Apc BX1100LI, BX1100LI-MS User Manual [ru]

bu389b

IEC jumper cable for PC connection

bu389a

bu043h

BX1100LI-MS

BX1100LI

Back-UPS

BX1100LI Series

Safety and General Information

Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damage.

Read the following reminders before installing the UPS.

User Guide

Status Indicators

On-line (Green)

Replace Battery

(Red)

Audible Alarm Condition

On -

Off

On-line - The Back-UPS is supplying AC power to the connected equipment

-On

Constant Tone

On Line Overload - The power being used by the connected equipment has exceeded the capacity of the unit. Disconnect some equipment

On -

Constant beeping

Over-temperature Warning - The unit is overheating and will shut down if the temperature is not lowered. Disconnect some of the connected equipment.

On -

4 beeps repeated

every 30 seconds

On-Battery - The Back-UPS is supplying battery power

Flashing -

Rapid Beeping

(every 1/2 second)

Low Battery Warning - The Back-UPS has 2 minutes of runtime remaining

Flashing Alternately

Constant tone

Bad Battery Detected - The battery needs to be charged, or is at end of life.

- Flashing

Chirp every 2

seconds

Charger Warning - The Back-UPS has experienced an internal problem, but is still providing power to the connected equipment. Contact Schneider Electric IT (SEIT) Technical Support

Off

Short beep every

4 seconds

Low Battery Shutdown - During On Battery operation the battery power was almost completely exhausted, and the Back-UPS is waiting for AC power to return to normal

Constant Tone

On Battery Overload - The connected equipment requires more power than provided by the Back-UPS battery. Unplug devices one at a time to remove overload. If the problem is not corrected, contact SEIT Technical Support

Constant Tone

Charger Fault - Back-UPS has an internal problem. The AC input is present but is no powering the load. Contact SEIT Technical Support

Long beep every

4 seconds

Over-temperature Protected - The Back-UPS has overheated and has shut down. Unplug connected devices one at a time or wait a few hours for system to cool down.

Connect the Battery

™

1 Connect the battery by pulling the battery connector handle

down, and then pushing it into the unit.

2 Replace PC’s input cord with the supplied IEC jumper cable,

and use the PC’s input cord to connect UPS. Note: BX1100LI-MS comes with an extra power cord for connection to a wall outlet.

3 Press the ON/OFF button to turn on the unit.

The green “Power On” indicator confirms that the Back-UPS is on and ready to provide protection.

The Back-UPS should charge for at least 10 hours to ensure sufficient runtime. The unit is being charged whenever it is connected to AC power, whether the unit is turned ON or OFF.

Features

Operational Features

Automatic Voltage Regulation

Automatic Voltage Regulation boosts/trims the AC voltage when it drops/exceeds safe levels. This allows the equipment that is connected to the Back-UPS to operate during low/high voltage conditions, conserving the battery power in the event of a power cut.

The Back-UPS will switch to battery power if the AC input voltage level becomes too low/high for the Automatic Voltage Regulation feature to compensate, or if the AC power is distorted.

If the Back-UPS switches to battery power too frequently or too infrequently, adjust the transfer voltage and sensitivity settings:

1 . Verify that the Back-UPS battery is connected. Connect the Back-UPS to a wall outlet. The

Back-UPS should be turned off.

2 . Press and hold the POWER ON/OFF button for 10 seconds. The LEDs will illuminate green and red

alternately, to indicate that the Back-UPS is in Program mode.

3 . The LEDs will flash either green, red or green and red alternately to indicate the current sensitivity level. The

Back-UPS will beep to indicate that No-load Shutdown is enabled. Refer to the table for an explanation of

the transfer voltage sensitivity levels. 4 . To select LOW sensitivity, press the ON/OFF button until the On Line LED flashes green. 5 . To select MEDIUM sensitivity, press the ON/OFF button until the Battery LED flashes red. 6 . To select HIGH sensitivity, press the ON/OFF button until the On Line and Battery LEDs flash green and

red alternately. 7 . To exit Program mode wait for five seconds and both LEDs will extinguish. Program mode is no longer

active.

No-load Shutdown

The UPS will shut down to conserve energy if while operating on battery power the UPS detects that connected equipment is using less than 15 W of energy for more than 15 minutes.

When the UPS is reconnected to AC power, the UPS will automatically switch on.

