Page 1
Malibu - 3 Drawer 2+2 Door Robe
Assembly Instructions - Please keep for future reference
563/6307
553/4038
544/3985
563/7038
544/3930
More help is available throughout this booklet by scanning
in the QR codes or typing in the links
Dimensions
Width - 145.9cm
Depth - 49.8cm
Height - 180.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
MADE IN
BRITAIN
Issue 2 - 24/06/16
Page 2
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 102kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2, 3, 4 and 5.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
Care and maintenance
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the 2 overbalance
protector kits supplied or, an
alternative fixing method of your
choice.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
When applicable, remove any protective film
from the panels before they are used
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Page 3
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
1
(70.8 x 15.7cm)
5
Drawer Base
(T676-447)
(67.6 x 44.7cm)
(DF5996)
x 3
x 3
6 Base
Left Drawer
2Drawer Front
Side
(WB450-130LH)
(45 x 13cm)
Top (DF7369)
(145.9 x 49.8cm)
3 Drawer Back
x 3
When applicable, remove any
protective film before use
Right Drawer
Side
(WB450-130RH)
(45 x 13cm)
x 3
7
4
(W665-130)
(66.5 x 13cm)
(DF7370)
(142.5 x 49.4cm)
x 3
8 9
Left Side
(179 x 49.6cm)
(DF7367)
Right Side (DF7368)
(179 x 49.6cm)
Left Divider (DF7373)
10 Right Divider
(168.25 x 47.4cm)
11
(168.25 x 47.4cm)
(DF7374)
2
Page 4
Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below
12 Plinth
(DF7375)
(142.5 x 9.2cm )
15 Narrow Shelf
(34.05 x 47.2cm)
x 2
(DF7372)
x 2
16 Horizontal
(71.4 x 47.2cm)
13 Cross Rail
(71.4 x 6cm)
(DF5862)
x 2
When applicable, remove any
protective film before use
(DF5858)
17 Top Rail
(34.05 x 6cm)
(DF7356)
x 2
14 Back Rail
(34.05 x 9.2cm)
(DF7376)
x 2
18 Left Door
(119.6 x 35.25cm)
21 Small Back
(170.9 x 36cm)
3
(DF6012)
(X1709-360)
x 2
19 Right Door
(119.6 x 35.25cm)
22 Large Back
(170.9 x 72.7cm)
(DF6013)
(X1709-727)
20 Large Door
(167.6 x 35.25cm)
23
Long Hanging Rail
(70.8cm long)
24
Short Hanging Rail (FHR334)
(33.4cm long)
(DF7377)
x 2
x 2
(FHR708)
Page 5
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the fittings listed below
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel
D
19mm
Screw (F461) x 6
(F545) x 6
Main Fittings Bag
A
Quickfit dowel
F
13mm Screw
(F545) x 28
(F63) x 18
B
Large locking cam nut (F607) x 6
E
15mm Screw
B
Large locking cam nut (F607) x 36
9mm Screw (F73) x 18
(F284) x 6
C
Knock-in Peg
F
13mm Screw (F63) x 12
D
19mm
40mm Screw
Screw (F461) x 4
HG
(F171GY) x 12
(F910) x 4
I
Nail (F51) x 44
L
Door Buffer (F137) x 6
O
Double metal dowel
(F566) x 4
J
Plastic Nail (F91) x 6
M
Wooden dowel (F22) x 48
P
Nail screw
(F277) x 12
K
Rail Holder (F891) x 6
N
Large wooden dowel
Q
Back holder (F276) x 12
(F40) x 10
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
4
Page 6
Components - Fittings
Individual Fittings Bags
R
Overbalance protector
F474) x 2
kit (
S
Handle
(F418) x 10
T
Pre-mounted
hinge (
U
Drawer Brace (F427) x 3
M
V
V
V
a
b
c
CL
DL
F419) x 12
436mm long
450mm long
CL Runner
CR
CR Runner
DL Runner
(F608) x 3
(F609) x 3
(F610) x 3
d
V
Tools required
Rule
Rule
5
Spirit
level
ScissorsSquare
DR
DR Runner
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Hammer Bradawl
(F611) x 3
Electric drill
(only use
when drilling
into walls)
Step
ladder
Page 7
Assembly Instructions
Step 1
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7
Prepare the drawer
sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
B
2
3
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
sides and the right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
2
3
Standard Drawer Box Assembly
hps://www.youtube.com/watch?v=HclfJdkm-Lg
a:
B
2
B
x 3 x 3
b:
A
2
A
x 3 x 3
B
3
3
A
Step 2
Fit the drawer sides
to the 3 drawer fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 3
drawer fronts .
