MADE IN
BRITAIN
Dimensions
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 4 - 04/09/14
Important - Please read these instructions fully before starting assembly
147/1999
157/6760
145/7229
Atlas - Triple Robe Carcass
Width - 150cm
Depth - 59.5cm
Height - 212.5cm
IMPORTANT
The unit MUST be fixed to a wall using
both of the brackets supplied.
There is the option of
purchasing an Internal 3
Drawer Chest that can be
placed inside your Robe
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 65kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Universal End (D2396A)
(2074 x 591mm) x 2
5
2
Top/Base (D2652A)
(1499 x 592mm) x 2
Large Fixed Shelf (D2397A)
(968 x 590mm)
Upright (D2653A)
(2074 x 591mm)
4
3
Small Fixed Shelf (D2654A)
(484 x 590mm)
Small Back (X2100-504)
(2100 x 504mm)
Large Back (X2100-988)
(2100 x 988mm)
Large Hanging Rail (FHR960)
(960mm long) x 2
7
Small Hanging Rail (FHR476)
(476mm long) x 2
6
8 9
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 8
C
D E
Large locking
nut (F900) x 8
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
Rail Holder
(F891) x 8
Allen Key (F36) x 1
50mm Screw (F49) x 18
19mm Screw (F461) x 6
Hinge (F328) x 12
25mm Screw (F50) x 6
13mm Screw (F63) x 38
13mm Screw (F79) x 2
Bracket (F327) x 2
Feet (F854) x 6
P
Nail screw (F277) x 6
Handle (F323) x 3
Q
Back holder (F276) x 6
* These can also be round
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Are you fitting 1 or 2
hanging rails or, a
shelf pack?
If you are just
fitting 1
hanging rail to
this side, the
large fixed
shelf will need
to go here.
If you are just
fitting 1
hanging rail or
the shelf pack
to this side,
the small fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the large fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the small fixed
shelf will need
to go here.
Finished
front edge
Assembly Instructions
5
Step 2
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
2
2
J
K
J
K
B
Refer to Step 1 and ONLY FOLLOW THIS STEP if you
are fitting the small fixed shelf near the top of the unit.
Note: If you have purchased a
shelf pack, do not fit the rail holder.
B
B
K
Turn the upright over and
carry out either step 4 or 5
2
Please ensure you have your panel in exactly the
same orientation as the picture above and use the
2 inside holes for screws B as shown in the picture.
Assembly Instructions
6
Step 3
Finished
front edge
K
B
B
K
J
K
J
K
B
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holders ,
screw through their top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using their lower hole.
B
K
J
J
2
2
Refer to Step 1 and ONLY FOLLOW THIS STEP if you are
fitting the small fixed shelf near the middle of the unit.
Turn the upright over and
carry out either step 4 or 5
2
Please ensure you have your panel in exactly the
same orientation as the picture above and use the
2 inside holes for screws B as shown in the picture.
Assembly Instructions
7
Step 4
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
2
2
Refer to Step 1 and ONLY FOLLOW THIS STEP if you
are fitting the large fixed shelf near the top of the unit.
B
B
Finished
front edge
Refer to Step 1 and ONLY FOLLOW THIS STEP if you are
fitting the large fixed shelf near the middle of the unit.
B
B
K
Finished
front edge
Step 5
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holders ,
screw through their top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using their lower hole.
B
K
J
J
2
2
K
2
2
K
Finished
front edge
A
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 6
Prepare the large
fixed shelf
Tap 2 wooden dowels
into the large fixed shelf
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the large
fixed shelf .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
C
4
4
C
10mm
A
C
C
A
C
C
4
Join the large fixed
shelf to the upright
Push the large fixed shelf
. onto the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the large fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4 2
C
C
4
Step 7
4
If you have fitted the 2
metal dowels in this
position, the large
fixed shelf will go here.
B
C
2
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 8
Prepare the small
fixed shelf
Insert 4 large locking
nuts into the small
fixed shelf .
C
5
Join the small fixed
shelf to the upright
Push the small fixed
shelf onto the upright
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the small fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
2
C
C
5
Step 9
C
C
C
C
5
Finished
front edge
If you have fitted the 2
metal dowels in this
position, the small
fixed shelf will go here.
2
5
The following assembly diagrams will show the 2 fixed shelves
at the top end of the unit.
You may have fitted 1 or both of them in the middle of the unit.
Assembly Instructions
10
Step 10
Step 11
Prepare the right end
Screw 2 metal dowels
into the right end .
