligrams per litre, Low temperature tumble dry
40ºC/104ºF (test house conditions).
We recommend that the sling is washed before
being used on the next patient, if suspected of being
contaminated or soiled.
•Note: Note: Always follow washing
guidelines indicated on the sling W ashing
and Using instruction label, prior to
washing your sling. .
14
Page 15
Identification of quick reference symbols
3
2
1
1.Stop and read Hoist Operating Instructions before using this sling
2.Maximum washing temperature °C
3.Do not iron
4.Do not tumble dry
5.Maximum weight to be lifted in kilograms - 190kg. Hoist lifting capacity may vary. Refer to hoist load
rating label
6.Sling only to be used on Arjo Sling Lifters
4
3
4
5
6
6
2
1
5
1.Stop and read operating instructions before using this sling
2.Maximum washing temperature (or 194ºF)
3.Do not Iron
4.Low temperature tumble dry
5.Maximum weight to be lifted in Kilograms (or 440lbs)
6.Date of Manufacture
7.Serial number of sling
8.Sling only to be used on these Arjo sling lifters
9.Space for ward/facility/patient name
8
7
9
15
Page 16
Components of a Sling
Stiffeners
Stiffeners pocket
Head piece
Head section
Body section
Leg section
Attachment clip
Shoulder strap
Leg piece with padding
Leg strap
16
Page 17
Sling Size Guide
Please refer to the sling-sizing guide tape, which
can be used as a guide to which sling to use f
or which patient. See page 11for full instructions.
Sling tape size
Passive lifters sling range. Fig a
The measuring tape has centimetres and Inches on
it and is colour coded to represent to colour of the
sling needed for the patient.
Arjos standard sling range is now available in 8
sizes. Extra sizes have been added to lessen the gap
between each size and provide customers with
greater choice and better fit. (fig a)
Arjo standing and raising aid slings are available in
4 sizes (fig b).
•Note: IF THE PATIENTS WEIGHT
FALLS INTO TWO SIZES OR THERE IS
ANY DOUBT ON CHOOSING THE
RIGHT SIZE SLINGS, ALW A YS GO FOR
A SMALLER SIZE.
All Arjo slings are tested to a maximum weight of
200kg or 440lbs.
This patient sling size guide is only an
approximation, other factors which must be
considered when selecting the appropriate sling
are:
• Patient's distribution of body weight, i.e. hips,
thighs, upper body.
• Patient's height, torso length.
• Patient's physical condition, i.e. amputee.
Active lifters sling range. Fig b
Sling size guide:
SIZECOLOURWEIGHT RANGE
Extra Extra smallTeal0 - 25 Kg0 - 55 lbs
Extra smallBrown25 - 35 Kg55 - 77 lbs
SmallRed35 - 60 Kg77 - 132 lbs
MediumYellow55 - 75 Kg121 - 165 lbs
LargeGreen70 - 120 Kg154 - 264 lbs
Large LargePurple100 - 140 Kg240 - 270 lbs
Extra LargeBlue120 - 160 Kg264 - 352 lbs
Extra Extra LargeTerracotta160 - 190 Kg 352 - 418 lbs
17
Page 18
Lifting from a chair
Using the Dynamic Positioning
System ((DPS) Clip Sling)
Ensure the spreader bar is securely attached to the
lifter before commencing with the lifting
procedure. ('Lock and Load' combi system jib
only).
Place the sling around the patient so that the base of
his/her spine is covered, and the head support area
is behind the head. Place each leg piece under the
thigh so that it emerges on the inside of the thigh.
(See fig. 1). You may wish to use the Maxislide to
help in this situation. For reference, see Maxislide
CD-Rom, Technique 24.
Fig. 1
Ensure the positioning handle on the spreader bar is
facing away from the patient, and that the wide part
of the spreader bar is at, or just below shoulder
level. (See fig. 2).
P1392d, P1002a,b,c
Fig. 3
If necessary, lower the spreader bar using the
P1146a,b
handset control, being careful not to lower it onto
the patient, although if this should happen
inadvertently, there is a built in cut-out device
which will prevent any further downwards
movement. Do not continue to press the handsetlowering button.
•Note: If the handset button is
released during lifting or lowering,
powered motion will stop immediately.
Raise the patient by operating the handset control,
move the lifter away from the chair then carefully
lift the positioning handle until the patient is
reclined in the sling - the head support will now
P1392c
come into use. This is the most comfortable
position for transportation, as it reduces pressure on
the thighs. The angle of recline can be adjusted for
increased comfort, if the patient is restless, using
the positioning handle.
Before transportation, turn the patient to face the
attendant at approximately normal chair height.
This gives confidence and dignity and also
improves the Lifter mobility.
Fig. 2
Ensure that the Lifter is close enough to be able to
attach the shoulder clips of the sling to the spreader
bar. To accomplish this you may have to put the
patient's feet on, or over the chassis.
Once the Lifter is in position, first attach the leg
clips to the spreader bar; this will stop the patient
slipping down. Then attach the shoulder strap
attachment clips to the pegs on the spreader bar.
