Argos Malibu - 5 Drawer Wide Chest ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 75cm

Depth - 40cm

Height - 92.5cm

Malibu - 5 Drawer Wide Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800

Issue 3 - 16/01/15

Important - Please read these instructions fully before starting assembly

282/2736

279/9247

287/2188

274/7536

275/6572

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 31kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the overbalance protector kit supplied or, an alternative fixing method of your choice.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Left Side (D2775A)

(911 x 394mm)

Right Side (D2776A)

(911 x 394mm)

Left Drawer Side (W370-124LH)

(370 x 124mm) x 5

Right Drawer Side (W370-124RH)

(370 x 124mm) x 5

8 9

Drawer Front (D2783A)

(710 x 156mm) x 5

Back Rail (D2779A)

(714 x 60mm) x 2

Plinth (D2778A)

(714 x 92mm)

Rail (D2780A)

(714 x 72mm)

Drawer Back (W682-124)

(682 x 124mm) x 5

Drawer Base (T693-367)

(693 x 367mm) x 5

Back (X829-738)

(829 x 738mm)

Top (D2774B)

(747 x 396mm)

Please check you have all the fittings listed below

Tools required

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Wooden dowel (F22) x 12

Metal dowel (F901) x 12

Large locking nut (F900) x 2

Small locking nut (F3) x 10

H I

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Nail (F51) x 22

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill (only use when drilling into walls)

25mm Screw (F50) x 10

Handle (F631) x 10

40mm Screw (F910) x 6

Plastic Nail (F91) x 4

9mm Screw (F73) x 20

Drawer runner (F1004) x 10

Wedgefix (F639) x 20

9mm Screw (F74) x 10

Knock-in Peg (F171GY) x 20

Strap Screw Washer x 2

Overbalance protector kit (F269) x 1

Assembly Instructions

If you have damaged or missing components, call the

Customer Helpline: 03456 400800 quoting the reference

numbers below

Step 1

x 5

Step 2

Prepare the 5 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

Attach the drawer sides to the drawer front

Push the left drawer sides . and right drawer sides . onto the back of the drawer front .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

+ 11 hidden pages