Warranty

The standard warranty is two (2) years from the date of purchase. SEIT standard procedure is to replace the original unit with a factory reconditioned unit. Customers who must have the original unit back due to the assignment of asset tags and set depreciation schedules must declare such a need at first contact with an SEIT Technical Support representative. SEIT will ship the replacement unit once the defective unit has been received by the repair department, or cross-ship upon the receipt of a valid credit card number. The customer pays for shipping the unit to SEIT. SEIT pays ground freight transportation costs to ship the replacement unit to the customer.

LED

Flashes

Audible

Indicator

Vo lt ag e

Sensitivity

Setting

Input

Vo lt ag e

Range

No-load

Shutdown Recommended Use

Green None Low 150-280 Disabled Use this setting with equipment that is

less sensitive to fluctuations in voltage or waveform distortions.

Green 4 beeps per

second

Low 150-280 Enabled Use this setting with equipment that is

less sensitive to fluctuations in voltage or waveform distortions.

Red None Medium 155-280 Disabled Use this setting for normal operation

conditions.

Red 4 beeps per

second

Medium (factory default)

155-280 Enabled Use this setting for normal operation

conditions.

Green and Red

None High 160-280 Disabled Use this setting when connected

equipment is sensitive to voltage fluctuations or waveform distortions.

Green and Red

4 beeps per second

High 160-280 Enabled Use this setting when connected

equipment is sensitive to voltage fluctuations or waveform distortions.

Troubleshooting and Service

1 . If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the Schneider

Electric Web site, www.apc.com.

a. Note the model number and serial number and the date of purchase. The model and serial numbers are

located on the rear panel of the unit and are available through the LCD display on select models.

b. Call SEIT Customer Support and a technician will attempt to solve the problem over the phone. If this

is not possible, the technician will issue a Returned Material Authorization Number (RMA#). c. If the unit is under warranty, the repairs are free. d. Service procedures and returns may vary internationally. Refer to the Schneider Electric Web site for

country specific instructions.

2 . Prepare to troubleshoot the problem over the phone. If this is not successful, and the unit is still under

warranty, the Technical Support Representative will provide all necessary information to return the unit for replacement

APC by Schneider Electric IT Customer Support Worldwide

For country specific customer support, go to the APC by Schneider Electric Web site, www.apc.com.

Specification BX1100LI BX1100LI-MS

Input

Voltage 220 - 240 Vac Frequency 50/60 Hz ±3 Hz (Auto-sensing) Brownout Transfer 155 Vac, typical Over-voltage Transfer 280 Vac, typical

Output

UPS Capacity (total) 1100 VA / 550 W Voltage On Battery 230 Vac rms Frequency on Battery 50/60 Hz ± 1 Hz Transfer Time 4 ms typical

Protection

AC Input Resettable circuit breaker

Battery

Type (maintenance free, lead acid)

12 V, 9 AH

Average Life

The battery typically lasts for three to five years.

Environmental factors impact battery life.

Elevated temperatures, high humidity, poor

quality mains power, and frequent, short duration

discharges will shorten battery life.

The battery in the Back-UPS BX1100LI Series

is not user-replaceable. Contact SEIT

Technical Support for a list of authorized

service centers near you.

Typical Recharge Time 6 hours

Physical

Net Weight 8.8 kg 9.2 kg Dimensions (H x W x D) 21.5 cm x 13 cm x 33.6 cm



On Line indicator



Circuit breaker



Battery indicator



Battery Backup + Surge Protection outlets



Power button



AC Power Inlet



Battery connector

Specifications

EN 990-5400-002 06/2014

their affiliated companies. All other trademarks are property of their respective owners.

• This UPS is intended for indoor use only.

• Connect the UPS power cable directly to a wall outlet. Do not use surge protectors or extension cords.

• When grounding cannot be verified, disconnect the equipment from the AC power outlet before installing or connecting to other equipment. Reconnect the power cord after all connections are made.

• Servicing of batteries should be performed by Schneider Electric IT (SEIT) Customer Support only.

• When replacing battery the UPS must be OFF, and its AC inlet unplugged.

• Do not dispose of batteries in a fire. The batteries may explode.

• Do not open or mutilate batteries. They contain an electrolyte that is toxic and harmful to the skin and eyes.

• To avoid harmful injury due to energy hazard, remove wrist watches and jewelry such as rings when replacing the batteries. Use tools with insulated handles.

• Replace batteries with the same number and type of batteries as originally installed in the

equipment.