Turn the large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
2
3
1
B
11
B
x 3
3
2
1
6
Page 8
Assembly Instructions
Step 3
Fit the drawer bases
Slide a drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
1
5
32
Step 4
Fit the drawer backs
Fit a drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
2 3
4
4
5
5
3
x 3
2
x 3
C
C
2
1
C
C
4
3
5
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
C
2 3
Step 5
Fit the handles
Attach 2 handles to
each drawer front
using screws .
7
S
1
D
4
D
D
1
S
S
x 3
Page 9
Assembly Instructions
Step 6
E
Fit the drawer braces
Turn the 3 drawer
assemblies over and
hook a drawer brace
U
onto the bottom edge of
the drawer back .
4
Fix it to the drawer front
. and drawer back
1 4
using 2 screws .
E
U
1
E
E
U
4
x 3
E
U
Step 7
Fit runners to the
drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
1
to mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
V c
2
F
V d
3
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Runners must be
pushed up against
the drawer front
F
F
DL
1
F
DL
2
x 3
F
3
DR
V d
V c
8
Page 10
Assembly Instructions
Step 8
Prepare the left divider
a: Fit 3 CL runners
to the left divider .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
G
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
V a
Fit a rail holder to the
left divider through
10
the top hole with screw
and into the mark hole
drilled in the left divider.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
c: Insert 2 large locking
cam nuts into the left
divider .
Push 2 of the quickfit
dowels as far as they
will go into the left
divider .
Tap 6 wooden dowels
into the left divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
9
B
10
A
10
V a
10
G
F
K
F
M
10
Use the Main Fittings Bag for Steps 8 - end
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
1st
front edge
Finished
a:
F
front edge
Finished
b:
c:
M
M
M
G
screw
V a
CL
Finished
front edge
G
G
G
G
CL
CL
F
F
F
CL
CL
CL
CL
G
G
V a
F
CL
CL
CL
G
G
V a
G
V a
V a
Finished
front edge
Finished
front edge
10
10
10
F
K
F
F
K
B
A
B
10mm
F
K
A
M
B
M
M
A
M
Page 11
Assembly Instructions
Step 9
1st
Prepare the right
divider
screw
V b
G
front edge
Finished
a: Fit 3 CR runners
to the right divider .
The 1st screw uses
G
V b
11
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
G
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
F
the hole at the top of the
runner .
Fit a rail holder to the
right divider through
the top hole with screw
V b
K
11
F
and into the mark hole
drilled in the right divider.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
F
the lower hole.
CR
a:
b:
G
G
G
CR
Finished
F
CR
G
G
CR
V b
CR
G
CR
V b
V b
F
F
CR
G
G
G
F
front edge
11
11
Finished
front edge
F
K
Finished
front edge
F
c: Insert 2 large locking
cam nuts into the
right divider .
Push 2 of the quickfit
dowels as far as they
will go into the right
divider .
Tap 6 wooden dowels
into the right divider .
B
11
A
11
M
11
M
M
c:
M
A
B
11
CR
CR
CR
B
Finished
front edge
A
M
B
M
M
A
10
Page 12
Assembly Instructions
Step 10
Prepare the other
surface of the dividers
Turn both of the dividers over
F
F
Turn the left divider
and right divider over
Fit a rail holder to the
left divider and the
right divider through
the top hole with screw
K
10
11
F
and into the mark hole.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
F
the lower hole.
