American Power Conversion Smart UPS SUA3000XL, Smart UPS 230 Vac, Smart UPS 120 Vac, Smart UPS 3000 VA XL, Smart UPS 208 VAC User Manual

User Manual English

APC Smart-UPS® XL

2200/3000 VA XL

120/208/230 VAC

Tower/Rack-Mount 5U

Uninterruptible Power Supply

990-2975 09/2006

Introduction

About this UPS

The American Power Conversion (APC®) Uninterruptible Power Supply (UPS) provides protection for
electronic equipment from utility power blackouts, brownouts, sags and surges. The UPS filters small utility
line fluctuations and isolates electronic equipment from large disturbances by internally disconnecting from
utility line power. The UPS provides continuous power from the internal battery until utility power returns to
safe levels or the battery is fully discharged.

Unpack

Read the Safety Guide before installing the UPS.

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents:

•UPS

•Front bezel

•Literature kit containing:
– EPO connector
– Serial cable
– USB cable
– Eight ornamental screws for

securing the unit in the rack

– Eight 5/16 in (.8 cm) pan-head

screws for attaching cleats to the
chassis rails
(required for four post rack only)

– Eight 5/8 in (1.6 cm) pan-head

screws for attaching rack-mount
brackets to the unit

– Eight snap-on speed nuts
– Two rail cleats (required for four post

rack only)
– Two rack-mount brackets
– Product documentation
– Smart-UPS® User Manuals CD
– PowerChute® Business Edition CD
– Safety information
– Warranty information

Additional contents for
230 V models:

– APC power cable
– Alternate input power cord

(UK customers)
–IEC Power cord
– IEC jumper cables

Specifications

Temperature

Operating
Storage

32° to 104° F (0° to 40° C)
5

° to 86° F (-15° to 30° C) charge the UPS battery every six months

86

° to 113° F (30° to 45° C) charge the UPS battery every three months

Maximum
Elevation

Operating
Storage

Humidity

Wei ght

Maximum Number of External Battery Packs Supported by the
Smart-UPS XL

10,000 ft (3,000 m)
50,000 ft (15,240 m)

0 to 95% relative humidity, non-condensing

142 lbs (64 kg) with battery module
89 lbs (40 kg) without battery module
27 lbs (12 kg) each battery module

NOTE: The model and serial numbers are located on a small, rear panel label. For some models, an additional label
is located on the chassis under the front bezel.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 3

This unit is intended for indoor use
only. Select a location sturdy enough
to handle the weight.

Do not operate the UPS where there
is excessive dust or the temperature
or humidity are outside the specified
limits.

Environmental factors impact battery
life. High temperatures, poor utility
power, and frequent, short duration
discharges will shorten battery life.

142 lbs (64 kg)

10

Installation

The UPS is shipped in tower configuration.

Tower Configuration

Connect the battery.

After the battery has been connected, tuck the battery cables in between the battery and the
battery door. This will ensure a secure fit of the bezel to the unit.

4 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Rack-Mount Configuration

This unit is intended for mounting in a two post rack. To order a four post rack-mount kit contact your dealer or
refer to the APC Web site, www.apc.com.

Tower to rack-mount conversion procedure

The UPS and the battery modules are heavy. Remove the battery modules to lighten the UPS during
installation.

Pull the battery disconnect
strap attached to the battery
connector. DO NOT pull
the battery cables to
disconnect the battery.

Battery
Disconnect
Strap

Remove the top cover and .
Remove and rotate the display

panel .

Foam
Spacer

Disconnect
Battery

Four post rack-mount
bracket position

Two post rack-mount
bracket position

x4

5/8 in

1.6 cm

A four post rack configuration requires installation
of two brackets in the forward position (see diagram
above), two cleats (supplied with this unit), and the
four post rails. The rails can be ordered through the
APC Web site www.apc.com.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 5

Install unit in rack

Ensure rack stability prior to installing devices in the rack.

The UPS should be installed at or near the bottom of the rack. If external battery packs are to be installed in the
rack, the UPS must be the top unit in the configuration.

Connect
Battery

x4
Ornamental

Foam Spacer

After all of the batteries have been connected, tuck the battery
cables in between the batteries and the battery doors. This will
ensure a secure fit of the bezel to the unit.