(See fig. 3)
18
Page 19
Lifting from a bed
Position the patient onto the sling by rolling the
patient towards you then folding the sling in half
and placing it behind the patient's back (see fig. 1).
Position the sling carefully so that when rolled back
the patient will lie centrally on the sling (see fig. 2)
and check that the head support area of the sling
covers the patient's head. If the patient is unable to
be rolled, either because of their size or the fact that
they may be in pain, a Maxislide can be used to
slide the patient onto the sling. Refer to the
Maxislide CD-ROM for details of use.
P1393e
P1133b
Fig. 3
Using the positioning handle, tilt the spreader bar
until the shoulder attachment points can be
connected to the sling shoulder strap attachment
clips. (See fig. 4).
Fig. 1
Fig. 2
•Note: When rolling the patient back
onto the sling, roll the patient slightly in
the opposite direction so that the folded
part of the sling can be brought out.
Alternatively, the patient can be brought into a
sitting posture then position the sling as detailed in
the section "To Lift From A Chair".
Approach the bed with the open side of the spreader
bar towards the patient's head. (See fig. 3).
P1395a, P1002 a,b,c
P1022a
Fig. 4
Press down on the positioning handle until
connection of the sling leg pieces is possible. (See
fig. 5) The leg pieces must be brought under the
thighs to connect up, this may involve supporting
one leg at a time to connect up. You may need to
lower the spreader bar a little more, using the
handset control.
P1395b
Using the adjustable width chassis, it is possible to
make adjustments to chassis leg widths to assist
manoeuvrability around obstructions, for example,
bed legs.
Position the Lifter so that the spreader bar is just
above
Fig. 5
19
Page 20
Raising from the floor
Put the sling around the patient as before, either by
using the rolling, sitting or Maxislide method.
Put the sling around the patient as before, by using
the rolling or sitting up method or use the Maxislide
if the patient cannot be rolled or sat up, see
Maxislide CD-ROM Technique 27. Depending on
circumstances, space and/or position of patient etc.
approach the patient with the open part of the
chassis. Open the chassis legs if necessary, and lift
the patient's legs over the chassis as shown in fig 1.
Fig. 1
The patient's head and shoulders could be raised on
pillows for comfort, if required, but this is not
essential when connecting up the sling to the
spreader bar.
With the open part of the spreader bar pointing
down towards the shoulders, attach the shoulder
strap attachment clips, as shown in fig 2 and inset.
The lifters brakes should be applied once the lifter
is in the correct position. This ensures the lifter does
not move and injure the patient.
the effect of raising the patient's head and shoulders
slightly.
P1394c
P1394a
Fig. 3
When lifting from the floor, some attendants prefer
to connect the leg pieces first. This in particular
applies to the very large patient with large thighs. In
this case, raise the hip and knee into maximum
flexion, and attach the leg straps first, then tilt the
spreader bar towards the shoulders to enable the
shoulder straps to be connected.
When all the straps have been properly connected,
raise the patient from the floor in a semi-recumbent
position. Supporting the head can be comfortable
and reassuring for the patient. Once raised from the
floor, ensure the patient's legs are clear of the
chassis before continuing to lift. (See fig. 4). The
leg sections of the sling will tend to be fairly high
up the thigh, so straighten them out for added
comfort. The patient may be positioned in a chair,
or placed onto a bed. If the patient is prone to
extensor spasm, he/she may be lifted by the Arjo
passive lifter, but special attention should be paid to
supporting the legs during the early part of the lift.
Fig. 2
Once connected, raise the hip and knee into
maximum flexion, and push down on the
positioning handle in order to connect the leg strap
attachment clips as shown in fig 3. This will have
P1394d
P1394b, P1002 a,b,c
Fig. 4
20
Page 21
At the toilet
•Note: It is not advisable to use this
sling with patients who are flaccid as they
may slip through the commode hole.
When toileting a patient, use the toilet sling with
headrest. The toilet sling is fitted in a similar
manner to the standard four point sling, except, the
sling is not taken to the base of the patient's spine,
but fitted with the top of the head support area of
the sling level with the top of the patients head as a
guide to positioning. (See fig 1)
Apply the chassis brakes.
Unbutton and / or remove the patient's garments
lower the patient to a comfortable sitting position
P1130a
“Head Section”
support strap buckles
Fig. 1
The ARJO toilet sling has been specially designed
to help support patients whilst toileting.
To provide the best possible access when toileting
the sling has a wide commode opening and because
of this it is essential that: -
• The correct size sling is chosen, relative to the
weight and height of patient and
• Both of the patient's arms are positioned outside
the sling, over the padded areas but under the
"head section" support straps' (See fig. 28) this
will help prevent the patient from sliding
through the sling.
•Note: It is advisable to release the
"head section" support strap buckles
prior to fitting the sling, once the sling is
around the patient, r econnect the support
strap buckles ensuring the patient's arms
are positioned over the sling.
When used in accordance with these instructions
the toileting sling provides a very effective method
of toileting dependent patients.