10
Finished
front edge
K
Finished
front edge
11
F
F
K
Step 11
Prepare just 1 of the
horizontals
Insert 4 large locking
cam nuts into 1 of the
horizontals .
11
B
16
B
B
B
B
16
Finished
front edge
Page 13
Assembly Instructions
Step 12
Fit the horizontal to
the right divider
Push the horizontal
onto the right divider .
16
11
O
B
B
Tap 2 double metal
dowels through the
right divider and into
the horizontal until
O
11
16
they ‘’bottom out’’.
Turn the 2 large locking
cam nuts fitted to the
horizontal clockwise
B
16
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
CR
Finished
front edge
O
O
11
16
Finished
front edge
Step 13
Fit 3 large wooden
dowels
Tap 3 large wooden
dowels through the
right divider and into
the horizontal until
they ‘’bottom out’’.
N
11
16
N
N
N
11
CR
16
12
Page 14
Assembly Instructions
Step 14
A
Prepare the other
horizontal
Insert 4 large locking
cam nuts into the
horizontal .
B
16
M
A
M
M
B
B
B
B
B
16
A
Push 4 of the quickfit
dowels as far as they
A
will go into the horizontal
. .
16
Tap 6 wooden dowels
into the horizontal .
M
16
Step 15
Fit the horizontal to
the right divider
Push the horizontal
onto the right divider .
Turn the 2 large locking
cam nuts fitted to the
horizontal clockwise
B
16
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
16
11
Finished
front edge
M
M
A
Carcase Assembly
hps://www.youtube.com/watch?v=9C7tgv5xnbE
11
16
CR
Finished
front edge
A
M
Step 16
Fit the cross rail
Push the cross rail up
against the right divider
. .
11
Tap 2 large wooden
dowels through the
right divider and into
cross rail until they
N
11
13
‘’bottom out’’.
13
13
N
N
11
13
CR
Finished
front edge
Page 15
Assembly Instructions
Step 17
Fit the left divider
Push the left divider
onto the assembly.
10
Top of unit
Tap 2 double metal
dowels through the
left divider and into
the horizontal at the
O
10
16
top of the unit until they
‘’bottom out’’.
Turn the 4 large locking
cam nuts fited to the
2 horizontals
B
16
clockwise as far as
they will go to secure
the panels.
Important: Make
sure there is no gap
between the fitted
panels.
Step 18
Fit 2 large wooden
dowels
Tap 2 large wooden
dowels through the
left divider and into
the cross rail until
they ‘’bottom out’’.
N
10
13
16
13
O
16
CR
16
16
CR
10
O
Finished
front edge
13
13
10
N
N
Step 19
Fit 3 more large
wooden dowels
Tap 3 large wooden
dowels through the
left divider and into
the horizontal until
they ‘’bottom out’’.
N
10
16
16
13
N
10
CR
N
N
14
Page 16
Assembly Instructions
Step 20
Prepare the 2 top rails
Tap 2 wooden dowels
M
into each of the 2 top
rails .
17
Step 21
Fit the 2 top rails
Push 1 of the top rails
onto the left divider .
Push the other top rail
onto the right divider .
17
10
17
11
Finished
front edge
Finished
front edge
17
17
x 2
M
11
M
13
Step 22
Prepare 1 of the
narrow shelves
Insert 4 large locking
cam nuts into the
narrow shelf .
Push 2 of the quickfit
dowels as far as they
will go into the narrow
shelf .
B
15
A
15
CR
Finished
front edge
10
Finished
front edge
B
B
B
15
B
x 1
A
M
M
M
A
17
Tap 3 wooden dowels
into the narrow shelf .
15
M
15
Page 17
Assembly Instructions
Step 23
Fit the narrow shelf
Push the narrow shelf
onto the left divider .
15
10
Turn the 2 large locking
cam nuts fited to the
narrow shelf
B
15
clockwise as far as they
will go to secure the
panels.
Important: Make
sure there is no gap
between the fitted
panels.
Step 24
Prepare the other
narrow shelf
Insert 4 large locking
cam nuts into the
narrow shelf .