Accessories

This UPS is equipped with an accessory SmartSlot. Refer to the APC Web site, www.apc.com for available
accessories.

If a standard accessory, such as a Network Management card is to be installed on this UPS, refer to the Utility
CD for user documentation.

Install accessories prior to connecting power to the UPS.

6 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Start-Up

Connect Equipment and Power to the UPS

1. The UPS features a transient voltage surge-suppression (TVSS) screw located on the rear panel, for
connecting the ground lead on surge suppression devices such as telephone and network line protectors.

Prior to connecting the grounding cable, ensure that the UPS is NOT connected to utility or battery
power.

2. Connect equipment to the UPS.
NOTE: This UPS is equipped with an external battery connector on the rear panel of the unit.

Where appropriate use an APC extension battery cable. For ordering details contact your dealer or APC
through the Web site www.apc.com.

3. Add optional accessories to the SmartSlot located on the rear panel.

4. Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.

– 230 V models: The utility power cord is supplied in the UPS literature kit. Prior to connecting the

utility power, connect the ground lead (optional) to the TVSS screw.

5. 120 V models: Check the SITE WIRING FAULT LED located on the rear panel. The LED will be
illuminated if the UPS is plugged into an improperly wired utility power outlet, (see Troubleshooting).

6. To use the UPS as a master on/off switch be sure all connected equipment is switched on.

Rear Panels

3000 VA

120 VAC

2200 VA

120 VAC

3000 VA

208 VAC

2200 VA
3000 VA

230 VAC

Start the UPS

1. Press the button on the front panel to start the UPS.

– The battery charges to 90% capacity during the first four hours of normal operation. Do not

expect full battery run capability during this initial charge period.

– Refer to the APC Web site, www.apc.com for battery runtimes.

2. For optimal computer system security, install PowerChute Smart-UPS monitoring software.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 7

Communication Ports

SERIAL PORT

USB PORT

Use only the supplied cable to connect to the serial port. A standard
serial interface cable is incompatible with the UPS.

Serial and USB ports cannot be used simultaneously.

Emergency Power Off

The emergency power off (EPO) feature is user configurable. EPO provides immediate de-energizing of
connected equipment from a remote location, without switching to battery operation.

1. Use the EPO connector supplied with the UPS.

2. Use a normally-open contact to connect the +24 terminal to the IN terminal. External voltage is not
required.

3. Wire the four-pin connector to the EPO system.

EPO PORT

(located on rear panel)

The EPO interface is a Safety Extra Low Voltage (SELV) circuit. Connect it only to other SELV circuits.
The EPO interface monitors circuits that have no determined voltage potential. Such closure circuits
may be provided by a switch or relay properly isolated from the utility. To avoid damage to the UPS, do
not connect the EPO interface to any circuit other than a closure type circuit.

Use one of the following cable types to connect the UPS to the EPO switch.

• CL2: Class 2 cable for general use.

• CL2P: Plenum cable for use in ducts, plenums, and other spaces used for environmental air.

• CL2R: Riser cable for use in a vertical run in a floor-to-floor shaft.

• CLEX: Limited use cable for use in dwellings and for use in raceways.

• For installation in Canada: Use only CSA certified, type ELC, (extra-low voltage control cable).

• For installation in other countries: Use standard low-voltage cable in accordance with national and
local regulations.

EPO

Connector

8 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Operation

Display Panels

120/208 V models

120/208 V

Battery
Charge

230 V models

Display Panel Indicators and Function Buttons

Indicator

LED

Indicator Title Description

230 V

On Line The UPS is supplying utility power to the connected equipment,

(see Troubleshooting).

AVR Trim The UPS is compensating for a high utility voltage. Refer to the APC Web site,

AVR Boost The UPS is compensating for a low utility voltage. Refer to the APC Web site,

On Battery The UPS is supplying battery power to the connected equipment.

Overload The connected equipment is drawing more than the UPS power rating allows,

Replace Battery/Battery
Disconnected

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 9

www.apc.com for AVR settings.

www.apc.com for AVR settings.

(see Troubleshooting).

The battery is disconnected or must be replaced, (see Troubleshooting).