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
it is fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
1
B
1
1
B
B
K
1
Finished
front edge
J
K
J
K
ONLY FOLLOW THIS STEP if you have fitted the
small fixed shelf near the top of the upright.
ONLY FOLLOW THIS STEP if you have fitted the
small fixed shelf in the middle of the upright.
B
B
K
1
Finished
front edge
Prepare the right end
Screw 2 metal dowels
into the right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
they are fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
K
J
J
1
J
K
J
K
B
K
Finished
front edge
Assembly Instructions
11
Step 12
Step 13
Join the right side to
the small fixed shelf
Push the right side
onto the small fixed shelf
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the small fixed shelf .
5
1
C
5
1
5
Finished
front edge
Prepare the left end
Screw 2 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
B
B
1
1
K
1
J
ONLY FOLLOW THIS STEP if you have fitted the
large fixed shelf near the top of the upright.
Note: If you have purchased a shelf pack,
do not fit the rail holder.
Assembly Instructions
12
Step 14
Step 15
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that they
are fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
B
B
1
1
J
K
J
K
B
K
1
K
ONLY FOLLOW THIS STEP if you have fitted the
large fixed shelf in the middle of the upright.
Join the left side to
the large fixed shelf
Push the left side
onto the large fixed shelf
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the large fixed shelf .
4
1
C
4
Finished
front edge
4
1
Finished
front edge
Finished
front edge
Assembly Instructions
Step 16
Prepare the base
Screw the 6 feet into
the shallow mark holes
on the base using
screws .
M
3
G
G
M
M
M
M
M
M
Finished
front edge
3
Step 17
Fit the base
Attach the base to
the ends and the
upright using 9
screws and tighten
them using the allen key
. .
3
1
2
F
E
1
1
2
3
13
E
F
F
F
F
F
F
F
F
F
Unit colour on
the top surface
F
F
F
F
F
F
F
F
F
Assembly Instructions
14
Step 18
1
1
2
Fit the top
Attach the top to the
ends and the upright
. using 9 screws
and tighten them using
the allen key .
3
1
2
F
E
E
3
Finished
front edge
Finished
front edge
Assembly Instructions
Step 19
15
yy
y
x
x
D
b:
Fit the back panels
a: Square up the unit by
making sure that the
measurement x:x equals
y:y.
Place the small back
and large back ,
coloured surface facing
down, onto the unit as
shown.
Make sure that the 2
backs are pushed up
tight against each other
and that they meet in the
centre of the divider’s
back edge.
b: Nail around
the outside edges of
the 2 backs.
Note: Do not nail where
the 2 backs meet.
c: Push the nail screws
. through the back
holders and tap them
down between the small
back and large back
. and into the back
edge of the upright .
Keep tapping the nail
screws in until the
back holders dig into
the small and large back.
Stand the unit up for
the next step.
8
9
D
P
Q
8
9
2
P
Q
Warning: The
unit is heavy.
Lift with care.
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
QP
+
c:
8
9
P
Q
8
9
Q
Note: These can
also be round
Note: If ever you need to take
the backs off to dismantle the
unit, the nail screws can be
taken out using a screwdriver.
P
Q
Assembly Instructions
16
Step 20
K
Fit the hanging rail(s)
If required, push the
hanging rail(s) and
into the rail holders
fitted to the panels.
6 7
K
7
6
L
I
Assembly Instructions
Step 21
17
Top of Unit
WALL
WALL
Back of Unit
L
Fit the 2 brackets
To prevent possible
overbalancing, we
recommend that this unit
is secured to a suitable
wall by use of the 2
brackets fitted to the
top of the unit.
Fixings are not supplied,
as they will need to suit
the wall type and the
length of screws will
depend on the distance
from the back of the unit
to the wall.
Fix the brackets
loosely onto the top of
the unit using screws
and mark the wall for the
wall fixing.
Swivel the brackets
away from the wall and
drill the holes in the wall
using a suitable drill bit
and fit your wall fixings.
Swivel the brackets
back and fix the brackets
to the wall, then tighten
the screws .
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
Warning: The
unit is heavy.
Lift with care.
L
L
I
L
L
I
L
L
NOTE
The unused fittings from this assembly are used to fit the doors.
Please refer to the instructions packed with the doors.
IMPORTANT
This unit MUST be fixed to a wall
using both of the brackets supplied.
The unit must be level and square
before fitting the brackets.