Once the patient has been lifted and transported to
the toilet, position the lifter so that the patient is
positioned above the toilet seat.
21
Page 22
Lifting from a chair
Using a 2 point spreader bar (Loop
Sling)
The slings to be used with the 2-point spreader bar
are the ARJO loop slings. They are available in four
sizes (small, medium, large and extra large) all
colour coded. A range of more specialised slings
are available please contact ARJO or their
authorised distributors for details.
The loop sling is available with or without head
support. A bathing mesh sling is also available in all
the four sizes with or without head support.
Method 1 - Easing the patient forward, if necessary,
slide the sling down the patient's back until seam
"C" (see fig. a) reaches the base of the spine. Take
attachment points "B" and loop the tails of the sling
underneath the patient's thighs, ensuring the sling
pieces are not twisted underneath the patient. Hook
the loops onto the "opposite side" outer hooks on
the spreader bar. (See fig. b).
A
C
B
B
A
Fig a
METHOD 2
P1395e, mP1138c/2
Fig. b
Method 3 - As method 1 above, but loop a tail
portion of the sling under each thigh and attach to
the same side hook as the shoulder attachment (left
straps to left hook and right straps to right hook).
This method holds the legs in abduction, and is
useful for toileting (see fig. d).
P1395e, mP1138e/2
• Once the sling has been positioned and attached
securely to the spreader bar then lifting can be
carried out using the control handset. For
general patient manoeuvring and transporta tion
see also section "using 4 point spreader bar".
• Apart from the methods listed above, the 2 point
spreader bar with loop slings is also extremely
useful for lifting patients who have contracted
legs, where the patient leg position pr ohibits the
use of the 4 point spreader bar. Attach the sling
in the normal manner as described in "lifting
from the bed".
Method 2 - As method 1 above, but pass each tail
portion of the sling under both thighs, and then out
the other side before attaching points "B" to the
outer hooks on the spreader bar (see fig. c).
METHOD 3
P1395e, mP1138b/2
Fig. c
22
Page 23
Lifting from a bed
Using a 2 point spreader bar (Loop
Sling)
Place the sling under the patient as if it were a draw
sheet (log-roll). Flex the patient's legs, and bring
the sling leg pieces under the thighs, attach the sling
to the spreader bar using any of the methods 1-3 in
'Lifting from a chair'. Alternatively the Maxislide
method can be used in this instance for sliding the
sling underneath the patient, if he/she cannot be log
rolled.
Using the soft stretcher
Warning:
with the Hoist, ensure the Arjo stretcher
support frame has been correctly fitted to the
carrier. Once fitted correctly, the stretcher
frame should be able to rotate approximately
90° about its axis. Do not fit the stretcher
frame in line with the jib.
The soft stretcher is intended for use with the
stretcher frame and is available in two sizes, large
and extra large. It is also supplied in either plain
polyester or polyester mesh for washing use; both
types are available with or without commode hole.
To lift a patient using the stretcher frame and soft
stretcher proceed as follows:
Identify the head of the soft stretcher; a label sewn
to the head end will confirm this.
Before the stretcher can be used
Lifter until the frame is directly over the patient, the
frame is symmetrical and can be used either way
round. (See fig. 2). Lower the stretcher frame
carefully over, and just clear of the patient, aligning
the center of the frame approximately over the
patient's navel. Connect all the sling loops securely
(See fig. 3). Note: The attachment straps have
several connection loops, choose whichever loop is
considered the best to enable the patient to lie in the
most comfort
able position. (See fig. 4).
P1393b
Fig. 2
P1396d
Fig. 1
Position the soft stretcher sling as shown in figure 1
by rolling the patient as if inserting a draw sheet.
Ensure the top section of the sling (indicated by the
label attached to the sling) is under the patient's
head, with the top edge of the sling level with the
top of the head. With the stretcher frame as high up
as possible (but not to come into contact with the
patient, should it swing accidentally), move the
P1393a
Fig. 3
Warning: It is essential to keep the
patient at approximately normal bed
height to ensure stability of the unit and
without losing patient/attendant contact.
When lowering the jib ensure that the patient's or
attendant's legs and feet are well clear of the
moving mast.
Warning: Only use soft stretchers that
have every attachment strap coloured blue.
23
Page 24
Lifting from a bed
•Note: The "head end" straps have a
black tab stitched to them to enable
correct usage with other Arjo stretcher
frames.Do not use any other type of soft
stretcher sling with the Arjo Hoist
The stretcher frame is classified by Arjo as a wet
environment unit, and has a blue and white circular
label to qualify this, attached, (See "Labels"
section). This label signifies that the unit may be
immersed in bath water or used for showering.
24
Page 25
Lifting from the floor
• Some attendants prefer to use a larger sling for
this operation as a larger sling leaves more
room between the patient and the spreader bar,
making the patient feel more comfortable
• · Apply the brakes on the lifter so the patient is
safe from the moving wheels. Raise and support
the patient into a sitting, or half-sitting position.