Indicator

LED

Indicator Title Description

120 V

Battery
Charge

Feature

Button

230 V

208 V

Diagnostic
Utility Voltage

The UPS has a diagnostic feature that indicates the utility voltage.

The UPS starts a self-test as part of this procedure. The self-test does not affect
the voltage display.

Press and hold the button to view the utility voltage bar graph indicator.

Battery
Charge

After a few seconds, this five-LED Battery Charge indicator on the right of
the display panel will show the utility input voltage.

Refer to the figure on the left for the voltage reading.
Values are not listed on the UPS.

The indicator on the UPS shows the voltage is between the displayed value on
the list and the next higher value, (see Troubleshooting).

Feature Title Function

Power On Press this button to turn on the UPS. Continue reading for additional

capabilities.

Self-Test Automatic: The UPS performs a self-test automatically when tuned on, and

every two weeks thereafter (by default). During the self-test, the UPS
briefly operates the connected equipment on battery.

Manual: Press and hold the

button for a few seconds to initiate the

self-test.

Cold Start When there is no utility power and the UPS is off, the cold start feature will

switch the UPS and connected equipment onto battery power,
(see Troubleshooting).

Power Off Press this button to turn off the UPS.

10 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Configuration

UPS settings

Settings are adjusted through PowerChute software or optional SmartSlot accessory cards.

Factory

Function

Automatic
Self-Test

UPS ID UPS_IDEN Up to eight characters

Date of Last
Battery
Replacement

Minimum Capacity
Before Return from
Shutdown

Voltage Sensitivity

The UPS detects
and reacts to line
voltage distortions
by transferring to
battery operation to
protect the
connected
equipment.

Default

On startup and
every 14 days
(336 hours)
there after

Manufacture
Date

0 percent • 0%

High sensitivity Brightly

User Selectable

Choices Description

• On startup and every
7 days (168 hours)
there after

• On startup and every
14 days (336 hours)
there after

• On startup only

• No self-test

(alphanumeric)

mm/dd/yy Reset this date when you replace the battery

• 60%

• 15%

• 30%

• 45%

illuminated: high
sensitivity

Dimly illuminated:
medium sensitivity

No illumination:
low sensitivity

• 75%

• 90%

Set the interval at which the UPS will execute a
self-test.

Uniquely identify the UPS, (i.e. server name or
location) for network management purposes.

module.

Specify the percentage to which batteries will
be charged following a low battery shutdown
before powering connected equipment.

Adjust by pressing the VOLTAGE SENSITIVIY
switch (rear panel). Use a pointed object, (such
as a pen) to do so.

Note: In situations of poor power quality, the
UPS may frequently transfer to battery
operation. If the connected equipment can
operate normally under such conditions, reduce
the sensitivity setting to conserve battery
capacity and service life.

Alarm Delay
Control

Shutdown Delay 90 seconds • 0 s

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 11

Enable • Enable

• Mute

• Disable

• 90 s

• 180 s

• 270 s

• 360 s

• 450 s

• 540 s

• 630 s

Mute ongoing alarms or disable all alarms.

Set the interval between the time when the UPS
receives a shutdown command and actual
shutdown.

Function

Factory

Default

User Selectable

Choices Description

Low Battery
Warning

PowerChute
software interface
provides automatic,
unattended
shutdown when
approximately two
minutes of battery
operated run time
remains.

Synchronized
Turn-on Delay

High Transfer Point 208 V models:

2 minutes

LED is located
on rear panel

0 seconds • 0 s

225 VAC

120 V models:
127 VAC

230 V models:

253 VAC

Brightly
illuminated:

low battery warning
level of about 2 minutes

Dimly illuminated:

low battery
warning level of about
5 minutes

No illumination:

low battery warning
level is about 8 minutes

• 240 s

• 60 s

• 120 s

• 180 s

• 225 VAC

• 229 VAC

• 127 VAC

• 130 VAC

• 253 VAC

• 257 VAC

• 300 s

• 360 s

• 420 s

• 233 VAC

• 237 VAC

• 133 VAC

• 136 VAC

• 261 VAC

• 265 VAC

The low-battery warning beeps are continuous
when two minutes of run time remain.

