Argos Montana - Corner TV Unit ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 90cm
Depth - 39.5cm
Height - 41cm
Montana - Corner TV Unit
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 08/05/15
Important - Please read these instructions fully before starting assembly
395/6883
391/7657
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 17kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).
• Dispose of all packaging carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Components - Panels
Please check you have all the panels listed below
2
1
3
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF3541)
(353 x 216mm)
Top (DF3539)
(897 x 391mm)
Horizontal (DF3544)
(863 x 355mm)
2
Right End (DF3542)
(353 x 216mm)
Back (DF3543)
(353 x 394mm)
Drawer Front (DF3545)
(889 x 215mm)
Left Drawer Side (W210-124LH)
(210 x 124mm)
Right Drawer Side (W210-124RH)
(210 x 124mm)
Drawer Base (T841-207)
(841 X 207mm)
4
6
8
7
5
Base (DF3540)
(897 x 391mm)
9
10
11
Drawer Back (W830-124)
(830 x 124mm)
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H
M
I
K
Small locking nut (F3) x 2
C
40mm Screw (F910) x 8
L
9mm Screw (F74) x 2
J
9mm Screw (F73) x 4
Knock-in Peg (F171GY) x 4
Large locking nut (F900) x 10
Metal dowel (F901) x 12
Wedgefix (F639) x 4
19mm Screw (F461) x 1
38mm Screw (F81) x 8
Handle (F341) x 1
Drawer runner (F307) x 2
Foot
(F233) x 4
Tools required
Rule Scissors Hammer
Eye protection (when using a hammer or drill)
Cross-head screwdriver
7
Prepare the drawer front
Screw 2 metal dowels into the drawer front .
Note: Tighten the metal dowels up fully against the panels.
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
A
A
C
C
C
C
8
9
Step 2
A
7
Prepare the drawer sides
Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
C
8
9
Attach the drawer sides to the drawer front
Push the left drawer side . and right drawer side . onto the back of the drawer front .
Turn the small locking nuts on the left drawer side and right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
8 9
7
C
C
8 9
9
A
7
A
8
7
Assembly Instructions
5
Step 4
D
D
Fit the drawer base
Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .
Step 5
Fit the drawer back
Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .
Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .
Step 6
11
8 9
7
10
8 9
11
10
10
D
Attach the handle
Attach a handle to the drawer front using screw .
L
G
7
8 9
Step 7
Fit the wedgefixes
Turn the drawer assembly over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
K
D
D
K
K
K
K
K
11
8
10
8
9
11
G
9
L
7
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Prepare the left side
a: Place a runner
onto the left side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the left side .
c: Screw 2 metal
dowels into the left side .
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
J
1
H
J
H
front edge
H
J
back edge
H
J
b:
a:
c:
A
1
1
1
1
B
1
H
A
B
B
A
B
1
H
J
B
B
Assembly Instructions
7
Step 9
Prepare the right side
a: Place a runner
onto the right side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .
b: Slide the runner
back the other way and fit the 2nd screw into the corresponding hole in the right side .
c: Screw 2 metal
dowels into the right side .
Insert 2 large locking nuts into the right side .
Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.
J
2
H
J
H
b:
a:
c:
A
2
2
B
2
Front edge
H
J
Back edge
H
J
H
J
Finished
front edge
Finished
front edge
2
2
Finished
front edge
2
H
A
A
Finished
front edge
Assembly Instructions
8
Step 10
Prepare the top
Screw 6 metal dowels into the top .
A
A
A
A
A
A
A
4
Step 11
Fit the right side to the top
Push the right side onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 12
2
4
B
B
2
4
4
2
Prepare the horizontal
Insert 4 large locking nuts into the horizontal .
B
B
6
B
B
B
6
B
A
Assembly Instructions
9
Step 13
Fit the horizontal
Push the horizontal onto the right side .
Use a screwdriver to tighten the 2 large locking nuts fitted to the horizontal .
2
6
B
6
2
6
1
2
6
B
B
Step 15
Prepare the back
Insert 2 large locking nuts into the back .
Step 14
B
3
3
Fit the left side to the top and horizontal
Push the left side onto the top and horizontal .
Use a screwdriver to tighten the 4 large locking nuts fitted to the top and the horizontal .
1
4
6
B
6
4
4
Assembly Instructions
Step 16
6
3
E
E
Secure the back
Fix the back to the horizontal using 2 screws .
3
6
E
Step 18
Fit the base
Fit the base onto the assembly using 6 screws . .
Step 17
5
E
E
E
E
E
E
E
5
10
Fit the back
Push the back onto the top .
Use a screwdriver to tighten the 2 large locking nuts fitted to the back .
4
3
B
3
4
3
Assembly Instructions
11
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3147
Step 19
Fit the feet
Fit the feet to the base using screws .
Carefully stand the unit up for the next step.
M
5
F
F
M
F
Warning: The unit is heavy. Lift with care.
F
F
M
F
F
M
F
F
M
5
I
2nd threaded
hole
J
I
I
Step 20
Fit the drawer
Slide both the runners forward and locate the drawer sides and between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .
Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner.
Note: Do not overtighten the screws . If they catch on the runner you may need to loosen them slightly.
Assembly is complete
I
J
J
I
8 9
8
9
Loading...