Push 2 of the quickfit
dowels as far as they
will go into the narrow
shelf .
B
15
A
15
A
M
CR
M
M
Finished
front edge
13
10
A
B
B
B
B
15
15
Finished
front edge
Tap 3 wooden dowels
into the narrow shelf .
M
15
Step 25
Fit the narrow shelf
Push the narrow shelf
onto the right divider .
Turn the 2 large locking
cam nuts fited to the
narrow shelf
B
15
clockwise as far as they
will go to secure the
panels.
Important: Make
sure there is no gap
between the fitted
panels.
15
11
15
11
CR
13
16
Page 18
Assembly Instructions
Step 26
Prepare the base
Insert 4 large locking
cam nuts into the
base .
B
7
Push 4 of the quickfit
dowels as far as they
will go into the base .
Tap 6 wooden dowels
into the base .
A
7
M
7
Step 27
Fit the base
Push the base onto
the assembly and secure
it using 4 screws .
7
H
A
M
M
M
A
B
B
Finished
front edge
B
7
B
A
M
M
M
A
13
H
H
Step 28
Prepare the back rails
Insert 2 large locking
cam nuts into each of
the 2 back rails .
Push 2 of the quickfit
dowels as far as they
will go into each of the 2
back rails .
B
14
A
14
CR
7
Polystyrene
H
block
Note: To make it easier to fit the
top and base panels, place
H
Finished
front edge
polystyrene blocks from the
packaging underneath the divider
panels to raise the assembly.
B
M
A
B
14
Finished
front edge
x 2
Tap 2 wooden dowels
into each of the 2 back
rails .
14
17
M
M
A
Page 19
Assembly Instructions
Step 29
Prepare the right side
Fit a rail holder to the
right side through the
top hole with screw
K
9
F
and into the mark hole
drilled in the right side.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
F
the lower hole.
c: Insert 2 large locking
cam nuts into the
right side .
Push 2 of the quickfit
dowels as far as they
will go into the right side
9
. .
B
9
A
B
A
F
F
K
9
Finished
front edge
M
B
M
M
A
Tap 3 wooden dowels
into the right side .
M
9
Step 30
Fit the back rail to the
right side
Push the back rail
onto the right side .
Turn the large locking
cam nut fitted to the
back rail clockwise
B
14
as far as it will go to
secure the panels.
14
9
Finished
front edge
14
9
Finished
front edge
Important: Make sure
there is no gap between
the fitted panels.
18
Page 20
Assembly Instructions
Step 31
Fit the right side
Push the right side
onto the assembly.
Turn the 5 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make
sure there is no gap
between the fitted
panels.
B
9
14
9
11
CR
Step 32
Prepare the 2 plinths
Insert 2 large locking
cam nuts into the
each of the 2 plinths . .
Push 2 of the quickfit
dowels as far as they
will go into the each of
the 2 plinths .
Tap 2 wooden dowels
into the each of the 2
plinths .
19
B
A
12
12
12
M
M
A
B
x 2
B
12
A
M
Page 21
Assembly Instructions
Step 33
Prepare the left side
Fit a rail holder to the
left side through the
8
top hole with screw
K
F
and into the mark hole
drilled in the left side.
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
F
the lower hole.
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
8
. .
Tap 3 wooden dowels
into the left side .
B
8
A
M
8
Finished
front edge
B
A
F
F
K
8
M
B
M
M
A
Step 34
Fit the back rail to the
left side
Push the back rail
onto the left side .
Turn the large locking
cam nut fitted to the
back rail clockwise
B
14
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
14
8
Finished
front edge
Finished
front edge
14
8
20
Page 22
Assembly Instructions
Step 35
Fit the 2 plinths
Push the plinths onto
the right side .
12
9
Turn the large locking
cam nut fitted to the
to each of the plinths
B
12
clockwise as far as they
will go to secure the
panels.
Important: Make sure
there is no gap between
the fitted panels.
CR
9
12
12
Note: Support the plinths
until the left side has been
fitted in the next step.