To change the default interval setting, use a
pointed object such as a pen to press the
VOLTAGE SENSITIVIY switch (rear panel),
while

pressing the button, (front display).

Change the low battery warning interval setting
to the time that the operating system or system
software requires to safely shut down.

Specify the time the UPS will wait after the
return of utility power before start up, (to avoid
branch circuit overload).

To avoid unnecessary use of the battery where
utility voltage is chronically high, set the high
transfer point higher if the connected
equipment can tolerate this condition.

Low Transfer Point 120 V models:

106 VAC

208 V models:

182 VAC

230 V models:

208 VAC

Output Voltage

230 V models 230 VAC

12 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

• 97 VAC

• 100 VAC

• 182 VAC

• 178 VAC

• 196 VAC

• 200 VAC

• 220 VAC

• 230 VAC

• 103 VAC

• 106 VAC

• 174 VAC

• 170 VAC

• 204 VAC

• 208 VAC

• 240 VAC

To avoid unnecessary use of the battery where
utility voltage is chronically low, set the low
transfer point lower if the connected equipment
can tolerate this condition.

Set the output voltage of the UPS.

Troubleshooting

Use this chart to solve minor UPS installation and operation problems. Refer to www.apc.com for assistance
with complex UPS problems.

Problem and/or Possible Cause Solution

UPS will not turn on

The battery is not connected properly. Check that the battery connector is fully engaged.

button not pushed.

The UPS is not connected to utility
power supply.

Very low or no utility voltage Check the utility power supply to the UPS by plugging in a table lamp. If the

UPS will not turn off

The UPS is experiencing an internal
fault

UPS beeps occasionally

Normal UPS operation when running
on battery.

UPS is not providing expected backup time

The UPS battery(s) are weak due to a
recent power outage or battery(s) are
near the end of their service life.

All LEDs are illuminated and the UPS emits a constant beeping

The UPS is experiencing an internal
fault.

Press the

Check that the power cable from the UPS to the utility power supply is
securely connected at both ends.

light is very dim, have the utility voltage checked.

Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.

None: The UPS is protecting the connected equipment. Press the button
to silence this alarm.

Charge the battery(s). Batteries require recharging after extended outages.
Batteries can wear faster when put into service often or when operated at
elevated temperatures. If the battery(s) are near the end of their service life,
consider replacing the battery(s) even if the replace battery LED is not yet
illuminated.

Do not attempt to use the UPS. Unplug the UPS and have it serviced
immediately.

button once to power-up the UPS and connected equipment.

Front panel LEDs flash sequentially

The UPS has been shut down remotely
through software or an optional
accessory card.

All LEDs are off and the UPS is plugged into a wall outlet

The UPS is shut down or the battery is
discharged from an extended outage.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 13

None: The UPS will restart automatically when utility power returns.

None: The UPS will restart automatically when utility power is restored and
the battery has a sufficient charge.

Problem and/or Possible Cause Solution

The Overload LED is illuminated and the UPS emits a sustained alarm tone

The UPS is overloaded. The connected equipment exceeds the specified “maximum load” as defined

in Specifications on the APC Web site, www.apc.com.

The alarm remains on until the overload is removed. Disconnect nonessential
equipment from the UPS to eliminate the overload condition.

The UPS continues to supply power as long as it is online and the circuit
breaker does not trip; the UPS will not provide power from batteries in the
event of a utility voltage interruption.

The Replace Battery/Battery Disconnected LED is illuminated

The Replace Battery/Battery

Check that the battery connectors are fully engaged.
Disconnected LED flashes and a short
beep is emitted every two seconds to
indicate the battery is disconnected.

Weak battery Allow the battery to recharge for 24 hours and perform a self-test. If the

problem persists after recharging, replace the battery.

Failure of a battery self-test: Replace
Battery/Battery Disconnected LED
illuminates and the UPS emits short
beeps for one minute. The UPS repeats
the alarm every five hours.

Allow the battery to recharge for 24 hours. Perform the self-test procedure to

confirm the replace battery condition. The alarm stops and the LED clears if

the battery passes the self-test.

If the battery fails again, it must be replaced. The connected equipment is

unaffected.