Assembly Instructions
18
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 22
Chest
Loose
Shelf
Loose
Shelf
Loose
Shelf
Door
Fit the doors and, if
required, the shelf
pack and internal
chest
Please refer to the
instructions packed with
the doors, shelf pack or
internal chest.
Door
Door
IMPORTANT
The unused fittings from this assembly are used to fit the doors.
Please refer to the instructions packed with the doors.
ALR2956
MADE IN
BRITAIN
Dimensions
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 5 - 21/01/15
Important - Please read these instructions fully before starting assembly
147/1999
157/6760
145/7229
Atlas - Triple Robe Carcass
Width - 150cm
Depth - 59.5cm
Height - 212.5cm
IMPORTANT
The unit MUST be fixed to a wall using both
of the overbalance protector kits supplied.
There is the option of
purchasing an Internal 3
Drawer Chest that can be
placed inside your Robe
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 65kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using both of
the overbalance protector kits
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
2
1
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Universal End (D2396A)
(2074 x 591mm) x 2
5
2
Top/Base (D2652A)
(1499 x 592mm) x 2
Large Fixed Shelf (D2397A)
(968 x 590mm)
Upright (D2653A)
(2074 x 591mm)
4
3
Small Fixed Shelf (D2654A)
(484 x 590mm)
Small Back (X2100-504)
(2100 x 504mm)
Large Back (X2100-988)
(2100 x 988mm)
Large Hanging Rail (FHR960)
(960mm long) x 2
7
Small Hanging Rail (FHR476)
(476mm long) x 2
6
8 9
Please check you have all the fittings listed below
3
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 8
C
D E
Large locking
nut (F900) x 8
F
G H I
L
O
Nail (F51) x 40
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
K
N
Rail Holder
(F891) x 8
Allen Key (F36) x 1
50mm Screw (F49) x 18
19mm Screw (F461) x 6
Hinge (F328) x 12
25mm Screw (F50) x 6
13mm Screw (F63) x 38
Feet (F854) x 6
P
Handle (F323) x 3
Nail screw (F277) x 6
Back holder (F276) x 6
* These can also be round
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 2
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Are you fitting 1 or 2
hanging rails or, a
shelf pack?
If you are just
fitting 1
hanging rail to
this side, the
large fixed
shelf will need
to go here.
If you are just
fitting 1
hanging rail or
the shelf pack
to this side,
the small fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the large fixed
shelf will need
to go here.
If you are fitting
2 hanging rails
to this side,
the small fixed
shelf will need
to go here.
Finished
front edge
Assembly Instructions
5
Step 2
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
2
2
J
K
J
K
B
Refer to Step 1 and ONLY FOLLOW THIS STEP if you
are fitting the small fixed shelf near the top of the unit.
Note: If you have purchased a
shelf pack, do not fit the rail holder.
B
B
K
Turn the upright over and
carry out either step 4 or 5
2
Please ensure you have your panel in exactly the
same orientation as the picture above and use the
2 inside holes for screws B as shown in the picture.
Assembly Instructions
6
Step 3
Finished
front edge
K
B
B
K
J
K
J
K
B
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holders ,
screw through their top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using their lower hole.
B
K
J
J
2
2
Refer to Step 1 and ONLY FOLLOW THIS STEP if you are
fitting the small fixed shelf near the middle of the unit.
Turn the upright over and
carry out either step 4 or 5
2
Please ensure you have your panel in exactly the
same orientation as the picture above and use the
2 inside holes for screws B as shown in the picture.
Assembly Instructions
7
Step 4
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
2
2
Refer to Step 1 and ONLY FOLLOW THIS STEP if you
are fitting the large fixed shelf near the top of the unit.
B
B
Finished
front edge
Refer to Step 1 and ONLY FOLLOW THIS STEP if you are
fitting the large fixed shelf near the middle of the unit.
B
B
K
Finished
front edge
Step 5
Prepare the upright
Screw 2 metal dowels
into the upright .
Note: Tighten the metal
dowels up fully against
the panels.
Note: If you have
purchased a shelf pack,
do not fit the rail holder.
To fit the rail holders ,
screw through their top
hole with screw and
into the shallow mark
hole drilled in the upright
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using their lower hole.
B
K
J
J
2
2
K
2
2
K
Finished
front edge
A
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 6
Prepare the large
fixed shelf
Tap 2 wooden dowels
into the large fixed shelf
. .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the large
fixed shelf .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
C
4
4
C
10mm
A
C
C
A
C
C
4
Join the large fixed
shelf to the upright
Push the large fixed shelf
. onto the upright .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the large fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4 2
C
C
4
Step 7
4
If you have fitted the 2
metal dowels in this
position, the large
fixed shelf will go here.
