Assembly Instructions - Please keep for future reference
Issue 7 - 20/05/14
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dresser
Dimensions
Width - 99cm
Depth - 40cm
Height - 74.5cm
New Hallingford - Dresser and Stool
258/7796
259/8321
247/8740
274/5136
274/9424
Stool
Dimensions
Width - 51.5cm
Depth - 35.5cm
Height - 45cm
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 29.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
1
Top (D2326A)
(990 x 396mm)
Upright (D2329A)
(333 x 372mm)
Modesty (D2330A)
(598 x 244mm)
Rail (D2331A)
(342 x 66mm) x 2
Back (X350-366)
(350 x 366mm)
Left Side (D2327A)
(721 x 372mm)
2
Right Side (D2328A)
(721 x 372mm)
5
3
Drawer Front (D2309A)
(362 x 162mm) x 2
7
4
6
8
9
10 11
13
12
Stool Top (D2332A)
(513 x 353mm)
Stool Base (D2336A)
(478 x 308mm)
Stool Drawer
Front (D2338A)
(472 x 126mm)
Stool Left Side (D2333A)
(395 x 350mm)
17
14
Stool Right Side (D2334A)
(395 x 350mm)
15
Stool Rail (D2335A)
(478 x 124mm) x 2
18
Stool Drawer
Back (W445-95)
(445 x 95mm)
Stool Drawer Base (T456-297)
(456 x 297mm)
Stool Left
Drawer Side
(W410LH)
(300 x 95mm)
Stool Right
Drawer Side
(W410RH)
(300 x 95mm)
Stool Seat Pad (FHALPAD)
(458 x 300mm)
16
19 20 21
22
23
Dresser
Stool
Drawer Base (T304-367)
(304 x 367mm) x 2
Left Drawer Side (W370-124LH)
(370 x 124mm) x 2
Right Drawer Side
(W370-124RH)
(370 x 124mm) x 2
Drawer Back (W291-124)
(291 x 124mm) x 2
3
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
B C
D E F
G H
Small locking
nut (F3) x 6
L
Nail (F51) x 10
13mm Screw (F52) x 12 13mm Screw (F63) x 12
I
A
Wooden dowel (F22) x 14
19mm Screw (F461) x 4
Metal dowel (F901) x 36
Large locking
nut (F900) x 30
Knock-in Peg (F171GY) x 12
M
R Runner (F160) x 2
b
L Runner (F161) x 2
M
c
L Runner (F159) x 2
M
a
R Runner (F162) x 2
M
d
350mm long
K
9mm Screw (F73) x 4
J
9mm Screw (F74) x 2
N
280mm long
O
Handle (F278) x 2
25mm Screw (F50) x 4
Drawer runner (F1004) x 2
Q
Plastic Nail (F91) x 8
P
Wedgefix (F639) x 6
4
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
Help@ClickSpares.co.uk (quoting your original order number
and the reference numbers below)
x 2
B
B
B
6
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
C
8
9
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
8
9
6
C
8
9
C
6
B
B
C
Groove
C
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
x 2 x 2
x 2
C
C
8
9
8
9
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
11
8 9
6
10
8 9
11
10
10
E
8 9
Attach the handle
Attach a handle to
each drawer front
using 2 screws .
O
G
6
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
P
E
E
E
O
6
G
G
x 2
x 2
x 2
P
P
P
6
x 2
9
8
11
9
11
8
10
E
Assembly Instructions
6
Step 8
Fit runners to the
drawers
Fit runner , marked
with ‘R’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. .
Use a bradawl to mark
the fixing positions, then
secure with 2 screws .
Fit runner , marked
‘L’, to the bottom edge
of the left drawer side
using the same method.