Feed the sling down the patient's back; bring the
leg pieces of the sling into position. Raise the
patient's legs over the chassis, and bring the
lifter into position as shown in picture opposite.
With the jib as low as possible, attach the
shoulder loops. Bend up the patient's knees to
connect up the leg pieces.
• When lifting or lowering a patient who is
supported by a sling it is not necessary to use
the brakes, this allows the Lifter to move to the
correct position relative to the centre of gravity
of the patient.
• When the patient has been returned to the bed
he/she may be reclined before the sling is
detached.
Fig. 1
P1394e
25
Page 26
Patient Specific Slings (Flites)
Arjo Flites are Patient specific disposable slings.
They can be used in exactly the same way as
standard Arjo slings but they cannot be washed.
As Arjo Flites are patient specific they reduce the
risk of cross infection and can easily be disposed of
if soiled, damaged or suspected of being
contaminated.
• Before using your
Arjo Flites,
familiarise yourself
with the method of
sling operation
detailed in this
document and your
lifter operating and
product care
instructions.
• Arjo Flites must be used in accordance with this
information sheet and in conjunction with the
operating and product care instructions issued
for your lifter. Flites are designed to be
disposable and not laundered so disregard the
instructions for laundering slings.
• Arjo Flites have been designed to support
hospital or care facility patients while using a
patient transfer lifter, under the supervision of
trained nursing staff. All other uses must be
avoided.
• All Arjo Flites sizes will support 190kg (420lbs)
and are coded for size by the colour of the edge
binding tapes, but before using always refer to
the maximum weight limit of the lifter or
attachment being used.
• Each Arjo Flite sling is intended to be specific
to the patient, ensuring that it is always the
correct size, comfortable and having respect for
personal hygiene.
• Arjo Flites can be supplied with two styles of
attachment, the Arjo four point system (four
plastic clips) or with loop attachment straps.
• When the correct size has been determined for a
particular patient, using a permanent marker,
write the patient's name or reference and the
date of issue in the space provided on the label
sewn to the side of the sling. The Flite can be
retained to be re-used with the patient as
required until either the Flite has been soiled,
damaged or is suspected of being contaminated
or if the patient no longer requires it.
• If using Flites with attachment clips, ensure the
"pull straps" at the end of each attachment clip
are only used to attach/detach the clips fr om the
spreader bar, they must not be used for any
other purpose. Do not use the "pull straps" as
an aid to position the patient whilst in the sling.
Improper use of the "pull straps" could result in
damage to the sling or injury to the operator or
patient. Always ensure that the straps
connecting the sling to the attachment clips are
not twisted when the attachment clips are
connected to the spreader bar.
• For patient comfort and label visibility, Arjo
Flites should be used with the DO NOT WASH
label (see Fig. 2) and the attachment straps to
the outer side, and not against the patient.
• Arjo Flites with head support have two pockets
situated at the head section, which should
contain plastic re-inforcement pieces during
use. Always ensure these re-inforcement pieces
have been inserted into the pockets before using
the Flite. Before disposing of the Flite remove
the re-inforcement pieces and retain them for reuse. Decontaminate the re-inforcement pieces
before re-using with Isopropyl alcohol wipes
(see "Care" section in main lifter operating and
product care instructions
• Flites are designed to be used for a limited
period only and by their nature of design must
be treated as a disposable product.
• If the Arjo Flite is
inadvertently washed
or immersed in water,
this label disintegrates
to display the DO
NOT USE symbol (see
Fig. 3). The Flite
should then not be
used under any
circumstances.
• · It is essential that the Arjo Flites, their straps
and attachment clips are carefully inspected
before each and every use. If the Flite fabric or
straps are frayed, or the clips damaged or the
DO NOT USE symbol is visible, the Flite should
be discarded immediately and disposed of in
accordance with hospital or care facility policy.
26
Page 27
Bariatric slings
Bariatric comes from the Greek word 'Baros'
meaning heavy. It is a term given to people who are
generally over the 25 stone or 160kgs. Arjo have
developed a range of slings especially for Bariatric
patients which all have a safe working load of
409kgs or 900lbs. The range comprises of four
BARIATRIC LOOP PADDED SLING SWL
409KG/900LBS
Order refSize
MAV1836Medium
MAV1837Large
MAV1839X Large
MAV1840Extra Extra Large
BARIATRIC LOOP BASIC PADDED SLING SWL
409KG/900LBS
Order refSize
MAV1990 Medium
MAV1991Large
MAV1992Extra Large
MAV1993Extra Extra Large
slings and are available in four sizes they are a
range separate to the standard sling range available
from Arjo. There are two that are standard shaped
Arjo slings and two hammock style slings.
