Argos Malvern - 5 Drawer Chest ASSEMBLY INSTRUCTIONS

Page 1
MADE IN
BRITAIN
Dimensions
Width - 79.5cm
Depth - 39.5cm
Height - 109cm
Malvern - 5 Drawer Chest
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 11/05/15
Important - Please read these instructions fully before starting assembly
391/9538
395/6326
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Warning: This unit weighs approximately 39kgs. Please lift with care.
• Check you have all the components and tools listed on pages 2 and 3.
• Remove all fittings from the plastic bags and separate them into their groups.
• Keep children and animals away from the work area, small parts could choke if swallowed.
• Parts of the assembly will be easier with 2 people.
• Make sure you have enough space to layout the parts before starting.
• Do not stand or put weight on the product, this could cause damage.
• Assemble the item as close to its final position (in the same room) as possible.
• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).
1
Care and maintenance
• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.
• From time to time check that there are no loose screws on this unit.
• This product should not be discarded with household waste. Take to your local authority waste disposal centre.
Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.
• We do not recommend the use of power drill/drivers for
inserting screws, as this could damage the unit. Only use hand screwdrivers.
Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.
• Dispose of all packaging carefully and responsibly.
Page 3
Components - Panels
Please check you have all the panels listed below
2
1
2
3
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left Side (DF92)
(1026 x 374mm)
Right Side (DF93)
(1026 x 374mm)
Top (DF95)
(795 x 392mm)
Base (DF94)
(787 x 374mm)
Rail (DF99)
(753 x 78mm)
Top Drawer Front (DF4049)
(778 x 195mm) x 4
Bottom Drawer Front (DF105)
(778 x 243mm)
Bottom Left Drawer Side (W370-165LH)
(370 x 165mm)
Drawer Base (T713-367)
(713 x 367mm) x 5
Bottom Right Drawer Side (W370-165RH)
(370 x 165mm)
Bottom Drawer Back (W702-165)
(702 x 165mm)
Top Drawer Back (W702-124)
(702 x 124mm) x 4
Top Left Drawer Side (W370-124LH)
(370 x 124mm) x 4
Top Right Drawer Side (W370-124RH)
(370 x 124mm) x 4
4
5
6
8
9
10
11
12
7
13
14
Back (X1058-779)
(1058 x 779mm)
15
Page 4
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
C
Metal dowel (F901) x 16
Wooden dowel (F22) x 10
Small locking nut (F3) x 10
Large locking nut (F900) x 6
40mm Screw (F910) x 4
P
R Runner (F160) x 5
b
L Runner (F161) x 5
P
c
L Runner (F159) x 5
P
a
R Runner (F162) x 5
P
d
350mm long
J
13mm Screw (F63) x 30
Knock-in Peg (F171GY) x 20
K
Wedgefix (F639) x 20
L
M N
Nail (F51) x 25
38mm Screw (F81) x 8
9mm Screw (F73) x 30
19mm Screw (F461) x 10
Foot
(F233) x 4
Handle (FBARHANDLE) x 5
O
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Page 5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
6
x 4
x 4
x 4
x 4
A
A
B
B
B
B
8
9
8
9
A
A
Step 2
Prepare the 4 top drawer fronts
Screw 2 metal dowels into each of the top drawer fronts .
Note: Tighten the metal dowels up fully against the panels.
A
6
Prepare the top drawer sides
Insert a small locking nut into the hole shown on the top left drawer side and the top right drawer side .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Step 3
B
8
9
Attach the top drawer sides to the top drawer fronts
Push the top left drawer sides . and top right drawer sides . onto the back of the top drawer fronts .
Turn the small locking nuts on the top left drawer side and top right drawer side .
Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.
8
9
6
B
B
8
9
6
Page 6
6
J
J
Assembly Instructions
5
Step 4
x 4
x 4
x 4
x 4
J
J
K
14
8
9
14
10
8
9
Fit the drawer base
Slide the drawer base down the grooves in the top drawer sides and . and down into the groove in the top drawer front .
Step 5
Fit the top drawer back
Fit the top drawer back . between the top drawer sides and . Make sure that the drawer base fits into the groove in the top drawer back .
Hold the top drawer back in position and tap the knock-in pegs through the holes in the top drawer sides and . .
Step 6
14
8
9
6
10
8 9
14
10
10
J
Attach the handles
Attach a handle to each of the top drawer fronts using screws . .
M
G
6
8
9
Step 7
Fit the wedgefixes
Turn the 4 top drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
K
K
K
K
K
G
G
M
6
Page 7
Assembly Instructions
6
Step 8
Step 9
Prepare the bottom drawer front
Screw 2 metal dowels into the bottom drawer front .
A
7
Prepare the bottom drawer sides
Insert a small locking nut into the hole shown on the bottom left drawer side and the bottom right drawer side . .
Step 10
B
11
12
Attach the bottom drawer sides to the bottom drawer front
Push the bottom left drawer side . and bottom right drawer side . onto the back of the bottom drawer front .
Turn the small locking nuts on the bottom left drawer side and bottom right drawer side . .
11
12
7
B
11
12
7
A
B
A
B
B
B
B
11
12
12
11
A
A
7
Page 8
7
Assembly Instructions
7
Step 11
J
J
14
11
12
J
J
14
13
11
12
7
Fit the wedgefixes
Turn the drawer assembly over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.
Fit the drawer base
Slide the drawer base down the grooves in the bottom drawer sides and and down into the groove in the bottom drawer front .