8
M d
9
6
I
M c
D
D
D
A
10mm
A
Prepare the 2 rails
Tap 2 wooden dowels
into each rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into each rail .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
A
Step 9
x 2
5
5
D
5
Plain
chipboard
surface
I
I
Runners must be
pushed up against
the drawer front
M d
R
R
I
I
L
M c
L
6
8
9
x 2
Assembly Instructions
7
Step 10
Step 11
B
D
2
5
5
A
Prepare the right side
a: Fit 2 runners to
the right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Tap a wooden dowel
into the right side .
B
D
2
2
M b
2
H
H
I
M b
M b
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
M b
Finished front edge
I
a:
b:
A
2
H
H
M b
H
H
H
M b
H
D
I
I
D
B
B
Finished
front edge
Finished
front edge
2
2
Join the rails to the
right side
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rails .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
D
5
2
5
D
Finished
front edge
Assembly Instructions
8
Step 12
Finished
front edge
Finished
front edge
a:
Prepare the upright
a: Fit 2 runners to
the upright .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runners .
Screw 2 metal dowels
into the upright .
Insert 2 large locking
nuts into the upright
. .
Turn the upright over
c: Screw 2 metal
dowels into the
upright .
b:
c:
B
D
3
3
M a
3
H
H
M a
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
M a
Finished front edge
I
I
M a
H
M a
H
H
H
M a
H
H
3
3
I
I
D
D
B
B
B
B
3
Turn the upright over
B
3
Finished
front edge
A
Assembly Instructions
9
Step 13
Step 15
Fit the upright
Push the upright onto
the 2 rails .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rails .
Step 14
3
D
5
5
3
5
5
Prepare the modesty
Insert 4 large locking
nuts into the modesty
. .
D
4
D
D
D
D
4
Plain
chipboard
surface
D
D
B
B
Prepare the left side
Tap a wooden dowel
into the left side .
Screw 2 metal dowels
into the left side .
Insert 2 large locking
nuts into the left side
. .
A
1
D
1
B
1
1
Finished
front edge
Assembly Instructions
10
Step 16
Join the modesty to
the left side
Push the modesty
onto the left side .
Note: The top edges
should be flush.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
4
4
1
1
4
1
D
4
Fit the modesty and
left side assembly
Push the modesty
onto the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the modesty .
Using 2 people,
carefully stand the
unit up .
Step 17
4
3
D
4
4
3
Assembly Instructions
11
Step 18
Step 19
Prepare the top
Screw 6 metal dowels
into the top .
B
B
B
B
B
B
B
7
7
plain chipboard surface
Fit the top
Lower the top down
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the left side , right
side and upright .
Using 2 people,
carefully lay the unit
back down onto its
front.
D
7
1
2 3
3
1
2
7
Assembly Instructions
12
Step 20
Step 21
yy
y
x
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up
for the next step.
12
F
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
12
Warning: The
unit is heavy.
Lift with care.
12
b:
F
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
Q
1
2
Q
Q
Q
Q
x
1
2
Assembly Instructions
13
Step 22
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
The assembly of the
dresser is complete.
Follow the next steps
to assemble the stool.
Side
panel
Drawer
Prepare the stool
drawer front
Screw 2 metal dowels
into the stool drawer
front .
B
18
B
B
18
Step 23
Assembly Instructions
14
Step 24
Step 25
Step 26
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Prepare the stool
drawer sides
Insert a small locking
nut into the hole
shown on the stool left
drawer side and stool
right drawer side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
C
19
20
C
C
19
C
20
18
19
B
B
C
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
Attach the stool
drawer sides to the
stool drawer front
Push the stool left
drawer side and stool
right drawer side
onto the back of the
stool drawer front .
Turn the small locking
nuts on the stool left
drawer side and stool
right drawer side .
19
20
18
C
19
20
Groove
18
19
20
Fit the stool drawer
base
Slide the stool drawer
base down the grooves
in the stool drawer sides
. and and down
into the groove in the
stool drawer front .
23
19 20
18
18
19
20
23
Assembly Instructions
15
Step 27
Step 28
Step 29
A
Prepare the stool rails
Tap 2 wooden dowels
into each of the stool
rails .