B
C
2
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 8
Prepare the small
fixed shelf
Insert 4 large locking
nuts into the small
fixed shelf .
C
5
Join the small fixed
shelf to the upright
Push the small fixed
shelf onto the upright
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the small fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
5
2
C
C
5
Step 9
C
C
C
C
5
Finished
front edge
If you have fitted the 2
metal dowels in this
position, the small
fixed shelf will go here.
2
5
The following assembly diagrams will show the 2 fixed shelves
at the top end of the unit.
You may have fitted 1 or both of them in the middle of the unit.
Assembly Instructions
10
Step 10
Step 11
Prepare the right end
Screw 2 metal dowels
into the right end .
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
it is fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
1
B
1
1
B
B
K
1
Finished
front edge
J
K
J
K
ONLY FOLLOW THIS STEP if you have fitted the
small fixed shelf near the top of the upright.
ONLY FOLLOW THIS STEP if you have fitted the
small fixed shelf in the middle of the upright.
B
B
K
1
Finished
front edge
Prepare the right end
Screw 2 metal dowels
into the right end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the right
end . Make sure that
they are fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
K
J
J
1
J
K
J
K
B
K
Finished
front edge
Assembly Instructions
11
Step 12
Step 13
Join the right side to
the small fixed shelf
Push the right side
onto the small fixed shelf
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the small fixed shelf .
5
1
C
5
1
5
Finished
front edge
Prepare the left end
Screw 2 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the rail holder ,
screw through its top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that it is
fitted straight, in line with
the panel edges and
then fit another screw
using the lower hole.
B
K
J
B
B
1
1
K
1
J
ONLY FOLLOW THIS STEP if you have fitted the
large fixed shelf near the top of the upright.
Note: If you have purchased a shelf pack,
do not fit the rail holder.
Assembly Instructions
12
Step 14
Step 15
Finished
front edge
Prepare the left end
Refer to step 1 and, if
you have chosen to fit 2
hanging rails, screw 2
metal dowels into the
left end .
Note: Tighten the metal
dowels up fully against
the panels.
To fit the 2 rail holders
screw through the top
hole with screw and
into the shallow mark
hole drilled in the left end
. . Make sure that they
are fitted straight, in line
with the panel edges and
then fit another screw
using the lower hole.
B
K
J
J
B
B
1
1
J
K
J
K
B
K
1
K
ONLY FOLLOW THIS STEP if you have fitted the
large fixed shelf in the middle of the upright.
Join the left side to
the large fixed shelf
Push the left side
onto the large fixed shelf
. .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the large fixed shelf .
4
1
C
4
Finished
front edge
4
1
Finished
front edge
Finished
front edge
Assembly Instructions
Step 16
Prepare the base
Screw the 6 feet into
the shallow mark holes
on the base using
screws .
M
3
G
G
M
M
M
M
M
M
Finished
front edge
3
Step 17
Fit the base
Attach the base to
the ends and the
upright using 9
screws and tighten
them using the allen key
. .
3
1
2
F
E
1
1
2
3
13
E
F
F
F
F
F
F
F
F
F
Unit colour on
the top surface
F
F
F
F
F
F
F
F
F
Assembly Instructions
14
Step 18
1
1
2
Fit the top
Attach the top to the
ends and the upright
. using 9 screws
and tighten them using
the allen key .
3
1
2
F
E
E
3
Finished
front edge
Finished
front edge
Assembly Instructions
Step 19
15
yy
y
x
x
D
b:
Fit the back panels
a: Square up the unit by
making sure that the
measurement x:x equals
y:y.
Place the small back
and large back ,
coloured surface facing
down, onto the unit as
shown.
Make sure that the 2
backs are pushed up
tight against each other
and that they meet in the
centre of the divider’s
back edge.
b: Nail around
the outside edges of
the 2 backs.
Note: Do not nail where
the 2 backs meet.
c: Push the nail screws
. through the back
holders and tap them
down between the small
back and large back
. and into the back
edge of the upright .
Keep tapping the nail
screws in until the
back holders dig into
the small and large back.
Stand the unit up for
the next step.
8
9
D
I
L
8
9
2
I
L
Warning: The
unit is heavy.
Lift with care.
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
LI
+
c:
8
9
I
L
8
9
L
Note: These can
also be round
Note: If ever you need to take
the backs off to dismantle the
unit, the nail screws can be
taken out using a screwdriver.
