American Power Conversion 7500-10000 VA User Manual

User Manual

®

®

APC Smart

APC Smart----UPS

APC SmartAPC Smart

7500/10000 VA 200

7500/10000 VA 200----240 VAC 6U

7500/10000 VA 2007500/10000 VA 200

Tower/Rack Mount

Tower/Rack Mount

Tower/Rack MountTower/Rack Mount

Uninterruptible Power Supply

Uninterruptible Power Supply

Uninterruptible Power SupplyUninterruptible Power Supply

UPS

UPSUPS

® ®

240 VAC 6U

240 VAC 6U240 VAC 6U

RT

RT

RTRT

English

990-1216B 02/2004

Introduction

The APC Smart-UPS RT is a high-performance, uninterruptible power system (UPS), designed to
prevent blackouts, brownouts, sags and surges from reaching your computers, servers, and other
sensitive electronic equipment.

1: INSTALLATION

Attention: Read the safety information sheet before installation.

Unpacking

Inspect the UPS upon receipt. Notify the carrier and dealer if there is damage.

The packaging is recyclable; save it for reuse or dispose of it properly.

Check the package contents:

 UPS (with batteries disconnected)

 Two front bezels

 Literature kit containing:

 Software

 Smart-UPS User Manuals CD

 XLI model only: Six output power cords

 Serial cable

 Product documentation, safety and warranty information

 SNMP/Web Card User Manual

Removing the Batteries

The unit is heavy. To lighten the unit, remove the batteries. Refer to the unpacking instructions on
the carton in which the unit is shipped.

Placement

Attention: The UPS is heavy. Select a location sturdy enough to handle the weight.

Do not operate the UPS in excessive dust or in temperature and humidity outside the specified limits.
Ensure the air vents on the front and rear of the UPS are not blocked.
Refer to the APC web site, www.apc.com

1

for details.

Hardwiring

Attention: Wiring must be performed by a qualified electrician.

1. Install a utility circuit breaker in accordance with local electrical codes (see tables below) for
input wiring only.

2. Switch the UPS input circuit breaker (see A) and utility circuit breakers OFF.

3. Remove the access panel (see B).

4. Remove circular knockouts.

5. Run wires through access panel to terminal blocks. Wire to ground block first. Adhere to all
national and local electrical codes. (See tables and graphics.)

6. Use appropriate glands to achieve strain-relief on the hardwired input and output power cables.

XLT, XLJ, AND XLTW MODELS

Input Connection Output Connection (optional)

Wire to L1, L2, and .

System Wiring Voltage Current

SURT7500XLJ,
SURT7500XLT,
SURT7500XLTW

SURT10000XLJ,
SURT10000XLT,
SURT10000XLTW

Input & Output 200/208/220V 40 amps

Input & Output 200/208/220V 54 amps

Wire to L1A, L2A, and

Full Load
(Nominal)

XLTW- 38 amps

XLTW-50 amps

XLI MODELS

Input Connections Output Connection (optional)

Single-Phase: Wire to L1, N, and .

Three-Phase: Wire to L1, L2, L3, N, and

System Wiring Number

SURT7500XLI

SURT10000XLI

Input 1 220/230/240V 38 amps 50 amps / 2-pole 10mm2

Input 3+

Output 1 220/230/240V 38 amps (not required) 10mm

Input 1 220/230/240V 50 amps 63 amps / 2-pole 16mm2

Input 3+

Output 1 220/230/240V 50 amps (not required) 16mm

of
Phases

Neutral

Neutral

.

Voltage Current

380/400/415V 14 amps / phase when

380/400/415V 18 amps / phase when

Wire to L1A, N1, and

Full Load
(Nominal)

online, 38 amps on L1
in bypass

online, 50 amps on L1
in bypass

.

External Input
Circuit Breaker
(typical)

50 amps / 2-pole for
Input Wiring Only

70 amps / 2-pole for
Input Wiring only

.

External Input
Circuit Breaker
(typical)

50 amps / 4-pole 10mm2

63 amps / 4-pole 16mm2

Wire Size
(typical)

#8AWG/

2

10mm

#6AWG/

2

16mm

Wire Size
(typical)

2

2

2

A

A

7. XLI model only: For three-phase input, set the Input Phase Selector switch (see C) to ‘3’. For
single-phase input, leave switch in default position of ‘1’.

XLT/XLJ/XLTW MODELS

OUTPUT

L1A

L2A

INPUT

L1

L2

B

XLI MODEL

UTPUT

O

L1A

N1

INPUT

L1

L2

L3

N

C

B

8. Switch the circuit breakers ON.

9. Check line voltages.

10. Replace the access panel.

3

Installing and Connecting the Batteries and Attaching the Front Bezel

 

 

 

4

C

ONNECTING POWER AND EQUIPMENT TO THE UPS

1. Hardwire the UPS (see Hardwiring).

2. Connect equipment to the UPS (cables not included for XLT/XLJ/XLTW models).

3. Turn on all connected equipment. To use the UPS as a master on/off switch, be sure that all
connected equipment is switched ON.

4. Press the

• The battery charges to 90% capacity during the first three hours of normal operation. Do not

button on the front panel to power up the UPS.

expect full battery run capability during this initial charge period.

5. Configure the Web/SNMP management card (optional).

PTIONS

O

Refer to the APC web site, www.apc.com

 External Battery Pack SURT192XLBP

 Rail Kit SURTRK2

 Isolation Transformer

 Service Bypass Panel

IRCUIT BREAKERS

C

Input Circuit Breaker
7500/10000 VA

The UPS is protected from extreme overloads when in ON position.
The breaker must be on for the UPS to operate.

for available accessories.

XLI/XLJ/XLT/XLTW

Output Circuit Breaker
7500/10000 VA
XLJ/XLT/XLTW

L6-20
250V 20A

L6-30
250V 30A

Output Circuit Breaker
7500/10000 VA XLI

IEC 320-C13
10A for each
receptacle

IEC 320-C19
16A for each
receptacle

5