BARIATRIC LOOP DIVIDED LEG HAMMOCK
SLING SWL 409KG/900LBS
Order refSize
MAV1895 Medium
MAV1896Large
MAV1897X Large
MAV1898Extra Extra Large
BARIATRIC LOOP BASIC HAMMOCK SLING SWL
409KG/900LBS
Order refSize
MAV1890 Medium
MAV1891Large
MAV1892Extra Large
MAV1893Extra Extra Large
27
Page 28
Standing and Raising slings- with clip fixing
Position the sling around the patient's back so that
it lies 50mm (2") or so, horizontally above the
patients' waistline, with the patients' arms outside
the sling. Ensure the support strap is separated,
brought loosely around the body , and is not twisted
or trapped behind the patients' back.
Fasten the support strap securely; the strap should
be tight, but comfortable for the patient. (See fig.
1). The support strap will assist in supporting the
patient in the sling during the lifting procedure.
P.1043b
Fig. 1
of the sling attachment clips. (See fig. 3).
P.103 9e, 104 2a
Fig. 3
Next, select an appropriate clip on the opposite end
of the sling, and connect up.
Bring the Lifter carefully up to the patient, placing
the patient's feet on the footrest, and continue
forward until the kneepad is just in contact with the
patient's knees and upper shin. Put on the brakes.
(See fig.2).
P.1039d
Fig. 2
Lower the support arms carefully, using the handset
control, until the sling attachment lugs on the
support arms are close enough to connect up to one
•Note: The patient should be
supported but not pulled forward too
much.
Ensure the sling clips are pulled well down onto the
attachment lugs and secure, before attempting to
lift the patient.
If possible, the patient should now hold onto the
grab handles with one or both hands. (See fig. 4).
P.1039g
Fig. 4
28
Page 29
Standing and Raising slings- with clip fixing
Warning: Always check that all the
sling attachment clips are in position
before and during the commencement of
the lifting cycle and in tension, as the
patient's weight is gradually taken up
If the patient can stand sufficiently well to lock his
/ her knees in the normal way , their knees will come
away from the reaction pad, and he/she can just lean
back into the sling. (See fig. 6)
P.1040b
Fig. 5
P.1040b
•Note: Patients wearing nylon
nightdresses / dressing gowns are prone
to be "slippery" - the sling may ride up
the back causing slight pressure under the
arms. It may be necessary to hold the
sling in position when lifting or lowering.
Release the brakes, and transfer the patient to new
position, i.e. toilet, wheelchair, chair, bed, etc.
•Note: Transportation is possible
with the chassis legs open or closed, but
it will be easier through doorways etc.
with the chassis legs closed.
While the patient is raised, make any necessary
adjustments to clothing, incontinence pads etc.
before lowering again. Lower the patient carefully
using the handset control.
Apply the chassis brakes if leaving the patient at the
toilet, or if leaving the patient unattended.
When the patient is in the new position and seated,
and you wish to remove the sling, un clip the
shoulder support attachment clips, then release the
support strap.
Do not attempt to release the support strap while the
sling supports the patient.
Remove the sling from the patient.
Fig. 6
If the patient is "slumped", he / she can still lean
back into the sling, and be kept in the raised
position by the knees being in contact with the
kneepad.
Patients who have suffered a "stroke" who can only
hold with one hand, or patients who cannot hold on
at all, may still be lifted in this way, but it will be
necessary for the attendant, (or a second attendant),
to hold the patient's arm / arms down in front of the
body during the lift.
•Note: lf the patient lacks sitting
balance and has been returned to the bed
on the Lifter, a second attendant may be
needed to support the patient while the
sling is being removed. (See fig. 7)
P.1042g
Fig. 7
29
Page 30
Standing and Raising Slings- with loop and lock
Allow the patient to hold the handgrips, with their
arms resting on the Arc-Rest. This will not apply if
fitting the sling around the patient before the lifter
is brought into close proximity.
Encourage the patient to lean slightly forwards to
enable the sling to be placed around the lower back
of the patient (see Fig. 1). Position the sling around
the patient's back so that the bottom of the sling lies
horizontally approximately two inches above the
patient's waistline, with the patient's arms outside
the sling. Ensure the support strap is separated,
brought loosely around the body , and is not twisted
or trapped behind the patient's back.
P.1333B
If the Lifter is not already in close proximity to the
patient bring it to the patient as described
previously.
Take each adjustment cord in turn and attach to the
sling. (See Fig. 3).
When both cords are attached correctly make
adjustments on both cords equally so that any slack
is taken up in each cord and the back section of the
sling supports the patient comfortably and securely ,
lock the adjustment cords down into the cord
retaining cleats. (See Fig. 4).
P.1333F, P133E, P1333D
Fig. 1
3. Fasten the support strap securely by overlapping
and pressing the "V elcro" together . The strap should
be tight, but comfortable for the patient. (See Fig.
2).
•Note: The support strap will assist
in supporting the patient in the sling
during the lifting procedure. The strap
also retains the sling in the correct
position around the patient.
Fig. 2
P.1333C
Fitting the loop lock cord attachment system.
Fig. 3
Warning: Ensure the cone is pulled
tightly into the cup section. (See Fig. 3)
Warning: Ensure the cord end knobs are
away from the pro-active pad TM when
the patient's legs are near or in contact
with the pad.