Step 12
Step 13
14
11
12
7
Attach the handle
Attach the handle to the bottom drawer front . using screws .
G
7
M
Fit the bottom drawer back
Fit the bottom drawer back between the bottom drawer sides and . Make sure that the drawer base fits into the groove in the bottom drawer back .
Hold the bottom drawer back in position and tap the knock-in pegs through the holes in the bottom drawer sides and .
13
11
12
14
13
13
J
11
12
Step 14
K
x 4
K
K
K
K
K
G
G
M
Page 9
Assembly Instructions
8
Step 15
Fit runners to the 4 top drawers
Fit runner , marked with ‘R’, to the bottom edge of the top right drawer side , as shown, making sure that it is pushed up against the back of the top drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the top left drawer side using the same method.
8
P d
9
6
H
P c
Step 16
Fit runners to the bottom drawer
Fit a runner , marked with ‘R’, to the bottom edge of the bottom right drawer side . , as shown, making sure that it is pushed up against the back of the bottom drawer front . Use a bradawl to mark the fixing positions, then secure with 2 screws .
Fit runner , marked ‘L’, to the bottom edge of the bottom left drawer side using the same
11
P d
12
7
H
P c
H
H
P d
R
R
L
P c
L
Runners must be
pushed up against
the drawer front
9
8
6
x 4
H
H
H
H
P d
R
R
L
P c
L
Runners must be
pushed up against
the drawer front
H
H
11
12
7
Page 10
D
D
Finished
front edge
Assembly Instructions
9
Step 17
P a
I I
1st screw
2nd screw
I
3rd screw
Finished
front edge
P a
H
Finished
front edge
a:
b:
Prepare the left side
a: Fit 5 runners to
the left side .
The 1st screw uses the 1st hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
c: Tap 4 wooden
dowels into the left side .
Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Insert 2 large locking nuts into the left side . .
Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Screw a metal dowel into the left side .
P a
1
I
I
H
C
1
1
D
1
P a
c:
C
10mm
D
I
P a
I
I
I
P a
I
I
I
P a
I
I
I
P a
I
I
I
P a
I
I
1
Finished
front edge
1
H
H
H
H
H
Finished
front edge
1
D
D
C
C
A
A
Page 11
D
D
Assembly Instructions
10
Step 18
P b
H
P b
II
1st screw
2nd screw
I
3rd screw
Prepare the right side
a: Fit 5 runners to
the right side .
The 1st screw uses the 1st hole in from the front of the runner.
The 2nd and 3rd screws . use the holes that line up with the other panel holes.
b: Fit a screw into
the 2nd hole in at the top of the runner .
c: Tap 4 wooden
dowels into the right side .
Insert 2 large locking nuts into the right side .
Screw a metal dowel into the right side .
P b
2
I
I
H
C
2
D
2
P b
b:
c:
a:
Finished
front edge
Finished
front edge
I
I
P b
I
I
I
P b
I
I
I
P b
I
I
I
P b
I
I
I
P b
I
Finished
front edge
Finished
front edge
H
H
H
H
H
Finished
front edge
D
D
C
C
A
2
2
2
2
A
Page 12
Finished
front edge
Finished
front edge
D
Assembly Instructions
11
Step 19
Step 20
Fit the rail to the right side
Push the rail onto the right side .
Use a screwdriver to tighten the large locking nut fitted to the rail .
Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.
Step 21
Prepare the rail
Tap 2 wooden dowels into the rail .
Insert 2 large locking nuts into the rail .
C
5
D
5
5
Finished
front edge
C
C
D
A
C
5
2
5
C
C
5
5
2
Fit the left side to the rail
Push the left side onto the rail .
Use a screwdriver to tighten the large locking nut fitted to the rail .
1
5
5
C
1
Page 13
Finished
front edge
Finished
front edge
Assembly Instructions
12
Step 22
1
Fit the base
Attach the base to the left side and right side using 4 screws . .
4
1
2
E
E
E
E
E
4
2
Prepare the top
Screw 4 metal dowels into the top .
A
3
A
A
A
A
Finished
front edge
3
Fit the top
Push the top onto the assembly.
Use a screwdriver to tighten the 4 large locking nuts fitted to the left side and right side .
C
1
2
3
Step 23
Step 24
3
1
2
Page 14
yy
yy
xx
xx
Assembly Instructions
13
Step 25
Step 26
Fit the feet
Fit the feet to the base using screws .
F
N
4
F
N
F
F
N
F
F
N
F
F
N
F
4
b:
L
Fit the back
a: Square up the unit by
making sure that measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the outside edges of the back .
Note: Nails should be spaced about 150mm apart.
Stand the unit up for the next step.
15
L
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
15
15
Warning: The unit is heavy. Lift with care.
Page 15
Assembly Instructions
14
Step 27
Side panel
Drawer
Fit the drawers
Slide the wheels of the runners fitted to the drawers, over the wheels of the runners fitted to the side panels and push the drawers into position.
Top drawer
Bottom drawer
Top drawer
Top drawer
Top drawer
Page 16
Assembly Instructions
15
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR3206
Step 28
Fit the overbalance protector kit
To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . to the unit, or an alternative fixing method of your choice.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.
Assembly is complete
O
Attach the
strap to the unit
Attach the
strap to the wall
Wall fixing
(not supplied)
Washer
Strap
Strap
O
O
Example
Screw
(not supplied)
Washer
Screw
UNIT
Loading...