I
L
Assembly Instructions
16
Step 20
K
Fit the hanging rail(s)
If required, push the
hanging rail(s) and
into the rail holders
fitted to the panels.
6 7
K
7
6
Assembly Instructions
Step 21
17
L
NOTE
The unused fittings from this assembly are used to fit the doors.
Please refer to the instructions packed with the doors.
IMPORTANT
This unit MUST be fixed to a wall using both
of the overbalance protector kits supplied.
The unit must be level and square before
fitting the overbalance protector kits.
Fit both of the overbalance protector kits
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall by fitting of both of
the overbalance
protector kits to the
unit, or an alternative
fixing method of your
choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
P
P
P
WALL
Wall fixing
(not supplied)
Screw
(not supplied)
Washer
Strap
P
Strap
Washer
Screw
TOP OF UNIT
P
Assembly Instructions
18
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
Step 22
Chest
Loose
Shelf
Loose
Shelf
Loose
Shelf
Door
Fit the doors and, if
required, the shelf
pack and internal
chest
Please refer to the
instructions packed with
the doors, shelf pack or
internal chest.
Door
Door
IMPORTANT
The unused fittings from this assembly are used to fit the doors.
Please refer to the instructions packed with the doors.
ALR2956
MADE IN
BRITAIN
Dimensions
Width - 49.5cm
Depth - 1.5cm
Height - 210cm
Atlas - Single Mirror Door
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 08/01/14
Important - Please read these instructions fully before starting assembly
157/5709
IMPORTANT
Have you purchased a Single Robe
and an Internal 3 Drawer Chest?
The Chest must be placed into the
Robe BEFORE the Door is fitted.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This panel weighs
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Component - Panel
Please check you have the panel listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Mirror Door (D2398MA)
(2100 x 495mm)
These fittings are packed with the Single Mirror Door.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
O
Hinge (F328)
J
13mm Screw (F63)
These fittings are packed with the Robe Carcass.
The quantities will depend on which robe you have bought.
Mirror - SG23
2099 x 494mm
Safety Back SAR
Door Push (F258) x 1
Y
Door Plate (F259) x 1
13mm Screw (F52) x 2
X
Z
Assembly Instructions
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Do not drill the Mirror
Door?
90
J
J
O
J
J
O
J
J
O
J
J
O
Prepare the door(s)
Lay the door down onto
a soft, smooth surface.
Push fit 4 hinges into
each door.
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
J
O
IMPORTANT
DO NOT drill any holes in the Mirror Door.
If you have purchased a Standard Door
please use the instructions
packed with it.
Warning: The
door is heavy.
Lift with care.
Warning:
Glass! Handle
with care
Assembly Instructions
4
Step 3
Fit the door(s)
2 people are needed
here
Line up the 2 screws in
the top hinge with the
2 holes at the top of the
panel and push them in.
Working down the door,
push in the other hinges.
When all of the hinges
have been pushed into
place, tighten the 2
screws on each hinge.
Note: Fit the top hinge 1st
Choose where you would like your mirror door.
This shows a door being fitted onto the right side of a single robe.
The same assembly method applies to all doors and robes.
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
O O
Warning: The
door is heavy.
Lift with care.
O
Warning:
Glass! Handle
with care
Assembly Instructions
5
Step 4
Adjust the door if
needed
a: Before adjusting the
door, use a spirit level to
check the top (or base)
of the unit is level, frontto-back and side-to-side
in the 3 positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
b:
c:
d:
a:
A
A
B
C
Assembly Instructions
6
Step 5
Fit the Door Push
a: The arrows show the
Door Push fixing positions
on each of the Atlas
Robes.
These are pairs of holes
on the underside of the
Fixed Shelves.
Make sure you choose
the correct position so
that the Mirror Door
closes onto the Door
Push.
b: Fit a door plate for
each mirror door to the
fixed shelf using 2
screws .
Press the door push
into the door plate .
Press the back of the
door push to click
into place.
c: To open and close a
mirror door, press it
where the door push is
located.
You can adjust the door
push, in or out, by
turning it clockwise or
anti-clockwise to suit
your requirements.
X
X
Y
Y
Z
Z
Y
X
Z
Y
Z
a:
b:
c:
Adjustment
Z
These diagrams show the fixed shelves at the top end of the units.
You may have fitted them in the middle of the unit.
