Arecont Vision AV1355DN-1HK, AV1355DN, AV2155-1HK, AV2155, AV2155DN-1HK Installation Manual

...
Page 1
Arecont Vision MegaDomeTM Installation Manual
0 | P a g e
Page 2
Arecont Vision MegaDomeTM Installation Manual
H G F E C
A
D B
MegaDome™ Installation Manual
Inside the box:
A. Arecont Vision MegaDomeTM B. Mounting template C. Magnetic core D. Pack of four (4) wood screws and four (4)
dry wall anchors E. One double sided hex key F. One single sided hex key G. Security L-key H. Power cable
Not included but needed:
#1 Phillips head screw driver  #2 Phillips head screw driver
Mounting the Camera:
1. Remove camera and hardware from the box.
2. Using the Mounting template, prepare the mounting provisions for camera installation. NOTE: the 19.5mm diameter
hole on the Mounting template is where the Ethernet cable will be exiting the MegaDomeTM, align accordingly. If using the side conduit hole, please see step 9 below.
3. Using Security L-key, loosen the four (4) screws securing the dome cover (Image
2). Remove vandal resistant dome cover. NOTE: Do not remove screws from the dome cover.
Image 2
Image 1
1 | P a g e
Page 3
Arecont Vision MegaDomeTM Installation Manual
HOLE
POWER
RJ-45
4. Run Ethernet cable through the hole on the bottom of the camera (Image 3) and plug it into the RJ45 port. NOTE: If the camera will
be powered via PoE, please skip to step 6.
5. If the camera is powered by an outside power supply, run the supplied power cable through the hole and connect it to its respective connector inside the camera (Image 3).
NOTE: Make sure that your installation of wires complies with Electrical Code of the local government where the camera is installed and no bare wires are exposed.
6. Align the holes in the camera with the prepared holes on the mounting surface. Attach the camera to the mounting surface with the wood screws or any optional hardware suitable for the mounting surface.
7. Install the included magnetic core onto the Ethernet cable as shown in Image 4. NOTE:
Ensure both tabs are tightly secured.
Image 3
Image 4
2 | P a g e
Page 4
Arecont Vision MegaDomeTM Installation Manual
(yaw)
TILT
PAN
8. Reference Image 5 for proper positioning of the magnetic core.
9. If you are using the side conduit opening, remove the conduit plug by first removing the socket set screw using one of provided Allen keys (Image 6).
Image 5
Adjusting the Tilt, Pan, Z-axis (yaw) and Focus:
10. To adjust the tilt, use a #1 Phillips screwdriver to loosen the screw on the side of the plastic lens bracket 1/4 turn (Image 7). CAUTION: Do not remove the screw!
11. Adjust lens tilt as required and tighten the screw from step 10.
12. To adjust the pan, use a #2 Phillips screwdriver to loosen the screw as shown in Image 7.
13. Adjust the pan as required and tighten the screw from step 2.
14. To adjust the Z-Axis, or Yaw, for vertical wall mounting, loosen the set screw as shown in
Image 7. NOTE: There are two set screws on opposite sides; both need to be loosened.
15. Adjust the Z-Axis as required and tighten the set screw back down.
Image 6
Z-AXIS
Image 7
3 | P a g e
Page 5
Arecont Vision MegaDomeTM Installation Manual
B
A
C
16. To adjust back focus, loosen the two (2) set screws with the appropriate Allen key as shown Image 8 (only one of two screw holes shown). Adjust the silver back focus ring as needed and tighten down the set screws.
17. To focus the lens, loosen the three set screws as shown in Image 9 and adjust each as needed. A adjusts the zoom, B adjusts the iris (adjustment is the band between A and C as outlined in red; there is no set screw), C adjusts the focus.
18. Remove the protective film from the camera dome. NOTE: be cautious not to scratch the vandal dome cover.
19. Secure the vandal dome cover to the camera.
BACK
FOCUS
SET
BACK
FOCUS
Image 8
Image 9
4 | P a g e
Page 6
Arecont Vision MegaDomeTM Installation Manual
E
C
H G D
B A
I F
MegaDome™ Pendant Installation Instructions
Inside the box:
A. Top shield B. Pendant Mount C. Mounting template D. Pack of four (4) machine screws E. Pack of four (4) small machine screws F. Pack of four (4) wood screws and four (4)
dry wall anchors G. Large round rubber gasket H. Smaller square rubber gasket I. One double sided hex key
Not included but needed:
J. #2 Phillips head screw driver
21. Using the Mounting template, prepare the
22. Place small gasket onto pendant dome as
23. Attach Dome to Pendant as shown in Image
24. Install large round rubber gasket onto
Image 11 Image 12
mounting provisions for camera installation.
shown in image 11.
12 using four machine screws provided.
Pendant as shown in image 12. Be sure to align the holes appropriately.