30
Page 31
Standing and Raising Slings- with loop and lock
Detail view showing cords & cleats
Fig. 4
•Note: The patient should be
supported by the sling, but not pulled
forward too much. (See Fig. 4)
If possible, the patient should then hold on to the
Patient Support anus with one or both hands.
The patient is then ready to be lifted.
•Note: If the handset button or dual
control button is released during lifting or
lowering powered motion will stop
immediately.
If the patient is able to offer some assistance when
standing this may be beneficial to patient
confidence and muscular exercise. Encourage the
patient to assist all he/she can to rise from the chair
and/or steady themselves.
Operate the lift button on the handset or dual
control panel to raise the patient to a suitable and
comfortable height for the particular function, e.g.
P1331b/2, P1381b
transportation, toileting with commode, etc. (See
Fig. 6)
P1334f/2
Fig. 6
Warning: Always check that the sling
adjustment cords are fully in position and
locked before and during the
commencement of the lifting cycle, an d in
tension as the patient's weight is gradually
taken up.
•Note: If the patient can stand
sufficiently well and lock his/her knees in
the normal way when fully raised, their
knees will come away from the Proactive
Pad TM and he/she will be able to lean
back into the sling.
Patients who can only hold on with one hand (those
who have suffered a "stroke", for example) may
P1334e/2
still be lifted using an active lifter. The patient may
just rest the unusable arm on the Arc-Rest or hold it
across their chest, and rest their elbow on the end of
the Arc-Rest, while their useable hand holds the
handgrip in the normal way.
Release the brakes, and transfer the patient to new
position, i.e., toilet, wheelchair, chair, bed, etc.
Fig. 5
•Note: Transportation should be
done with the chassis legs closed, it is
easier through doorways etc.
While the patient is raised, make any necessary
adjustments to clothing, incontinence pads etc.,
before lowering again. Lower the patient carefully
31
Page 32
Standing and Raising Slings- with loop and lock
using the control handset or dual control panel.
When the patient is seated in the new position, and
you wish to remove the sling. Pull each cord up
from the locking cleats and slacken the cords
sufficiently to release the Loop LockTM fitting,
and then remove the cords from the sling.
Pull apart the "Velcro" fastening to remove the
support strap.
Remove the sling from the patient. Remove the
lower leg straps if they have been applied.
Warning: If the patient lacks sitting
balance and has been returned to sit on the
side of the bed a second attendant may be
needed to support the patient while the
sling is being removed.
32
Page 33
Boss Slings
The Bos Sling has been designed for use in conjunction with the normal Encore standing sling range. Its
purpose is to offer more support by pulling the patients buttocks inwards towards the hoist thrusting the hips
forwards into Extension. "Patients will hence be standing in a more upright position which is more favourable
for rehabilitation."
The sling can also be used on the Encore for walking practice with patients who have been correctly advised
by a physiotherapist and have progressed from using the recommended Encore walking sling in the initial
stages.
Adjustment Clip
Retainer Tape
KKA5370-SKKA5370-MKKA5370-L KKA5370-XL
Attaching the sling
Attach the Bos Sling exactly as you would the
standard Encore sling. Tighten the waist belt so the
sling is held in place by itself and gives you two
free hands to position the support strap.
Support Strap
Kneeling in front of the patient grasp the left and
right ends of the strap which you have positioned
previously and slide the strap under the patient in
small stages. Sliding one side first and then
following with the other is the preferred method.
The support strap will be hanging down at the back
of the patient under the sling. Working from the
side and the front of the patient lean them forward
and position the strap down towards the patient's
coccyx between the buttocks and the chair. You
may need to swap sides if there is no access to the
back of the patient due to the chair being u p against
the wall.
Before Lifting
Before lifting the patient the adjustment clip can be
opened and any slack taken up. Always check the
clip is closed before lifting.
33
Page 34
Boss Slings
Re-adjusting the support strap
If the Bos Sling requires adjusting this is best
carried out while the patient is sitting. The support
strap can be adjusted during the standing position
but extra help is required to hold the patient safely
while the strap adjustment is being carried out.
If the patient should fall, the support strap and
kneepad will offer more support to the patient until
a chair can be placed under them.
The retainer tape holds the support strap in place
but allows it to be adjusted and pulled further under
patients who require more support. It also prevents
the support strap from being positioned too far
under and taking all the patients weight.
Walking Practice
When the patient is in the standing position, loosen
the support strap as shown. This will give the
patient freedom of movement and allow the
Bos Sling to rest below the buttocks, ready to offer
more support if the patient falls.
Refer to the Encore Operating Instructions for a full
explanation of walking practice.
The Bos Sling can also be use d on the Chorus with
its Loop ‘n’ Lock system for standing only.
Removing the Bos Sling.
After lowering the patient undo the loop and lock as
you would with the standard sling. Slacken off the
support strap, slide the strap in stages away from
the patient and remove.
Product Care
Refer to Slings document MAX01520.INT.
