Argos Mix and Match - 3 Door Robe ASSEMBLY INSTRUCTIONS

MADE IN
BRITAIN
Dimensions
Width - 103cm
Depth - 50cm
Height - 167cm
Assembly Instructions - Please keep for future reference
Issue 2 - 09/10/14
Important - Please read these instructions fully before starting assembly
709/2523
709/0848
355/3743
709/2516
Mix and Match - 3 Door Robe
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 58kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.
• Dispose of all packaging carefully and responsibly.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1 2
Hanging Rail (FHR644)
(644mm long)
7
Left Side (D2021A)
(1668 x 494mm)
Right Side (D2022A)
(1668 x 494mm)
Upright (D2023A)
(1555 x 476mm)
Shelf (D2027A)
(332 x 476mm) x 2
Back (X949)
(1580 x 350mm)
Foldy Back (X948)
(1580 x 672mm)
Plinth (D2025A)
(999 x 80mm)
Door (D2026A)
(1567 x 330mm) x 3
Top (D2020A)
(999 x 492mm)
Base (D2024A)
(999 x 478mm)
3
4
5
6
8
9 10 11
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Silver Handle (F1091) x 3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B C
D E F
G H I
Nail (F51) x 40
Blue/Pink Handle (F215) x 3
J K
K
Rail holder
(F1014) x 2
Bracket (F327) x 1
25mm Screw (F50) x 6
13mm Screw (F63) x 20
40mm Screw (F910) x 14
Cranked Hinge (F522) x 6
Hinge plate (F523) x 9
White units are supplied with either Blue or Pink Handles
Beech units are supplied with Silver Handles
13mm Screw (F79) x 10
L
Straight Hinge (F518) x 3
M
Shelf support (F121) x 8
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the upright
Tap 2 wooden dowels into the upright .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Push a rail holder into the upright . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.
B
G
3
J
3
Prepare the top
Tap 2 wooden dowels into the top .
4
Step 1
Step 2
B
G
J
J
J
J
A
A
10mm
A
A
3
Finished
front edge
A
A
3
plain chipboard surface
A
Prepare the base
Tap 2 wooden dowels into the base .
5
Step 3
A
4
5
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
3
Assembly Instructions
5
Join the base and upright
Push the base onto the upright and secure with 2 screws .
D
5
3
Step 4
Step 5
D
D
Fit the top
Push the top onto the upright and secure with 2 screws .
D
4
3
4
D
D
5
plain chipboard surface
3
Finished
front edge
Assembly Instructions
6
Step 6
Prepare the left side
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
B
G
J
J
J
J
B
1
J
1
1
J
J
J
Finished
front edge
Step 7
Prepare the right side
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
J
2
2
J
G
Assembly Instructions
7
Step 8
Step 9
D
D
D
D
Fit the right side
Push the right side onto the top and base and secure with 4 screws .
2
2
4
5
D
4
5
A
Prepare the plinth
Tap 2 wooden dowels into the plinth .
6
A
A
plain chipboard surface
6
Assembly Instructions
8
Step 10
Step 11
Fit the left side
Push the left side onto the assembly and secure with 5 screws .
D
D
D
D
D
1
1
D
D
Fit the plinth
Push the plinth onto the right side and secure with screw .
6
2
D
plain chipboard surface
6
2
Assembly Instructions
9
Step 12
Warning: The unit is heavy. Lift with care.
11
10
F
H
F
Fit the back panels
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
and foldy back , unit colour facing down, onto the unit as shown. Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the upright panel’s edge.
Nail around the outside edges of the 2 backs.
Note: Do not nail where the 2 backs meet. Nails should be spaced about 150mm apart.
c: Using 9 screws ,
screw down between the 2 backs and into the upright panel’s back edge.
Note: You will need to keep 1 screw to use in the final step.
Stand the unit up for the next step.
3
3
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
yyy
x
x
F
c:
11
10
F
x 9
H
b:
10
11
Assembly Instructions
10
Step 13
Step 14
Fit the hanging rail
Push the hanging rail into the rail holders fitted to the right side and upright .
7
7
B
3
2
7
B
L
x 4
L
x 4
8
8
Fit the shelves
For each of the 2 shelves , insert 4 shelf studs at the required height.
Lower the 2 shelves down onto the shelf studs .
8
L
8
L
Assembly Instructions
11
Step 15
Prepare the 2 outer doors
Important: The 6 hinges used in this step are in the bag marked as AHP1546.
Push fit 3 cranked hinges . into 2 of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
G
K
9
x 2
K
G
G
K
G
G
K
G
G
9
9
L
G
G
90
90
L
G
G
L
G
G
x 1
K
L
Step 16
Prepare the centre door
Important: The 3 hinges used in this step are in the bag marked as
AHP1043.
