Argos Malibu - Desk ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 120cm

Depth - 49cm

Height - 72cm

Malibu - Desk

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 12 - 22/07/14

Important - Please read these instructions fully before starting assembly

275/6297

278/6009

274/6616

278/5220

247/3848

278/6652

268/6965

238/3615

275/3922

246/4950

246/5818

280/0332

247/7167

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 24kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: If there is any chance of this unit being pulled over by children etc. it is recommended that the unit is secured to a wall using suitable fixings (not supplied).

• Dispose of all packaging carefully and responsibly.

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Drawer Back (W317-124)

(317 x 124mm) x 3

Drawer Base (T328-317)

(328 x 317mm) x 3

Back (X646-375)

(646 x 375mm)

Left Side (D2785A)

(706 x 353mm)

Right Side (D2786A)

(706 x 353mm)

Bookcase End (D2787A)

(706 x 186mm) x 2

Shelf (D2788A)

(394 x 182mm) x 3

Rail (D2790A)

(349 x 80mm)

Plinth (D2789A)

(349 x 92mm)

Drawer Front (D2791A)

(345 x 196mm) x 3

Top (D2784A)

(1200 x 490mm)

Left Drawer Side (W320-124LH)

(320 x 124mm) x 3

Right Drawer Side (W320-124RH)

(320 x 124mm) x 3

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 8

Metal dowel (F901) x 14

Large locking nut (F900) x 8

Small locking nut (F3) x 6

40mm Screw (F910) x 16

NL M

25mm Screw (F50) x 3

Rule Scissors Hammer Eye protection

(when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Handle (F631) x 3

Nail (F51) x 11

Knock-in Peg (F171GY) x 12

Wedgefix (F639) x 6

Drawer runner (F1004) x 6

9mm Screw (F73) x 12

9mm Screw (F74) x 6

Plastic Nail (F91) x 8

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

x 3

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

+ 11 hidden pages