25. Run Ethernet Cable and outside power cable (if necessary) through the Pendant.
26. Attach Pendant to the ceiling using the four wood screws provided or any optional
Image 10
20. Remove Pendant Mount and hardware from the box.
hardware suitable for the mounting surface.
27. For installation of the camera, please reference “Mounting the Camera”.
5 | P a g e
Page 7
Arecont Vision MegaDomeTM Installation Manual
E B D C A
MegaDome™ Wall Mount Installation Instructions
Inside the box:
A. Top shield and Wall mount B. Mounting template C. Pack of four (4) machine screws D. Pack of four (4) wood screws and four (4)
dry wall anchors
E. Large round rubber gasket
Not included but needed:
#2 Phillips head screw driver
Image 14
29. Using the Mounting template, prepare the mounting surface.
30. Install large round rubber gasket onto Wall Mount as shown in image 14. Be sure to align the holes appropriately. NOTE: the four
little rubber nipples protrude into the top shield.
31. Run Ethernet Cable and outside power cable (if necessary) through the Wall Mount.
Image 13
28. Remove Wall Mount and hardware from the box.
32. Attach Wall Mount to the wall using drywall screws or any optional hardware suitable for the mounting surface.
33. For installation of the camera, please reference “Mounting the Camera”.
6 | P a g e
Page 8
Arecont Vision MegaDomeTM Installation Manual
B
C
A D E
MegaDome™ Junction Box Adapter Installation Instructions
Inside the box:
A. Junction Box Adapter B. Pack of four (4) machine screws C. Pack of four (4) wood screws and four (4)
dry wall anchors D. Large round rubber gasket E. One double sided hex key
Not included but needed:
#2 Phillips head screw driver  MegaDome™ Wall Mount, MD-WMT  ¾” NPT Conduit (if necessary)
Image 15
34. Remove Junction Box and hardware from the box
Image 16 Image 17
35. Remove the conduit plug by first removing the socket set screw using one of provided Allen keys shown in Image 16.
36. Attach Junction Box Adapter to the wall using drywall screws or any optional hardware suitable for the mounting surface.
37. Attach MegaDome™ Wall Mount to Junction Box Adapter as shown in Image 17.
38. Connect ¾” NPT Conduit to Junction Box Adapter
39. Run Ethernet Cable and outside power cable (if necessary) through the Junction Box Adapter and Wall Mount.
40. For installation of the camera, please reference “Mounting the Camera”.
7 | P a g e
Page 9
Arecont Vision MegaDomeTM Installation Manual
B
C
A
D
Support
MegaDome™ Flush Mount Adapter Installation Instructions
Inside the box:
F. Flush Mount Adapter G. White Trim Ring H. Pack of four (4) machine screws and one
(1) I-Blot
I. Mounting template
Not included but needed:
#2 Phillips head screw driver
Image 18
41. Remove Flush Mount Adapter, Trim Ring and hardware from the box
45. Screw the “lever screws” until the FMA is snuggly installed, as shown in Image 19. The “Support Arm” will ride down the screw to compress the mounting surface. NOTE: Do
not over-torque the lever screws
46. Attach the Trim Ring to the Flush Mount Adapter by rotating clockwise as show in
Image 20.
Arm
Lever
screw
Image 19
42. Attach Dome to Flush Mount Adapter as shown in Image 19. Please reference Mounting the Camera”, if needed.
43. Using the Mounting template, cut a hole in surface for mounting.
44. Insert Flush Mount Adapter into the hole.
Image 20
8 | P a g e
Page 10
Arecont Vision MegaDomeTM Installation Manual
B
A
MegaDome™ Electrical Box Adapter Installation Instructions
Inside the box:
A. Electrical Box Adapter B. Pack of four (4) machine screws
Not included but needed:
#2 Phillips head screw driver  Common Electrical Box, such as single
gang box, double gang box or square electrical box.
Image 22
Image 21
47. Remove Electrical Box Adapter and hardware from the box.
48. Attach Electrical Box Adapter to Electrical Box as shown in Image 22.
49. Attach Dome to Electrical Box Adapter as shown in Image 23. Please reference Mounting the Camera”, if needed.
Image 23
9 | P a g e
Page 11
Arecont Vision MegaDomeTM Installation Manual
A B C
D
E
Wall
Adapter
Compression
Screws
MegaDome™ Pole Mount Adapter Installation Instructions
Inside the box:
A. Pole Mount Adapter B. 2x Compress Fittings C. 2x Small Steel Straps D. 2x Large Steel Straps E. Pack of four (4) machine screws
Not included but needed:
#2 Phillips head screw driver  MegaDome™ Wall Mount Adapter
53. Run Ethernet Cable and outside power cable (if
54. Use the supplied two Steel Straps to attach the
55. Attach Dome to Wall Mount Adapter. Please
56. Tighten the Compress Fittings to seal the
necessary) through the Compress Fittings and MegaDome™ Wall Mount.