The Site Wiring Fault LED on the rear panel is illuminated (120 V model only)

The UPS is plugged into an improperly
wired utility power outlet.

Wiring faults detected include missing ground, hot-neutral polarity reversal,

and overloaded neutral circuit.

Contact a qualified electrician to correct the building wiring.

The input circuit breaker trips

The connected equipment exceeds the
specified “maximum load” as defined
in Specifications on the APC Web site,

Unplug all nonessential equipment from the UPS.

Reset the circuit breaker.

www.apc.com.

The AVR Boost or AVR Trim LEDs are illuminated

The system is experiencing very high or
low utility voltage.

Have a qualified service personnel check your facility for electrical

problems. If the problem persists, contact the utility company for further

assistance.

14 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Problem and/or Possible Cause Solution

There is no utility power

There is no utility power and the UPS is
off.

UPS operates on battery although line voltage exists

The UPS input circuit breaker trips. Unplug all nonessential equipment from the UPS.

Your system is experiencing very high,
low or distorted line voltage.

Battery Charge and Load LEDs flash simultaneously

The UPS has shut down.

The internal temperature of the UPS has
exceeded the allowable threshold for
safe operation.

Diagnostic utility voltage

All five LEDs are illuminated. The line voltage is extremely high and should be checked by an electrician.

There is no LED illumination. The line voltage is extremely low and should be checked by an electrician.

Use the cold start feature to supply power to the connected equipment front

the UPS battery(s).

Press and hold the

longer beep. Release the button during the second beep.

Reset the circuit breaker.

Move the UPS to a different outlet on a different circuit: Inexpensive fuel

powered generators may distort the voltage. Test the input voltage with the

utility voltage display, (see Operation). If acceptable to the connected

equipment, reduce the UPS sensitivity.

Check that the room temperature is within the specified limits for operation.

Check that the UPS is properly installed, allowing for adequate ventilation.

Allow the UPS to cool down. Restart the UPS. If the problem persists,

contact APC at www.apc.com.

button. There will be a short beep followed by a

On Line LED

There is no LED illumination. The UPS is running on battery, or it must be turned on.

The LED is blinking. The UPS is running an internal self-test.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 15

Maintenance, Transport, and Service

Replacing the Battery Module

This UPS has easy-to-replace, hot-swappable battery modules. Replacement is a safe procedure, isolated from
electrical hazards. You may leave the UPS and connected equipment on during the replacement procedure.

Once the batteries are disconnected the connected equipment is not protected from power outages.

Refer to the appropriate replacement battery user manual for battery module installation instructions. See your
dealer or contact APC at www.apc.com for information on replacement battery modules.

Be sure to deliver the spent battery(s) to a recycling facility or ship it to APC in the
replacement battery packing material.

Service

If the UPS requires service do not return it to the dealer. Follow these steps:

1. Review the problems discussed in Troubleshooting to eliminate common problems.

2. If the problem persists, contact APC Customer Support through the
APC Web site, www.apc.com.

– Note the model number of the UPS, the serial number located on the back of the unit, and the date

purchased. If you call APC Customer Support, a technician will ask you to describe the problem
and attempt to solve it over the phone. If this is not possible, the technician will issue a Returned

Material Authorization Number (RMA#).
– If the UPS is under warranty, repairs are free.
– Procedures for servicing or returning products may vary internationally. Refer to the APC Web

site for country specific instructions.

3. Pack the UPS in its original packaging. If this is not available, refer to www.apc.com for information
about obtaining a new set.

– Pack the UPS properly to avoid damage in transit. Never use Styrofoam beads for packaging.

Damage sustained in transit is not covered under warranty.

– Always DISCONNECT THE UPS BATTERY before shipping in compliance with U.S.

Department of Transportation (DOT) and IATA regulations. The battery may remain in the
UPS.

4. Mark the RMA# on the outside of the package.

5. Return the UPS by insured, prepaid carrier to the address given to you by Customer Support.

16 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Two-Year Warranty

The limited warranty provided by American Power Conversion (APC®) in this statement of Limited Factory Warranty applies only to
products you purchase for your commercial or industrial use in the ordinary course of your business.