Assembly Instructions
7
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2960
Step 6
Important information
IMPORTANT INFORMATION ABOUT THIS PRODUCT
This product complies with the requirements of BS 7449:1991 and has been manufactured by
DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE,
THORNABY-ON-TEES, CLEVELAND, TS17 9LT
.
The product code for this unit and the item code(s) for the glass components are listed in the Assembly
Instructions along with a description of the type of glass used. All clear/tinted glass complies with the
requirements of BS 6206 Class A. All mirrors comply with the requirements of BS 6206 Class C. If the
glass component contained in this unit is chipped or broken consult the furniture manufacturer, retailer,
or agent with regard to obtaining a manufacturing specification and shape for replacement glass
quoting the unit description and batch number or date of manufacture.
Do not place very hot or very cold items against or in close proximity to glass surface(s) unless
adequately thick insulating material is used to prevent such items coming in contact with the glass.
Do not strike the glass with hard or pointed items.
Do not sit or stand upon horizontal glass surfaces.
When cleaning glass panels use a damp cloth or leather with washing up liquid or soft soap if
necessary - do not use washing powders or any other substance containing abrasives since these
substances scratch glass.
If stated in the instruction leaflet, it is essential that this unit is fixed to a wall.
KEEP THESE INSTRUCTIONS FOR FUTURE USE
MADE IN
BRITAIN
Dimensions
for each door
Width - 49.5cm
Depth - 1.5cm
Height - 210cm
Atlas - Standard Double Door
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 17/11/14
Important - Please read these instructions fully before starting assembly
151/7396
157/7240
157/2063
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: These panels weigh
approximately 22kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Component - Panel
Please check you have the panel listed below
2
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Standard Door (D2398A)
(2100 x 495mm) x 2
These fittings are packed with the Robe Carcass.
The quantities will depend on which robe you have bought.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
H
O
J N
19mm Screw (F461)
Handle (F328)
Hinge (F328)
13mm Screw (F63)
Assembly Instructions
3
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Step 2
Have you purchased a
Mirror Door?
90
J
J
O
J
J
O
J
J
O
J
J
O
Prepare the doors
Push fit 4 hinges into
each door.
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
J
O
IMPORTANT
If you have purchased a Mirror Door,
DO NOT follow these instructions.
Please use the instructions packed
with the Mirror Door.
Assembly Instructions
4
Step 3
For a door which has
a handle on the left,
drill these 2 handle
holes
Important: Please follow
these instructions
carefully.
Lay the door down onto
a smooth surface.
Check that the hinges
and holes are in the
same place as the
diagram.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
IMPORTANT
This step shows which handle holes to drill for doors
that have their handles on the LEFT, as shown below.
Go to Step 4 for how to drill a
door with its handle on the RIGHT.
ONLY drill these 2 holes
Small piece of
waste wood
Small piece of
waste wood
Assembly Instructions
5
Step 4
Small piece of
waste wood
Small piece of
waste wood
IMPORTANT
This step shows which handle holes to drill for doors
that have their handles on the RIGHT, as shown below.
Go to Step 3 for how to drill a
door with its handle on the LEFT.
For a door which has
a handle on the right,
drill these 2 handle
holes
Important: Please follow
these instructions
carefully.
Lay the door down onto
a smooth surface.
Check that the hinges
and holes are in the
same place as the
diagram.
Note: We recommend
the use of a small piece
of waste wood, placed
behind the holes while
drilling, to reduce the
possibility of any
breakout.
Using the pilot holes in
the rear face of the door,
drill through the 2 holes
indicated opposite, using
a 2.5mm diameter drill.
Turn the door over and
open out the 2.5mm
holes that you have just
drilled by drilling back
through them with a
5mm drill.
ONLY drill these 2 holes
Assembly Instructions
6
Step 5
Fit the doors and the
handles
2 people are needed
here
Make sure that the doors
are the correct way
around. The bottom hole
on the back surface of
the door will be one of
holes that you have
drilled.
Line up the 2 screws in
the top hinge with the
2 holes at the top of the
panel and push them in.
Working down the door,
push in the other hinges.
When all of the hinges
have been pushed into
place, tighten the 2
screws on each hinge.
Attach a handle to
each door using 2
screws .
This shows a door being fitted onto the right side of a double robe.
The same assembly method applies to all doors and robes.
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
O O
Warning: The
door is heavy.
Lift with care.
O
N
H
H
H
N
Note: Fit the top hinge 1st
Assembly Instructions
7
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
and quote the reference numbers on the component pages.
Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW
ALR2961
Step 6
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
b:
c:
d:
a:
A
A
B
C
Loading...