Anton-Bauer Twin Two Position Charger User Manual

®

TWIN

SIMULTANEOUS

TWO POSITION CHARGER

OWNER’S MANUAL

INTRODUCTION

The TWIN is a simultaneous Two Position charger for all Anton/Bauer® Gold Mount®
Batteries. Its lightweight and small size makes it an ideal charger for travel. As a
simultaneous charger each position operates independently allowing two batteries to charge
at the same time (see battery charge times pg 5.).

The TWIN is fully compatible with all current and future Anton/Bauer Logic Series

®

batteries and delivers all the advancements and pro ven reliability of InterActive

charging.

®

Like all Anton/Bauer chargers, everything is automatic. Once a battery is placed on the
TWIN, the charger will evaluate the battery and then execute the proper charge routine.

STANDARD FEATURES

• Simultaneous Charging for all Anton/Bauer Logic Series bat teries.

• Full InterActive technology including six simultaneous charge termination

systems, Balance and Rejuvenation modes, and LifeSaver

®

Maintenance mode.

• Wide range mains input compatibility (90-250 VAC 50-60 Hz) automatically adapts

to any mains source worldwide.

• Expanded InterActive communications with DIGITAL batteries, anticipating new

cell technologies.

• Slim, ultra-lightweight design for easy portability.

This unit was packaged at the factory to arrive intact at its destination. If there
is any damage to the packaging or the unit when received, please notify the
carrier immediately.

SAFEGUARDS

Power Sources: This unit was designed to operate at mains voltages from

90 to 250 Volts AC, 50-60 Hz.

Risk of Electrical Shock: Refer servicing to qualified service personnel.
Important: When powering charger using a generator, the generator must

produce a

sine wave or modified sine wave output, otherwise the charger may be damaged.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.

1

GROUNDING/EARTHING

IMPORTANT WARNING: THIS APPARATUS MUST BE EARTHED.

To ensure safe operation, the three pin plug supplied must be inserted only into a
standard three-pin power point that is effectively grounded through the normal
household wiring. Extension cords used with the equipment must be three-conductor
and be correctly wired to provide connection to earth ground. Improperly wired
extension cords are a dangerous electrical hazard.

The fact that the equipment operates satisfactorily does not imply that the power point is
properly grounded and that the installation is completely safe. If any doubt exists about
the correct grounding of the power point, consult a qualified electrician.

IMPORTANT: The wires in this main lead are colored in accordance with the

following code:

Green and yellow Earth
Blue Neutral
Brown Live

OPERATION

Self-Test

Upon applying mains power, each TWIN will initiate a self-test mode. This mode is
indicated by the LED’s on the unit. Each positio n will light the red LED followed by the
green LED. Upon completion of the self-test, the green status light will light steadily,
indicating that the unit is ready for operation.

Charging

As with all Anton/Bauer chargers, charging with TWIN is fully automatic. Mount any
applicable battery to any open Gold Mount position on the charger and it will
automatically determine the appropriate charge routine and execute it.

IMPORTANT: In order to ensure correct operation when charging the Titan Twin

should be positioned with cooling vents vertical as shown in the Figure
on page 1.

Applications

The TWIN models will charge any combination of Anton/Bauer Logic Series Gold
Mount batteries including models: ProPac

®

ProFormer
Dionic and InterActive 2000

, Digital ProPac 13/14, Digital Compac 13/14, Digital Trimpac 13/14,

™

HyTRON™ batteries.

Each TWIN incorporates the exclusive Anton/Bauer InterActive communication
between battery and charger, which allows the charger to identify any Anton/Bauer
battery attached and determine the precise charge routine for that battery under the
prevailing conditions.

®

13/14, Compac® 13/14, Trimpac® 13/14,

2