34
Page 35
Walking Jacket
The Arjo walking Jacket was created to enable
therapists and carers to effortlessly aid patients with
standing, stepping and walking practice. The Arjo
walking jacket was designed to work in conjunction
with the Bianca/Bravo lifting system and the
mobile Arjo Maximove/Opera.
Initially, select a Walking Jacket from the range of
sizes to correspond with the weight, height and
proportions of the patient. The jacket should fit
firmly but comfortably around the patient. If it is
obvious that an incorrect size jacket has been first
selected, do not continue, but change it for the
correct size.
variable position loops all colored differently so it
is easy to identify the same loop on either side. The
same colored loop must always be used on both
sides. The loop to be selected will depend on two
factors, the type of Arjo lift being used for the
support and the height of the patient.
The next sequence of operations depends on which
type of Arjo lift is being used for the supportive
function.
Pass the waist straps around the patient ensure they
are not twisted and push them through the loops
(see Fig. 1) tighten the straps so as to be supportive
but not over tight, press the "Velcro" patches
together to fasten.
p1254d
Fig. 2
Identify the front of the jacket (front has two loops
positioned at waist level). Place the jacket over the
head of the patient; ensure the rear section is well
down the patient's back.
Bring the leg sections of the jacket through under
the patient's legs (see Fig. 1) ensuring the sections
are not twisted. Do not connect the leg sections yet.
Fig. 1
Ensure all straps are not twisted before connecting
the buckles. The jacket attachment straps have
Fasten each chest strap (colored black) by
connecting the black buckles and adjust by pulling
the loose end of the strap until tight but not
restrictive. (See Fig. 2).
Take the leg straps (colored white) and connect the
buckles (left strap to left buckle, right strap to right
buckle.) Do not cross the body with the leg straps.
p1254b
Adjust the straps by pulling the loose end of the
strap, again tight but not restrictive. (See Fig. 3).
p1254e
Fig. 3
35
Page 36
Tailor Made Slings
Sometimes a patient's safety and comfort can only
be assured by the provision of a customised sling.
Although Arjo's sling range covers most patient's
needs, there are individual factors- height, body
weight distribution; physical condition- that may
mean a customised sling is the right solution.
Arjo have developed Tailor made slings as a
solution to this problem and we now have long
experience of making slings with specific patients
in mind.
As well as patient specific adaptations, there are
also options to add belts, straps or pull handles to
make positioning and handling of specific patients
easier.
For more information on Arjo Tailor made sling
options, please refer to the 'T ailor made Slings from
Arjo' document, available from Global Marketing.
36
Page 37
Clip Slings
STANDARD SLING
Order re fSize
MAA2000-XSExtra Small
MAA2000-SSmall
MAA2000-MMedium
MAA2000-LLarge
MAA2000-LLLarge Large
MAA2000-XLExtra Large
MAV2908Extra Extra Large
MESH SLING
Order refSize
MAA4060-XSExtra Small
MAA4060-SSmall
MAA4060-MMedium
MAA4060-LLarge
MAA4060-LLLarge Large
MAA4060-XLExtra Large
MAV2994Extra Extra Large
EXTENDED LEG SLING + 100MM
Order refSize
MAV4841Small
MAA4100-MMedium
MAA4100-LLarge
MAA4100-XLExtra Large
MAA4100-XXL Extra Extra Large
EXTENDED LEG UNPADDED SLING + 100MM
Order refSize
MAA2100-MMedium
MAA2100-LLarge
MAA2100-XLExtra Large
RIGHT LEG SINGLE AMPUTEE SLING
Order refSize
MAV4826Medium
MAV4662Large
MAV5767Large Large
MAV4820Extra Large
DOUBLE AMPUTEE SLING
Order refSize
MAA2090-XSExtra Small
MAA2090-SSmall
MAA2090-MMedium
MAA2090-LLarge
MAA2090-XLExtra Large
DOUBLE AMPUTEE MESH SLING
Order refSize
MAV2596Small
MAV2597Medium
MAV2598Large
MAV2599Extra Large
PADDED SLING
Order refSize
MAA4000-XSExtra Small
MAA4000-SSmall
MAA4000-MMedium
MAA4000-LLarge
MAA4000-LLLarge Large
MAA4000-XLExtra Large
MAV4834Extra Extra Large
TOILET SLING WITH HEAD SUPPORT
Order re fSize
MAA4031-XSExtra Small
MAA4031-SSmall
MAA4031-MMedium
MAA4031-LLarge
MAA4031-LLLarge Large
MAA4031-XLExtra Large
AMPUTEE SLING WITH VELCRO FLAP
rder refSize
MAV4828Extra Small
MAV4830Small
MAV4818Medium
MAV4673Large
MAV5766Large Large
