Aquatic AV AQ-IP-3B User Manual
INSTRUCTION MANUAL
AQ-IP-3B
iPod Digital Media Center
AM/FM/XMRadio
AQ-IP-3B
SATINFO
READY
INT
READY
TOP
MULTIENVIRONMENT
PLAYER
1. MOUNTING PRECAUTIONS
The AQ-IP-3B is designed for a multi environment application. For easy system set-up,
mount the Media Center so the front panel controls will be easily accessible. In addition,
observe the following precautions: 1. Check clearances on both sides of a planned
installation before drilling any holes or installing any screws. 2. When routing RCA cables,
keep them away from power cables and output speaker wires. 3. Due to the design for a
multi environment application, support the back of the unit with the supplied backalways
strap.
1. Slide mounting can into DIN opening
E-1
2. Slide backing brackets into position and tighten center bolts. Remove backing brackets
handles by bending backing bracket handles until they break off.
3. Slide Media Center into mounting bracket. Secure Media Center using supplied SS
hardware and back strap.
E-2
2. WIRING DIAGRAM
321
654
987
12 11 10
VIEW B-B
WIRE INSERTION VIEW
FUSE
B
1A
RED
XM
MINI TUNER
XM
PIN NO.
1 RED
GREEN/BLACK
2
GREEN
3
YELLOW
4
5
WHITE/BLACK
6
WHITE
7
BLUE
GRAY/BLACK
8
9
GRAY
10
BLACK GROUND
VIOLET/BLACK
11
VIOLET
12
B
BLACK
TO XM
REMOTE
RF
REMOTE
WIRE COLOR
YELLOE
FUSE
15A
TO RF
BLACK
DESCRIPTION
ACCESSORY (+12V)
LEFT REAR SPEAKER (-)
LEFT REAR SPEAKER (+)
BATTERY (+12V)
LEFT FRONT SPEAKER (-)
LEFT FRONT SPEAKER (+)
POWER ANTENNA
RIGHT FRONT SPEAKER (-)
RIGHT FRONT SPEAKER (+)
RIGHT REAR SPEAKER (-)
RIGHT REAR SPEAKER (+)
+12V CABLE
(350mA)
(350mA)
DC12V_1
DC12V_2
RED 20#
LINE OUT
RIGHT
LINE OUT
RED
L-CH
RED
LEFT
RIGHT
LINE OUT
LINE OUT
WHITE
R-CHR-CH L-CH
REAR LINE OUT FRONT LINE OUT
ANTENNA JACK
E-3
RED 20#
LEFT
WHITE
AUDIO IN(1) R
R-CH
SUB-W OUT
SUB-W OUT
AUDIO IN(1) L
AUDIO IN R
AUDIO IN L
L-CH
3. iPod OPERATION
INSTALLING iPod INTO THE BUILT-IN iPod DOCKING STATION
Always follow the below steps to install the iPod into the docking station.
Incorrect or improper installation may cause permanent damage to the
docking or the iPod unit.station
Step 1
Press down the button as indicated
below to unlock the iPod docking.
Step 2
Pull out the iPod mechanism.
as shown below.
Step 3
Press on this button on the left as
indicated below to unlock the
iPod mechanism.
Press down
Pull out
Never pull out this stick unless
docking is completely release out.
Step 5
(A).Once the stick is
completely pulled out,
user should see the
iPod connector,
(B). user can
connect
the iPod
to the
connector
as shown in this step.
Step 6
Step 7
Press the iPod on bothmechanism.
sides to hold the iPod firmly in place.
ress towards the iPod unit to hold the
P
iPod unit firmly in place
Push the stick & the connected iPod
inwards until it stops.
(B)
Plug connector into
bottom of iPod
(A)
Step 4
Press down this button
Pull out the iPod connector
as indicated below.
Pull out this stick
Step 8
E-4
Push inwards
Push the iPod inwards into
dock
the unit’s cabinet until it stops.
Push the docking back
into the cabinet
REMOVE iPod FROM THE BUILT-IN iPod DOCKING STATION
To take out the iPod from the docking station, user can first detach the front
panel, and repeat step 1 to step 8 to take out the iPod & return the iPod
docking inside the unit’s cabinet.
Step 1
Press the button as indicated below
to unlock the iPod docking.
Press down
Step 5
Once the connected iPod is completely out,
push on the locking buttons on
both sides of the
iPod connector
to release the
iPod as indicated
in the picture,
and remove the iPod unit.
Press toward this
lock switch
Step 2
Step 3
iPod holder.
Press down this button
Step 4
Pull out the iPod docking
as shown below.
Pull out
Never pull out this stick unless
docking is completely out.released
Press button on the left asthe
indicated below to unlock the
Pull out the iPod as indicated
below by pulling out the stick.
Step 6
Once the iPod unit is remove,
push the stick backward
into the iPod docking
station until it stops.
Step 7
Push on the iPod holders on both
sides until they stop.
Press towards the iPod unit to hold the
iPod unit firmly in place
Step 8
Push the iPod docking inwards into
the unit’s cabinet until it stops.
Push inwards
Pull out this stick
E-5
Push the docking back
to cabinet
iPod FULL CONTROL / OPERATION
This unit is equipped with iPod Ready function which end user to have direct control of the
iPod on thefront panelcontrol buttonand display iPod song information on the unit's LCD display.
Please read belowfor more detailsoperation
Turning iPod Power On and Off
The iPod power turns on automatically as soon as it is connected to the 30 Pin Connector and as
long as the unit gets power
. The iPod power can be turned OFF by removing the iPod from the 30
Pin Connector or if the vehicle's ignition is turned OFF. Under this condition the iPod will go into
pause mode andgoes into sleepmode about 2 minutes later
While the iPod is connected,the power cannotbe turned on oroff from theiPoditself.
Tips
“ ”to disconnect willbe shown in theiPod's display while itis connected tothe unit .
OK to disconnect
iPod Battery Charging
While connected to the unit, the iPod will automatically start re-charging as long as the vehicle's
ignition key isturn to ACCor ON.
Switch to iPod Mode
When the Head unit is on and iPod is connected to the 30 pin connector, press
powered
the mode button to change to iPod mode and the unit will display for a while
then starts the music files contained in the iPod and the playback will
automatically start. Press Mode button repeatedly to change to other modes or switch back to
iPod information Display on the Head Unit LCD
This unit can display the Song, Artist, Album name and Elapsed time on the LCD display, these
information can be displayed by pressing the AS/PS button repeatedly while a iPod Song file is
playing
Searching a Desire Song
Under iPod playback mode, press BAND to enterinto the iPod Searching Mode. BAND
button repeatedly to the different searching methods asbelow :
1)
Play list
2)
Artist
3)
Album
4)
Song
5)
Genre
access
allows
Press the
E-6
Loading...