Push fit 3 straight hinges . into 1 of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
G
L
9
AHP1546
AHP1043
AHP1043
AHP1546
Assembly Instructions
12
Step 17
I
a: b:
c: d:
J
K
J
J
B
J
K
K
K
A
K
J
B
e:
I
E
E
9
9
Fit the 2 outer doors and their handles
2 people are needed here
Note: The easiest way to
attach each outer door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate .
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each of the outer doors . using 2 screws .
Note: Do not overtighten screw .
K
K
K
J
J
J
K
J
I
E
E
9
9
Assembly Instructions
13
Step 18
Fit the centre door and its handle
Note: The easiest way to attach the centre door . is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
the centre door using 2 screws .
Note: Do not overtighten screw .
L
L
L
J
J
J
L
J
I
E
E
9
9
a: b:
c: d:
J
L
J
J
B
J
L
L
L
A
L
J
B
e:
I
E
E
9
Assembly Instructions
14
Step 19
b:
c:
d:
a:
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
This shows the hinge and plate that is
fitted to the outer doors.
The ones fitted to the centre door are
adjusted in the same way.
Assembly Instructions
15 ALR2842
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 20
Top of Unit
WALL
WALL
Back of Unit
Fit the bracket
To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted to the top of the unit.
Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back of the unit to the wall.
Fix the bracket loosely onto the top of the unit using screw and mark the wall for the wall fixing.
Swivel the bracket away from the wall and drill a hole in the wall using a suitable drill bit and fit your wall fixing.
Swivel the bracket back and fix the bracket to the wall, then tighten Screw .
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Warning: The unit is heavy. Lift with care.
Assembly is complete
C
C
F
C
C
F
C
F
C
C
4
4
MADE IN
BRITAIN
Dimensions
Width - 103cm
Depth - 50cm
Height - 167cm
Assembly Instructions - Please keep for future reference
Issue 3 - 21/01/15
Important - Please read these instructions fully before starting assembly
709/2523
709/0848
355/3743
709/2516
Mix and Match - 3 Door Robe
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 58kgs. Please lift with care.
• Check you have all the components and tools listed on pages 1, 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
Tools required
Rule
Scissors
Spirit level
Hammer Bradawl
Eye protection (when using a hammer or drill)
Cross-head screwdriver
Step ladder
Electric drill (only use when drilling into walls)
Square
mm
10
20
30
40
50
60
70
80
90
100
mm
10
20
30
40
50
60
70
80
90
100
• We do not
recommend the
use of power
drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
1 2
Hanging Rail (FHR644)
(644mm long)
7
Left Side (D2021A)
(1668 x 494mm)
Right Side (D2022A)
(1668 x 494mm)
Upright (D2023A)
(1555 x 476mm)
Shelf (D2027A)
(332 x 476mm) x 2
Back (X949)
(1580 x 350mm)
Foldy Back (X948)
(1580 x 672mm)
Plinth (D2025A)
(999 x 80mm)
Door (D2026A)
(1567 x 330mm) x 3
Top (D2020A)
(999 x 492mm)
Base (D2024A)
(999 x 478mm)
3
4
5
6
8
9 10 11
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Silver Handle (F1091) x 3
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B C
D E F
IG H
Nail (F51) x 40
Blue/Pink Handle (F215) x 3
J
J
Rail holder
(F1014) x 2
25mm Screw (F50) x 6
13mm Screw (F63) x 20
40mm Screw (F910) x 14
J
White units are supplied with either Blue or Pink Handles
Beech units are supplied with Silver Handles
13mm Screw (F79) x 9
Shelf support (F121) x 8
K L
N
Cranked Hinge (F522) x 6
Hinge plate (F523) x 6
M
Straight Hinge (F518) x 3
Hinge plate (F523) x 3
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
These 6 hinges and plates are in the bag labelled as . . . 1546
These 3 hinges and plates are in the bag labelled as . . . 1043
Important: Keep the Hinges and Hinge Plates in their bags until they are used. DO NOT mix them up.
A
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the upright
Tap 2 wooden dowels into the upright .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Push a rail holder into the upright . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the upright , making sure that the slot is facing towards the finished front edge.
Important: The 3 hinge plates used in this step are in the bag marked as . . . 1043.
B
G
3
M
3
Prepare the top
Tap 2 wooden dowels into the top .
4
Step 1
Step 2
B
G
M
M
M
M
A
A
10mm
A
A
3
Finished
front edge
A
A
3
plain chipboard surface
A
Prepare the base
Tap 2 wooden dowels into the base .
5
Step 3
A
4
5
Finished
front edge
Finished
front edge
. . . 1043
. . . 1546
Finished
front edge
Finished
front edge
Finished
front edge
3
Assembly Instructions
5
Join the base and upright
Push the base onto the upright and secure with 2 screws .
D
5
3
Step 4
Step 5
D
D
Fit the top
Push the top onto the upright and secure with 2 screws .
D
4
3
4
D
D
5
plain chipboard surface
3
Finished
front edge
Assembly Instructions
6
Step 6
Prepare the left side
Push a rail holder into the left side . Make sure that it is fitted straight, in line with the panel edges and then secure with screw .