MAV5050Extra Large
EXTENDED LEG MESH SLING + 100MM
Order re fSize
MAA4160-MSmall
MAA4160-LMedium
MAA4160-XLExtra Large
LEFT LEG SINGLE AMPUTEE SLING
Order re fSize
MAV4873Medium
MAV4509Large
MAV5768Large Large
MAV4867Extra Large
DOUBLE AMPUTEE SLING WITH COMMODE APERTURE
Order re fSize
MAV7121Small
MAV2630Medium
MAV2632Large
MAV2633Extra Large
MAV7122Extra Extra Large
DOUBLE AMPUTEE MESH WITH COMMODE
SLING
Order re fSize
MAV7136Small
MAV7040Medium
MAV7076Large
MAV7137Extra Large
37
Page 38
Loop Slings
LOOP SLING WITH HEAD SUPPORT
Order refSize
MAA1211-SSmall
MAA1211-MMedium
MAA1211-LLarge
MAA1211-XLExtra Large
LOOP SLING WITHOUT HEAD SUPPORT
rder refSize
MAA1210-SSmall
MAA1210-MMedium
MAA1210-LLarge
MAA1210-XLExtra Large
LOOP TOILET SLING
Order refSize
MAV1848Small
MAV1849Medium
MAV1850Large
MAV1851Extra Large
RIGHT LEG SINGLE LOOP AMPUTEE SLING
Order refSize
MAV1857Small
MAV1858Medium
MAV1859Large
MAV1861Extra Large
RIGHT LEG SINGLE LOOP PADDED AMPUTEE
SLING
Order refSize
MAV1842Small
MAV1843Medium
MAV1844Large
MAV1846Extra Large
PADDED LOOP SLING WITH HEAD SUPPORT
Order refSize
MAV1816Small
MAV1817Medium
MAV1818Large
MAV1819Extra Large
LOOP MESH SLING
Order refSize
MAA1221-SSmall
MAA1221-MMedium
MAA1221-LLarge
MAA1221-XLExtra Large
LOOP AMPUTEE SLING
Order refSize
MAV7123Small
MAV7124Medium
MAV7046Large
MAV7125Extra Large
MAV7126Extra Extra Large
LEFT LEG SINGLE LOOP AMPUTEE SLING
Order refSize
MAV1852Small
MAV1853Medium
MAV1854Large
MAV1866Extra Large
LEFT LEG SINGLE LOOP PADDED AMPUTEE
SLING
Order refSize
MAV1882Small
MAV1883Medium
MAV1884Large
MAV1886Extra Large
38
Page 39
Bariatric Slings
BARIATRIC LOOP PADDED SLING SWL
409KG/900LBS
Order refSize
MAV1836Medium
MAV1837Large
MAV1839X Large
MAV1840Extra Extra Large
BARIATRIC LOOP BASIC PADDED SLING SWL
409KG/900LBS
Order refSize
MAV1990 Medium
MAV1991Large
MAV1992Extra Large
MAV1993Extra Extra Large
BARIATRIC LOOP DIVIDED LEG HAMMOCK
SLING SWL 409KG/900LBS
Order refSize
MAV1895 Medium
MAV1896Large
MAV1897X Large
MAV1898Extra Extra Large
BARIATRIC LOOP BASIC HAMMOCK SLING SWL
409KG/900LBS
Order refSize
MAV1890 Medium
MAV1891Large
MAV1892Extra Large
MAV1893Extra Extra Large
39
Page 40
Warnings and Safety Instructions
• Check all the loops are securely attached before
Warning: IIt is essential to familiarise
yourself with the correct method of use
before any attempt is made to lift a
patient.
Warning: Thoroughly inspect the sling
before any attempt is made to use it. If the
sling is faulty in anyway DO NOT USE.
lifting.
P1502D
Warning: Always carefully assess the
patient for the correct size of sling, as size
coding differs between sling
manufacturers.
• ·Before attaching the sling ensure the spreader
bar is rotated into position so the eventual lift
will resemble fig 1.
Warning: Always check that the sling
attachment loops/clips are fully in
position before and during the
commencement of the lifting cycle, an d in
tension as the patient's weight is gradually
taken up.
•
Warning: Check that all four points of
the sling are securely connected before
lifting.
Fig. 2
• Only when the patient's body weight is fully
supported by the bed, may the sling leg
connection clips be detached, followed by the
shoulder connections.
• Transportation of a patient should always be
done with the chassis legs parallel (closed)
manoeuvrability will be easier, especially
through doorways, with the chassis legs closed.
The patient should be positioned facing the
attendant. Apply the chassis brakes if leaving
the patient unattended.
• The expected operational life for fabric slings
and fabric stretchers is approximately 2 years
from date of manufacture. This life expectancy
only applies if the slings and stretchers have
been cleaned, maintained and inspected in
accordance with the' ARJO Sling Information'
documents, the 'Operating and Product Care
Instructions' and the 'Preventive Maintenance
P1394g
Schedule'.
Flites
• When attaching a loop sling to the 2 point
spreader bar always ensur e the sling attachment
loops are positioned correctly into the retaining
hooks as shown in fig. 2.
• Do not smoke or allow naked flames in the
vicinity of sling.
• ARJO Flites must not be used to support a
patient whilst bathing or showering.
Fig. 1
40
Page 41
Notes
41
Page 42
Notes
42
Page 43
Notes
43
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.