National Conventions ......................................................................................................................................... 3
Contents in Box ................................................................................................................................................. 8
Connecting the Monitor .................................................................................................................................... 12
Windows XP ............................................................................................................................................. 17
Windows ME/2000 .................................................................................................................................... 18
Color Setup ............................................................................................................................................... 28
Extra ........................................................................................................................................................ 3 4
Windows Vista ..........................................................................................................................................
Windows XP .............................................................................................................................................
Windows 2000
Windows ME .............................................................................................................................................51
General Specification .......................................................................................................................................56
Warranty Statement for Europe .......................................................................................................................63
Warranty Statement for North & South America (excluding Brazil) ...........................................................63
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some
warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific
presentation of the warning is mandated by regulatory authority.
Using"Mobile High-Defintion Link"
4
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure
of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug
will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire
plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat
the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect
the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V ~, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license (Only for
monitors with power adapter).
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and
use mounting accessories recommended by the manufacturer. A product and cart combination should be moved
with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or
electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on
the stand:
6
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of
strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough
as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
7
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and
contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
Setup
8
Contents ofthe Box
Monitor
*
CD Manual
Power Cable
Base
*
Analog Cable
Adapter
*
Audio Cable
MHL Cable
*
HDMI Cable
Not all signal cables (VGA,
check with the local dealer or AOC branch office for confirmation.
and HDMI cables) will be provided for all countries and regions. Please
Setup Stand & Base
9
Please setup or remove the base following the steps as below.
Setup:
2
1
Remove:
10
Unit standing without base is available. (Caution: must put unit in flat surface. Any uneven or sloped surface may
result unit damaged or injury to user.)
11
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your
own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
You are able to adjust the monitor's angle from -5° to 15°.
5
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
1
5
12
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
1
2
Power
1.
2.
3.
Audio port
4.
56. HDMI1/MHL port
.
HDMI2 port
To protect equipment, always turn off the PC and LCD monitor before connecting.
1 Connect the power cable to the AC port on the back of the monitor.
2 Connect one end of the 15-pin D-Sub/HDMIport to the back of the monitor and connect the other end to the
3 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.
Earphone
D-Sub port
computer's D-Sub/HDMI or mobile MHL port.
3
4
5
6
13
Adjusting
Setting Optimal Resolution
Windows 8
For Windows 8:
1. Right click and click All apps at the bottom-right of the screen.
2. Click “Control Panel".
3. Set the “view by” to “Category”.
4.
Click Appearance and Personalization.
5. Click DISPLAY.
14
6. Set the resolution SLIDE-BAR to 1920x1080
.
.
Windows Vista
15
For Windows Vista:
1 Click STAR T.
2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization
5 Click Display Settings.
16
6 Set the resolution SLIDE-BAR to 1920 by 1080.
Windows XP
17
For Windows XP:
1 Click STAR T.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Click Appearance and Themes.
5 Double click DISPLAY.
6 Click SETTINGS.
18
7 Set the resolution SLIDE-BAR to 1920 by 1080.
Windows ME/2000
For Windows ME/2000:
1 Click STAR T.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Double click DISPLAY.
5 Click SETTINGS.
6 Set the resolution SLIDE-BAR to 1920 by 1080.
Hotkeys
19
1
1
Source/Auto/Exit
2
ClearVision/
Volume/ >
3
4 Menu/Enter
5 Power
Power
Press the Power button to turn on/off the monitor.
Volume />
When there is no OSD, press Volumeadjust volume.
Auto / Exit / Source hot key
When there is no OSD, press Auto/Source button continuously about 2 second to do auto configure.
When the OSD is closed, press Source button will be Source hot key function. Press Source button continuously to
select the input source showed in the message bar, press Menu/Enter button to change to the source selected.
>
2
3
45
Using "MHL(Mobile High-Definition Link)"
20
1. "MHL" (Mobile High-Definition Link)
This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the
screen of
z To use the MHL function, you need an MHL-certified mobile device. You can check if your mobile device is MHL
z To use the MHL function, the latest version of software must be installed on the mobile device.
z On some mobile devices, the MHL function may not be available depending on the device's performance or
z Since the display size of the product is larger than those of mobile devices, the picture quality may degrade.
z This product is officially MHL-certified. If you encounter any problem when using the MHL function, please contact the
z The picture quality may degrade when content (imported from the mobile device) with a low
the product.
certified on the device manufacturer's website. To find a list of MHL-certified devices, visit the official MHL website
(http://www.mhlconsortium.org).
functionality.
manufacturer of the mobile device.
Resolution is played on the product.
Using "MHL"
1. Connect the micro USB port on the mobile device to the [HDMI 1 / MHL] port on the product using the MHL cable.
z When the MHL cable is used, [HDMI 1/ MHL] is the only port on this monitor that supports the MHL function.
z Mobile device must be purchased separately.
2. Connect the DC power adapter to the product and a power outlet.
3. Press the source button
4. After about 3 seconds, the MHL screen will be displayed if MHL mode is active.
Remark: The indicated time "3 sec later" may vary depending on the mobile device.
and switch to HDMI 1/MHL to activate MHL mode.
When the mobile device is not connected or does not support MHL
z If MHL mode is not activated, check the connection of the mobile device.
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.