Argos Malibu - Corner Desk ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 89.5cm

Depth - 89.5cm

Height - 72cm

Malibu - Corner Desk

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 2 - 18/03/13

Important - Please read these instructions fully before starting assembly

617/3223

617/3900

617/3230

621/3310

621/3327

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 19kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Top (D0872A)

(895 x 895mm)

2 3

Left Side (D0873A)

(706 x 244mm) x 2

Right Side (D0874A)

(706 x 244mm) x 2

Plinth (D0875A)

(445 x 80mm) x 2

5 Shelf (D0876A)

(445 x 240mm) x 4

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 4

Metal dowel (F901) x 8

D E

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

40mm Screw (F910) x 20

Large locking nut (F900) x 8

Bracket (F327) x 1

13mm Screw (F79) x 1

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill (only use when drilling into walls)

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Prepare the 2 left sides

Insert 2 large locking nuts into each of the left sides .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 2

x 2

Prepare the 2 right sides

Insert 2 large locking nuts into each of the right sides .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Join the left side and shelves

Position 2 shelves against each of the left sides as shown and secure with 4 screws .

Finished

front edge

Finished

front edge

Finished

front edge

Finished

front edge

plain

chipboard

surface

plain

chipboard

surface

Assembly Instructions

Step 4

Step 5

Prepare the plinths

Tap 2 wooden dowels into each plinth .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

x 2

Fit the plinths

Push a plinth onto each left side as shown and secure with screw .

Step 6

Fit the right sides

Push a right side onto each assembly as shown and secure with 5 screws .

Finished

front edge

Plain chipboard

surface

Plain chipboard

surface

Assembly Instructions

Step 7

Prepare the top

Screw 8 metal dowels into the top .

Note: Tighten metal dowels up fully against the panels.

2 3

Step 8

Fit the top

Push the 2 shelf assemblies down onto the top .

Use a screwdriver to tighten the 8 large locking nuts fitted to the inside of the side panels and .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

Carefully turn the desk the correct way up

2 3

Warning: The unit is heavy. Lift with care.

Assembly Instructions

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

and quote the reference numbers on the component pages.

Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

ALR2686

Step 9

Fit the bracket

To prevent possible overbalancing, we recommend that this unit is secured to a suitable wall by use of the bracket fitted underneath the top .

Fixings are not supplied, as they will need to suit the wall type and the length of screw will depend on the distance from the back edge of the unit to the wall.

Place the desk in its final position.

Fix the bracket underneath the top of the unit, flush to the back edge that is against the wall, using screw .

Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

Assembly is complete

This shows the bracket being fitted to the back edge on the left side of the top. You may fit it in a different position to suit

your requirements.

Warning: The unit is heavy. Lift with care.

WALL

Top of unit

+ 16 hidden pages