Insert 4 large locking
nuts into each of the
stool rails .
D
17
A
17
D
D
A
D
D
17
x 2
P
P
P
E
E
Fit the stool drawer
back
Fit the stool drawer back
. down onto the stool
drawer base .
Make sure that the stool
drawer base fits into
the groove in the stool
drawer back .
Hold the stool drawer
back in position and
tap the knock-in pegs
through the holes in the
stool drawer sides
and .
21
23
23
21
21
E
19
20
E
E
19
20
23
21
Fit the wedgefixes
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
P
A
Assembly Instructions
16
Step 30
Prepare the stool left
side
a: Place a runner
onto the stool left side .
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
use the 2nd hole from
the back to fit the 2nd
screw .
c: Screw 6 metal
dowels into the stool
left side .
d: Tap a wooden dowel
. into the stool left side
.
Insert 2 large locking
nuts into the stool left
side .
N
13
K
K
N
K
N
a:
b:
c:
d:
B
B
B
B
B
B
D
D
K
B
13
13
A
D
13
13
13
13
13
K
N
K
A
Assembly Instructions
17
Step 31
Prepare the stool right
side
a: Place a runner
onto the stool right side
. . Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
use the 2nd hole from
the back to fit the 2nd
screw .
c: Screw 6 metal
dowels into the stool
right side .
d: Tap a wooden dowel
. into the stool right
side .
Insert 2 large locking
nuts into the stool
right side .
N
14
K
a:
b:
c:
d:
K
B
14
14
A
D
14
B
B
B
B
B
B
D
D
K
N
K
N
14
14
14
14
K
N
K
Assembly Instructions
18
Step 32
Step 33
Step 34
13
16
Fit the stool base
Push the stool base
onto the stool left side
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool base .
16
13
D
16
13
17
Fit a stool rail to the
stool left side
Push a stool rail onto
the stool left side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool rail .
17
13
D
17
A
Prepare the stool
base
Tap 2 wooden dowels
into the stool base .
Insert 4 large locking
nuts into the stool
base .
D
16
D
D
D
Plain
chipboard
surface
A
A
16
16
D
Assembly Instructions
19
Step 35
Step 36
Step 37
14
16
Secure the stool base
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool base .
Stand the stool up for
the next step.
D
16
17
17
Fit the stool right side
Push the stool right side
. onto the stool base
and the 2 stool rails .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
each of the stool rails .
14 16
17
D
17
14
13
17
Fit the other stool rail
Push the other stool rail
. onto the stool left
side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the stool rail .
17
13
D
17
16
Assembly Instructions
20
Step 38
Step 39
Step 40
14
13
Fit the stool seat pad
Fit the stool seat pad
to the stool top using
4 screws .
Note: Make sure that
you screw into the hard
surface of the stool seat
pad.
22
15
L
L
L
Hard
surface
Soft
surface
22
15
L
L
Prepare the stool top
Screw 4 metal dowels
into the stool top .
B
B
B
B
15
Plain
chipboard
surface
15
B
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the stool sides
and . .
Q
13
14
Q
Q
Q
Q
Assembly Instructions
21
Step 41
Step 42
Fit the stool top
Lower the stool top
down onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the stool left side and
stool right side .
D
15
13
14
15
13
14
J
J
Fit the stool drawer
Slide both the runners
forward and locate the
drawer sides and
between them, lining up
the holes in the drawer
sides with the 2nd
'threaded' holes in the
runners .
Working from the inside
of the drawer, insert 2
screws through the
drawer sides and out into
the 2nd threaded hole in
the runner.
Note: Do not overtighten
the screws .
If they catch on the
runner you may need to
loosen them slightly.
J
N
N
J
2nd threaded
hole
N
J
19 20
19
20
N
Assembly Instructions
22
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers on the component pages)
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 43
Assembly is complete
ALR2981
Loading...