Argos Malibu - 3 Drawer Wide Chest ASSEMBLY INSTRUCTIONS

MADE IN

BRITAIN

Dimensions

Width - 75cm

Depth - 39.5cm

Height - 60.5cm

Malibu - 3 Drawer Wide Chest

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800

Issue 3 - 01/04/14

Important - Please read these instructions fully before starting assembly

275/8903

244/8914

274/4027

244/9061

268/4905

248/3632

Safety and Care Advice

Important - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 20.5kgs. Please lift with care.

• Check you have all the components and tools listed on pages 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your local authority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do not recommend the use of power drill/drivers for

inserting screws, as this could damage the unit. Only use hand screwdrivers.

• Safety note: It is recommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Components - Panels

Please check you have all the panels listed below

2

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

1 2

7

4

Left Side (D2821A)

(591 x 394mm)

Left Drawer Side (W370-124LH)

(370 x 124mm) x 3

Right Drawer Side (W370-124RH)

(370 x 124mm) x 3

Right Side (D2822A)

(591 x 394mm)

5

8 9

Top (D2774A)

(747 x 396mm)

Drawer Front (D2783A)

(710 x 156mm) x 3

Back Rail (D2779A)

(714 x 60mm)

Plinth (D2778A)

(714 x 92mm)

Rail (D2780A)

(714 x 72mm)

6

10

11

Drawer Back (W682-124)

(682 x 124mm) x 3

Drawer Base (T693-367)

(693 x 367mm) x 3

Back (X511-738)

(511 x 738mm)

12

3

Please check you have all the fittings listed below

Tools required

3

Components - Fittings

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Rule Scissors Hammer

Eye protection (when using a hammer or drill)

Cross-head screwdriver

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Electric drill (only use when drilling into walls)

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

A

Wooden dowel (F22) x 10

B

Metal dowel (F901) x 8

C

D

Large locking nut (F900) x 2

E

Small locking nut (F3) x 6

F

G

40mm Screw (F910) x 4

H

25mm Screw (F50) x 6

I

Nail (F51) x 16

Knock-in Peg (F171GY) x 12

Handle (F631) x 6

N

L

Plastic Nail (F91) x 4

J

9mm Screw (F74) x 6

K

9mm Screw (F73) x 12

M

Wedgefix (F639) x 12

Drawer runner (F1004) x 6

Assembly Instructions

4

If you have damaged or missing components, call the

Customer Helpline: 08456 400800 quoting the reference

numbers below

Step 1

Step 2

Prepare the 3 drawer fronts

Screw 2 metal dowels into each of the drawer fronts .

Note: Tighten the metal dowels up fully against the panels.

B

7

Prepare the drawer sides

Insert a small locking nut into the hole shown on the left drawer side and the right drawer side .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

Step 3

F

8

9

Attach the drawer sides to the drawer fronts

Push the left drawer sides . and right drawer sides . onto the back of the drawer fronts .

Turn the small locking nuts on the left drawer side and right drawer side .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

8 9

7

F

8 9

x 3

B

F

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer sides.

Note: The locking nuts can be on either surface of the drawer sides. Make sure that the small groove is on the inside, as shown.

F

8

9

8

B

7

Assembly Instructions

5

Step 4

7

C

x 3

C

9

8

11

9

8

10

N

H

N

H

7

M

Fit the drawer base

Slide the drawer base down the grooves in the drawer sides and and down into the groove in the drawer front .

Step 5

Fit the drawer back

Fit the drawer back between the drawer sides and . Make sure that the drawer base fits into the groove in the drawer back .

Hold the drawer back in position and tap the knock-in pegs through the holes in the drawer sides and .

Step 6

11

8 9

7

10

8 9

11

10

C

Attach the handles

Attach 2 handles to each of the drawer fronts . using screws .

Note: Do not overtighten the screw.

N

H

7

8 9

Step 7

Fit the wedgefixes

Turn the drawer assemblies over and slide 4 wedgefixes into the front and back grooves, as shown, and tighten up the screws.

M

Finished

front edge

Assembly Instructions

6

Step 8

A

Finished

front edge

Finished

front edge

K

I

K

I

Prepare the left side

a: Place 3 runners on

the left side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the left side .

Insert a large locking nut into the left side . .

Note: The arrow on the locking nuts must point towards the hole in the edge of the panel.

Tap a wooden dowel into the left side .

Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.

1

K

1

I

K

E

a:

b:

10mm

A

E

1

A

1

K

I

K

I

Assembly Instructions

7

Step 9

A

Prepare the right side

a: Place 3 runners on

the right side as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner

back the other way and fit the 2nd screw into the corresponding hole in the right side .

Insert a large locking nut into the right side . .

Tap a wooden dowel into the right side .

2

K

2

I

E

2

A

2

Finished

front edge

K

I

Finished

front edge

Finished

front edge

K

I

K

I

K

I

K

E

2

a:

b:

A

Prepare the plinth, rail and back rail

Tap 2 wooden dowels into the plinth .

Tap 4 wooden dowels into the rail .

Tap 2 wooden dowels into the back rail .

A

Plain chipboard

surface

Plain chipboard

surface

A

The colour of the back rail may differ from the

main unit colour or may

be plain chipboard.

A

4

A

5

A

6

4

6

5

Finished

front edge

Step 10