Pole Mount Adapter to the pole and tighten the compression screws as shown in Image
25.
reference “Mounting the Camera”, if needed.
wiring holes.
50. Remove Pole Mount Adapter, Compress
51. Install Compress Fittings to Pole Mount
52. Attach MegaDome™ Wall Mount Adapter to
Image 24
Fittings, Steel Straps and hardware from the box.
Adapter as shown in Image 25.
Pole Mount Adapter as shown in Image 26.
Image 25
Mount
Image 26
10 | P a g e
Page 12
Arecont Vision MegaDomeTM Installation Manual
A
B C D
MegaDome™ Corner Mount Adapter Installation Instructions
Inside the box:
A. Corner Mount Adapter B. 2x Compression Fittings C. Pack of four (4) machine screws D. 2x Packs of four (4) wood screws and four
(4) dry wall anchors
Not included but needed:
#2 Phillips head screw driver  MegaDome™ Wall Mount Adapter
Image 28
Image 29
60. Run Ethernet Cable and outside power cable (if necessary) through the Compress Fittings
Image 27
57. Remove Corner Mount Adapter, Compress Fitting and hardware from the box.
58. Install Compress Fittings to Corner Mount Adapter as shown in Image 28.
59. Attach Wall Mount Adapter to Corner Mount Adapter as shown in Image 29.
and MegaDome™ Wall Mount.
61. Using the screws provided (or other hardware) attach the Corner Mount Adapter to an exterior 90° corner wall.
62. Attach Dome to Wall Mount Adapter. Please reference “Mounting the Camera”, if needed.
63. Tighten the Compress Fittings to seal the wiring holes.
11 | P a g e
Page 13
Arecont Vision MegaDomeTM Installation Manual
A
MegaDome™ I/O Cable Connection
Inside the box:
A. I/O Cable
Not included but needed:
Flat head screw driver
Image 30
64. To use the I/O ports of the MegaDome, locate the “J7” connector. NOTE: There are two
connectors that look identical, be sure to use the one adjacent to the capacitor labeled “1000 jFK.8L9” shown in Image 31.1 and NOT the one adjacent to the hole in the back of the camera as shown in Image 31.2.
65. Run the I/O cable through the hole in the bottom of the camera and plug it into the “J7”
connector as shown in image 31. NOTE: The
connection is a little stiff so be sure to apply enough pressure to connect it; using a flat head screw driver to push it in is recommended.
Electrical Characteristics: Min Max
Input voltage (V) ON 2.9 6.3 (measured between + and – terminals)
Output current (mA) (measured between + and – terminals) Applied Voltage Rage: 0 - 80V
NOTE: Both the input and the output are electrically
isolated from the rest of the camera’s electrical circuitry via general-purpose photo couplers. The input is additionally protected with a serial 250 Ohm resistor, and a debouncing circuit. Duration of any input signal should be at least 5 ms to comply with the requirements of the debouncing circuit.
Orange OUT + Yellow OUT – White IN + Black IN -
Table 1
Table 2
OFF 0 1.3
ON - 50
OFF - 0.1
12 | P a g e
Page 14
Arecont Vision MegaDomeTM Installation Manual
Image 31
Image 31.1 Image 31.2 Connect Here Do NOT Connect Here
13 | P a g e
Page 15
Arecont Vision MegaDomeTM Installation Manual
B A
MegaDome™ Heater Accessory
Inside the box:
A. Heater B. Two (2) screws
Not included but needed:
#1 Phillips head screw driver
Image 32
61. Screw the heater board to the standoffs as shown in Image 34
Image 33
66. Run the heater cable out of the hole in the bottom of the camera and connect it to 10­50VDC power supply. 10 Watts max. Red is positive (+) cable.
67. Remove the heater kit from the box.
68. With the heater element protruding out of the camera, align the two (2) holes on the heater board with the two standoffs shown in Image
33.
Image 34
14 | P a g e
Page 16
Arecont Vision MegaDomeTM Installation Manual
A
MegaDome™ Focus Tool Accessory
Inside the box:
A. Focus Tool
NOTE: Focus Tool is a small piece of bubble which has same material and property as bubble’s, including thickness, curvature and other optical performance.
Image 35
69. Attach Focus Tool on the top of lens shown
in Image 36.
70. Adjust the lens focus until getting clear image shown image 37.
Image 36
71. Fix the screws on the lens
72. Remove Focus Tool from lens
73. Put bubble and secure it on MegaDome
NOTE: Focusing Tool is used to compensate the focus shift after putting bubble on camera.
Image 37
15 | P a g e
Page 17
Arecont Vision MegaDomeTM Installation Manual
16 | P a g e
Loading...