Terms of warranty

APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. The
obligation of APC under this warranty is limited to repairing or replacing, at its sole discretion, any such defective products. This warranty
does not apply to equipment that has been damaged by accident, negligence or misapplication or has been altered or modified in any way.
Repair or replacement of a defective product or part thereof does not extend the original warranty period. Any parts furnished under this
warranty may be new or factory-remanufactured.

Non-transferable warranty

This warranty extends only to the original purchaser who must have properly registered the product. The product may be registered at the
APC Web site, www.apc.com.

Exclusions

APC shall not be liable under the warranty if its testing and examination disclose that the alleged defect in the product does not exist or was
caused by end user or any third person misuse, negligence, improper installation or testing. Further, APC shall not be liable under the
warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage or connection, inappropriate on-site
operation conditions, corrosive atmosphere, repair, installation, start-up by non-APC designated personnel, a change in location or
operating use, exposure to the elements, Acts of God, fire, theft, or installation contrary to APC recommendations or specifications or in
any event if the APC serial number has been altered, defaced, or removed, or any other cause beyond the range of the intended use.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR OTHERWISE, OF PRODUCTS SOLD,
SERVICED OR FURNISHED UNDER THIS AGREEMENT OR IN CONNECTION HEREWITH. APC DISCLAIMS ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR PURPOSE. APC EXPRESS
WARRANTIES WILL NOT BE ENLARGED, DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL
ARISE OUT OF, APC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN CONNECTION WITH THE
PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES AND REMEDIES. THE WARRANTIES SET FORTH ABOVE CONSTITUTE APC SOLE LIABILITY AND
PURCHASER EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC WARRANTIES EXTEND ONLY TO
PURCHASER AND ARE NOT EXTENDED TO ANY THIRD PARTIES.

IN NO EVENT SHALL APC, ITS OFFICERS, DIRECTORS, AFFILIATES OR EMPLOYEES BE LIABLE FOR ANY FORM OF
INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR
INSTALLATION, OF THE PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF
FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC HAS BEEN ADVISED IN ADVANCE OF THE POSSIBILITY
OF SUCH DAMAGES. SPECIFICALLY, APC IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE, LOSS
OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA, COSTS OF SUBSTITUENTS, CLAIMS
BY THIRD PARTIES, OR OTHERWISE.

NO SALESMAN, EMPLOYEE OR AGENT OF APC IS AUTHORIZED TO ADD TO OR VARY THE TERMS OF THIS WARRANTY.
WARRANTY TERMS MAY BE MODIFIED, IF AT ALL, ONLY IN WRITING SIGNED BY AN APC OFFICER AND LEGAL
DEPARTMENT.

Warranty claims

Customers with warranty claims issues may access the APC customer support network through the Support page of the APC Web site,
www.apc.com/support. Select your country from the country selection pull-down menu. Open the Support tab at the top of the Web page to
obtain contact information for customer support in your region.

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 17

Regulatory Information

Regulatory Agency Approvals and Radio Frequency Warnings

FCC Compliance Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case users will be required to take whatever measures may be necessary to correct the interference at
their own expense.

120/208 V models

LISTED 42C2

E95463

230 V models

geprüfte

N 394

Sicherheit

APC Worldwide Customer Support

Customer support for this or any other APC product is available at no charge in any of the following ways:

• Refer to the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.

– www.apc.com (Corporate Headquarters)

Connect to localized APC Web sites for specific countries, each of which provides customer
support information.

– www.apc.com/support/

Global support searching APC Knowledge Base and using e-support.

• Contact an APC Customer Support center by telephone or e-mail.
Local, country-specific centers:
go to www.apc.com/support/contact for information.

Contact the APC representative or other distributor from whom you purchased your APC product for
information on how to obtain local customer support.

Entire contents copyright 2006 American Power Conversion Corporation. All rights reserved. Reproduction in whole or in part without
permission is prohibited.

APC, the APC logo, Smart-UPS and PowerChute are trademarks of American Power Conversion Corporation. All other trademarks,
product names, and corporate names are the property of their respective owners and are used for informational purposes only.

18 Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual

Date of product declaration

Smart-UPS 2200/3000 VA XL 120/208/230 VAC Tower/Rack-Mount 5U User Manual 19