Fit 3 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.
B
G
K
K
K
K
B
1
K
1
1
K
K
K
Finished
front edge
Step 7
Prepare the right side
Fit 3 hinge plates onto the right side , making sure that the slot is facing towards the finished front edge.
K
2
2
K
G
Important: The 3 hinge plates used in this step are in the bag marked as . . . 1546.
. . . 1043
. . . 1546
Important: The 3 hinge plates used in this step are in the bag marked as . . . 1546.
. . . 1043
. . . 1546
Assembly Instructions
7
Step 8
Step 9
D
D
D
D
Fit the right side
Push the right side onto the top and base and secure with 4 screws .
2
2
4
5
D
4
5
A
Prepare the plinth
Tap 2 wooden dowels into the plinth .
6
A
A
plain chipboard surface
6
Assembly Instructions
8
Step 10
Step 11
Fit the left side
Push the left side onto the assembly and secure with 5 screws .
D
D
D
D
D
1
1
D
D
Fit the plinth
Push the plinth onto the right side and secure with screw .
6
2
D
plain chipboard surface
6
2
Assembly Instructions
9
Step 12
Warning: The unit is heavy. Lift with care.
11
10
F
H
Fit the back panels
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
and foldy back , unit colour facing down, onto the unit as shown. Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the upright panel’s edge.
Nail around the outside edges of the 2 backs.
Note: Do not nail where the 2 backs meet. Nails should be spaced about 150mm apart.
c: Using 9 screws ,
screw down between the 2 backs and into the upright panel’s back edge.
Stand the unit up for the next step.
3
3
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
yyy
x
x
F
c:
11
10
F
H
b:
10
11
Assembly Instructions
10
Step 13
Step 14
Fit the hanging rail
Push the hanging rail into the rail holders fitted to the right side and upright .
7
7
B
3
2
7
B
C
x 4
C
x 4
8
8
Fit the shelves
For each of the 2 shelves , insert 4 shelf studs at the required height.
Lower the 2 shelves down onto the shelf studs .
8
C
8
C
Assembly Instructions
11
Step 15
Prepare the 2 outer doors
Important: The 6 hinges used in this step are in the bag marked as . . . 1546.
Push fit 3 cranked hinges . into 2 of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
G
L
9
x 2
L
G
G
L
G
G
L
G
G
9
9
N
G
G
90
90
N
G
G
N
G
G
x 1
L
N
Step 16
Prepare the centre door
Important: The 3 hinges used in this step are in the bag marked as
. . . 1043.
Push fit 3 straight hinges . into 1 of the doors .
Secure each hinge with 2 screws .
Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.
G
N
9
Important: The 3 hinges used in this step are in the bag marked as . . . 1043.
. . . 1043
. . . 1546
Important: The 6 hinges used in this step are in the bag marked as . . . 1546.
. . . 1043
. . . 1546
Assembly Instructions
12
Step 17
J
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
e:
J
E
E
9
9
Fit the 2 outer doors and their handles
2 people are needed here
Note: The easiest way to
attach each outer door is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate .
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
each of the outer doors . using 2 screws .
Note: Do not overtighten screw .
L
L
L
K
K
K
L
K
J
E
E
9
9
The 2 outer doors have the cranked hinges.
Assembly Instructions
13
Step 18
Fit the centre door and its handle
Note: The easiest way to attach the centre door . is to fit the top hinge first, then align and fit the other hinges.
a: Push the hinge
onto the front part of the hinge plate . The recess at the bottom of screw B goes into the slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge plate as you slide it across as far as it will go. Tighten screw A.
c: The hinge must be
flat against the hinge plate prior to any adjustment.
d: The hinge must
NOT be AT AN ANGLE to the hinge plate when assembled. This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure. Remove the hinge from the hinge plate and then re-assemble being careful to follow instructions a-c.
e: Attach a handle to
the centre door using 2 screws .
Note: Do not overtighten screw .
N
N
N
M
M
M
N
M
J
E
E
9
9
a: b:
c: d:
M
N
M
M
B
M
N
N
N
A
N
M
B
e:
J
E
E
9
Assembly Instructions
14
Step 19
b:
c:
d:
a:
Adjust the doors if needed
a: Before adjusting the
doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.
b: Height adjustment.
Loosen screws A on hinge plates and move door up or down as required. Retighten screw A.
c: Forward and Back
adjustment. Loosen screw B on hinge plate and move door in or out as required. Retighten screw B.
d: Sideways
adjustment. To move door ‘out’ loosen screw C. To move door ‘in’ tighten screw C.
A
A
B
C
This shows the hinge and plate that is
fitted to the outer doors.
The ones fitted to the centre door are
adjusted in the same way.
Assembly Instructions
15 ALR2842
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 20
Fit the overbalance protector kit
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
I
I
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
I
Strap
Washer
Screw
TOP OF UNIT
I
Loading...