21
Page 23
Assembly Instructions
Step 36
Fit the left side
Push the left side
8
onto the assembly.
Turn the 7 large locking
cam nuts clockwise
B
as far as they will go to
secure the panels.
Important: Make
sure there is no gap
between the fitted
panels.
CR
14
10
12
8
12
Finished
front edge
Step 37
Fit the top
Push the top onto
the assembly.
Turn the 8 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make
sure there is no gap
between the fitted
panels.
6
B
9
11
6
10
8
CR
22
Page 24
Assembly Instructions
Step 38
Fit the back panels
a: Square up the unit by
making sure that
measurement x:x equals
y:y.
y
y
22
21
Place the large back
and the 2 small backs
down onto the unit as
shown.
Make sure that
the 3 backs are
pushed up tight
against each
other and that
they meet over
the back edges
of the dividers.
Squaring up a Robe and tting the Back Panel
www.youtube.com/watch?v=udEKmXmPEW0
The measurement from top corner X to bottom corner X must be
a:
equal to the measurement from top corner Y to bottom corner Y
b:
x
I
21
22
CR
Note: Do not
nail where the
backs meet.
21
yy
b: Nail around
the outside edges
of the 3 backs.
Note: Do not nail where
the backs meet. Nails
should be spaced about
150mm apart.
I
Step 39
Secure the backs
Tap the nail screws
through the back holders
Q
. and down between
the backs and
into the back edge
of the divider.
Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.
21 22
P
Q
P
x
P
Q
x 6
QP
+
21
22
21
CR
Q
x 6
QP
+
23
Page 25
Assembly Instructions
Step 40
Fit the 6 plastic nails
Tap 2 plastic nails
J
into the bottom edge of
each side and as
8 9
shown.
J
9
J
Tap 1 plastic nail into
each plinth as
12
J
shown.
Carefully stand the
unit up for the next
step.
Warning: The
robe is heavy.
Lift with care.
CR
12
J
12
J
J
8
J
Step 41
Fit the hanging rails
Push the long hanging
23
rail and 2 short
hanging rails into the
rail holders .
24
K
24
23
24
23
24
K
24
Page 26
Assembly Instructions
Step 42
Fit the drawers
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Fixing Bottom Mounted Runners
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Side
panel
Drawer
Step 43
Prepare the 4 doors
Push fit 3 hinges into
the left door , the right
door and the 2 large
19
doors .
Secure each hinge by
tightening up its 2
screws.
20
T
18
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
T
T
T
T
T
20
T
19
T
T
18
T
x 2
25
Page 27
Assembly Instructions
Step 44
Fit the doors and the
handles
2 people are needed
here
Fit 1 door , and
. at a time, by lining up
the 2 screws in the top
hinge with the 2 holes
at the top of the panel
and push them in.
Tighten the 2 screws on
the hinge.
Fix the bottom hinge
next, followed by the
other hinge.
Attach a handle to
each door using screws
. .
D
182019
T
S
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
Press the screws into
the holes in the panels
T
When the hinges have
been pushed in,
tighten up their screws
T
Note: Fit the
top hinge 1st
20
20
19
18
S
S
S
D
S
26
Page 28
Assembly Instructions
Step 45
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
Pre-mounted Hinge Fitting & Adjustment
hps://www.youtube.com/watch?v=b4NeCGnpjP8
a:
b:
A
A
c:
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
B
d:
C
27
Page 29
Assembly Instructions
Step 46
Fit the 2 overbalance
protector kits
To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting of
the 2 overbalance
protector kits to the
unit, or an alternative
fixing method of your
choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
R
R
R
R
R
Take care when
Note:
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
28
Page 30
Assembly Instructions
Step 47
Fit the door buffers
L
50mm
Stick a door buffer
onto the top corner of
each door , and
about 50mm in from the
edge.
The other 2 door buffers
are spare and you can
use them wherever
needed.
Assembly is complete
18 19 20
L
L
20
19
18
20
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: Help@ClickSpares.co.uk (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
29
Page 31
Page 32
ALR3319
Loading...